diff mbox series

[1/2] ARM: dts: qcom-apq8064: Collapse usb support into one node

Message ID 1494623898-27230-2-git-send-email-john.stultz@linaro.org
State New
Headers show
Series Few DTS changes needed for Nexus7 support | expand

Commit Message

John Stultz May 12, 2017, 9:18 p.m. UTC 
From: Stephen Boyd <stephen.boyd@linaro.org>


We currently have three device nodes for the same USB hardware
block, as evident by the reuse of the same reg address multiple
times. Now that the chipidea driver fully supports OTG with the
MSM wrapper we can collapse the three nodes into one USB device
node, reflecting the true nature of the hardware.

Since we're here, we also mark the irq trigger flags correctly,
as IRQ_TYPE_LEVEL_HIGH instead of IRQ_TYPE_NONE.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Vinay Simha <simhavcs@gmail.com>
Cc: David Brown <david.brown@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>

Signed-off-by: John Stultz <john.stultz@linaro.org>

---
 .../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts |  49 +++----
 arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts |  21 +--
 arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts        |  54 ++++----
 arch/arm/boot/dts/qcom-apq8064-ifc6410.dts         |  54 ++++----
 .../arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts |  16 +--
 arch/arm/boot/dts/qcom-apq8064.dtsi                | 154 ++++++++++++---------
 6 files changed, 169 insertions(+), 179 deletions(-)

-- 
2.7.4

Comments

Bjorn Andersson May 14, 2017, 3:23 a.m. UTC | #1 
On Fri 12 May 14:18 PDT 2017, John Stultz wrote:

> From: Stephen Boyd <stephen.boyd@linaro.org>

> 

> We currently have three device nodes for the same USB hardware

> block, as evident by the reuse of the same reg address multiple

> times. Now that the chipidea driver fully supports OTG with the

> MSM wrapper we can collapse the three nodes into one USB device

> node, reflecting the true nature of the hardware.

> 

> Since we're here, we also mark the irq trigger flags correctly,

> as IRQ_TYPE_LEVEL_HIGH instead of IRQ_TYPE_NONE.

> 

> Cc: Bjorn Andersson <bjorn.andersson@linaro.org>


Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>


Regards,
Bjorn
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
index 8f5de02..c5f561f 100644
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
@@ -319,44 +319,37 @@ 
 			target-supply	= <&pm8921_lvs7>;
 		};
 
-		/* OTG */
-		phy@12500000 {
-			status		= "okay";
-			dr_mode		= "peripheral";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l4>;
-		};
-
-		phy@12520000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l23>;
-		};
-
-		phy@12530000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l23>;
-		};
-
-		gadget@12500000 {
-			status = "okay";
-		};
-
-		/* OTG */
 		usb@12500000 {
 			status = "okay";
+			dr_mode = "peripheral";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l4>;
+				};
+			};
 		};
 
 		usb@12520000 {
 			status = "okay";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
 		};
 
 		usb@12530000 {
 			status = "okay";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
 		};
 
 		amba {
diff --git a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
index e39440a..e5fef32 100644
--- a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
@@ -320,22 +320,15 @@ 
 			};
 		};
 
-		/* OTG */
-		phy@12500000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l4>;
-			dr_mode		= "otg";
-		};
-
-		gadget@12500000 {
-			status = "okay";
-		};
-
-		/* OTG */
 		usb@12500000 {
 			status = "okay";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l4>;
+				};
+			};
 		};
 
 		amba {
diff --git a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
index 35f1d46..d736203 100644
--- a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
@@ -149,43 +149,37 @@ 
 			};
 		};
 
-		/* OTG */
-		usb1_phy: phy@12500000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l4>;
-		};
-
-		usb3_phy: phy@12520000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l23>;
-		};
-
-		usb4_phy: phy@12530000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l23>;
-		};
-
-		gadget1: gadget@12500000 {
-			status = "ok";
-		};
-
-		/* OTG */
-		usb1: usb@12500000 {
+		usb@12500000 {
 			status = "ok";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l4>;
+				};
+			};
 		};
 
-		usb3: usb@12520000 {
+		usb@12520000 {
 			status = "okay";
+			dr_mode = "host";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
 		};
 
-		usb4: usb@12530000 {
+		usb@12530000 {
 			status = "okay";
+			dr_mode = "host";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
 		};
 
 		/* on board fixed 3.3v supply */
diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
index 881ce70..bbd1dac 100644
--- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
@@ -243,43 +243,37 @@ 
 			target-supply	= <&pm8921_s4>;
 		};
 
-		/* OTG */
-		usb1_phy: phy@12500000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l4>;
-		};
-
-		usb3_phy: phy@12520000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l23>;
-		};
-
-		usb4_phy: phy@12530000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l23>;
-		};
-
-		gadget1: gadget@12500000 {
-			status = "okay";
-		};
-
-		/* OTG */
-		usb1: usb@12500000 {
+		usb@12500000 {
 			status = "okay";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l4>;
+				};
+			};
 		};
 
-		usb3: usb@12520000 {
+		usb@12520000 {
 			status = "okay";
+			dr_mode = "host";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
 		};
 
-		usb4: usb@12530000 {
+		usb@12530000 {
 			status = "okay";
+			dr_mode = "host";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
 		};
 
 		pci@1b500000 {
diff --git a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
index a34ba35..88a9aff4 100644
--- a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
@@ -349,15 +349,15 @@ 
 			};
 		};
 
-		phy@12500000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l4>;
-		};
-
-		gadget@12500000 {
+		usb@12500000 {
 			status = "okay";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l4>;
+				};
+			};
 		};
 
 		gsbi@1a200000 {
diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
index 14a6f5e..f3db185 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
@@ -197,7 +197,7 @@ 
 			clock-frequency = <27000000>;
 		};
 
-		sleep_clk {
+		sleep_clk: sleep_clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <32768>;
@@ -884,81 +884,97 @@ 
 			};
 		};
 
-		usb1_phy: phy@12500000 {
-			compatible	= "qcom,usb-otg-ci";
-			reg		= <0x12500000 0x400>;
-			interrupts	= <GIC_SPI 100 IRQ_TYPE_NONE>;
-			status		= "disabled";
-
-			clocks		= <&gcc USB_HS1_XCVR_CLK>,
-					  <&gcc USB_HS1_H_CLK>;
-			clock-names	= "core", "iface";
-
-			resets		= <&gcc USB_HS1_RESET>;
-			reset-names	= "link";
-		};
-
-		usb3_phy: phy@12520000 {
-			compatible	= "qcom,usb-otg-ci";
-			reg		= <0x12520000 0x400>;
-			interrupts	= <GIC_SPI 188 IRQ_TYPE_NONE>;
-			status		= "disabled";
-			dr_mode		= "host";
-
-			clocks		= <&gcc USB_HS3_XCVR_CLK>,
-					  <&gcc USB_HS3_H_CLK>;
-			clock-names	= "core", "iface";
-
-			resets		= <&gcc USB_HS3_RESET>;
-			reset-names	= "link";
-		};
-
-		usb4_phy: phy@12530000 {
-			compatible	= "qcom,usb-otg-ci";
-			reg		= <0x12530000 0x400>;
-			interrupts	= <GIC_SPI 215 IRQ_TYPE_NONE>;
-			status		= "disabled";
-			dr_mode		= "host";
-
-			clocks		= <&gcc USB_HS4_XCVR_CLK>,
-					  <&gcc USB_HS4_H_CLK>;
-			clock-names	= "core", "iface";
-
-			resets		= <&gcc USB_HS4_RESET>;
-			reset-names	= "link";
-		};
-
-		gadget1: gadget@12500000 {
-			compatible	= "qcom,ci-hdrc";
-			reg		= <0x12500000 0x400>;
-			status		= "disabled";
-			dr_mode		= "peripheral";
-			interrupts	= <GIC_SPI 100 IRQ_TYPE_NONE>;
-			usb-phy		= <&usb1_phy>;
-		};
-
 		usb1: usb@12500000 {
-			compatible	= "qcom,ehci-host";
-			reg		= <0x12500000 0x400>;
-			interrupts	= <GIC_SPI 100 IRQ_TYPE_NONE>;
-			status		= "disabled";
-			usb-phy		= <&usb1_phy>;
+			compatible = "qcom,ci-hdrc";
+			reg = <0x12500000 0x200>,
+			      <0x12500200 0x200>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>;
+			clock-names = "core", "iface";
+			assigned-clocks = <&gcc USB_HS1_XCVR_CLK>;
+			assigned-clock-rates = <60000000>;
+			resets = <&gcc USB_HS1_RESET>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			ahb-burst-config = <0>;
+			phys = <&usb_hs1_phy>;
+			phy-names = "usb-phy";
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs1_phy: phy {
+					compatible = "qcom,usb-hs-phy-apq8064",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&sleep_clk>, <&cxo_board>;
+					clock-names = "sleep", "ref";
+					resets = <&usb1 0>;
+					reset-names = "por";
+				};
+			};
 		};
 
 		usb3: usb@12520000 {
-			compatible	= "qcom,ehci-host";
-			reg		= <0x12520000 0x400>;
-			interrupts	= <GIC_SPI 188 IRQ_TYPE_NONE>;
-			status		= "disabled";
-			usb-phy		= <&usb3_phy>;
+			compatible = "qcom,ci-hdrc";
+			reg = <0x12520000 0x200>,
+			      <0x12520200 0x200>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc USB_HS3_XCVR_CLK>, <&gcc USB_HS3_H_CLK>;
+			clock-names = "core", "iface";
+			assigned-clocks = <&gcc USB_HS3_XCVR_CLK>;
+			assigned-clock-rates = <60000000>;
+			resets = <&gcc USB_HS3_RESET>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			ahb-burst-config = <0>;
+			phys = <&usb_hs3_phy>;
+			phy-names = "usb-phy";
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs3_phy: phy {
+					compatible = "qcom,usb-hs-phy-apq8064",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&sleep_clk>, <&cxo_board>;
+					clock-names = "sleep", "ref";
+					resets = <&usb3 0>;
+					reset-names = "por";
+				};
+			};
 		};
 
 		usb4: usb@12530000 {
-			compatible	= "qcom,ehci-host";
-			reg		= <0x12530000 0x400>;
-			interrupts	= <GIC_SPI 215 IRQ_TYPE_NONE>;
-			status		= "disabled";
-			usb-phy		= <&usb4_phy>;
+			compatible = "qcom,ci-hdrc";
+			reg = <0x12530000 0x200>,
+			      <0x12530200 0x200>;
+			interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc USB_HS4_XCVR_CLK>, <&gcc USB_HS4_H_CLK>;
+			clock-names = "core", "iface";
+			assigned-clocks = <&gcc USB_HS4_XCVR_CLK>;
+			assigned-clock-rates = <60000000>;
+			resets = <&gcc USB_HS4_RESET>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			ahb-burst-config = <0>;
+			phys = <&usb_hs4_phy>;
+			phy-names = "usb-phy";
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs4_phy: phy {
+					compatible = "qcom,usb-hs-phy-apq8064",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&sleep_clk>, <&cxo_board>;
+					clock-names = "sleep", "ref";
+					resets = <&usb4 0>;
+					reset-names = "por";
+				};
+			};
 		};
 
 		sata_phy0: phy@1b400000 {