| Message ID | 1530259891-18822-2-git-send-email-hayashi.kunihiko@socionext.com |
|---|---|
| State | New |
| Headers | show |
| Series | reset: uniphier: add USB3 controller reset support | expand |
On Fri, Jun 29, 2018 at 05:11:30PM +0900, Kunihiko Hayashi wrote: > Add DT bindings for reset control of USB3 controller implemented in > UniPhier SoCs. > > Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> > --- > .../devicetree/bindings/reset/uniphier-reset.txt | 45 ++++++++++++++++++++++ > 1 file changed, 45 insertions(+) > > diff --git a/Documentation/devicetree/bindings/reset/uniphier-reset.txt b/Documentation/devicetree/bindings/reset/uniphier-reset.txt > index 93efed6..f21d81c 100644 > --- a/Documentation/devicetree/bindings/reset/uniphier-reset.txt > +++ b/Documentation/devicetree/bindings/reset/uniphier-reset.txt > @@ -118,3 +118,48 @@ Example: > > other nodes ... > }; > + > + > +USB3 controller reset > +--------------------- > + > +Required properties: > +- compatible: Should be > + "socionext,uniphier-pro4-usb3-reset" - for Pro4 SoC > + "socionext,uniphier-pxs2-usb3-reset" - for PXs2 SoC > + "socionext,uniphier-ld20-usb3-reset" - for LD20 SoC > + "socionext,uniphier-pxs3-usb3-reset" - for PXs3 SoC > +- #reset-cells: Should be 1. > +- reg: Specifies offset and length of the register set for the device. > +- clocks: A list of phandles to the clock gate for USB3 glue layer. > + According to the clock-names, appropriate clocks are required. > +- clock-names: Should contain > + "gio", "link" - for Pro4 SoC > + "link" - for others > +- resets: A list of phandles to the reset control for USB3 glue layer. > + According to the reset-names, appropriate resets are required. > +- reset-names: Should contain > + "gio", "link" - for Pro4 SoC > + "link" - for others > + > +Example: > + > + usb-glue@65b00000 { > + compatible = "socionext,uniphier-ld20-dwc3-glue", > + "simple-mfd"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges = <0 0x65b00000 0x400>; > + > + usb_rst: reset@0 { > + compatible = "socionext,uniphier-ld20-usb3-reset"; This looks weird. You have a reset controller within the USB block? And then a parent reset controller too? > + reg = <0x0 0x4>; > + #reset-cells = <1>; > + clock-names = "link"; > + clocks = <&sys_clk 14>; > + clock-names = "link"; > + resets = <&sys_rst 14>; > + }; > + > + other nodes ... What other nodes? > + }; > -- > 2.7.4 > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Rob, On Tue, 3 Jul 2018 17:37:47 -0600 <robh@kernel.org> wrote: > On Fri, Jun 29, 2018 at 05:11:30PM +0900, Kunihiko Hayashi wrote: > > Add DT bindings for reset control of USB3 controller implemented in > > UniPhier SoCs. > > > > Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> > > --- > > .../devicetree/bindings/reset/uniphier-reset.txt | 45 ++++++++++++++++++++++ > > 1 file changed, 45 insertions(+) > > > > diff --git a/Documentation/devicetree/bindings/reset/uniphier-reset.txt b/Documentation/devicetree/bindings/reset/uniphier-reset.txt > > index 93efed6..f21d81c 100644 > > --- a/Documentation/devicetree/bindings/reset/uniphier-reset.txt > > +++ b/Documentation/devicetree/bindings/reset/uniphier-reset.txt > > @@ -118,3 +118,48 @@ Example: > > > > other nodes ... > > }; > > + > > + > > +USB3 controller reset > > +--------------------- > > + > > +Required properties: > > +- compatible: Should be > > + "socionext,uniphier-pro4-usb3-reset" - for Pro4 SoC > > + "socionext,uniphier-pxs2-usb3-reset" - for PXs2 SoC > > + "socionext,uniphier-ld20-usb3-reset" - for LD20 SoC > > + "socionext,uniphier-pxs3-usb3-reset" - for PXs3 SoC > > +- #reset-cells: Should be 1. > > +- reg: Specifies offset and length of the register set for the device. > > +- clocks: A list of phandles to the clock gate for USB3 glue layer. > > + According to the clock-names, appropriate clocks are required. > > +- clock-names: Should contain > > + "gio", "link" - for Pro4 SoC > > + "link" - for others > > +- resets: A list of phandles to the reset control for USB3 glue layer. > > + According to the reset-names, appropriate resets are required. > > +- reset-names: Should contain > > + "gio", "link" - for Pro4 SoC > > + "link" - for others > > + > > +Example: > > + > > + usb-glue@65b00000 { > > + compatible = "socionext,uniphier-ld20-dwc3-glue", > > + "simple-mfd"; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + ranges = <0 0x65b00000 0x400>; > > + > > + usb_rst: reset@0 { > > + compatible = "socionext,uniphier-ld20-usb3-reset"; > > This looks weird. You have a reset controller within the USB block? And > then a parent reset controller too? Yes, this reset control is included in USB3 glue layer, and this is necessary to enable USB3 core. The following diagram shows those relationships. USB3 block | +---USB3 glue layer | | | +--- usb3-reset | | | +--- usb3-regluator | | | +--- usb3-phy | +---USB3 core The system reset, as parent reset controller, is necessary to enable the entire USB3 block including the glue layer. > > + reg = <0x0 0x4>; > > + #reset-cells = <1>; > > + clock-names = "link"; > > + clocks = <&sys_clk 14>; > > + clock-names = "link"; > > + resets = <&sys_rst 14>; > > + }; > > + > > + other nodes ... > > What other nodes? As mentioned above, the glue layer consists of reset, regulator, and phy. I assume that the "other nodes" mean that these nodes are placed. Thank you, --- Best Regards, Kunihiko Hayashi -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/reset/uniphier-reset.txt b/Documentation/devicetree/bindings/reset/uniphier-reset.txt index 93efed6..f21d81c 100644 --- a/Documentation/devicetree/bindings/reset/uniphier-reset.txt +++ b/Documentation/devicetree/bindings/reset/uniphier-reset.txt @@ -118,3 +118,48 @@ Example: other nodes ... }; + + +USB3 controller reset +--------------------- + +Required properties: +- compatible: Should be + "socionext,uniphier-pro4-usb3-reset" - for Pro4 SoC + "socionext,uniphier-pxs2-usb3-reset" - for PXs2 SoC + "socionext,uniphier-ld20-usb3-reset" - for LD20 SoC + "socionext,uniphier-pxs3-usb3-reset" - for PXs3 SoC +- #reset-cells: Should be 1. +- reg: Specifies offset and length of the register set for the device. +- clocks: A list of phandles to the clock gate for USB3 glue layer. + According to the clock-names, appropriate clocks are required. +- clock-names: Should contain + "gio", "link" - for Pro4 SoC + "link" - for others +- resets: A list of phandles to the reset control for USB3 glue layer. + According to the reset-names, appropriate resets are required. +- reset-names: Should contain + "gio", "link" - for Pro4 SoC + "link" - for others + +Example: + + usb-glue@65b00000 { + compatible = "socionext,uniphier-ld20-dwc3-glue", + "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x65b00000 0x400>; + + usb_rst: reset@0 { + compatible = "socionext,uniphier-ld20-usb3-reset"; + reg = <0x0 0x4>; + #reset-cells = <1>; + clock-names = "link"; + clocks = <&sys_clk 14>; + clock-names = "link"; + resets = <&sys_rst 14>; + }; + + other nodes ... + };
Add DT bindings for reset control of USB3 controller implemented in UniPhier SoCs. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> --- .../devicetree/bindings/reset/uniphier-reset.txt | 45 ++++++++++++++++++++++ 1 file changed, 45 insertions(+) -- 2.7.4 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html