new file mode 100644
@@ -0,0 +1,202 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/rohm,bd71815-pmic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ROHM BD71815 Power Management Integrated Circuit bindings
+
+maintainers:
+ - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
+
+description: |
+ BD71815AGW is a single-chip power management ICs for battery-powered
+ portable devices. It integrates 5 buck converters, 8 LDOs, a boost driver
+ for LED and a 500 mA single-cell linear charger. Also included is a Coulomb
+ counter, a real-time clock (RTC), and a 32.768 kHz clock gate and two GPOs.
+
+properties:
+ compatible:
+ const: rohm,bd71815
+
+ reg:
+ description:
+ I2C slave address.
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ gpio-controller: true
+
+ "#gpio-cells":
+ const: 2
+ description: |
+ The first cell is the pin number and the second cell is used to specify
+ flags. See ../gpio/gpio.txt for more information.
+
+ clocks:
+ maxItems: 1
+
+ "#clock-cells":
+ const: 0
+
+ clock-output-names:
+ const: bd71815-32k-out
+
+ rohm,clkout-open-drain:
+ description: clk32kout mode. Set to 1 for "open-drain" or 0 for "cmos".
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 1
+
+ rohm,charger-sense-resistor-ohms:
+ minimum: 10000000
+ maximum: 50000000
+ description: |
+ BD71827 and BD71828 have SAR ADC for measuring charging currents.
+ External sense resistor (RSENSE in data sheet) should be used. If
+ something other but 30MOhm resistor is used the resistance value
+ should be given
+ here in Ohms.
+ default: 30000000
+
+ regulators:
+ $ref: ../regulator/rohm,bd71815-regulator.yaml
+ description:
+ List of child nodes that specify the regulators.
+
+ gpio-reserved-ranges:
+ description: |
+ Usage of BD71828 GPIO pins can be changed via OTP. This property can be
+ used to mark the pins which should not be configured for GPIO. Please see
+ the ../gpio/gpio.txt for more information.
+
+ rohm,enable-hidden-gpo:
+ description: |
+ The BD71815 has undocumented GPO at pin E5. Pin is marked as GND at the
+ data-sheet as it's location in the middle of GND pins makes it hard to
+ use on PCB. If your board has managed to use this pin you can enable the
+ second GPO by defining this property. Dont enable this if you are unsure
+ about how the E5 pin is connected on your board.
+ type: boolean
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - "#clock-cells"
+ - regulators
+ - gpio-controller
+ - "#gpio-cells"
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/leds/common.h>
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pmic: pmic@4b {
+ compatible = "rohm,bd71815";
+ reg = <0x4b>;
+
+ interrupt-parent = <&gpio1>;
+ interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+
+ clocks = <&osc 0>;
+ #clock-cells = <0>;
+ clock-output-names = "bd71815-32k-out";
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ rohm,charger-sense-resistor-ohms = <10000000>;
+
+ regulators {
+ buck1: buck1 {
+ regulator-name = "buck1";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ rohm,dvs-run-voltage = <1150000>;
+ rohm,dvs-suspend-voltage = <950000>;
+ };
+ buck2: buck2 {
+ regulator-name = "buck2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ rohm,dvs-run-voltage = <1150000>;
+ rohm,dvs-suspend-voltage = <950000>;
+ };
+ buck3: buck3 {
+ regulator-name = "buck3";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <2700000>;
+ regulator-always-on;
+ };
+ buck4: buck4 {
+ regulator-name = "buck4";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1850000>;
+ regulator-always-on;
+ };
+ buck5: buck5 {
+ regulator-name = "buck5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ ldo1: ldo1 {
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ ldo2: ldo2 {
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ ldo3: ldo3 {
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ ldo4: ldo4 {
+ regulator-name = "ldo4";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ ldo5: ldo5 {
+ regulator-name = "ldo5";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ ldo6: ldodvref {
+ regulator-name = "ldodvref";
+ regulator-always-on;
+ };
+ ldo7: ldolpsr {
+ regulator-name = "ldolpsr";
+ regulator-always-on;
+ };
+
+ boost: wled {
+ regulator-name = "wled";
+ regulator-min-microamp = <10>;
+ regulator-max-microamp = <25000>;
+ };
+ };
+ };
+ };
Document DT bindings for ROHM BD71815. BD71815 is a single-chip power management IC mainly for battery-powered portable devices. The IC integrates 5 bucks, 7 LDOs, a boost driver for LED, a battery charger with a Coulomb counter, a real-time clock, a 32kHz clock and two general-purpose outputs although only one is documented by the data-sheet. Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> --- Changes since v1: - fixed patch ordering to meet ref dependencies - added missing blank lines - clkout-mode changed from string to tristated (uint) - added default for rsense resistor .../bindings/mfd/rohm,bd71815-pmic.yaml | 202 ++++++++++++++++++ 1 file changed, 202 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml