[22/54] dt-bindings: media: Convert OV5640 binding to a schema

diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
deleted file mode 100644
index c97c2f2da12d..000000000000
--- a/Documentation/devicetree/bindings/media/i2c/ov5640.txt
+++ /dev/null
@@ -1,92 +0,0 @@ 
-* Omnivision OV5640 MIPI CSI-2 / parallel sensor
-
-Required Properties:
-- compatible: should be "ovti,ov5640"
-- clocks: reference to the xclk input clock.
-- clock-names: should be "xclk".
-- DOVDD-supply: Digital I/O voltage supply, 1.8 volts
-- AVDD-supply: Analog voltage supply, 2.8 volts
-- DVDD-supply: Digital core voltage supply, 1.5 volts
-
-Optional Properties:
-- reset-gpios: reference to the GPIO connected to the reset pin, if any.
-	       This is an active low signal to the OV5640.
-- powerdown-gpios: reference to the GPIO connected to the powerdown pin,
-		   if any. This is an active high signal to the OV5640.
-- rotation: as defined in
-	    Documentation/devicetree/bindings/media/video-interfaces.txt,
-	    valid values are 0 (sensor mounted upright) and 180 (sensor
-	    mounted upside down).
-
-The device node must contain one 'port' child node for its digital output
-video port, in accordance with the video interface bindings defined in
-Documentation/devicetree/bindings/media/video-interfaces.txt.
-
-OV5640 can be connected to a MIPI CSI-2 bus or a parallel bus endpoint.
-
-Endpoint node required properties for CSI-2 connection are:
-- remote-endpoint: a phandle to the bus receiver's endpoint node.
-- clock-lanes: should be set to <0> (clock lane on hardware lane 0)
-- data-lanes: should be set to <1> or <1 2> (one or two CSI-2 lanes supported)
-
-Endpoint node required properties for parallel connection are:
-- remote-endpoint: a phandle to the bus receiver's endpoint node.
-- bus-width: shall be set to <8> for 8 bits parallel bus
-	     or <10> for 10 bits parallel bus
-- data-shift: shall be set to <2> for 8 bits parallel bus
-	      (lines 9:2 are used) or <0> for 10 bits parallel bus
-- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
-- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
-- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock
-	       signal.
-
-Examples:
-
-&i2c1 {
-	ov5640: camera@3c {
-		compatible = "ovti,ov5640";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ov5640>;
-		reg = <0x3c>;
-		clocks = <&clks IMX6QDL_CLK_CKO>;
-		clock-names = "xclk";
-		DOVDD-supply = <&vgen4_reg>; /* 1.8v */
-		AVDD-supply = <&vgen3_reg>;  /* 2.8v */
-		DVDD-supply = <&vgen2_reg>;  /* 1.5v */
-		powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
-		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
-		rotation = <180>;
-
-		port {
-			/* MIPI CSI-2 bus endpoint */
-			ov5640_to_mipi_csi2: endpoint {
-				remote-endpoint = <&mipi_csi2_from_ov5640>;
-				clock-lanes = <0>;
-				data-lanes = <1 2>;
-			};
-		};
-	};
-};
-
-&i2c1 {
-	ov5640: camera@3c {
-		compatible = "ovti,ov5640";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ov5640>;
-		reg = <0x3c>;
-		clocks = <&clk_ext_camera>;
-		clock-names = "xclk";
-
-		port {
-			/* Parallel bus endpoint */
-			ov5640_to_parallel: endpoint {
-				remote-endpoint = <&parallel_from_ov5640>;
-				bus-width = <8>;
-				data-shift = <2>; /* lines 9:2 are used */
-				hsync-active = <0>;
-				vsync-active = <0>;
-				pclk-sample = <1>;
-			};
-		};
-	};
-};
diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
new file mode 100644
index 000000000000..0283b1895a75
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
@@ -0,0 +1,154 @@ 
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov5640.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: OmniVision OV5640 Image Sensor Device Tree Bindings
+
+maintainers:
+  - Steve Longerbeam <slongerbeam@gmail.com>
+
+allOf:
+  - $ref: /schemas/media/video-interface-devices.yaml#
+
+properties:
+  compatible:
+    const: ovti,ov5640
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    description: XCLK Input Clock
+
+  clock-names:
+    const: xclk
+
+  AVDD-supply:
+    description: Analog voltage supply, 2.8 volts
+
+  DVDD-supply:
+    description: Digital core voltage supply, 1.5 volts
+
+  DOVDD-supply:
+    description: Digital I/O voltage supply, 1.8 volts
+
+  powerdown-gpios:
+    maxItems: 1
+    description: >
+      Reference to the GPIO connected to the powerdown pin, if any.
+
+  reset-gpios:
+    maxItems: 1
+    description: >
+      Reference to the GPIO connected to the reset pin, if any.
+
+  rotation:
+    enum: 
+      - 0
+      - 180
+
+  port:
+    description: Digital Output Port
+    $ref: /schemas/graph.yaml#/properties/port
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          clock-lanes:
+            const: 0
+
+          data-lanes:
+            minItems: 1
+            maxItems: 2
+            items:
+              enum: [1, 2]
+
+          bus-width:
+            enum: [8, 10]
+
+          data-shift:
+            enum: [0, 2]
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - AVDD-supply
+  - DVDD-supply
+  - DOVDD-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+      #include <dt-bindings/clock/imx6qdl-clock.h>
+      #include <dt-bindings/gpio/gpio.h>
+
+      i2c {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          camera@3c {
+              compatible = "ovti,ov5640";
+              pinctrl-names = "default";
+              pinctrl-0 = <&pinctrl_ov5640>;
+              reg = <0x3c>;
+              clocks = <&clks IMX6QDL_CLK_CKO>;
+              clock-names = "xclk";
+              DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+              AVDD-supply = <&vgen3_reg>;  /* 2.8v */
+              DVDD-supply = <&vgen2_reg>;  /* 1.5v */
+              powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+              reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+              rotation = <180>;
+
+              port {
+                  /* MIPI CSI-2 bus endpoint */
+                  ov5640_to_mipi_csi2: endpoint {
+                      remote-endpoint = <&mipi_csi2_from_ov5640>;
+                      clock-lanes = <0>;
+                      data-lanes = <1 2>;
+                  };
+              };
+          };
+      };
+
+  - |
+      i2c {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          camera@3c {
+              compatible = "ovti,ov5640";
+              pinctrl-names = "default";
+              pinctrl-0 = <&pinctrl_ov5640>;
+              reg = <0x3c>;
+              clocks = <&clk_ext_camera>;
+              clock-names = "xclk";
+              DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+              AVDD-supply = <&vgen3_reg>;  /* 2.8v */
+              DVDD-supply = <&vgen2_reg>;  /* 1.5v */
+
+              port {
+                  /* Parallel bus endpoint */
+                  ov5640_to_parallel: endpoint {
+                      remote-endpoint = <&parallel_from_ov5640>;
+                      bus-width = <8>;
+                      data-shift = <2>; /* lines 9:2 are used */
+                      hsync-active = <0>;
+                      vsync-active = <0>;
+                      pclk-sample = <1>;
+                  };
+              };
+          };
+      };
+
+...