diff mbox series

[v1] Revert "Bluetooth: core: Fix missing power_on work cancel on HCI close"

Message ID 20220614181706.26513-1-max.oss.09@gmail.com
State New
Headers show
Series [v1] Revert "Bluetooth: core: Fix missing power_on work cancel on HCI close" | expand

Commit Message

Max Krummenacher June 14, 2022, 6:17 p.m. UTC
From: Max Krummenacher <max.krummenacher@toradex.com>

This reverts commit ff7f2926114d3a50f5ffe461a9bce8d761748da5.

The commit ff7f2926114d ("Bluetooth: core: Fix missing power_on work
cancel on HCI close") introduced between v5.18 and v5.19-rc1 makes
going to suspend freeze. v5.19-rc2 is equally affected.

This has been seen on a Colibri iMX6ULL WB which has a Marvell 8997
based WiFi / Bluetooth module connected over SDIO.

With 'v5.18' or 'v5.19-rc1 with said commit reverted' a suspend/resume
cycle looks as follows and the device is functional after the resume:

root@imx6ull:~# rfkill
ID TYPE      DEVICE    SOFT      HARD
 0 bluetooth hci0   blocked unblocked
 1 wlan      phy0   blocked unblocked
root@imx6ull:~# echo enabled > /sys/class/tty/ttymxc0/power/wakeup
root@imx6ull:~# date;echo mem > /sys/power/state;date
Tue Jun 14 14:43:03 UTC 2022
[ 6393.464497] PM: suspend entry (deep)
[ 6393.529398] Filesystems sync: 0.064 seconds
[ 6393.594006] Freezing user space processes ... (elapsed 0.015 seconds) done.
[ 6393.610266] OOM killer disabled.
[ 6393.610285] Freezing remaining freezable tasks ... (elapsed 0.013 seconds) done.
[ 6393.623727] printk: Suspending console(s) (use no_console_suspend to debug)

~~ suspended until console initiates the resume

[ 6394.023552] fec 20b4000.ethernet eth0: Link is Down
[ 6394.049902] PM: suspend devices took 0.300 seconds
[ 6394.091654] Disabling non-boot CPUs ...
[ 6394.565896] PM: resume devices took 0.440 seconds
[ 6394.681350] OOM killer enabled.
[ 6394.681369] Restarting tasks ... done.
[ 6394.741157] random: crng reseeded on system resumption
[ 6394.813135] PM: suspend exit
Tue Jun 14 14:43:11 UTC 2022
[ 6396.403873] fec 20b4000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[ 6396.404347] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
root@imx6ull:~#

With 'v5.19-rc1' suspend freezes in the suspend phase, i.e. power
consumption is not lowered and no wakeup source initiates a wakup.

root@imx6ull:~# rfkill
ID TYPE      DEVICE    SOFT      HARD
 0 bluetooth hci0   blocked unblocked
 1 wlan      phy0   blocked unblocked
root@imx6ull:~# echo enabled > /sys/class/tty/ttymxc0/power/wakeup
root@imx6ull:~# date;echo mem > /sys/power/state;date
Tue Jun 14 12:40:38 UTC 2022
[  122.476333] PM: suspend entry (deep)
[  122.556012] Filesystems sync: 0.079 seconds

~~ no further kernel output

If one first unbinds the bluetooth device driver, suspend / resume works
as expected also with 'v5.19-rc1':

root@imx6ull:~# echo mmc1:0001:2 > /sys/bus/sdio/drivers/btmrvl_sdio/unbind
root@imx6ull:~# rfkill
ID TYPE DEVICE    SOFT      HARD
 1 wlan phy0   blocked unblocked
root@imx6ull:~# echo enabled > /sys/class/tty/ttymxc0/power/wakeup
root@imx6ull:~# date;echo mem > /sys/power/state;date
Tue Jun 14 14:59:26 UTC 2022
[  123.530310] PM: suspend entry (deep)
[  123.595432] Filesystems sync: 0.064 seconds
[  123.672478] Freezing user space processes ... (elapsed 0.028 seconds) done.
[  123.701848] OOM killer disabled.
[  123.701869] Freezing remaining freezable tasks ... (elapsed 0.007 seconds) done.
[  123.709993] printk: Suspending console(s) (use no_console_suspend to debug)
[  124.097772] fec 20b4000.ethernet eth0: Link is Down
[  124.124795] PM: suspend devices took 0.280 seconds
[  124.165893] Disabling non-boot CPUs ...
[  124.632959] PM: resume devices took 0.430 seconds
[  124.750164] OOM killer enabled.
[  124.750187] Restarting tasks ... done.
[  124.827899] random: crng reseeded on system resumption
[  124.923183] PM: suspend exit
Tue Jun 14 14:59:31 UTC 2022
[  127.520321] fec 20b4000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[  127.520514] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
root@imx6ull:~#

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>

---

 net/bluetooth/hci_core.c | 2 ++
 net/bluetooth/hci_sync.c | 1 -
 2 files changed, 2 insertions(+), 1 deletion(-)

Comments

Jakub Kicinski June 23, 2022, 7:51 p.m. UTC | #1
On Tue, 21 Jun 2022 13:55:14 +0200 Francesco Dolcini wrote:
> Marcel, Vasyl,
> any comment on this?

+1 is there an ETA on the fix getting into net?

> On Tue, Jun 14, 2022 at 08:17:06PM +0200, Max Krummenacher wrote:
> > From: Max Krummenacher <max.krummenacher@toradex.com>
> > 
> > This reverts commit ff7f2926114d3a50f5ffe461a9bce8d761748da5.
> > 
> > The commit ff7f2926114d ("Bluetooth: core: Fix missing power_on work
> > cancel on HCI close") introduced between v5.18 and v5.19-rc1 makes
> > going to suspend freeze. v5.19-rc2 is equally affected.
> > 
> > This has been seen on a Colibri iMX6ULL WB which has a Marvell 8997
> > based WiFi / Bluetooth module connected over SDIO.
> > 
> > With 'v5.18' or 'v5.19-rc1 with said commit reverted' a suspend/resume
> > cycle looks as follows and the device is functional after the resume:
Mateusz Jończyk July 4, 2022, 7:56 p.m. UTC | #2
W dniu 14.06.2022 o 20:17, Max Krummenacher pisze:
> From: Max Krummenacher <max.krummenacher@toradex.com>
>
> This reverts commit ff7f2926114d3a50f5ffe461a9bce8d761748da5.
>
> The commit ff7f2926114d ("Bluetooth: core: Fix missing power_on work
> cancel on HCI close") introduced between v5.18 and v5.19-rc1 makes
> going to suspend freeze. v5.19-rc2 is equally affected.
>
> This has been seen on a Colibri iMX6ULL WB which has a Marvell 8997
> based WiFi / Bluetooth module connected over SDIO.
> [...]

Hello,

commit ff7f2926114d ("Bluetooth: core: Fix missing power_on work cancel on HCI close")

causes problems also on my laptop (HP 17-by0001nw with a Realtek Bluetooth adapter).

I have Bluetooth disabled by default on startup (via systemd-rfkill.service ) and
vanilla kernel 5.19.0-rc5 fails to suspend (the screen turns black, but I am then able to
touch a trackpad and log in). Reverting that commit on top of 5.19.0-rc5 fixes the issue.

On bare 5.19.0-rc5, after startup, the kworker/u9:0+hci0 process hangs indefinitely
with this stacktrace (obtained through "cat /proc/163/stack" )

        [<0>] __flush_work+0x143/0x220
        [<0>] __cancel_work_timer+0x122/0x1a0
        [<0>] cancel_work_sync+0x10/0x20
        [<0>] hci_dev_close_sync+0x2a/0x550 [bluetooth]
        [<0>] hci_dev_do_close+0x2a/0x60 [bluetooth]
        [<0>] hci_power_on+0x91/0x200 [bluetooth]
        [<0>] process_one_work+0x21c/0x3c0
        [<0>] worker_thread+0x4a/0x3a0
        [<0>] kthread+0xcf/0xf0
        [<0>] ret_from_fork+0x22/0x30

It appears that the hci_power_on() function calls hci_dev_do_close() in this block:

    if (hci_dev_test_flag(hdev, HCI_RFKILLED) ||
         /* [...] */ ) {
        hci_dev_clear_flag(hdev, HCI_AUTO_OFF);
        hci_dev_do_close(hdev);
    } else /* [...] */

which then calls hci_dev_close_sync(). With the problematic commit, that function
calls

       cancel_work_sync(&hdev->power_on)

which tries to cancel the execution of the hci_power_on() function's itself, which leads to a deadlock.

When trying to suspend, the "/lib/systemd/systemd-sleep suspend" process hangs on

        [<0>] hci_suspend_dev+0x87/0xf0 [bluetooth]
        [<0>] hci_suspend_notifier+0x38/0x80 [bluetooth]
        [<0>] notifier_call_chain_robust+0x5e/0xc0
        [<0>] blocking_notifier_call_chain_robust+0x42/0x60
        [<0>] pm_notifier_call_chain_robust+0x1d/0x40
        [<0>] pm_suspend+0x116/0x5a0
        [<0>] state_store+0x82/0xe0
        [<0>] kobj_attr_store+0x12/0x20
        [<0>] sysfs_kf_write+0x3e/0x50
        [<0>] kernfs_fop_write_iter+0x138/0x1c0
        [<0>] new_sync_write+0x104/0x180
        [<0>] vfs_write+0x1d7/0x260
        [<0>] ksys_write+0x67/0xe0
        [<0>] __x64_sys_write+0x1a/0x20
        [<0>] do_syscall_64+0x3b/0x90
        [<0>] entry_SYSCALL_64_after_hwframe+0x46/0xb0

My device is:

Bus 001 Device 005: ID 0bda:b00b Realtek Semiconductor Corp. Bluetooth Radio

So probably the
commit ff7f2926114d ("Bluetooth: core: Fix missing power_on work cancel on HCI close")
should be reverted or corrected.

Greetings,

Mateusz Jończyk

> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
> ---
>
>  net/bluetooth/hci_core.c | 2 ++
>  net/bluetooth/hci_sync.c | 1 -
>  2 files changed, 2 insertions(+), 1 deletion(-)
>
> diff --git a/net/bluetooth/hci_core.c b/net/bluetooth/hci_core.c
> index 59a5c1341c26..19df3905c5f8 100644
> --- a/net/bluetooth/hci_core.c
> +++ b/net/bluetooth/hci_core.c
> @@ -2675,6 +2675,8 @@ void hci_unregister_dev(struct hci_dev *hdev)
>  	list_del(&hdev->list);
>  	write_unlock(&hci_dev_list_lock);
>  
> +	cancel_work_sync(&hdev->power_on);
> +
>  	hci_cmd_sync_clear(hdev);
>  
>  	if (!test_bit(HCI_QUIRK_NO_SUSPEND_NOTIFIER, &hdev->quirks))
> diff --git a/net/bluetooth/hci_sync.c b/net/bluetooth/hci_sync.c
> index 286d6767f017..1739e8cb3291 100644
> --- a/net/bluetooth/hci_sync.c
> +++ b/net/bluetooth/hci_sync.c
> @@ -4088,7 +4088,6 @@ int hci_dev_close_sync(struct hci_dev *hdev)
>  
>  	bt_dev_dbg(hdev, "");
>  
> -	cancel_work_sync(&hdev->power_on);
>  	cancel_delayed_work(&hdev->power_off);
>  	cancel_delayed_work(&hdev->ncmd_timer);
>
Max Krummenacher July 5, 2022, 2:09 p.m. UTC | #3
On Mon, Jul 4, 2022 at 9:57 PM Mateusz Jończyk <mat.jonczyk@o2.pl> wrote:
>
> W dniu 14.06.2022 o 20:17, Max Krummenacher pisze:
> > From: Max Krummenacher <max.krummenacher@toradex.com>
> >
> > This reverts commit ff7f2926114d3a50f5ffe461a9bce8d761748da5.
> >
> > The commit ff7f2926114d ("Bluetooth: core: Fix missing power_on work
> > cancel on HCI close") introduced between v5.18 and v5.19-rc1 makes
> > going to suspend freeze. v5.19-rc2 is equally affected.

The following follow up commit fixes the issue for me without the revert.
https://lore.kernel.org/all/20220705125931.3601-1-vasyl.vavrychuk@opensynergy.com/

Thanks
Max
Max Krummenacher July 5, 2022, 2:12 p.m. UTC | #4
On Tue, Jul 5, 2022 at 3:00 PM Vasyl Vavrychuk
<vasyl.vavrychuk@opensynergy.com> wrote:
>
> `cancel_work_sync(&hdev->power_on)` was moved to hci_dev_close_sync in
> commit [1] to ensure that power_on work is canceled after HCI interface
> down.
>
> But, in certain cases power_on work function may call hci_dev_close_sync
> itself: hci_power_on -> hci_dev_do_close -> hci_dev_close_sync ->
> cancel_work_sync(&hdev->power_on), causing deadlock. In particular, this
> happens when device is rfkilled on boot. To avoid deadlock, move
> power_on work canceling out of hci_dev_do_close/hci_dev_close_sync.
>
> Deadlock introduced by commit [1] was reported in [2,3] as broken
> suspend. Suspend did not work because `hdev->req_lock` held as result of
> `power_on` work deadlock. In fact, other BT features were not working.
> It was not observed when testing [1] since it was verified without
> rfkill in place.
>
> NOTE: It is not needed to cancel power_on work from other places where
> hci_dev_do_close/hci_dev_close_sync is called in case:
> * Requests were serialized due to `hdev->req_workqueue`. The power_on
> work is first in that workqueue.
> * hci_rfkill_set_block which won't close device anyway until HCI_SETUP
> is on.
> * hci_sock_release which runs after hci_sock_bind which ensures
> HCI_SETUP was cleared.
>
> As result, behaviour is the same as in pre-dd06ed7 commit, except
> power_on work cancel added to hci_dev_close.
>
> [1]: commit dd06ed7ad057 ("Bluetooth: core: Fix missing power_on work cancel on HCI close")
> [2]: https://lore.kernel.org/lkml/20220614181706.26513-1-max.oss.09@gmail.com/
> [2]: https://lore.kernel.org/lkml/1236061d-95dd-c3ad-a38f-2dae7aae51ef@o2.pl/
>
> Fixes: commit dd06ed7ad057 ("Bluetooth: core: Fix missing power_on work cancel on HCI close")
> Signed-off-by: Vasyl Vavrychuk <vasyl.vavrychuk@opensynergy.com>
> Reported-by: Max Krummenacher <max.krummenacher@toradex.com>
> Reported-by: Mateusz Jonczyk <mat.jonczyk@o2.pl>
> ---
>  net/bluetooth/hci_core.c | 3 +++
>  net/bluetooth/hci_sync.c | 1 -
>  2 files changed, 3 insertions(+), 1 deletion(-)
>
> diff --git a/net/bluetooth/hci_core.c b/net/bluetooth/hci_core.c
> index 59a5c1341c26..a0f99baafd35 100644
> --- a/net/bluetooth/hci_core.c
> +++ b/net/bluetooth/hci_core.c
> @@ -571,6 +571,7 @@ int hci_dev_close(__u16 dev)
>                 goto done;
>         }
>
> +       cancel_work_sync(&hdev->power_on);
>         if (hci_dev_test_and_clear_flag(hdev, HCI_AUTO_OFF))
>                 cancel_delayed_work(&hdev->power_off);
>
> @@ -2675,6 +2676,8 @@ void hci_unregister_dev(struct hci_dev *hdev)
>         list_del(&hdev->list);
>         write_unlock(&hci_dev_list_lock);
>
> +       cancel_work_sync(&hdev->power_on);
> +
>         hci_cmd_sync_clear(hdev);
>
>         if (!test_bit(HCI_QUIRK_NO_SUSPEND_NOTIFIER, &hdev->quirks))
> diff --git a/net/bluetooth/hci_sync.c b/net/bluetooth/hci_sync.c
> index 286d6767f017..1739e8cb3291 100644
> --- a/net/bluetooth/hci_sync.c
> +++ b/net/bluetooth/hci_sync.c
> @@ -4088,7 +4088,6 @@ int hci_dev_close_sync(struct hci_dev *hdev)
>
>         bt_dev_dbg(hdev, "");
>
> -       cancel_work_sync(&hdev->power_on);
>         cancel_delayed_work(&hdev->power_off);
>         cancel_delayed_work(&hdev->ncmd_timer);
>
> --
> 2.30.2
>

This fixes the issue I described in [1]. I.e. The kernel no longer
freezes while going to suspend.
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>

Thanks!
Max
Francesco Dolcini July 5, 2022, 3:14 p.m. UTC | #5
Hello Vasyl,

On Tue, Jul 05, 2022 at 03:59:31PM +0300, Vasyl Vavrychuk wrote:
> Fixes: commit dd06ed7ad057 ("Bluetooth: core: Fix missing power_on work cancel on HCI close")

This fixes tag is broken, dd06ed7ad057 does not exist on
torvalds/master, and the `commit` word should be removed.

Should be:

Fixes: ff7f2926114d ("Bluetooth: core: Fix missing power_on work cancel on HCI close")


Francesco
Luiz Augusto von Dentz July 5, 2022, 5:26 p.m. UTC | #6
Hi,

On Tue, Jul 5, 2022 at 8:14 AM Francesco Dolcini
<francesco.dolcini@toradex.com> wrote:
>
> Hello Vasyl,
>
> On Tue, Jul 05, 2022 at 03:59:31PM +0300, Vasyl Vavrychuk wrote:
> > Fixes: commit dd06ed7ad057 ("Bluetooth: core: Fix missing power_on work cancel on HCI close")
>
> This fixes tag is broken, dd06ed7ad057 does not exist on
> torvalds/master, and the `commit` word should be removed.
>
> Should be:
>
> Fixes: ff7f2926114d ("Bluetooth: core: Fix missing power_on work cancel on HCI close")

Ive rebased the patch on top of bluetooth-next and fixed the hash,
lets see if passes CI I might just go ahead and push it.
Jakub Kicinski July 5, 2022, 6:38 p.m. UTC | #7
On Tue, 5 Jul 2022 10:26:08 -0700 Luiz Augusto von Dentz wrote:
> On Tue, Jul 5, 2022 at 8:14 AM Francesco Dolcini
> <francesco.dolcini@toradex.com> wrote:
> >
> > Hello Vasyl,
> >
> > On Tue, Jul 05, 2022 at 03:59:31PM +0300, Vasyl Vavrychuk wrote:  
> > > Fixes: commit dd06ed7ad057 ("Bluetooth: core: Fix missing power_on work cancel on HCI close")  
> >
> > This fixes tag is broken, dd06ed7ad057 does not exist on
> > torvalds/master, and the `commit` word should be removed.
> >
> > Should be:
> >
> > Fixes: ff7f2926114d ("Bluetooth: core: Fix missing power_on work cancel on HCI close")  
> 
> Ive rebased the patch on top of bluetooth-next and fixed the hash,
> lets see if passes CI I might just go ahead and push it.

Thanks for pushing it along, the final version can got thru bluetooth ->
-> net and into 5.19, right?
Mateusz Jończyk July 5, 2022, 6:38 p.m. UTC | #8
W dniu 5.07.2022 o 14:59, Vasyl Vavrychuk pisze:
> `cancel_work_sync(&hdev->power_on)` was moved to hci_dev_close_sync in
> commit [1] to ensure that power_on work is canceled after HCI interface
> down.
>
> But, in certain cases power_on work function may call hci_dev_close_sync
> itself: hci_power_on -> hci_dev_do_close -> hci_dev_close_sync ->
> cancel_work_sync(&hdev->power_on), causing deadlock. In particular, this
> happens when device is rfkilled on boot. To avoid deadlock, move
> power_on work canceling out of hci_dev_do_close/hci_dev_close_sync.
>
> Deadlock introduced by commit [1] was reported in [2,3] as broken
> suspend. Suspend did not work because `hdev->req_lock` held as result of
> `power_on` work deadlock. In fact, other BT features were not working.
> It was not observed when testing [1] since it was verified without
> rfkill in place.
>
> NOTE: It is not needed to cancel power_on work from other places where
> hci_dev_do_close/hci_dev_close_sync is called in case:
> * Requests were serialized due to `hdev->req_workqueue`. The power_on
> work is first in that workqueue.
> * hci_rfkill_set_block which won't close device anyway until HCI_SETUP
> is on.
> * hci_sock_release which runs after hci_sock_bind which ensures
> HCI_SETUP was cleared.
>
> As result, behaviour is the same as in pre-dd06ed7 commit, except
> power_on work cancel added to hci_dev_close.
>
> [1]: commit dd06ed7ad057 ("Bluetooth: core: Fix missing power_on work cancel on HCI close")
> [2]: https://lore.kernel.org/lkml/20220614181706.26513-1-max.oss.09@gmail.com/
> [2]: https://lore.kernel.org/lkml/1236061d-95dd-c3ad-a38f-2dae7aae51ef@o2.pl/
>
> Fixes: commit dd06ed7ad057 ("Bluetooth: core: Fix missing power_on work cancel on HCI close")
> Signed-off-by: Vasyl Vavrychuk <vasyl.vavrychuk@opensynergy.com>
> Reported-by: Max Krummenacher <max.krummenacher@toradex.com>
> Reported-by: Mateusz Jonczyk <mat.jonczyk@o2.pl>

Works well: suspend (with bluetooth on and also off), hibernation, sending files, rfkill.

Thank you.

Reported-and-tested-by: Mateusz Jończyk <mat.jonczyk@o2.pl>

Greetings,

Mateusz Jończyk
Luiz Augusto von Dentz July 5, 2022, 7 p.m. UTC | #9
Hi Jakub,

On Tue, Jul 5, 2022 at 11:38 AM Jakub Kicinski <kuba@kernel.org> wrote:
>
> On Tue, 5 Jul 2022 10:26:08 -0700 Luiz Augusto von Dentz wrote:
> > On Tue, Jul 5, 2022 at 8:14 AM Francesco Dolcini
> > <francesco.dolcini@toradex.com> wrote:
> > >
> > > Hello Vasyl,
> > >
> > > On Tue, Jul 05, 2022 at 03:59:31PM +0300, Vasyl Vavrychuk wrote:
> > > > Fixes: commit dd06ed7ad057 ("Bluetooth: core: Fix missing power_on work cancel on HCI close")
> > >
> > > This fixes tag is broken, dd06ed7ad057 does not exist on
> > > torvalds/master, and the `commit` word should be removed.
> > >
> > > Should be:
> > >
> > > Fixes: ff7f2926114d ("Bluetooth: core: Fix missing power_on work cancel on HCI close")
> >
> > Ive rebased the patch on top of bluetooth-next and fixed the hash,
> > lets see if passes CI I might just go ahead and push it.
>
> Thanks for pushing it along, the final version can got thru bluetooth ->
> -> net and into 5.19, right?

Yep, I will send the pull request in a moment.
Jakub Kicinski July 5, 2022, 7:13 p.m. UTC | #10
On Tue, 5 Jul 2022 12:00:43 -0700 Luiz Augusto von Dentz wrote:
> > > Ive rebased the patch on top of bluetooth-next and fixed the hash,
> > > lets see if passes CI I might just go ahead and push it.  
> >
> > Thanks for pushing it along, the final version can got thru bluetooth ->  
> > -> net and into 5.19, right?  
> 
> Yep, I will send the pull request in a moment.

Perfect, thank you!!
diff mbox series

Patch

diff --git a/net/bluetooth/hci_core.c b/net/bluetooth/hci_core.c
index 59a5c1341c26..19df3905c5f8 100644
--- a/net/bluetooth/hci_core.c
+++ b/net/bluetooth/hci_core.c
@@ -2675,6 +2675,8 @@  void hci_unregister_dev(struct hci_dev *hdev)
 	list_del(&hdev->list);
 	write_unlock(&hci_dev_list_lock);
 
+	cancel_work_sync(&hdev->power_on);
+
 	hci_cmd_sync_clear(hdev);
 
 	if (!test_bit(HCI_QUIRK_NO_SUSPEND_NOTIFIER, &hdev->quirks))
diff --git a/net/bluetooth/hci_sync.c b/net/bluetooth/hci_sync.c
index 286d6767f017..1739e8cb3291 100644
--- a/net/bluetooth/hci_sync.c
+++ b/net/bluetooth/hci_sync.c
@@ -4088,7 +4088,6 @@  int hci_dev_close_sync(struct hci_dev *hdev)
 
 	bt_dev_dbg(hdev, "");
 
-	cancel_work_sync(&hdev->power_on);
 	cancel_delayed_work(&hdev->power_off);
 	cancel_delayed_work(&hdev->ncmd_timer);