@@ -15031,7 +15031,6 @@ Q: http://patchwork.kernel.org/project/linux-omap/list/
T: git git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap.git
F: arch/arm/configs/omap1_defconfig
F: arch/arm/mach-omap1/
-F: arch/arm/plat-omap/
F: drivers/i2c/busses/i2c-omap.c
F: include/linux/platform_data/ams-delta-fiq.h
F: include/linux/platform_data/i2c-omap.h
@@ -15046,7 +15045,6 @@ Q: http://patchwork.kernel.org/project/linux-omap/list/
T: git git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap.git
F: arch/arm/configs/omap2plus_defconfig
F: arch/arm/mach-omap2/
-F: arch/arm/plat-omap/
F: drivers/bus/ti-sysc.c
F: drivers/i2c/busses/i2c-omap.c
F: drivers/irqchip/irq-omap-intc.c
@@ -760,30 +760,6 @@ choice
depends on ARCH_OMAP2PLUS
select DEBUG_UART_8250
- config DEBUG_OMAP7XXUART1
- bool "Kernel low-level debugging via OMAP730 UART1"
- depends on ARCH_OMAP730
- select DEBUG_UART_8250
- help
- Say Y here if you want kernel low-level debugging support
- on OMAP730 based platforms on the UART1.
-
- config DEBUG_OMAP7XXUART2
- bool "Kernel low-level debugging via OMAP730 UART2"
- depends on ARCH_OMAP730
- select DEBUG_UART_8250
- help
- Say Y here if you want kernel low-level debugging support
- on OMAP730 based platforms on the UART2.
-
- config DEBUG_OMAP7XXUART3
- bool "Kernel low-level debugging via OMAP730 UART3"
- depends on ARCH_OMAP730
- select DEBUG_UART_8250
- help
- Say Y here if you want kernel low-level debugging support
- on OMAP730 based platforms on the UART3.
-
config DEBUG_TI81XXUART1
bool "Kernel low-level debugging messages via TI81XX UART1 (ti8148evm)"
depends on ARCH_OMAP2PLUS
@@ -1728,9 +1704,9 @@ config DEBUG_UART_PHYS
default 0xffe40000 if DEBUG_RCAR_GEN1_SCIF0
default 0xffe42000 if DEBUG_RCAR_GEN1_SCIF2
default 0xfff36000 if DEBUG_HIGHBANK_UART
- default 0xfffb0000 if DEBUG_OMAP1UART1 || DEBUG_OMAP7XXUART1
- default 0xfffb0800 if DEBUG_OMAP1UART2 || DEBUG_OMAP7XXUART2
- default 0xfffb9800 if DEBUG_OMAP1UART3 || DEBUG_OMAP7XXUART3
+ default 0xfffb0000 if DEBUG_OMAP1UART1
+ default 0xfffb0800 if DEBUG_OMAP1UART2
+ default 0xfffb9800 if DEBUG_OMAP1UART3
default 0xfffe8600 if DEBUG_BCM63XX_UART
default 0xffffee00 if DEBUG_AT91_SAM9263_DBGU
default 0xfffff200 if DEBUG_AT91_RM9200_DBGU
@@ -1847,9 +1823,9 @@ config DEBUG_UART_VIRT
default 0xfec00000 if ARCH_IXP4XX && !CPU_BIG_ENDIAN
default 0xfec00003 if ARCH_IXP4XX && CPU_BIG_ENDIAN
default 0xfef36000 if DEBUG_HIGHBANK_UART
- default 0xff0b0000 if DEBUG_OMAP1UART1 || DEBUG_OMAP7XXUART1
- default 0xff0b0800 if DEBUG_OMAP1UART2 || DEBUG_OMAP7XXUART2
- default 0xff0b9800 if DEBUG_OMAP1UART3 || DEBUG_OMAP7XXUART3
+ default 0xff0b0000 if DEBUG_OMAP1UART1
+ default 0xff0b0800 if DEBUG_OMAP1UART2
+ default 0xff0b9800 if DEBUG_OMAP1UART3
default 0xffd01000 if DEBUG_HIP01_UART
default DEBUG_UART_PHYS if !MMU
depends on DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \
@@ -20,8 +20,6 @@ CONFIG_ARCH_OMAP=y
CONFIG_ARCH_OMAP1=y
CONFIG_OMAP_32K_TIMER=y
CONFIG_OMAP_DM_TIMER=y
-CONFIG_ARCH_OMAP730=y
-CONFIG_ARCH_OMAP850=y
CONFIG_ARCH_OMAP16XX=y
# CONFIG_OMAP_MUX is not set
CONFIG_OMAP_RESET_CLOCKS=y
@@ -18,19 +18,6 @@ menu "TI OMAP1 specific features"
comment "OMAP Core Type"
-config ARCH_OMAP730
- depends on ARCH_MULTI_V5
- bool "OMAP730 Based System"
- select ARCH_OMAP_OTG
- select CPU_ARM926T
- select OMAP_MPU_TIMER
-
-config ARCH_OMAP850
- depends on ARCH_MULTI_V5
- bool "OMAP850 Based System"
- select ARCH_OMAP_OTG
- select CPU_ARM926T
-
config ARCH_OMAP15XX
depends on ARCH_MULTI_V4T
default y
@@ -47,7 +34,7 @@ config ARCH_OMAP16XX
config ARCH_OMAP1_ANY
select ARCH_OMAP
- def_bool ARCH_OMAP730 || ARCH_OMAP850 || ARCH_OMAP15XX || ARCH_OMAP16XX
+ def_bool ARCH_OMAP15XX || ARCH_OMAP16XX
config ARCH_OMAP
bool
@@ -129,37 +116,6 @@ config ARCH_OMAP_OTG
comment "OMAP Board Type"
-config MACH_OMAP_INNOVATOR
- bool "TI Innovator"
- depends on ARCH_OMAP15XX || ARCH_OMAP16XX
- depends on UNUSED_BOARD_FILES
- help
- TI OMAP 1510 or 1610 Innovator board support. Say Y here if you
- have such a board.
-
-config MACH_OMAP_H2
- bool "TI H2 Support"
- depends on ARCH_OMAP16XX
- depends on UNUSED_BOARD_FILES
- help
- TI OMAP 1610/1611B H2 board support. Say Y here if you have such
- a board.
-
-config MACH_OMAP_H3
- bool "TI H3 Support"
- depends on ARCH_OMAP16XX
- depends on UNUSED_BOARD_FILES
- help
- TI OMAP 1710 H3 board support. Say Y here if you have such
- a board.
-
-config MACH_HERALD
- bool "HTC Herald"
- depends on ARCH_OMAP850
- depends on UNUSED_BOARD_FILES
- help
- HTC Herald smartphone support (AKA T-Mobile Wing, ...)
-
config MACH_OMAP_OSK
bool "TI OSK Support"
depends on ARCH_OMAP16XX
@@ -170,28 +126,11 @@ config MACH_OMAP_OSK
config OMAP_OSK_MISTRAL
bool "Mistral QVGA board Support"
depends on MACH_OMAP_OSK
- depends on UNUSED_BOARD_FILES
help
The OSK supports an optional add-on board with a Quarter-VGA
touchscreen, PDA-ish buttons, a resume button, bicolor LED,
and camera connector. Say Y here if you have this board.
-config MACH_OMAP_PERSEUS2
- bool "TI Perseus2"
- depends on ARCH_OMAP730
- depends on UNUSED_BOARD_FILES
- help
- Support for TI OMAP 730 Perseus2 board. Say Y here if you have such
- a board.
-
-config MACH_OMAP_FSAMPLE
- bool "TI F-Sample"
- depends on ARCH_OMAP730
- depends on UNUSED_BOARD_FILES
- help
- Support for TI OMAP 850 F-Sample board. Say Y here if you have such
- a board.
-
config MACH_OMAP_PALMTE
bool "Palm Tungsten E"
depends on ARCH_OMAP15XX
@@ -201,26 +140,6 @@ config MACH_OMAP_PALMTE
http://palmtelinux.sourceforge.net/ for more information.
Say Y here if you have this PDA model, say N otherwise.
-config MACH_OMAP_PALMZ71
- bool "Palm Zire71"
- depends on ARCH_OMAP15XX
- depends on UNUSED_BOARD_FILES
- help
- Support for the Palm Zire71 PDA. To boot the kernel,
- you'll need a PalmOS compatible bootloader; check out
- http://hackndev.com/palm/z71 for more information.
- Say Y here if you have such a PDA, say N otherwise.
-
-config MACH_OMAP_PALMTT
- bool "Palm Tungsten|T"
- depends on ARCH_OMAP15XX
- depends on UNUSED_BOARD_FILES
- help
- Support for the Palm Tungsten|T PDA. To boot the kernel, you'll
- need a PalmOS compatible bootloader (Garux); check out
- http://garux.sourceforge.net/ for more information.
- Say Y here if you have this PDA model, say N otherwise.
-
config MACH_SX1
bool "Siemens SX1"
depends on ARCH_OMAP15XX
@@ -252,16 +171,6 @@ config MACH_AMS_DELTA
Support for the Amstrad E3 (codename Delta) videophone. Say Y here
if you have such a device.
-config MACH_OMAP_GENERIC
- bool "Generic OMAP board"
- depends on ARCH_OMAP15XX || ARCH_OMAP16XX
- depends on UNUSED_BOARD_FILES
- help
- Support for generic OMAP-1510, 1610 or 1710 board with
- no FPGA. Can be used as template for porting Linux to
- custom OMAP boards. Say Y here if you have a custom
- board.
-
endmenu
endif
@@ -31,32 +31,14 @@ usb-fs-$(CONFIG_USB_SUPPORT) := usb.o
obj-y += $(usb-fs-m) $(usb-fs-y)
# Specific board support
-obj-$(CONFIG_MACH_OMAP_H2) += board-h2.o board-h2-mmc.o \
- board-nand.o
-obj-$(CONFIG_MACH_OMAP_INNOVATOR) += board-innovator.o
-obj-$(CONFIG_MACH_OMAP_GENERIC) += board-generic.o
-obj-$(CONFIG_MACH_OMAP_PERSEUS2) += board-perseus2.o board-nand.o
-obj-$(CONFIG_MACH_OMAP_FSAMPLE) += board-fsample.o board-nand.o
obj-$(CONFIG_MACH_OMAP_OSK) += board-osk.o
-obj-$(CONFIG_MACH_OMAP_H3) += board-h3.o board-h3-mmc.o \
- board-nand.o
obj-$(CONFIG_MACH_OMAP_PALMTE) += board-palmte.o
-obj-$(CONFIG_MACH_OMAP_PALMZ71) += board-palmz71.o
-obj-$(CONFIG_MACH_OMAP_PALMTT) += board-palmtt.o
obj-$(CONFIG_MACH_NOKIA770) += board-nokia770.o
obj-$(CONFIG_MACH_AMS_DELTA) += board-ams-delta.o ams-delta-fiq.o \
ams-delta-fiq-handler.o
obj-$(CONFIG_MACH_SX1) += board-sx1.o board-sx1-mmc.o
-obj-$(CONFIG_MACH_HERALD) += board-htcherald.o
-
-ifeq ($(CONFIG_ARCH_OMAP15XX),y)
-# Innovator-1510 FPGA
-obj-$(CONFIG_MACH_OMAP_INNOVATOR) += fpga.o
-endif
# GPIO
-obj-$(CONFIG_ARCH_OMAP730) += gpio7xx.o
-obj-$(CONFIG_ARCH_OMAP850) += gpio7xx.o
obj-$(CONFIG_ARCH_OMAP15XX) += gpio15xx.o
obj-$(CONFIG_ARCH_OMAP16XX) += gpio16xx.o
deleted file mode 100644
@@ -1,366 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-omap1/board-fsample.c
- *
- * Modified from board-perseus2.c
- *
- * Original OMAP730 support by Jean Pihet <j-pihet@ti.com>
- * Updated for 2.6 by Kevin Hilman <kjh@hilman.org>
- */
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/platnand.h>
-#include <linux/mtd/physmap.h>
-#include <linux/input.h>
-#include <linux/smc91x.h>
-#include <linux/omapfb.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <linux/soc/ti/omap1-io.h>
-#include <linux/platform_data/keypad-omap.h>
-#include "tc.h"
-
-#include "mux.h"
-#include "flash.h"
-#include "hardware.h"
-#include "iomap.h"
-#include "common.h"
-#include "fpga.h"
-
-/* fsample is pretty close to p2-sample */
-
-#define fsample_cpld_read(reg) __raw_readb(reg)
-#define fsample_cpld_write(val, reg) __raw_writeb(val, reg)
-
-#define FSAMPLE_CPLD_BASE 0xE8100000
-#define FSAMPLE_CPLD_SIZE SZ_4K
-#define FSAMPLE_CPLD_START 0x05080000
-
-#define FSAMPLE_CPLD_REG_A (FSAMPLE_CPLD_BASE + 0x00)
-#define FSAMPLE_CPLD_SWITCH (FSAMPLE_CPLD_BASE + 0x02)
-#define FSAMPLE_CPLD_UART (FSAMPLE_CPLD_BASE + 0x02)
-#define FSAMPLE_CPLD_REG_B (FSAMPLE_CPLD_BASE + 0x04)
-#define FSAMPLE_CPLD_VERSION (FSAMPLE_CPLD_BASE + 0x06)
-#define FSAMPLE_CPLD_SET_CLR (FSAMPLE_CPLD_BASE + 0x06)
-
-#define FSAMPLE_CPLD_BIT_BT_RESET 0
-#define FSAMPLE_CPLD_BIT_LCD_RESET 1
-#define FSAMPLE_CPLD_BIT_CAM_PWDN 2
-#define FSAMPLE_CPLD_BIT_CHARGER_ENABLE 3
-#define FSAMPLE_CPLD_BIT_SD_MMC_EN 4
-#define FSAMPLE_CPLD_BIT_aGPS_PWREN 5
-#define FSAMPLE_CPLD_BIT_BACKLIGHT 6
-#define FSAMPLE_CPLD_BIT_aGPS_EN_RESET 7
-#define FSAMPLE_CPLD_BIT_aGPS_SLEEPx_N 8
-#define FSAMPLE_CPLD_BIT_OTG_RESET 9
-
-#define fsample_cpld_set(bit) \
- fsample_cpld_write((((bit) & 15) << 4) | 0x0f, FSAMPLE_CPLD_SET_CLR)
-
-#define fsample_cpld_clear(bit) \
- fsample_cpld_write(0xf0 | ((bit) & 15), FSAMPLE_CPLD_SET_CLR)
-
-static const unsigned int fsample_keymap[] = {
- KEY(0, 0, KEY_UP),
- KEY(1, 0, KEY_RIGHT),
- KEY(2, 0, KEY_LEFT),
- KEY(3, 0, KEY_DOWN),
- KEY(4, 0, KEY_ENTER),
- KEY(0, 1, KEY_F10),
- KEY(1, 1, KEY_SEND),
- KEY(2, 1, KEY_END),
- KEY(3, 1, KEY_VOLUMEDOWN),
- KEY(4, 1, KEY_VOLUMEUP),
- KEY(5, 1, KEY_RECORD),
- KEY(0, 2, KEY_F9),
- KEY(1, 2, KEY_3),
- KEY(2, 2, KEY_6),
- KEY(3, 2, KEY_9),
- KEY(4, 2, KEY_KPDOT),
- KEY(0, 3, KEY_BACK),
- KEY(1, 3, KEY_2),
- KEY(2, 3, KEY_5),
- KEY(3, 3, KEY_8),
- KEY(4, 3, KEY_0),
- KEY(5, 3, KEY_KPSLASH),
- KEY(0, 4, KEY_HOME),
- KEY(1, 4, KEY_1),
- KEY(2, 4, KEY_4),
- KEY(3, 4, KEY_7),
- KEY(4, 4, KEY_KPASTERISK),
- KEY(5, 4, KEY_POWER),
-};
-
-static struct smc91x_platdata smc91x_info = {
- .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
- .leda = RPC_LED_100_10,
- .ledb = RPC_LED_TX_RX,
-};
-
-static struct resource smc91x_resources[] = {
- [0] = {
- .start = H2P2_DBG_FPGA_ETHR_START, /* Physical */
- .end = H2P2_DBG_FPGA_ETHR_START + 0xf,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = INT_7XX_MPU_EXT_NIRQ,
- .end = 0,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
- },
-};
-
-static void __init fsample_init_smc91x(void)
-{
- __raw_writeb(1, H2P2_DBG_FPGA_LAN_RESET);
- mdelay(50);
- __raw_writeb(__raw_readb(H2P2_DBG_FPGA_LAN_RESET) & ~1,
- H2P2_DBG_FPGA_LAN_RESET);
- mdelay(50);
-}
-
-static struct mtd_partition nor_partitions[] = {
- /* bootloader (U-Boot, etc) in first sector */
- {
- .name = "bootloader",
- .offset = 0,
- .size = SZ_128K,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- /* bootloader params in the next sector */
- {
- .name = "params",
- .offset = MTDPART_OFS_APPEND,
- .size = SZ_128K,
- .mask_flags = 0,
- },
- /* kernel */
- {
- .name = "kernel",
- .offset = MTDPART_OFS_APPEND,
- .size = SZ_2M,
- .mask_flags = 0
- },
- /* rest of flash is a file system */
- {
- .name = "rootfs",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL,
- .mask_flags = 0
- },
-};
-
-static struct physmap_flash_data nor_data = {
- .width = 2,
- .set_vpp = omap1_set_vpp,
- .parts = nor_partitions,
- .nr_parts = ARRAY_SIZE(nor_partitions),
-};
-
-static struct resource nor_resource = {
- .start = OMAP_CS0_PHYS,
- .end = OMAP_CS0_PHYS + SZ_32M - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device nor_device = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &nor_data,
- },
- .num_resources = 1,
- .resource = &nor_resource,
-};
-
-#define FSAMPLE_NAND_RB_GPIO_PIN 62
-
-static int nand_dev_ready(struct nand_chip *chip)
-{
- return gpio_get_value(FSAMPLE_NAND_RB_GPIO_PIN);
-}
-
-static struct platform_nand_data nand_data = {
- .chip = {
- .nr_chips = 1,
- .chip_offset = 0,
- .options = NAND_SAMSUNG_LP_OPTIONS,
- },
- .ctrl = {
- .cmd_ctrl = omap1_nand_cmd_ctl,
- .dev_ready = nand_dev_ready,
- },
-};
-
-static struct resource nand_resource = {
- .start = OMAP_CS3_PHYS,
- .end = OMAP_CS3_PHYS + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device nand_device = {
- .name = "gen_nand",
- .id = 0,
- .dev = {
- .platform_data = &nand_data,
- },
- .num_resources = 1,
- .resource = &nand_resource,
-};
-
-static struct platform_device smc91x_device = {
- .name = "smc91x",
- .id = 0,
- .dev = {
- .platform_data = &smc91x_info,
- },
- .num_resources = ARRAY_SIZE(smc91x_resources),
- .resource = smc91x_resources,
-};
-
-static struct resource kp_resources[] = {
- [0] = {
- .start = INT_7XX_MPUIO_KEYPAD,
- .end = INT_7XX_MPUIO_KEYPAD,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static const struct matrix_keymap_data fsample_keymap_data = {
- .keymap = fsample_keymap,
- .keymap_size = ARRAY_SIZE(fsample_keymap),
-};
-
-static struct omap_kp_platform_data kp_data = {
- .rows = 8,
- .cols = 8,
- .keymap_data = &fsample_keymap_data,
- .delay = 4,
-};
-
-static struct platform_device kp_device = {
- .name = "omap-keypad",
- .id = -1,
- .dev = {
- .platform_data = &kp_data,
- },
- .num_resources = ARRAY_SIZE(kp_resources),
- .resource = kp_resources,
-};
-
-static struct platform_device *devices[] __initdata = {
- &nor_device,
- &nand_device,
- &smc91x_device,
- &kp_device,
-};
-
-static const struct omap_lcd_config fsample_lcd_config = {
- .ctrl_name = "internal",
-};
-
-static void __init omap_fsample_init(void)
-{
- /* Early, board-dependent init */
-
- /*
- * Hold GSM Reset until needed
- */
- omap_writew(omap_readw(OMAP7XX_DSP_M_CTL) & ~1, OMAP7XX_DSP_M_CTL);
-
- /*
- * UARTs -> done automagically by 8250 driver
- */
-
- /*
- * CSx timings, GPIO Mux ... setup
- */
-
- /* Flash: CS0 timings setup */
- omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_0);
- omap_writel(0x00000088, OMAP7XX_FLASH_ACFG_0);
-
- /*
- * Ethernet support through the debug board
- * CS1 timings setup
- */
- omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_1);
- omap_writel(0x00000000, OMAP7XX_FLASH_ACFG_1);
-
- /*
- * Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
- * It is used as the Ethernet controller interrupt
- */
- omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF,
- OMAP7XX_IO_CONF_9);
-
- fsample_init_smc91x();
-
- BUG_ON(gpio_request(FSAMPLE_NAND_RB_GPIO_PIN, "NAND ready") < 0);
- gpio_direction_input(FSAMPLE_NAND_RB_GPIO_PIN);
-
- omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
- omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
-
- /* Mux pins for keypad */
- omap_cfg_reg(E2_7XX_KBR0);
- omap_cfg_reg(J7_7XX_KBR1);
- omap_cfg_reg(E1_7XX_KBR2);
- omap_cfg_reg(F3_7XX_KBR3);
- omap_cfg_reg(D2_7XX_KBR4);
- omap_cfg_reg(C2_7XX_KBC0);
- omap_cfg_reg(D3_7XX_KBC1);
- omap_cfg_reg(E4_7XX_KBC2);
- omap_cfg_reg(F4_7XX_KBC3);
- omap_cfg_reg(E3_7XX_KBC4);
-
- platform_add_devices(devices, ARRAY_SIZE(devices));
-
- omap_serial_init();
- omap_register_i2c_bus(1, 100, NULL, 0);
-
- omapfb_set_lcd_config(&fsample_lcd_config);
-}
-
-/* Only FPGA needs to be mapped here. All others are done with ioremap */
-static struct map_desc omap_fsample_io_desc[] __initdata = {
- {
- .virtual = H2P2_DBG_FPGA_BASE,
- .pfn = __phys_to_pfn(H2P2_DBG_FPGA_START),
- .length = H2P2_DBG_FPGA_SIZE,
- .type = MT_DEVICE
- },
- {
- .virtual = FSAMPLE_CPLD_BASE,
- .pfn = __phys_to_pfn(FSAMPLE_CPLD_START),
- .length = FSAMPLE_CPLD_SIZE,
- .type = MT_DEVICE
- }
-};
-
-static void __init omap_fsample_map_io(void)
-{
- omap15xx_map_io();
- iotable_init(omap_fsample_io_desc,
- ARRAY_SIZE(omap_fsample_io_desc));
-}
-
-MACHINE_START(OMAP_FSAMPLE, "OMAP730 F-Sample")
-/* Maintainer: Brian Swetland <swetland@google.com> */
- .atag_offset = 0x100,
- .map_io = omap_fsample_map_io,
- .init_early = omap1_init_early,
- .init_irq = omap1_init_irq,
- .handle_irq = omap1_handle_irq,
- .init_machine = omap_fsample_init,
- .init_late = omap1_init_late,
- .init_time = omap1_timer_init,
- .restart = omap1_restart,
-MACHINE_END
deleted file mode 100644
@@ -1,85 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-omap1/board-generic.c
- *
- * Modified from board-innovator1510.c
- *
- * Code for generic OMAP board. Should work on many OMAP systems where
- * the device drivers take care of all the necessary hardware initialization.
- * Do not put any board specific code to this file; create a new machine
- * type if you need custom low-level initializations.
- */
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "hardware.h"
-#include "mux.h"
-#include "usb.h"
-#include "common.h"
-
-/* assume no Mini-AB port */
-
-#ifdef CONFIG_ARCH_OMAP15XX
-static struct omap_usb_config generic1510_usb_config __initdata = {
- .register_host = 1,
- .register_dev = 1,
- .hmc_mode = 16,
- .pins[0] = 3,
-};
-#endif
-
-#if defined(CONFIG_ARCH_OMAP16XX)
-static struct omap_usb_config generic1610_usb_config __initdata = {
-#ifdef CONFIG_USB_OTG
- .otg = 1,
-#endif
- .register_host = 1,
- .register_dev = 1,
- .hmc_mode = 16,
- .pins[0] = 6,
-};
-#endif
-
-static void __init omap_generic_init(void)
-{
-#ifdef CONFIG_ARCH_OMAP15XX
- if (cpu_is_omap15xx()) {
- /* mux pins for uarts */
- omap_cfg_reg(UART1_TX);
- omap_cfg_reg(UART1_RTS);
- omap_cfg_reg(UART2_TX);
- omap_cfg_reg(UART2_RTS);
- omap_cfg_reg(UART3_TX);
- omap_cfg_reg(UART3_RX);
-
- omap1_usb_init(&generic1510_usb_config);
- }
-#endif
-#if defined(CONFIG_ARCH_OMAP16XX)
- if (!cpu_is_omap1510()) {
- omap1_usb_init(&generic1610_usb_config);
- }
-#endif
-
- omap_serial_init();
- omap_register_i2c_bus(1, 100, NULL, 0);
-}
-
-MACHINE_START(OMAP_GENERIC, "Generic OMAP1510/1610/1710")
- /* Maintainer: Tony Lindgren <tony@atomide.com> */
- .atag_offset = 0x100,
- .map_io = omap16xx_map_io,
- .init_early = omap1_init_early,
- .init_irq = omap1_init_irq,
- .handle_irq = omap1_handle_irq,
- .init_machine = omap_generic_init,
- .init_late = omap1_init_late,
- .init_time = omap1_timer_init,
- .restart = omap1_restart,
-MACHINE_END
deleted file mode 100644
@@ -1,74 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-omap1/board-h2-mmc.c
- *
- * Copyright (C) 2007 Instituto Nokia de Tecnologia - INdT
- * Author: Felipe Balbi <felipe.lima@indt.org.br>
- *
- * This code is based on linux/arch/arm/mach-omap2/board-n800-mmc.c, which is:
- * Copyright (C) 2006 Nokia Corporation
- */
-#include <linux/gpio.h>
-#include <linux/platform_device.h>
-#include <linux/platform_data/gpio-omap.h>
-#include <linux/mfd/tps65010.h>
-
-#include "board-h2.h"
-#include "mmc.h"
-
-#if IS_ENABLED(CONFIG_MMC_OMAP)
-
-static int mmc_set_power(struct device *dev, int slot, int power_on,
- int vdd)
-{
- gpio_set_value(H2_TPS_GPIO_MMC_PWR_EN, power_on);
- return 0;
-}
-
-static int mmc_late_init(struct device *dev)
-{
- int ret = gpio_request(H2_TPS_GPIO_MMC_PWR_EN, "MMC power");
- if (ret < 0)
- return ret;
-
- gpio_direction_output(H2_TPS_GPIO_MMC_PWR_EN, 0);
-
- return ret;
-}
-
-static void mmc_cleanup(struct device *dev)
-{
- gpio_free(H2_TPS_GPIO_MMC_PWR_EN);
-}
-
-/*
- * H2 could use the following functions tested:
- * - mmc_get_cover_state that uses OMAP_MPUIO(1)
- * - mmc_get_wp that uses OMAP_MPUIO(3)
- */
-static struct omap_mmc_platform_data mmc1_data = {
- .nr_slots = 1,
- .init = mmc_late_init,
- .cleanup = mmc_cleanup,
- .slots[0] = {
- .set_power = mmc_set_power,
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .name = "mmcblk",
- },
-};
-
-static struct omap_mmc_platform_data *mmc_data[OMAP16XX_NR_MMC];
-
-void __init h2_mmc_init(void)
-{
- mmc_data[0] = &mmc1_data;
- omap1_init_mmc(mmc_data, OMAP16XX_NR_MMC);
-}
-
-#else
-
-void __init h2_mmc_init(void)
-{
-}
-
-#endif
deleted file mode 100644
@@ -1,448 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-omap1/board-h2.c
- *
- * Board specific inits for OMAP-1610 H2
- *
- * Copyright (C) 2001 RidgeRun, Inc.
- * Author: Greg Lonnon <glonnon@ridgerun.com>
- *
- * Copyright (C) 2002 MontaVista Software, Inc.
- *
- * Separated FPGA interrupts from innovator1510.c and cleaned up for 2.6
- * Copyright (C) 2004 Nokia Corporation by Tony Lindrgen <tony@atomide.com>
- *
- * H2 specific changes and cleanup
- * Copyright (C) 2004 Nokia Corporation by Imre Deak <imre.deak@nokia.com>
- */
-#include <linux/gpio.h>
-#include <linux/gpio/machine.h>
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/i2c.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/platnand.h>
-#include <linux/mtd/physmap.h>
-#include <linux/input.h>
-#include <linux/mfd/tps65010.h>
-#include <linux/smc91x.h>
-#include <linux/omapfb.h>
-#include <linux/omap-dma.h>
-#include <linux/platform_data/gpio-omap.h>
-#include <linux/platform_data/keypad-omap.h>
-#include <linux/leds.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "tc.h"
-#include "mux.h"
-#include "flash.h"
-#include "hardware.h"
-#include "usb.h"
-#include "common.h"
-#include "board-h2.h"
-
-/* The first 16 SoC GPIO lines are on this GPIO chip */
-#define OMAP_GPIO_LABEL "gpio-0-15"
-
-/* At OMAP1610 Innovator the Ethernet is directly connected to CS1 */
-#define OMAP1610_ETHR_START 0x04000300
-
-static const unsigned int h2_keymap[] = {
- KEY(0, 0, KEY_LEFT),
- KEY(1, 0, KEY_RIGHT),
- KEY(2, 0, KEY_3),
- KEY(3, 0, KEY_F10),
- KEY(4, 0, KEY_F5),
- KEY(5, 0, KEY_9),
- KEY(0, 1, KEY_DOWN),
- KEY(1, 1, KEY_UP),
- KEY(2, 1, KEY_2),
- KEY(3, 1, KEY_F9),
- KEY(4, 1, KEY_F7),
- KEY(5, 1, KEY_0),
- KEY(0, 2, KEY_ENTER),
- KEY(1, 2, KEY_6),
- KEY(2, 2, KEY_1),
- KEY(3, 2, KEY_F2),
- KEY(4, 2, KEY_F6),
- KEY(5, 2, KEY_HOME),
- KEY(0, 3, KEY_8),
- KEY(1, 3, KEY_5),
- KEY(2, 3, KEY_F12),
- KEY(3, 3, KEY_F3),
- KEY(4, 3, KEY_F8),
- KEY(5, 3, KEY_END),
- KEY(0, 4, KEY_7),
- KEY(1, 4, KEY_4),
- KEY(2, 4, KEY_F11),
- KEY(3, 4, KEY_F1),
- KEY(4, 4, KEY_F4),
- KEY(5, 4, KEY_ESC),
- KEY(0, 5, KEY_F13),
- KEY(1, 5, KEY_F14),
- KEY(2, 5, KEY_F15),
- KEY(3, 5, KEY_F16),
- KEY(4, 5, KEY_SLEEP),
-};
-
-static struct mtd_partition h2_nor_partitions[] = {
- /* bootloader (U-Boot, etc) in first sector */
- {
- .name = "bootloader",
- .offset = 0,
- .size = SZ_128K,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- /* bootloader params in the next sector */
- {
- .name = "params",
- .offset = MTDPART_OFS_APPEND,
- .size = SZ_128K,
- .mask_flags = 0,
- },
- /* kernel */
- {
- .name = "kernel",
- .offset = MTDPART_OFS_APPEND,
- .size = SZ_2M,
- .mask_flags = 0
- },
- /* file system */
- {
- .name = "filesystem",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL,
- .mask_flags = 0
- }
-};
-
-static struct physmap_flash_data h2_nor_data = {
- .width = 2,
- .set_vpp = omap1_set_vpp,
- .parts = h2_nor_partitions,
- .nr_parts = ARRAY_SIZE(h2_nor_partitions),
-};
-
-static struct resource h2_nor_resource = {
- /* This is on CS3, wherever it's mapped */
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device h2_nor_device = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &h2_nor_data,
- },
- .num_resources = 1,
- .resource = &h2_nor_resource,
-};
-
-static struct mtd_partition h2_nand_partitions[] = {
-#if 0
- /* REVISIT: enable these partitions if you make NAND BOOT
- * work on your H2 (rev C or newer); published versions of
- * x-load only support P2 and H3.
- */
- {
- .name = "xloader",
- .offset = 0,
- .size = 64 * 1024,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "bootloader",
- .offset = MTDPART_OFS_APPEND,
- .size = 256 * 1024,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "params",
- .offset = MTDPART_OFS_APPEND,
- .size = 192 * 1024,
- },
- {
- .name = "kernel",
- .offset = MTDPART_OFS_APPEND,
- .size = 2 * SZ_1M,
- },
-#endif
- {
- .name = "filesystem",
- .size = MTDPART_SIZ_FULL,
- .offset = MTDPART_OFS_APPEND,
- },
-};
-
-#define H2_NAND_RB_GPIO_PIN 62
-
-static int h2_nand_dev_ready(struct nand_chip *chip)
-{
- return gpio_get_value(H2_NAND_RB_GPIO_PIN);
-}
-
-static struct platform_nand_data h2_nand_platdata = {
- .chip = {
- .nr_chips = 1,
- .chip_offset = 0,
- .nr_partitions = ARRAY_SIZE(h2_nand_partitions),
- .partitions = h2_nand_partitions,
- .options = NAND_SAMSUNG_LP_OPTIONS,
- },
- .ctrl = {
- .cmd_ctrl = omap1_nand_cmd_ctl,
- .dev_ready = h2_nand_dev_ready,
- },
-};
-
-static struct resource h2_nand_resource = {
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device h2_nand_device = {
- .name = "gen_nand",
- .id = 0,
- .dev = {
- .platform_data = &h2_nand_platdata,
- },
- .num_resources = 1,
- .resource = &h2_nand_resource,
-};
-
-static struct smc91x_platdata h2_smc91x_info = {
- .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
- .leda = RPC_LED_100_10,
- .ledb = RPC_LED_TX_RX,
-};
-
-static struct resource h2_smc91x_resources[] = {
- [0] = {
- .start = OMAP1610_ETHR_START, /* Physical */
- .end = OMAP1610_ETHR_START + 0xf,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
- },
-};
-
-static struct platform_device h2_smc91x_device = {
- .name = "smc91x",
- .id = 0,
- .dev = {
- .platform_data = &h2_smc91x_info,
- },
- .num_resources = ARRAY_SIZE(h2_smc91x_resources),
- .resource = h2_smc91x_resources,
-};
-
-static struct resource h2_kp_resources[] = {
- [0] = {
- .start = INT_KEYBOARD,
- .end = INT_KEYBOARD,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static const struct matrix_keymap_data h2_keymap_data = {
- .keymap = h2_keymap,
- .keymap_size = ARRAY_SIZE(h2_keymap),
-};
-
-static struct omap_kp_platform_data h2_kp_data = {
- .rows = 8,
- .cols = 8,
- .keymap_data = &h2_keymap_data,
- .rep = true,
- .delay = 9,
- .dbounce = true,
-};
-
-static struct platform_device h2_kp_device = {
- .name = "omap-keypad",
- .id = -1,
- .dev = {
- .platform_data = &h2_kp_data,
- },
- .num_resources = ARRAY_SIZE(h2_kp_resources),
- .resource = h2_kp_resources,
-};
-
-static const struct gpio_led h2_gpio_led_pins[] = {
- {
- .name = "h2:red",
- .default_trigger = "heartbeat",
- .gpio = 3,
- },
- {
- .name = "h2:green",
- .default_trigger = "cpu0",
- .gpio = OMAP_MPUIO(4),
- },
-};
-
-static struct gpio_led_platform_data h2_gpio_led_data = {
- .leds = h2_gpio_led_pins,
- .num_leds = ARRAY_SIZE(h2_gpio_led_pins),
-};
-
-static struct platform_device h2_gpio_leds = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &h2_gpio_led_data,
- },
-};
-
-static struct platform_device *h2_devices[] __initdata = {
- &h2_nor_device,
- &h2_nand_device,
- &h2_smc91x_device,
- &h2_kp_device,
- &h2_gpio_leds,
-};
-
-static void __init h2_init_smc91x(void)
-{
- if (gpio_request(0, "SMC91x irq") < 0) {
- printk("Error requesting gpio 0 for smc91x irq\n");
- return;
- }
-}
-
-static int tps_setup(struct i2c_client *client, void *context)
-{
- if (!IS_BUILTIN(CONFIG_TPS65010))
- return -ENOSYS;
-
- tps65010_config_vregs1(TPS_LDO2_ENABLE | TPS_VLDO2_3_0V |
- TPS_LDO1_ENABLE | TPS_VLDO1_3_0V);
-
- return 0;
-}
-
-static struct tps65010_board tps_board = {
- .base = H2_TPS_GPIO_BASE,
- .outmask = 0x0f,
- .setup = tps_setup,
-};
-
-static struct i2c_board_info __initdata h2_i2c_board_info[] = {
- {
- I2C_BOARD_INFO("tps65010", 0x48),
- .platform_data = &tps_board,
- }, {
- .type = "isp1301_omap",
- .addr = 0x2d,
- .dev_name = "isp1301",
- },
-};
-
-static struct gpiod_lookup_table isp1301_gpiod_table = {
- .dev_id = "isp1301",
- .table = {
- /* Active low since the irq triggers on falling edge */
- GPIO_LOOKUP(OMAP_GPIO_LABEL, 2,
- NULL, GPIO_ACTIVE_LOW),
- { },
- },
-};
-
-static struct omap_usb_config h2_usb_config __initdata = {
- /* usb1 has a Mini-AB port and external isp1301 transceiver */
- .otg = 2,
-
-#if IS_ENABLED(CONFIG_USB_OMAP)
- .hmc_mode = 19, /* 0:host(off) 1:dev|otg 2:disabled */
- /* .hmc_mode = 21,*/ /* 0:host(off) 1:dev(loopback) 2:host(loopback) */
-#elif IS_ENABLED(CONFIG_USB_OHCI_HCD)
- /* needs OTG cable, or NONSTANDARD (B-to-MiniB) */
- .hmc_mode = 20, /* 1:dev|otg(off) 1:host 2:disabled */
-#endif
-
- .pins[1] = 3,
-};
-
-static const struct omap_lcd_config h2_lcd_config __initconst = {
- .ctrl_name = "internal",
-};
-
-static void __init h2_init(void)
-{
- h2_init_smc91x();
-
- /* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
- * to address 0 by a dip switch), NAND on CS2B. The NAND driver will
- * notice whether a NAND chip is enabled at probe time.
- *
- * FIXME revC boards (and H3) support NAND-boot, with a dip switch to
- * put NOR on CS2B and NAND (which on H2 may be 16bit) on CS3. Try
- * detecting that in code here, to avoid probing every possible flash
- * configuration...
- */
- h2_nor_resource.end = h2_nor_resource.start = omap_cs3_phys();
- h2_nor_resource.end += SZ_32M - 1;
-
- h2_nand_resource.end = h2_nand_resource.start = OMAP_CS2B_PHYS;
- h2_nand_resource.end += SZ_4K - 1;
- BUG_ON(gpio_request(H2_NAND_RB_GPIO_PIN, "NAND ready") < 0);
- gpio_direction_input(H2_NAND_RB_GPIO_PIN);
-
- gpiod_add_lookup_table(&isp1301_gpiod_table);
-
- omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
- omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
-
- /* MMC: card detect and WP */
- /* omap_cfg_reg(U19_ARMIO1); */ /* CD */
- omap_cfg_reg(BALLOUT_V8_ARMIO3); /* WP */
-
- /* Mux pins for keypad */
- omap_cfg_reg(F18_1610_KBC0);
- omap_cfg_reg(D20_1610_KBC1);
- omap_cfg_reg(D19_1610_KBC2);
- omap_cfg_reg(E18_1610_KBC3);
- omap_cfg_reg(C21_1610_KBC4);
- omap_cfg_reg(G18_1610_KBR0);
- omap_cfg_reg(F19_1610_KBR1);
- omap_cfg_reg(H14_1610_KBR2);
- omap_cfg_reg(E20_1610_KBR3);
- omap_cfg_reg(E19_1610_KBR4);
- omap_cfg_reg(N19_1610_KBR5);
-
- /* GPIO based LEDs */
- omap_cfg_reg(P18_1610_GPIO3);
- omap_cfg_reg(MPUIO4);
-
- h2_smc91x_resources[1].start = gpio_to_irq(0);
- h2_smc91x_resources[1].end = gpio_to_irq(0);
- platform_add_devices(h2_devices, ARRAY_SIZE(h2_devices));
- omap_serial_init();
-
- /* ISP1301 IRQ wired at M14 */
- omap_cfg_reg(M14_1510_GPIO2);
- h2_i2c_board_info[0].irq = gpio_to_irq(58);
- omap_register_i2c_bus(1, 100, h2_i2c_board_info,
- ARRAY_SIZE(h2_i2c_board_info));
- omap1_usb_init(&h2_usb_config);
- h2_mmc_init();
-
- omapfb_set_lcd_config(&h2_lcd_config);
-}
-
-MACHINE_START(OMAP_H2, "TI-H2")
- /* Maintainer: Imre Deak <imre.deak@nokia.com> */
- .atag_offset = 0x100,
- .map_io = omap16xx_map_io,
- .init_early = omap1_init_early,
- .init_irq = omap1_init_irq,
- .handle_irq = omap1_handle_irq,
- .init_machine = h2_init,
- .init_late = omap1_init_late,
- .init_time = omap1_timer_init,
- .restart = omap1_restart,
-MACHINE_END
deleted file mode 100644
@@ -1,38 +0,0 @@
-/*
- * arch/arm/mach-omap1/board-h2.h
- *
- * Hardware definitions for TI OMAP1610 H2 board.
- *
- * Cleanup for Linux-2.6 by Dirk Behme <dirk.behme@de.bosch.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#ifndef __ASM_ARCH_OMAP_H2_H
-#define __ASM_ARCH_OMAP_H2_H
-
-#define H2_TPS_GPIO_BASE (OMAP_MAX_GPIO_LINES + 16 /* MPUIO */)
-# define H2_TPS_GPIO_MMC_PWR_EN (H2_TPS_GPIO_BASE + 3)
-
-extern void h2_mmc_init(void);
-
-#endif /* __ASM_ARCH_OMAP_H2_H */
-
deleted file mode 100644
@@ -1,64 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-omap1/board-h3-mmc.c
- *
- * Copyright (C) 2007 Instituto Nokia de Tecnologia - INdT
- * Author: Felipe Balbi <felipe.lima@indt.org.br>
- *
- * This code is based on linux/arch/arm/mach-omap2/board-n800-mmc.c, which is:
- * Copyright (C) 2006 Nokia Corporation
- */
-#include <linux/gpio.h>
-#include <linux/platform_device.h>
-
-#include <linux/mfd/tps65010.h>
-
-#include "common.h"
-#include "board-h3.h"
-#include "mmc.h"
-
-#if IS_ENABLED(CONFIG_MMC_OMAP)
-
-static int mmc_set_power(struct device *dev, int slot, int power_on,
- int vdd)
-{
- gpio_set_value(H3_TPS_GPIO_MMC_PWR_EN, power_on);
- return 0;
-}
-
-/*
- * H3 could use the following functions tested:
- * - mmc_get_cover_state that uses OMAP_MPUIO(1)
- * - mmc_get_wp that maybe uses OMAP_MPUIO(3)
- */
-static struct omap_mmc_platform_data mmc1_data = {
- .nr_slots = 1,
- .slots[0] = {
- .set_power = mmc_set_power,
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .name = "mmcblk",
- },
-};
-
-static struct omap_mmc_platform_data *mmc_data[OMAP16XX_NR_MMC];
-
-void __init h3_mmc_init(void)
-{
- int ret;
-
- ret = gpio_request(H3_TPS_GPIO_MMC_PWR_EN, "MMC power");
- if (ret < 0)
- return;
- gpio_direction_output(H3_TPS_GPIO_MMC_PWR_EN, 0);
-
- mmc_data[0] = &mmc1_data;
- omap1_init_mmc(mmc_data, OMAP16XX_NR_MMC);
-}
-
-#else
-
-void __init h3_mmc_init(void)
-{
-}
-
-#endif
deleted file mode 100644
@@ -1,455 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-omap1/board-h3.c
- *
- * This file contains OMAP1710 H3 specific code.
- *
- * Copyright (C) 2004 Texas Instruments, Inc.
- * Copyright (C) 2002 MontaVista Software, Inc.
- * Copyright (C) 2001 RidgeRun, Inc.
- * Author: RidgeRun, Inc.
- * Greg Lonnon (glonnon@ridgerun.com) or info@ridgerun.com
- */
-#include <linux/gpio.h>
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/major.h>
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-#include <linux/errno.h>
-#include <linux/workqueue.h>
-#include <linux/i2c.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/platnand.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
-#include <linux/input.h>
-#include <linux/spi/spi.h>
-#include <linux/mfd/tps65010.h>
-#include <linux/smc91x.h>
-#include <linux/omapfb.h>
-#include <linux/platform_data/gpio-omap.h>
-#include <linux/platform_data/keypad-omap.h>
-#include <linux/omap-dma.h>
-#include <linux/leds.h>
-
-#include <asm/setup.h>
-#include <asm/page.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "tc.h"
-#include "mux.h"
-#include "flash.h"
-#include "hardware.h"
-#include "irqs.h"
-#include "usb.h"
-#include "common.h"
-#include "board-h3.h"
-
-/* In OMAP1710 H3 the Ethernet is directly connected to CS1 */
-#define OMAP1710_ETHR_START 0x04000300
-
-#define H3_TS_GPIO 48
-
-static const unsigned int h3_keymap[] = {
- KEY(0, 0, KEY_LEFT),
- KEY(1, 0, KEY_RIGHT),
- KEY(2, 0, KEY_3),
- KEY(3, 0, KEY_F10),
- KEY(4, 0, KEY_F5),
- KEY(5, 0, KEY_9),
- KEY(0, 1, KEY_DOWN),
- KEY(1, 1, KEY_UP),
- KEY(2, 1, KEY_2),
- KEY(3, 1, KEY_F9),
- KEY(4, 1, KEY_F7),
- KEY(5, 1, KEY_0),
- KEY(0, 2, KEY_ENTER),
- KEY(1, 2, KEY_6),
- KEY(2, 2, KEY_1),
- KEY(3, 2, KEY_F2),
- KEY(4, 2, KEY_F6),
- KEY(5, 2, KEY_HOME),
- KEY(0, 3, KEY_8),
- KEY(1, 3, KEY_5),
- KEY(2, 3, KEY_F12),
- KEY(3, 3, KEY_F3),
- KEY(4, 3, KEY_F8),
- KEY(5, 3, KEY_END),
- KEY(0, 4, KEY_7),
- KEY(1, 4, KEY_4),
- KEY(2, 4, KEY_F11),
- KEY(3, 4, KEY_F1),
- KEY(4, 4, KEY_F4),
- KEY(5, 4, KEY_ESC),
- KEY(0, 5, KEY_F13),
- KEY(1, 5, KEY_F14),
- KEY(2, 5, KEY_F15),
- KEY(3, 5, KEY_F16),
- KEY(4, 5, KEY_SLEEP),
-};
-
-
-static struct mtd_partition nor_partitions[] = {
- /* bootloader (U-Boot, etc) in first sector */
- {
- .name = "bootloader",
- .offset = 0,
- .size = SZ_128K,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- /* bootloader params in the next sector */
- {
- .name = "params",
- .offset = MTDPART_OFS_APPEND,
- .size = SZ_128K,
- .mask_flags = 0,
- },
- /* kernel */
- {
- .name = "kernel",
- .offset = MTDPART_OFS_APPEND,
- .size = SZ_2M,
- .mask_flags = 0
- },
- /* file system */
- {
- .name = "filesystem",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL,
- .mask_flags = 0
- }
-};
-
-static struct physmap_flash_data nor_data = {
- .width = 2,
- .set_vpp = omap1_set_vpp,
- .parts = nor_partitions,
- .nr_parts = ARRAY_SIZE(nor_partitions),
-};
-
-static struct resource nor_resource = {
- /* This is on CS3, wherever it's mapped */
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device nor_device = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &nor_data,
- },
- .num_resources = 1,
- .resource = &nor_resource,
-};
-
-static struct mtd_partition nand_partitions[] = {
-#if 0
- /* REVISIT: enable these partitions if you make NAND BOOT work */
- {
- .name = "xloader",
- .offset = 0,
- .size = 64 * 1024,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "bootloader",
- .offset = MTDPART_OFS_APPEND,
- .size = 256 * 1024,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "params",
- .offset = MTDPART_OFS_APPEND,
- .size = 192 * 1024,
- },
- {
- .name = "kernel",
- .offset = MTDPART_OFS_APPEND,
- .size = 2 * SZ_1M,
- },
-#endif
- {
- .name = "filesystem",
- .size = MTDPART_SIZ_FULL,
- .offset = MTDPART_OFS_APPEND,
- },
-};
-
-#define H3_NAND_RB_GPIO_PIN 10
-
-static int nand_dev_ready(struct nand_chip *chip)
-{
- return gpio_get_value(H3_NAND_RB_GPIO_PIN);
-}
-
-static struct platform_nand_data nand_platdata = {
- .chip = {
- .nr_chips = 1,
- .chip_offset = 0,
- .nr_partitions = ARRAY_SIZE(nand_partitions),
- .partitions = nand_partitions,
- .options = NAND_SAMSUNG_LP_OPTIONS,
- },
- .ctrl = {
- .cmd_ctrl = omap1_nand_cmd_ctl,
- .dev_ready = nand_dev_ready,
-
- },
-};
-
-static struct resource nand_resource = {
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device nand_device = {
- .name = "gen_nand",
- .id = 0,
- .dev = {
- .platform_data = &nand_platdata,
- },
- .num_resources = 1,
- .resource = &nand_resource,
-};
-
-static struct smc91x_platdata smc91x_info = {
- .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
- .leda = RPC_LED_100_10,
- .ledb = RPC_LED_TX_RX,
-};
-
-static struct resource smc91x_resources[] = {
- [0] = {
- .start = OMAP1710_ETHR_START, /* Physical */
- .end = OMAP1710_ETHR_START + 0xf,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
- },
-};
-
-static struct platform_device smc91x_device = {
- .name = "smc91x",
- .id = 0,
- .dev = {
- .platform_data = &smc91x_info,
- },
- .num_resources = ARRAY_SIZE(smc91x_resources),
- .resource = smc91x_resources,
-};
-
-static void __init h3_init_smc91x(void)
-{
- omap_cfg_reg(W15_1710_GPIO40);
- if (gpio_request(40, "SMC91x irq") < 0) {
- printk("Error requesting gpio 40 for smc91x irq\n");
- return;
- }
-}
-
-#define GPTIMER_BASE 0xFFFB1400
-#define GPTIMER_REGS(x) (0xFFFB1400 + (x * 0x800))
-#define GPTIMER_REGS_SIZE 0x46
-
-static struct resource intlat_resources[] = {
- [0] = {
- .start = GPTIMER_REGS(0), /* Physical */
- .end = GPTIMER_REGS(0) + GPTIMER_REGS_SIZE,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = INT_1610_GPTIMER1,
- .end = INT_1610_GPTIMER1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device intlat_device = {
- .name = "omap_intlat",
- .id = 0,
- .num_resources = ARRAY_SIZE(intlat_resources),
- .resource = intlat_resources,
-};
-
-static struct resource h3_kp_resources[] = {
- [0] = {
- .start = INT_KEYBOARD,
- .end = INT_KEYBOARD,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static const struct matrix_keymap_data h3_keymap_data = {
- .keymap = h3_keymap,
- .keymap_size = ARRAY_SIZE(h3_keymap),
-};
-
-static struct omap_kp_platform_data h3_kp_data = {
- .rows = 8,
- .cols = 8,
- .keymap_data = &h3_keymap_data,
- .rep = true,
- .delay = 9,
- .dbounce = true,
-};
-
-static struct platform_device h3_kp_device = {
- .name = "omap-keypad",
- .id = -1,
- .dev = {
- .platform_data = &h3_kp_data,
- },
- .num_resources = ARRAY_SIZE(h3_kp_resources),
- .resource = h3_kp_resources,
-};
-
-static struct platform_device h3_lcd_device = {
- .name = "lcd_h3",
- .id = -1,
-};
-
-static struct spi_board_info h3_spi_board_info[] __initdata = {
- [0] = {
- .modalias = "tsc2101",
- .bus_num = 2,
- .chip_select = 0,
- .max_speed_hz = 16000000,
- /* .platform_data = &tsc_platform_data, */
- },
-};
-
-static const struct gpio_led h3_gpio_led_pins[] = {
- {
- .name = "h3:red",
- .default_trigger = "heartbeat",
- .gpio = 3,
- },
- {
- .name = "h3:green",
- .default_trigger = "cpu0",
- .gpio = OMAP_MPUIO(4),
- },
-};
-
-static struct gpio_led_platform_data h3_gpio_led_data = {
- .leds = h3_gpio_led_pins,
- .num_leds = ARRAY_SIZE(h3_gpio_led_pins),
-};
-
-static struct platform_device h3_gpio_leds = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &h3_gpio_led_data,
- },
-};
-
-static struct platform_device *devices[] __initdata = {
- &nor_device,
- &nand_device,
- &smc91x_device,
- &intlat_device,
- &h3_kp_device,
- &h3_lcd_device,
- &h3_gpio_leds,
-};
-
-static struct omap_usb_config h3_usb_config __initdata = {
- /* usb1 has a Mini-AB port and external isp1301 transceiver */
- .otg = 2,
-
-#if IS_ENABLED(CONFIG_USB_OMAP)
- .hmc_mode = 19, /* 0:host(off) 1:dev|otg 2:disabled */
-#elif IS_ENABLED(CONFIG_USB_OHCI_HCD)
- /* NONSTANDARD CABLE NEEDED (B-to-Mini-B) */
- .hmc_mode = 20, /* 1:dev|otg(off) 1:host 2:disabled */
-#endif
-
- .pins[1] = 3,
-};
-
-static const struct omap_lcd_config h3_lcd_config __initconst = {
- .ctrl_name = "internal",
-};
-
-static struct i2c_board_info __initdata h3_i2c_board_info[] = {
- {
- I2C_BOARD_INFO("tps65013", 0x48),
- },
- {
- I2C_BOARD_INFO("isp1301_omap", 0x2d),
- },
-};
-
-static void __init h3_init(void)
-{
- h3_init_smc91x();
-
- /* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
- * to address 0 by a dip switch), NAND on CS2B. The NAND driver will
- * notice whether a NAND chip is enabled at probe time.
- *
- * H3 support NAND-boot, with a dip switch to put NOR on CS2B and NAND
- * (which on H2 may be 16bit) on CS3. Try detecting that in code here,
- * to avoid probing every possible flash configuration...
- */
- nor_resource.end = nor_resource.start = omap_cs3_phys();
- nor_resource.end += SZ_32M - 1;
-
- nand_resource.end = nand_resource.start = OMAP_CS2B_PHYS;
- nand_resource.end += SZ_4K - 1;
- BUG_ON(gpio_request(H3_NAND_RB_GPIO_PIN, "NAND ready") < 0);
- gpio_direction_input(H3_NAND_RB_GPIO_PIN);
-
- /* GPIO10 Func_MUX_CTRL reg bit 29:27, Configure V2 to mode1 as GPIO */
- /* GPIO10 pullup/down register, Enable pullup on GPIO10 */
- omap_cfg_reg(V2_1710_GPIO10);
-
- /* Mux pins for keypad */
- omap_cfg_reg(F18_1610_KBC0);
- omap_cfg_reg(D20_1610_KBC1);
- omap_cfg_reg(D19_1610_KBC2);
- omap_cfg_reg(E18_1610_KBC3);
- omap_cfg_reg(C21_1610_KBC4);
- omap_cfg_reg(G18_1610_KBR0);
- omap_cfg_reg(F19_1610_KBR1);
- omap_cfg_reg(H14_1610_KBR2);
- omap_cfg_reg(E20_1610_KBR3);
- omap_cfg_reg(E19_1610_KBR4);
- omap_cfg_reg(N19_1610_KBR5);
-
- /* GPIO based LEDs */
- omap_cfg_reg(P18_1610_GPIO3);
- omap_cfg_reg(MPUIO4);
-
- smc91x_resources[1].start = gpio_to_irq(40);
- smc91x_resources[1].end = gpio_to_irq(40);
- platform_add_devices(devices, ARRAY_SIZE(devices));
- h3_spi_board_info[0].irq = gpio_to_irq(H3_TS_GPIO);
- spi_register_board_info(h3_spi_board_info,
- ARRAY_SIZE(h3_spi_board_info));
- omap_serial_init();
- h3_i2c_board_info[1].irq = gpio_to_irq(14);
- omap_register_i2c_bus(1, 100, h3_i2c_board_info,
- ARRAY_SIZE(h3_i2c_board_info));
- omap1_usb_init(&h3_usb_config);
- h3_mmc_init();
-
- omapfb_set_lcd_config(&h3_lcd_config);
-}
-
-MACHINE_START(OMAP_H3, "TI OMAP1710 H3 board")
- /* Maintainer: Texas Instruments, Inc. */
- .atag_offset = 0x100,
- .map_io = omap16xx_map_io,
- .init_early = omap1_init_early,
- .init_irq = omap1_init_irq,
- .handle_irq = omap1_handle_irq,
- .init_machine = h3_init,
- .init_late = omap1_init_late,
- .init_time = omap1_timer_init,
- .restart = omap1_restart,
-MACHINE_END
deleted file mode 100644
@@ -1,35 +0,0 @@
-/*
- * arch/arm/mach-omap1/board-h3.h
- *
- * Copyright (C) 2001 RidgeRun, Inc.
- * Copyright (C) 2004 Texas Instruments, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-#ifndef __ASM_ARCH_OMAP_H3_H
-#define __ASM_ARCH_OMAP_H3_H
-
-#define H3_TPS_GPIO_BASE (OMAP_MAX_GPIO_LINES + 16 /* MPUIO */)
-# define H3_TPS_GPIO_MMC_PWR_EN (H3_TPS_GPIO_BASE + 4)
-
-extern void h3_mmc_init(void);
-
-#endif /* __ASM_ARCH_OMAP_H3_H */
deleted file mode 100644
@@ -1,585 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * HTC Herald board configuration
- * Copyright (C) 2009 Cory Maccarrone <darkstar6262@gmail.com>
- * Copyright (C) 2009 Wing Linux
- *
- * Based on the board-htcwizard.c file from the linwizard project:
- * Copyright (C) 2006 Unai Uribarri
- * Copyright (C) 2008 linwizard.sourceforge.net
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/input.h>
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/gpio_keys.h>
-#include <linux/i2c.h>
-#include <linux/platform_data/i2c-gpio.h>
-#include <linux/htcpld.h>
-#include <linux/leds.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
-#include <linux/omapfb.h>
-#include <linux/platform_data/keypad-omap.h>
-#include <linux/soc/ti/omap1-io.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include "hardware.h"
-#include "omap7xx.h"
-#include "mmc.h"
-#include "irqs.h"
-#include "usb.h"
-#include "common.h"
-
-/* LCD register definition */
-#define OMAP_LCDC_CONTROL (0xfffec000 + 0x00)
-#define OMAP_LCDC_STATUS (0xfffec000 + 0x10)
-#define OMAP_DMA_LCD_CCR (0xfffee300 + 0xc2)
-#define OMAP_DMA_LCD_CTRL (0xfffee300 + 0xc4)
-#define OMAP_LCDC_CTRL_LCD_EN (1 << 0)
-#define OMAP_LCDC_STAT_DONE (1 << 0)
-
-/* GPIO definitions for the power button and keyboard slide switch */
-#define HTCHERALD_GPIO_POWER 139
-#define HTCHERALD_GPIO_SLIDE 174
-#define HTCHERALD_GIRQ_BTNS 141
-
-/* GPIO definitions for the touchscreen */
-#define HTCHERALD_GPIO_TS 76
-
-/* HTCPLD definitions */
-
-/*
- * CPLD Logic
- *
- * Chip 3 - 0x03
- *
- * Function 7 6 5 4 3 2 1 0
- * ------------------------------------
- * DPAD light x x x x x x x 1
- * SoundDev x x x x 1 x x x
- * Screen white 1 x x x x x x x
- * MMC power on x x x x x 1 x x
- * Happy times (n) 0 x x x x 1 x x
- *
- * Chip 4 - 0x04
- *
- * Function 7 6 5 4 3 2 1 0
- * ------------------------------------
- * Keyboard light x x x x x x x 1
- * LCD Bright (4) x x x x x 1 1 x
- * LCD Bright (3) x x x x x 0 1 x
- * LCD Bright (2) x x x x x 1 0 x
- * LCD Bright (1) x x x x x 0 0 x
- * LCD Off x x x x 0 x x x
- * LCD image (fb) 1 x x x x x x x
- * LCD image (white) 0 x x x x x x x
- * Caps lock LED x x 1 x x x x x
- *
- * Chip 5 - 0x05
- *
- * Function 7 6 5 4 3 2 1 0
- * ------------------------------------
- * Red (solid) x x x x x 1 x x
- * Red (flash) x x x x x x 1 x
- * Green (GSM flash) x x x x 1 x x x
- * Green (GSM solid) x x x 1 x x x x
- * Green (wifi flash) x x 1 x x x x x
- * Blue (bt flash) x 1 x x x x x x
- * DPAD Int Enable 1 x x x x x x 0
- *
- * (Combinations of the above can be made for different colors.)
- * The direction pad interrupt enable must be set each time the
- * interrupt is handled.
- *
- * Chip 6 - 0x06
- *
- * Function 7 6 5 4 3 2 1 0
- * ------------------------------------
- * Vibrator x x x x 1 x x x
- * Alt LED x x x 1 x x x x
- * Screen white 1 x x x x x x x
- * Screen white x x 1 x x x x x
- * Screen white x 0 x x x x x x
- * Enable kbd dpad x x x x x x 0 x
- * Happy Times 0 1 0 x x x 0 x
- */
-
-/*
- * HTCPLD GPIO lines start 16 after OMAP_MAX_GPIO_LINES to account
- * for the 16 MPUIO lines.
- */
-#define HTCPLD_GPIO_START_OFFSET (OMAP_MAX_GPIO_LINES + 16)
-#define HTCPLD_IRQ(chip, offset) (OMAP_IRQ_END + 8 * (chip) + (offset))
-#define HTCPLD_BASE(chip, offset) \
- (HTCPLD_GPIO_START_OFFSET + 8 * (chip) + (offset))
-
-#define HTCPLD_GPIO_LED_DPAD HTCPLD_BASE(0, 0)
-#define HTCPLD_GPIO_LED_KBD HTCPLD_BASE(1, 0)
-#define HTCPLD_GPIO_LED_CAPS HTCPLD_BASE(1, 5)
-#define HTCPLD_GPIO_LED_RED_FLASH HTCPLD_BASE(2, 1)
-#define HTCPLD_GPIO_LED_RED_SOLID HTCPLD_BASE(2, 2)
-#define HTCPLD_GPIO_LED_GREEN_FLASH HTCPLD_BASE(2, 3)
-#define HTCPLD_GPIO_LED_GREEN_SOLID HTCPLD_BASE(2, 4)
-#define HTCPLD_GPIO_LED_WIFI HTCPLD_BASE(2, 5)
-#define HTCPLD_GPIO_LED_BT HTCPLD_BASE(2, 6)
-#define HTCPLD_GPIO_LED_VIBRATE HTCPLD_BASE(3, 3)
-#define HTCPLD_GPIO_LED_ALT HTCPLD_BASE(3, 4)
-
-#define HTCPLD_GPIO_RIGHT_KBD HTCPLD_BASE(6, 7)
-#define HTCPLD_GPIO_UP_KBD HTCPLD_BASE(6, 6)
-#define HTCPLD_GPIO_LEFT_KBD HTCPLD_BASE(6, 5)
-#define HTCPLD_GPIO_DOWN_KBD HTCPLD_BASE(6, 4)
-
-#define HTCPLD_GPIO_RIGHT_DPAD HTCPLD_BASE(7, 7)
-#define HTCPLD_GPIO_UP_DPAD HTCPLD_BASE(7, 6)
-#define HTCPLD_GPIO_LEFT_DPAD HTCPLD_BASE(7, 5)
-#define HTCPLD_GPIO_DOWN_DPAD HTCPLD_BASE(7, 4)
-#define HTCPLD_GPIO_ENTER_DPAD HTCPLD_BASE(7, 3)
-
-/* Chip 5 */
-#define HTCPLD_IRQ_RIGHT_KBD HTCPLD_IRQ(0, 7)
-#define HTCPLD_IRQ_UP_KBD HTCPLD_IRQ(0, 6)
-#define HTCPLD_IRQ_LEFT_KBD HTCPLD_IRQ(0, 5)
-#define HTCPLD_IRQ_DOWN_KBD HTCPLD_IRQ(0, 4)
-
-/* Chip 6 */
-#define HTCPLD_IRQ_RIGHT_DPAD HTCPLD_IRQ(1, 7)
-#define HTCPLD_IRQ_UP_DPAD HTCPLD_IRQ(1, 6)
-#define HTCPLD_IRQ_LEFT_DPAD HTCPLD_IRQ(1, 5)
-#define HTCPLD_IRQ_DOWN_DPAD HTCPLD_IRQ(1, 4)
-#define HTCPLD_IRQ_ENTER_DPAD HTCPLD_IRQ(1, 3)
-
-/* Keyboard definition */
-
-static const unsigned int htc_herald_keymap[] = {
- KEY(0, 0, KEY_RECORD), /* Mail button */
- KEY(1, 0, KEY_CAMERA), /* Camera */
- KEY(2, 0, KEY_PHONE), /* Send key */
- KEY(3, 0, KEY_VOLUMEUP), /* Volume up */
- KEY(4, 0, KEY_F2), /* Right bar (landscape) */
- KEY(5, 0, KEY_MAIL), /* Win key (portrait) */
- KEY(6, 0, KEY_DIRECTORY), /* Right bar (portrait) */
- KEY(0, 1, KEY_LEFTCTRL), /* Windows key */
- KEY(1, 1, KEY_COMMA),
- KEY(2, 1, KEY_M),
- KEY(3, 1, KEY_K),
- KEY(4, 1, KEY_SLASH), /* OK key */
- KEY(5, 1, KEY_I),
- KEY(6, 1, KEY_U),
- KEY(0, 2, KEY_LEFTALT),
- KEY(1, 2, KEY_TAB),
- KEY(2, 2, KEY_N),
- KEY(3, 2, KEY_J),
- KEY(4, 2, KEY_ENTER),
- KEY(5, 2, KEY_H),
- KEY(6, 2, KEY_Y),
- KEY(0, 3, KEY_SPACE),
- KEY(1, 3, KEY_L),
- KEY(2, 3, KEY_B),
- KEY(3, 3, KEY_V),
- KEY(4, 3, KEY_BACKSPACE),
- KEY(5, 3, KEY_G),
- KEY(6, 3, KEY_T),
- KEY(0, 4, KEY_CAPSLOCK), /* Shift */
- KEY(1, 4, KEY_C),
- KEY(2, 4, KEY_F),
- KEY(3, 4, KEY_R),
- KEY(4, 4, KEY_O),
- KEY(5, 4, KEY_E),
- KEY(6, 4, KEY_D),
- KEY(0, 5, KEY_X),
- KEY(1, 5, KEY_Z),
- KEY(2, 5, KEY_S),
- KEY(3, 5, KEY_W),
- KEY(4, 5, KEY_P),
- KEY(5, 5, KEY_Q),
- KEY(6, 5, KEY_A),
- KEY(0, 6, KEY_CONNECT), /* Voice button */
- KEY(2, 6, KEY_CANCEL), /* End key */
- KEY(3, 6, KEY_VOLUMEDOWN), /* Volume down */
- KEY(4, 6, KEY_F1), /* Left bar (landscape) */
- KEY(5, 6, KEY_WWW), /* OK button (portrait) */
- KEY(6, 6, KEY_CALENDAR), /* Left bar (portrait) */
-};
-
-static const struct matrix_keymap_data htc_herald_keymap_data = {
- .keymap = htc_herald_keymap,
- .keymap_size = ARRAY_SIZE(htc_herald_keymap),
-};
-
-static struct omap_kp_platform_data htcherald_kp_data = {
- .rows = 7,
- .cols = 7,
- .delay = 20,
- .rep = true,
- .keymap_data = &htc_herald_keymap_data,
-};
-
-static struct resource kp_resources[] = {
- [0] = {
- .start = INT_7XX_MPUIO_KEYPAD,
- .end = INT_7XX_MPUIO_KEYPAD,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device kp_device = {
- .name = "omap-keypad",
- .id = -1,
- .dev = {
- .platform_data = &htcherald_kp_data,
- },
- .num_resources = ARRAY_SIZE(kp_resources),
- .resource = kp_resources,
-};
-
-/* GPIO buttons for keyboard slide and power button */
-static struct gpio_keys_button herald_gpio_keys_table[] = {
- {BTN_0, HTCHERALD_GPIO_POWER, 1, "POWER", EV_KEY, 1, 20},
- {SW_LID, HTCHERALD_GPIO_SLIDE, 0, "SLIDE", EV_SW, 1, 20},
-
- {KEY_LEFT, HTCPLD_GPIO_LEFT_KBD, 1, "LEFT", EV_KEY, 1, 20},
- {KEY_RIGHT, HTCPLD_GPIO_RIGHT_KBD, 1, "RIGHT", EV_KEY, 1, 20},
- {KEY_UP, HTCPLD_GPIO_UP_KBD, 1, "UP", EV_KEY, 1, 20},
- {KEY_DOWN, HTCPLD_GPIO_DOWN_KBD, 1, "DOWN", EV_KEY, 1, 20},
-
- {KEY_LEFT, HTCPLD_GPIO_LEFT_DPAD, 1, "DLEFT", EV_KEY, 1, 20},
- {KEY_RIGHT, HTCPLD_GPIO_RIGHT_DPAD, 1, "DRIGHT", EV_KEY, 1, 20},
- {KEY_UP, HTCPLD_GPIO_UP_DPAD, 1, "DUP", EV_KEY, 1, 20},
- {KEY_DOWN, HTCPLD_GPIO_DOWN_DPAD, 1, "DDOWN", EV_KEY, 1, 20},
- {KEY_ENTER, HTCPLD_GPIO_ENTER_DPAD, 1, "DENTER", EV_KEY, 1, 20},
-};
-
-static struct gpio_keys_platform_data herald_gpio_keys_data = {
- .buttons = herald_gpio_keys_table,
- .nbuttons = ARRAY_SIZE(herald_gpio_keys_table),
- .rep = true,
-};
-
-static struct platform_device herald_gpiokeys_device = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &herald_gpio_keys_data,
- },
-};
-
-/* LEDs for the Herald. These connect to the HTCPLD GPIO device. */
-static const struct gpio_led gpio_leds[] = {
- {"dpad", NULL, HTCPLD_GPIO_LED_DPAD, 0, 0, LEDS_GPIO_DEFSTATE_OFF},
- {"kbd", NULL, HTCPLD_GPIO_LED_KBD, 0, 0, LEDS_GPIO_DEFSTATE_OFF},
- {"vibrate", NULL, HTCPLD_GPIO_LED_VIBRATE, 0, 0, LEDS_GPIO_DEFSTATE_OFF},
- {"green_solid", NULL, HTCPLD_GPIO_LED_GREEN_SOLID, 0, 0, LEDS_GPIO_DEFSTATE_OFF},
- {"green_flash", NULL, HTCPLD_GPIO_LED_GREEN_FLASH, 0, 0, LEDS_GPIO_DEFSTATE_OFF},
- {"red_solid", "mmc0", HTCPLD_GPIO_LED_RED_SOLID, 0, 0, LEDS_GPIO_DEFSTATE_OFF},
- {"red_flash", NULL, HTCPLD_GPIO_LED_RED_FLASH, 0, 0, LEDS_GPIO_DEFSTATE_OFF},
- {"wifi", NULL, HTCPLD_GPIO_LED_WIFI, 0, 0, LEDS_GPIO_DEFSTATE_OFF},
- {"bt", NULL, HTCPLD_GPIO_LED_BT, 0, 0, LEDS_GPIO_DEFSTATE_OFF},
- {"caps", NULL, HTCPLD_GPIO_LED_CAPS, 0, 0, LEDS_GPIO_DEFSTATE_OFF},
- {"alt", NULL, HTCPLD_GPIO_LED_ALT, 0, 0, LEDS_GPIO_DEFSTATE_OFF},
-};
-
-static struct gpio_led_platform_data gpio_leds_data = {
- .leds = gpio_leds,
- .num_leds = ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device gpio_leds_device = {
- .name = "leds-gpio",
- .id = 0,
- .dev = {
- .platform_data = &gpio_leds_data,
- },
-};
-
-/* HTC PLD chips */
-
-static struct resource htcpld_resources[] = {
- [0] = {
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct htcpld_chip_platform_data htcpld_chips[] = {
- [0] = {
- .addr = 0x03,
- .reset = 0x04,
- .num_gpios = 8,
- .gpio_out_base = HTCPLD_BASE(0, 0),
- .gpio_in_base = HTCPLD_BASE(4, 0),
- },
- [1] = {
- .addr = 0x04,
- .reset = 0x8e,
- .num_gpios = 8,
- .gpio_out_base = HTCPLD_BASE(1, 0),
- .gpio_in_base = HTCPLD_BASE(5, 0),
- },
- [2] = {
- .addr = 0x05,
- .reset = 0x80,
- .num_gpios = 8,
- .gpio_out_base = HTCPLD_BASE(2, 0),
- .gpio_in_base = HTCPLD_BASE(6, 0),
- .irq_base = HTCPLD_IRQ(0, 0),
- .num_irqs = 8,
- },
- [3] = {
- .addr = 0x06,
- .reset = 0x40,
- .num_gpios = 8,
- .gpio_out_base = HTCPLD_BASE(3, 0),
- .gpio_in_base = HTCPLD_BASE(7, 0),
- .irq_base = HTCPLD_IRQ(1, 0),
- .num_irqs = 8,
- },
-};
-
-static struct htcpld_core_platform_data htcpld_pfdata = {
- .i2c_adapter_id = 1,
-
- .chip = htcpld_chips,
- .num_chip = ARRAY_SIZE(htcpld_chips),
-};
-
-static struct platform_device htcpld_device = {
- .name = "i2c-htcpld",
- .id = -1,
- .resource = htcpld_resources,
- .num_resources = ARRAY_SIZE(htcpld_resources),
- .dev = {
- .platform_data = &htcpld_pfdata,
- },
-};
-
-/* USB Device */
-static struct omap_usb_config htcherald_usb_config __initdata = {
- .otg = 0,
- .register_host = 0,
- .register_dev = 1,
- .hmc_mode = 4,
- .pins[0] = 2,
-};
-
-/* LCD Device resources */
-static const struct omap_lcd_config htcherald_lcd_config __initconst = {
- .ctrl_name = "internal",
-};
-
-static struct platform_device lcd_device = {
- .name = "lcd_htcherald",
- .id = -1,
-};
-
-/* MMC Card */
-#if IS_ENABLED(CONFIG_MMC_OMAP)
-static struct omap_mmc_platform_data htc_mmc1_data = {
- .nr_slots = 1,
- .switch_slot = NULL,
- .slots[0] = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .name = "mmcblk",
- .nomux = 1,
- .wires = 4,
- .switch_pin = -1,
- },
-};
-
-static struct omap_mmc_platform_data *htc_mmc_data[1];
-#endif
-
-
-/* Platform devices for the Herald */
-static struct platform_device *devices[] __initdata = {
- &kp_device,
- &lcd_device,
- &htcpld_device,
- &gpio_leds_device,
- &herald_gpiokeys_device,
-};
-
-/*
- * Touchscreen
- */
-static const struct ads7846_platform_data htcherald_ts_platform_data = {
- .model = 7846,
- .keep_vref_on = 1,
- .x_plate_ohms = 496,
- .gpio_pendown = HTCHERALD_GPIO_TS,
- .pressure_max = 10000,
- .pressure_min = 5000,
- .x_min = 528,
- .x_max = 3760,
- .y_min = 624,
- .y_max = 3760,
-};
-
-static struct spi_board_info __initdata htcherald_spi_board_info[] = {
- {
- .modalias = "ads7846",
- .platform_data = &htcherald_ts_platform_data,
- .max_speed_hz = 2500000,
- .bus_num = 2,
- .chip_select = 1,
- }
-};
-
-/*
- * Init functions from here on
- */
-
-static void __init htcherald_lcd_init(void)
-{
- u32 reg;
- unsigned int tries = 200;
-
- /* disable controller if active */
- reg = omap_readl(OMAP_LCDC_CONTROL);
- if (reg & OMAP_LCDC_CTRL_LCD_EN) {
- reg &= ~OMAP_LCDC_CTRL_LCD_EN;
- omap_writel(reg, OMAP_LCDC_CONTROL);
-
- /* wait for end of frame */
- while (!(omap_readl(OMAP_LCDC_STATUS) & OMAP_LCDC_STAT_DONE)) {
- tries--;
- if (!tries)
- break;
- }
- if (!tries)
- pr_err("Timeout waiting for end of frame -- LCD may not be available\n");
-
- /* turn off DMA */
- reg = omap_readw(OMAP_DMA_LCD_CCR);
- reg &= ~(1 << 7);
- omap_writew(reg, OMAP_DMA_LCD_CCR);
-
- reg = omap_readw(OMAP_DMA_LCD_CTRL);
- reg &= ~(1 << 8);
- omap_writew(reg, OMAP_DMA_LCD_CTRL);
- }
-}
-
-static void __init htcherald_map_io(void)
-{
- omap7xx_map_io();
-
- /*
- * The LCD panel must be disabled and DMA turned off here, as doing
- * it later causes the LCD never to reinitialize.
- */
- htcherald_lcd_init();
-
- printk(KERN_INFO "htcherald_map_io done.\n");
-}
-
-static void __init htcherald_disable_watchdog(void)
-{
- /* Disable watchdog if running */
- if (omap_readl(OMAP_WDT_TIMER_MODE) & 0x8000) {
- /*
- * disable a potentially running watchdog timer before
- * it kills us.
- */
- printk(KERN_WARNING "OMAP850 Watchdog seems to be activated, disabling it for now.\n");
- omap_writel(0xF5, OMAP_WDT_TIMER_MODE);
- omap_writel(0xA0, OMAP_WDT_TIMER_MODE);
- }
-}
-
-#define HTCHERALD_GPIO_USB_EN1 33
-#define HTCHERALD_GPIO_USB_EN2 73
-#define HTCHERALD_GPIO_USB_DM 35
-#define HTCHERALD_GPIO_USB_DP 36
-
-static void __init htcherald_usb_enable(void)
-{
- unsigned int tries = 20;
- unsigned int value = 0;
-
- /* Request the GPIOs we need to control here */
- if (gpio_request(HTCHERALD_GPIO_USB_EN1, "herald_usb") < 0)
- goto err1;
-
- if (gpio_request(HTCHERALD_GPIO_USB_EN2, "herald_usb") < 0)
- goto err2;
-
- if (gpio_request(HTCHERALD_GPIO_USB_DM, "herald_usb") < 0)
- goto err3;
-
- if (gpio_request(HTCHERALD_GPIO_USB_DP, "herald_usb") < 0)
- goto err4;
-
- /* force USB_EN GPIO to 0 */
- do {
- /* output low */
- gpio_direction_output(HTCHERALD_GPIO_USB_EN1, 0);
- } while ((value = gpio_get_value(HTCHERALD_GPIO_USB_EN1)) == 1 &&
- --tries);
-
- if (value == 1)
- printk(KERN_WARNING "Unable to reset USB, trying to continue\n");
-
- gpio_direction_output(HTCHERALD_GPIO_USB_EN2, 0); /* output low */
- gpio_direction_input(HTCHERALD_GPIO_USB_DM); /* input */
- gpio_direction_input(HTCHERALD_GPIO_USB_DP); /* input */
-
- goto done;
-
-err4:
- gpio_free(HTCHERALD_GPIO_USB_DM);
-err3:
- gpio_free(HTCHERALD_GPIO_USB_EN2);
-err2:
- gpio_free(HTCHERALD_GPIO_USB_EN1);
-err1:
- printk(KERN_ERR "Unabled to request GPIO for USB\n");
-done:
- printk(KERN_INFO "USB setup complete.\n");
-}
-
-static void __init htcherald_init(void)
-{
- printk(KERN_INFO "HTC Herald init.\n");
-
- /* Do board initialization before we register all the devices */
- htcpld_resources[0].start = gpio_to_irq(HTCHERALD_GIRQ_BTNS);
- htcpld_resources[0].end = gpio_to_irq(HTCHERALD_GIRQ_BTNS);
- platform_add_devices(devices, ARRAY_SIZE(devices));
-
- htcherald_disable_watchdog();
-
- htcherald_usb_enable();
- omap1_usb_init(&htcherald_usb_config);
-
- htcherald_spi_board_info[0].irq = gpio_to_irq(HTCHERALD_GPIO_TS);
- spi_register_board_info(htcherald_spi_board_info,
- ARRAY_SIZE(htcherald_spi_board_info));
-
- omap_register_i2c_bus(1, 100, NULL, 0);
-
-#if IS_ENABLED(CONFIG_MMC_OMAP)
- htc_mmc_data[0] = &htc_mmc1_data;
- omap1_init_mmc(htc_mmc_data, 1);
-#endif
-
- omapfb_set_lcd_config(&htcherald_lcd_config);
-}
-
-MACHINE_START(HERALD, "HTC Herald")
- /* Maintainer: Cory Maccarrone <darkstar6262@gmail.com> */
- /* Maintainer: wing-linux.sourceforge.net */
- .atag_offset = 0x100,
- .map_io = htcherald_map_io,
- .init_early = omap1_init_early,
- .init_irq = omap1_init_irq,
- .handle_irq = omap1_handle_irq,
- .init_machine = htcherald_init,
- .init_late = omap1_init_late,
- .init_time = omap1_timer_init,
- .restart = omap1_restart,
-MACHINE_END
deleted file mode 100644
@@ -1,481 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-omap1/board-innovator.c
- *
- * Board specific inits for OMAP-1510 and OMAP-1610 Innovator
- *
- * Copyright (C) 2001 RidgeRun, Inc.
- * Author: Greg Lonnon <glonnon@ridgerun.com>
- *
- * Copyright (C) 2002 MontaVista Software, Inc.
- *
- * Separated FPGA interrupts from innovator1510.c and cleaned up for 2.6
- * Copyright (C) 2004 Nokia Corporation by Tony Lindrgen <tony@atomide.com>
- */
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
-#include <linux/input.h>
-#include <linux/smc91x.h>
-#include <linux/omapfb.h>
-#include <linux/platform_data/keypad-omap.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "tc.h"
-#include "mux.h"
-#include "flash.h"
-#include "hardware.h"
-#include "usb.h"
-#include "iomap.h"
-#include "common.h"
-#include "mmc.h"
-
-/* At OMAP1610 Innovator the Ethernet is directly connected to CS1 */
-#define INNOVATOR1610_ETHR_START 0x04000300
-
-static const unsigned int innovator_keymap[] = {
- KEY(0, 0, KEY_F1),
- KEY(3, 0, KEY_DOWN),
- KEY(1, 1, KEY_F2),
- KEY(2, 1, KEY_RIGHT),
- KEY(0, 2, KEY_F3),
- KEY(1, 2, KEY_F4),
- KEY(2, 2, KEY_UP),
- KEY(2, 3, KEY_ENTER),
- KEY(3, 3, KEY_LEFT),
-};
-
-static struct mtd_partition innovator_partitions[] = {
- /* bootloader (U-Boot, etc) in first sector */
- {
- .name = "bootloader",
- .offset = 0,
- .size = SZ_128K,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- /* bootloader params in the next sector */
- {
- .name = "params",
- .offset = MTDPART_OFS_APPEND,
- .size = SZ_128K,
- .mask_flags = 0,
- },
- /* kernel */
- {
- .name = "kernel",
- .offset = MTDPART_OFS_APPEND,
- .size = SZ_2M,
- .mask_flags = 0
- },
- /* rest of flash1 is a file system */
- {
- .name = "rootfs",
- .offset = MTDPART_OFS_APPEND,
- .size = SZ_16M - SZ_2M - 2 * SZ_128K,
- .mask_flags = 0
- },
- /* file system */
- {
- .name = "filesystem",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL,
- .mask_flags = 0
- }
-};
-
-static struct physmap_flash_data innovator_flash_data = {
- .width = 2,
- .set_vpp = omap1_set_vpp,
- .parts = innovator_partitions,
- .nr_parts = ARRAY_SIZE(innovator_partitions),
-};
-
-static struct resource innovator_flash_resource = {
- .start = OMAP_CS0_PHYS,
- .end = OMAP_CS0_PHYS + SZ_32M - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device innovator_flash_device = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &innovator_flash_data,
- },
- .num_resources = 1,
- .resource = &innovator_flash_resource,
-};
-
-static struct resource innovator_kp_resources[] = {
- [0] = {
- .start = INT_KEYBOARD,
- .end = INT_KEYBOARD,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static const struct matrix_keymap_data innovator_keymap_data = {
- .keymap = innovator_keymap,
- .keymap_size = ARRAY_SIZE(innovator_keymap),
-};
-
-static struct omap_kp_platform_data innovator_kp_data = {
- .rows = 8,
- .cols = 8,
- .keymap_data = &innovator_keymap_data,
- .delay = 4,
-};
-
-static struct platform_device innovator_kp_device = {
- .name = "omap-keypad",
- .id = -1,
- .dev = {
- .platform_data = &innovator_kp_data,
- },
- .num_resources = ARRAY_SIZE(innovator_kp_resources),
- .resource = innovator_kp_resources,
-};
-
-static struct smc91x_platdata innovator_smc91x_info = {
- .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
- .leda = RPC_LED_100_10,
- .ledb = RPC_LED_TX_RX,
-};
-
-#ifdef CONFIG_ARCH_OMAP15XX
-
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
-
-
-/* Only FPGA needs to be mapped here. All others are done with ioremap */
-static struct map_desc innovator1510_io_desc[] __initdata = {
- {
- .virtual = OMAP1510_FPGA_BASE,
- .pfn = __phys_to_pfn(OMAP1510_FPGA_START),
- .length = OMAP1510_FPGA_SIZE,
- .type = MT_DEVICE
- }
-};
-
-static struct resource innovator1510_smc91x_resources[] = {
- [0] = {
- .start = OMAP1510_FPGA_ETHR_START, /* Physical */
- .end = OMAP1510_FPGA_ETHR_START + 0xf,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = OMAP1510_INT_ETHER,
- .end = OMAP1510_INT_ETHER,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
- },
-};
-
-static struct platform_device innovator1510_smc91x_device = {
- .name = "smc91x",
- .id = 0,
- .dev = {
- .platform_data = &innovator_smc91x_info,
- },
- .num_resources = ARRAY_SIZE(innovator1510_smc91x_resources),
- .resource = innovator1510_smc91x_resources,
-};
-
-static struct platform_device innovator1510_lcd_device = {
- .name = "lcd_inn1510",
- .id = -1,
- .dev = {
- .platform_data = (void __force *)OMAP1510_FPGA_LCD_PANEL_CONTROL,
- }
-};
-
-static struct platform_device innovator1510_spi_device = {
- .name = "spi_inn1510",
- .id = -1,
-};
-
-static struct platform_device *innovator1510_devices[] __initdata = {
- &innovator_flash_device,
- &innovator1510_smc91x_device,
- &innovator_kp_device,
- &innovator1510_lcd_device,
- &innovator1510_spi_device,
-};
-
-static int innovator_get_pendown_state(void)
-{
- return !(__raw_readb(OMAP1510_FPGA_TOUCHSCREEN) & (1 << 5));
-}
-
-static const struct ads7846_platform_data innovator1510_ts_info = {
- .model = 7846,
- .vref_delay_usecs = 100, /* internal, no capacitor */
- .x_plate_ohms = 419,
- .y_plate_ohms = 486,
- .get_pendown_state = innovator_get_pendown_state,
-};
-
-static struct spi_board_info __initdata innovator1510_boardinfo[] = { {
- /* FPGA (bus "10") CS0 has an ads7846e */
- .modalias = "ads7846",
- .platform_data = &innovator1510_ts_info,
- .irq = OMAP1510_INT_FPGA_TS,
- .max_speed_hz = 120000 /* max sample rate at 3V */
- * 26 /* command + data + overhead */,
- .bus_num = 10,
- .chip_select = 0,
-} };
-
-#endif /* CONFIG_ARCH_OMAP15XX */
-
-#ifdef CONFIG_ARCH_OMAP16XX
-
-static struct resource innovator1610_smc91x_resources[] = {
- [0] = {
- .start = INNOVATOR1610_ETHR_START, /* Physical */
- .end = INNOVATOR1610_ETHR_START + 0xf,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
- },
-};
-
-static struct platform_device innovator1610_smc91x_device = {
- .name = "smc91x",
- .id = 0,
- .dev = {
- .platform_data = &innovator_smc91x_info,
- },
- .num_resources = ARRAY_SIZE(innovator1610_smc91x_resources),
- .resource = innovator1610_smc91x_resources,
-};
-
-static struct platform_device innovator1610_lcd_device = {
- .name = "inn1610_lcd",
- .id = -1,
-};
-
-static struct platform_device *innovator1610_devices[] __initdata = {
- &innovator_flash_device,
- &innovator1610_smc91x_device,
- &innovator_kp_device,
- &innovator1610_lcd_device,
-};
-
-#endif /* CONFIG_ARCH_OMAP16XX */
-
-static void __init innovator_init_smc91x(void)
-{
- if (cpu_is_omap1510()) {
- __raw_writeb(__raw_readb(OMAP1510_FPGA_RST) & ~1,
- OMAP1510_FPGA_RST);
- udelay(750);
- } else {
- if (gpio_request(0, "SMC91x irq") < 0) {
- printk("Error requesting gpio 0 for smc91x irq\n");
- return;
- }
- }
-}
-
-#ifdef CONFIG_ARCH_OMAP15XX
-/*
- * Board specific gang-switched transceiver power on/off.
- */
-static int innovator_omap_ohci_transceiver_power(int on)
-{
- if (on)
- __raw_writeb(__raw_readb(INNOVATOR_FPGA_CAM_USB_CONTROL)
- | ((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
- INNOVATOR_FPGA_CAM_USB_CONTROL);
- else
- __raw_writeb(__raw_readb(INNOVATOR_FPGA_CAM_USB_CONTROL)
- & ~((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
- INNOVATOR_FPGA_CAM_USB_CONTROL);
-
- return 0;
-}
-
-static struct omap_usb_config innovator1510_usb_config __initdata = {
- /* for bundled non-standard host and peripheral cables */
- .hmc_mode = 4,
-
- .register_host = 1,
- .pins[1] = 6,
- .pins[2] = 6, /* Conflicts with UART2 */
-
- .register_dev = 1,
- .pins[0] = 2,
-
- .transceiver_power = innovator_omap_ohci_transceiver_power,
-};
-
-static const struct omap_lcd_config innovator1510_lcd_config __initconst = {
- .ctrl_name = "internal",
-};
-#endif
-
-#ifdef CONFIG_ARCH_OMAP16XX
-static struct omap_usb_config h2_usb_config __initdata = {
- /* usb1 has a Mini-AB port and external isp1301 transceiver */
- .otg = 2,
-
-#if IS_ENABLED(CONFIG_USB_OMAP)
- .hmc_mode = 19, /* 0:host(off) 1:dev|otg 2:disabled */
- /* .hmc_mode = 21,*/ /* 0:host(off) 1:dev(loopback) 2:host(loopback) */
-#elif IS_ENABLED(CONFIG_USB_OHCI_HCD)
- /* NONSTANDARD CABLE NEEDED (B-to-Mini-B) */
- .hmc_mode = 20, /* 1:dev|otg(off) 1:host 2:disabled */
-#endif
-
- .pins[1] = 3,
-};
-
-static const struct omap_lcd_config innovator1610_lcd_config __initconst = {
- .ctrl_name = "internal",
-};
-#endif
-
-#if IS_ENABLED(CONFIG_MMC_OMAP)
-
-static int mmc_set_power(struct device *dev, int slot, int power_on,
- int vdd)
-{
- if (power_on)
- __raw_writeb(__raw_readb(OMAP1510_FPGA_POWER) | (1 << 3),
- OMAP1510_FPGA_POWER);
- else
- __raw_writeb(__raw_readb(OMAP1510_FPGA_POWER) & ~(1 << 3),
- OMAP1510_FPGA_POWER);
-
- return 0;
-}
-
-/*
- * Innovator could use the following functions tested:
- * - mmc_get_wp that uses OMAP_MPUIO(3)
- * - mmc_get_cover_state that uses FPGA F4 UIO43
- */
-static struct omap_mmc_platform_data mmc1_data = {
- .nr_slots = 1,
- .slots[0] = {
- .set_power = mmc_set_power,
- .wires = 4,
- .name = "mmcblk",
- },
-};
-
-static struct omap_mmc_platform_data *mmc_data[OMAP16XX_NR_MMC];
-
-static void __init innovator_mmc_init(void)
-{
- mmc_data[0] = &mmc1_data;
- omap1_init_mmc(mmc_data, OMAP15XX_NR_MMC);
-}
-
-#else
-static inline void innovator_mmc_init(void)
-{
-}
-#endif
-
-static void __init innovator_init(void)
-{
- if (cpu_is_omap1510())
- omap1510_fpga_init_irq();
- innovator_init_smc91x();
-
-#ifdef CONFIG_ARCH_OMAP15XX
- if (cpu_is_omap1510()) {
- unsigned char reg;
-
- /* mux pins for uarts */
- omap_cfg_reg(UART1_TX);
- omap_cfg_reg(UART1_RTS);
- omap_cfg_reg(UART2_TX);
- omap_cfg_reg(UART2_RTS);
- omap_cfg_reg(UART3_TX);
- omap_cfg_reg(UART3_RX);
-
- reg = __raw_readb(OMAP1510_FPGA_POWER);
- reg |= OMAP1510_FPGA_PCR_COM1_EN;
- __raw_writeb(reg, OMAP1510_FPGA_POWER);
- udelay(10);
-
- reg = __raw_readb(OMAP1510_FPGA_POWER);
- reg |= OMAP1510_FPGA_PCR_COM2_EN;
- __raw_writeb(reg, OMAP1510_FPGA_POWER);
- udelay(10);
-
- platform_add_devices(innovator1510_devices, ARRAY_SIZE(innovator1510_devices));
- spi_register_board_info(innovator1510_boardinfo,
- ARRAY_SIZE(innovator1510_boardinfo));
- }
-#endif
-#ifdef CONFIG_ARCH_OMAP16XX
- if (!cpu_is_omap1510()) {
- innovator1610_smc91x_resources[1].start = gpio_to_irq(0);
- innovator1610_smc91x_resources[1].end = gpio_to_irq(0);
- platform_add_devices(innovator1610_devices, ARRAY_SIZE(innovator1610_devices));
- }
-#endif
-
-#ifdef CONFIG_ARCH_OMAP15XX
- if (cpu_is_omap1510()) {
- omap1_usb_init(&innovator1510_usb_config);
- omapfb_set_lcd_config(&innovator1510_lcd_config);
- }
-#endif
-#ifdef CONFIG_ARCH_OMAP16XX
- if (cpu_is_omap1610()) {
- omap1_usb_init(&h2_usb_config);
- omapfb_set_lcd_config(&innovator1610_lcd_config);
- }
-#endif
- omap_serial_init();
- omap_register_i2c_bus(1, 100, NULL, 0);
- innovator_mmc_init();
-}
-
-/*
- * REVISIT: Assume 15xx for now, we don't want to do revision check
- * until later on. The right way to fix this is to set up a different
- * machine_id for 16xx Innovator, or use device tree.
- */
-static void __init innovator_map_io(void)
-{
-#ifdef CONFIG_ARCH_OMAP15XX
- omap15xx_map_io();
-
- iotable_init(innovator1510_io_desc, ARRAY_SIZE(innovator1510_io_desc));
- udelay(10); /* Delay needed for FPGA */
-
- /* Dump the Innovator FPGA rev early - useful info for support. */
- pr_debug("Innovator FPGA Rev %d.%d Board Rev %d\n",
- __raw_readb(OMAP1510_FPGA_REV_HIGH),
- __raw_readb(OMAP1510_FPGA_REV_LOW),
- __raw_readb(OMAP1510_FPGA_BOARD_REV));
-#endif
-}
-
-MACHINE_START(OMAP_INNOVATOR, "TI-Innovator")
- /* Maintainer: MontaVista Software, Inc. */
- .atag_offset = 0x100,
- .map_io = innovator_map_io,
- .init_early = omap1_init_early,
- .init_irq = omap1_init_irq,
- .handle_irq = omap1_handle_irq,
- .init_machine = innovator_init,
- .init_late = omap1_init_late,
- .init_time = omap1_timer_init,
- .restart = omap1_restart,
-MACHINE_END
deleted file mode 100644
@@ -1,33 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-omap1/board-nand.c
- *
- * Common OMAP1 board NAND code
- *
- * Copyright (C) 2004, 2012 Texas Instruments, Inc.
- * Copyright (C) 2002 MontaVista Software, Inc.
- * Copyright (C) 2001 RidgeRun, Inc.
- * Author: RidgeRun, Inc.
- * Greg Lonnon (glonnon@ridgerun.com) or info@ridgerun.com
- */
-#include <linux/kernel.h>
-#include <linux/io.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/rawnand.h>
-
-#include "common.h"
-
-void omap1_nand_cmd_ctl(struct nand_chip *this, int cmd, unsigned int ctrl)
-{
- unsigned long mask;
-
- if (cmd == NAND_CMD_NONE)
- return;
-
- mask = (ctrl & NAND_CLE) ? 0x02 : 0;
- if (ctrl & NAND_ALE)
- mask |= 0x04;
-
- writeb(cmd, this->legacy.IO_ADDR_W + mask);
-}
-
deleted file mode 100644
@@ -1,285 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-omap1/board-palmtt.c
- *
- * Modified from board-palmtt2.c
- *
- * Modified and amended for Palm Tungsten|T
- * by Marek Vasut <marek.vasut@gmail.com>
- */
-
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/notifier.h>
-#include <linux/clk.h>
-#include <linux/input.h>
-#include <linux/interrupt.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
-#include <linux/leds.h>
-#include <linux/omapfb.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
-#include <linux/omap-dma.h>
-#include <linux/platform_data/omap1_bl.h>
-#include <linux/platform_data/leds-omap.h>
-#include <linux/platform_data/keypad-omap.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "tc.h"
-#include "flash.h"
-#include "mux.h"
-#include "hardware.h"
-#include "usb.h"
-#include "common.h"
-
-#define PALMTT_USBDETECT_GPIO 0
-#define PALMTT_CABLE_GPIO 1
-#define PALMTT_LED_GPIO 3
-#define PALMTT_PENIRQ_GPIO 6
-#define PALMTT_MMC_WP_GPIO 8
-#define PALMTT_HDQ_GPIO 11
-
-static const unsigned int palmtt_keymap[] = {
- KEY(0, 0, KEY_ESC),
- KEY(1, 0, KEY_SPACE),
- KEY(2, 0, KEY_LEFTCTRL),
- KEY(3, 0, KEY_TAB),
- KEY(4, 0, KEY_ENTER),
- KEY(0, 1, KEY_LEFT),
- KEY(1, 1, KEY_DOWN),
- KEY(2, 1, KEY_UP),
- KEY(3, 1, KEY_RIGHT),
- KEY(0, 2, KEY_SLEEP),
- KEY(4, 2, KEY_Y),
-};
-
-static struct mtd_partition palmtt_partitions[] = {
- {
- .name = "write8k",
- .offset = 0,
- .size = SZ_8K,
- .mask_flags = 0,
- },
- {
- .name = "PalmOS-BootLoader(ro)",
- .offset = SZ_8K,
- .size = 7 * SZ_8K,
- .mask_flags = MTD_WRITEABLE,
- },
- {
- .name = "u-boot",
- .offset = MTDPART_OFS_APPEND,
- .size = 8 * SZ_8K,
- .mask_flags = 0,
- },
- {
- .name = "PalmOS-FS(ro)",
- .offset = MTDPART_OFS_APPEND,
- .size = 7 * SZ_1M + 4 * SZ_64K - 16 * SZ_8K,
- .mask_flags = MTD_WRITEABLE,
- },
- {
- .name = "u-boot(rez)",
- .offset = MTDPART_OFS_APPEND,
- .size = SZ_128K,
- .mask_flags = 0
- },
- {
- .name = "empty",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL,
- .mask_flags = 0
- }
-};
-
-static struct physmap_flash_data palmtt_flash_data = {
- .width = 2,
- .set_vpp = omap1_set_vpp,
- .parts = palmtt_partitions,
- .nr_parts = ARRAY_SIZE(palmtt_partitions),
-};
-
-static struct resource palmtt_flash_resource = {
- .start = OMAP_CS0_PHYS,
- .end = OMAP_CS0_PHYS + SZ_8M - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device palmtt_flash_device = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &palmtt_flash_data,
- },
- .num_resources = 1,
- .resource = &palmtt_flash_resource,
-};
-
-static struct resource palmtt_kp_resources[] = {
- [0] = {
- .start = INT_KEYBOARD,
- .end = INT_KEYBOARD,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static const struct matrix_keymap_data palmtt_keymap_data = {
- .keymap = palmtt_keymap,
- .keymap_size = ARRAY_SIZE(palmtt_keymap),
-};
-
-static struct omap_kp_platform_data palmtt_kp_data = {
- .rows = 6,
- .cols = 3,
- .keymap_data = &palmtt_keymap_data,
-};
-
-static struct platform_device palmtt_kp_device = {
- .name = "omap-keypad",
- .id = -1,
- .dev = {
- .platform_data = &palmtt_kp_data,
- },
- .num_resources = ARRAY_SIZE(palmtt_kp_resources),
- .resource = palmtt_kp_resources,
-};
-
-static struct platform_device palmtt_lcd_device = {
- .name = "lcd_palmtt",
- .id = -1,
-};
-
-static struct platform_device palmtt_spi_device = {
- .name = "spi_palmtt",
- .id = -1,
-};
-
-static struct omap_backlight_config palmtt_backlight_config = {
- .default_intensity = 0xa0,
-};
-
-static struct platform_device palmtt_backlight_device = {
- .name = "omap-bl",
- .id = -1,
- .dev = {
- .platform_data= &palmtt_backlight_config,
- },
-};
-
-static struct omap_led_config palmtt_led_config[] = {
- {
- .cdev = {
- .name = "palmtt:led0",
- },
- .gpio = PALMTT_LED_GPIO,
- },
-};
-
-static struct omap_led_platform_data palmtt_led_data = {
- .nr_leds = ARRAY_SIZE(palmtt_led_config),
- .leds = palmtt_led_config,
-};
-
-static struct platform_device palmtt_led_device = {
- .name = "omap-led",
- .id = -1,
- .dev = {
- .platform_data = &palmtt_led_data,
- },
-};
-
-static struct platform_device *palmtt_devices[] __initdata = {
- &palmtt_flash_device,
- &palmtt_kp_device,
- &palmtt_lcd_device,
- &palmtt_spi_device,
- &palmtt_backlight_device,
- &palmtt_led_device,
-};
-
-static int palmtt_get_pendown_state(void)
-{
- return !gpio_get_value(6);
-}
-
-static const struct ads7846_platform_data palmtt_ts_info = {
- .model = 7846,
- .vref_delay_usecs = 100, /* internal, no capacitor */
- .x_plate_ohms = 419,
- .y_plate_ohms = 486,
- .get_pendown_state = palmtt_get_pendown_state,
-};
-
-static struct spi_board_info __initdata palmtt_boardinfo[] = {
- {
- /* MicroWire (bus 2) CS0 has an ads7846e */
- .modalias = "ads7846",
- .platform_data = &palmtt_ts_info,
- .max_speed_hz = 120000 /* max sample rate at 3V */
- * 26 /* command + data + overhead */,
- .bus_num = 2,
- .chip_select = 0,
- }
-};
-
-static struct omap_usb_config palmtt_usb_config __initdata = {
- .register_dev = 1,
- .hmc_mode = 0,
- .pins[0] = 2,
-};
-
-static const struct omap_lcd_config palmtt_lcd_config __initconst = {
- .ctrl_name = "internal",
-};
-
-static void __init omap_mpu_wdt_mode(int mode) {
- if (mode)
- omap_writew(0x8000, OMAP_WDT_TIMER_MODE);
- else {
- omap_writew(0x00f5, OMAP_WDT_TIMER_MODE);
- omap_writew(0x00a0, OMAP_WDT_TIMER_MODE);
- }
-}
-
-static void __init omap_palmtt_init(void)
-{
- /* mux pins for uarts */
- omap_cfg_reg(UART1_TX);
- omap_cfg_reg(UART1_RTS);
- omap_cfg_reg(UART2_TX);
- omap_cfg_reg(UART2_RTS);
- omap_cfg_reg(UART3_TX);
- omap_cfg_reg(UART3_RX);
-
- omap_mpu_wdt_mode(0);
-
- platform_add_devices(palmtt_devices, ARRAY_SIZE(palmtt_devices));
-
- palmtt_boardinfo[0].irq = gpio_to_irq(6);
- spi_register_board_info(palmtt_boardinfo,ARRAY_SIZE(palmtt_boardinfo));
- omap_serial_init();
- omap1_usb_init(&palmtt_usb_config);
- omap_register_i2c_bus(1, 100, NULL, 0);
-
- omapfb_set_lcd_config(&palmtt_lcd_config);
-}
-
-MACHINE_START(OMAP_PALMTT, "OMAP1510 based Palm Tungsten|T")
- .atag_offset = 0x100,
- .map_io = omap15xx_map_io,
- .init_early = omap1_init_early,
- .init_irq = omap1_init_irq,
- .handle_irq = omap1_handle_irq,
- .init_machine = omap_palmtt_init,
- .init_late = omap1_init_late,
- .init_time = omap1_timer_init,
- .restart = omap1_restart,
-MACHINE_END
deleted file mode 100644
@@ -1,300 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-omap1/board-palmz71.c
- *
- * Modified from board-generic.c
- *
- * Support for the Palm Zire71 PDA.
- *
- * Original version : Laurent Gonzalez
- *
- * Modified for zire71 : Marek Vasut
- */
-
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/notifier.h>
-#include <linux/clk.h>
-#include <linux/irq.h>
-#include <linux/input.h>
-#include <linux/interrupt.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
-#include <linux/omapfb.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
-#include <linux/platform_data/omap1_bl.h>
-#include <linux/platform_data/keypad-omap.h>
-#include <linux/omap-dma.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "tc.h"
-#include "flash.h"
-#include "mux.h"
-#include "hardware.h"
-#include "usb.h"
-#include "common.h"
-
-#define PALMZ71_USBDETECT_GPIO 0
-#define PALMZ71_PENIRQ_GPIO 6
-#define PALMZ71_MMC_WP_GPIO 8
-#define PALMZ71_HDQ_GPIO 11
-
-#define PALMZ71_HOTSYNC_GPIO OMAP_MPUIO(1)
-#define PALMZ71_CABLE_GPIO OMAP_MPUIO(2)
-#define PALMZ71_SLIDER_GPIO OMAP_MPUIO(3)
-#define PALMZ71_MMC_IN_GPIO OMAP_MPUIO(4)
-
-static const unsigned int palmz71_keymap[] = {
- KEY(0, 0, KEY_F1),
- KEY(1, 0, KEY_F2),
- KEY(2, 0, KEY_F3),
- KEY(3, 0, KEY_F4),
- KEY(4, 0, KEY_POWER),
- KEY(0, 1, KEY_LEFT),
- KEY(1, 1, KEY_DOWN),
- KEY(2, 1, KEY_UP),
- KEY(3, 1, KEY_RIGHT),
- KEY(4, 1, KEY_ENTER),
- KEY(0, 2, KEY_CAMERA),
-};
-
-static const struct matrix_keymap_data palmz71_keymap_data = {
- .keymap = palmz71_keymap,
- .keymap_size = ARRAY_SIZE(palmz71_keymap),
-};
-
-static struct omap_kp_platform_data palmz71_kp_data = {
- .rows = 8,
- .cols = 8,
- .keymap_data = &palmz71_keymap_data,
- .rep = true,
- .delay = 80,
-};
-
-static struct resource palmz71_kp_resources[] = {
- [0] = {
- .start = INT_KEYBOARD,
- .end = INT_KEYBOARD,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device palmz71_kp_device = {
- .name = "omap-keypad",
- .id = -1,
- .dev = {
- .platform_data = &palmz71_kp_data,
- },
- .num_resources = ARRAY_SIZE(palmz71_kp_resources),
- .resource = palmz71_kp_resources,
-};
-
-static struct mtd_partition palmz71_rom_partitions[] = {
- /* PalmOS "Small ROM", contains the bootloader and the debugger */
- {
- .name = "smallrom",
- .offset = 0,
- .size = 0xa000,
- .mask_flags = MTD_WRITEABLE,
- },
- /* PalmOS "Big ROM", a filesystem with all the OS code and data */
- {
- .name = "bigrom",
- .offset = SZ_128K,
- /*
- * 0x5f0000 bytes big in the multi-language ("EFIGS") version,
- * 0x7b0000 bytes in the English-only ("enUS") version.
- */
- .size = 0x7b0000,
- .mask_flags = MTD_WRITEABLE,
- },
-};
-
-static struct physmap_flash_data palmz71_rom_data = {
- .width = 2,
- .set_vpp = omap1_set_vpp,
- .parts = palmz71_rom_partitions,
- .nr_parts = ARRAY_SIZE(palmz71_rom_partitions),
-};
-
-static struct resource palmz71_rom_resource = {
- .start = OMAP_CS0_PHYS,
- .end = OMAP_CS0_PHYS + SZ_8M - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device palmz71_rom_device = {
- .name = "physmap-flash",
- .id = -1,
- .dev = {
- .platform_data = &palmz71_rom_data,
- },
- .num_resources = 1,
- .resource = &palmz71_rom_resource,
-};
-
-static struct platform_device palmz71_lcd_device = {
- .name = "lcd_palmz71",
- .id = -1,
-};
-
-static struct platform_device palmz71_spi_device = {
- .name = "spi_palmz71",
- .id = -1,
-};
-
-static struct omap_backlight_config palmz71_backlight_config = {
- .default_intensity = 0xa0,
-};
-
-static struct platform_device palmz71_backlight_device = {
- .name = "omap-bl",
- .id = -1,
- .dev = {
- .platform_data = &palmz71_backlight_config,
- },
-};
-
-static struct platform_device *devices[] __initdata = {
- &palmz71_rom_device,
- &palmz71_kp_device,
- &palmz71_lcd_device,
- &palmz71_spi_device,
- &palmz71_backlight_device,
-};
-
-static int
-palmz71_get_pendown_state(void)
-{
- return !gpio_get_value(PALMZ71_PENIRQ_GPIO);
-}
-
-static const struct ads7846_platform_data palmz71_ts_info = {
- .model = 7846,
- .vref_delay_usecs = 100, /* internal, no capacitor */
- .x_plate_ohms = 419,
- .y_plate_ohms = 486,
- .get_pendown_state = palmz71_get_pendown_state,
-};
-
-static struct spi_board_info __initdata palmz71_boardinfo[] = { {
- /* MicroWire (bus 2) CS0 has an ads7846e */
- .modalias = "ads7846",
- .platform_data = &palmz71_ts_info,
- .max_speed_hz = 120000 /* max sample rate at 3V */
- * 26 /* command + data + overhead */,
- .bus_num = 2,
- .chip_select = 0,
-} };
-
-static struct omap_usb_config palmz71_usb_config __initdata = {
- .register_dev = 1, /* Mini-B only receptacle */
- .hmc_mode = 0,
- .pins[0] = 2,
-};
-
-static const struct omap_lcd_config palmz71_lcd_config __initconst = {
- .ctrl_name = "internal",
-};
-
-static irqreturn_t
-palmz71_powercable(int irq, void *dev_id)
-{
- if (gpio_get_value(PALMZ71_USBDETECT_GPIO)) {
- printk(KERN_INFO "PM: Power cable connected\n");
- irq_set_irq_type(gpio_to_irq(PALMZ71_USBDETECT_GPIO),
- IRQ_TYPE_EDGE_FALLING);
- } else {
- printk(KERN_INFO "PM: Power cable disconnected\n");
- irq_set_irq_type(gpio_to_irq(PALMZ71_USBDETECT_GPIO),
- IRQ_TYPE_EDGE_RISING);
- }
- return IRQ_HANDLED;
-}
-
-static void __init
-omap_mpu_wdt_mode(int mode)
-{
- if (mode)
- omap_writew(0x8000, OMAP_WDT_TIMER_MODE);
- else {
- omap_writew(0x00f5, OMAP_WDT_TIMER_MODE);
- omap_writew(0x00a0, OMAP_WDT_TIMER_MODE);
- }
-}
-
-static void __init
-palmz71_gpio_setup(int early)
-{
- if (early) {
- /* Only set GPIO1 so we have a working serial */
- gpio_direction_output(1, 1);
- } else {
- /* Set MMC/SD host WP pin as input */
- if (gpio_request(PALMZ71_MMC_WP_GPIO, "MMC WP") < 0) {
- printk(KERN_ERR "Could not reserve WP GPIO!\n");
- return;
- }
- gpio_direction_input(PALMZ71_MMC_WP_GPIO);
-
- /* Monitor the Power-cable-connected signal */
- if (gpio_request(PALMZ71_USBDETECT_GPIO, "USB detect") < 0) {
- printk(KERN_ERR
- "Could not reserve cable signal GPIO!\n");
- return;
- }
- gpio_direction_input(PALMZ71_USBDETECT_GPIO);
- if (request_irq(gpio_to_irq(PALMZ71_USBDETECT_GPIO),
- palmz71_powercable, 0, "palmz71-cable", NULL))
- printk(KERN_ERR
- "IRQ request for power cable failed!\n");
- palmz71_powercable(gpio_to_irq(PALMZ71_USBDETECT_GPIO), NULL);
- }
-}
-
-static void __init
-omap_palmz71_init(void)
-{
- /* mux pins for uarts */
- omap_cfg_reg(UART1_TX);
- omap_cfg_reg(UART1_RTS);
- omap_cfg_reg(UART2_TX);
- omap_cfg_reg(UART2_RTS);
- omap_cfg_reg(UART3_TX);
- omap_cfg_reg(UART3_RX);
-
- palmz71_gpio_setup(1);
- omap_mpu_wdt_mode(0);
-
- platform_add_devices(devices, ARRAY_SIZE(devices));
-
- palmz71_boardinfo[0].irq = gpio_to_irq(PALMZ71_PENIRQ_GPIO);
- spi_register_board_info(palmz71_boardinfo,
- ARRAY_SIZE(palmz71_boardinfo));
- omap1_usb_init(&palmz71_usb_config);
- omap_serial_init();
- omap_register_i2c_bus(1, 100, NULL, 0);
- palmz71_gpio_setup(0);
-
- omapfb_set_lcd_config(&palmz71_lcd_config);
-}
-
-MACHINE_START(OMAP_PALMZ71, "OMAP310 based Palm Zire71")
- .atag_offset = 0x100,
- .map_io = omap15xx_map_io,
- .init_early = omap1_init_early,
- .init_irq = omap1_init_irq,
- .handle_irq = omap1_handle_irq,
- .init_machine = omap_palmz71_init,
- .init_late = omap1_init_late,
- .init_time = omap1_timer_init,
- .restart = omap1_restart,
-MACHINE_END
deleted file mode 100644
@@ -1,333 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-omap1/board-perseus2.c
- *
- * Modified from board-generic.c
- *
- * Original OMAP730 support by Jean Pihet <j-pihet@ti.com>
- * Updated for 2.6 by Kevin Hilman <kjh@hilman.org>
- */
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/platnand.h>
-#include <linux/mtd/physmap.h>
-#include <linux/input.h>
-#include <linux/smc91x.h>
-#include <linux/omapfb.h>
-#include <linux/platform_data/keypad-omap.h>
-#include <linux/soc/ti/omap1-io.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "tc.h"
-#include "mux.h"
-#include "flash.h"
-#include "hardware.h"
-#include "iomap.h"
-#include "common.h"
-#include "fpga.h"
-
-static const unsigned int p2_keymap[] = {
- KEY(0, 0, KEY_UP),
- KEY(1, 0, KEY_RIGHT),
- KEY(2, 0, KEY_LEFT),
- KEY(3, 0, KEY_DOWN),
- KEY(4, 0, KEY_ENTER),
- KEY(0, 1, KEY_F10),
- KEY(1, 1, KEY_SEND),
- KEY(2, 1, KEY_END),
- KEY(3, 1, KEY_VOLUMEDOWN),
- KEY(4, 1, KEY_VOLUMEUP),
- KEY(5, 1, KEY_RECORD),
- KEY(0, 2, KEY_F9),
- KEY(1, 2, KEY_3),
- KEY(2, 2, KEY_6),
- KEY(3, 2, KEY_9),
- KEY(4, 2, KEY_KPDOT),
- KEY(0, 3, KEY_BACK),
- KEY(1, 3, KEY_2),
- KEY(2, 3, KEY_5),
- KEY(3, 3, KEY_8),
- KEY(4, 3, KEY_0),
- KEY(5, 3, KEY_KPSLASH),
- KEY(0, 4, KEY_HOME),
- KEY(1, 4, KEY_1),
- KEY(2, 4, KEY_4),
- KEY(3, 4, KEY_7),
- KEY(4, 4, KEY_KPASTERISK),
- KEY(5, 4, KEY_POWER),
-};
-
-static struct smc91x_platdata smc91x_info = {
- .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
- .leda = RPC_LED_100_10,
- .ledb = RPC_LED_TX_RX,
-};
-
-static struct resource smc91x_resources[] = {
- [0] = {
- .start = H2P2_DBG_FPGA_ETHR_START, /* Physical */
- .end = H2P2_DBG_FPGA_ETHR_START + 0xf,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = INT_7XX_MPU_EXT_NIRQ,
- .end = 0,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
- },
-};
-
-static struct mtd_partition nor_partitions[] = {
- /* bootloader (U-Boot, etc) in first sector */
- {
- .name = "bootloader",
- .offset = 0,
- .size = SZ_128K,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- /* bootloader params in the next sector */
- {
- .name = "params",
- .offset = MTDPART_OFS_APPEND,
- .size = SZ_128K,
- .mask_flags = 0,
- },
- /* kernel */
- {
- .name = "kernel",
- .offset = MTDPART_OFS_APPEND,
- .size = SZ_2M,
- .mask_flags = 0
- },
- /* rest of flash is a file system */
- {
- .name = "rootfs",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL,
- .mask_flags = 0
- },
-};
-
-static struct physmap_flash_data nor_data = {
- .width = 2,
- .set_vpp = omap1_set_vpp,
- .parts = nor_partitions,
- .nr_parts = ARRAY_SIZE(nor_partitions),
-};
-
-static struct resource nor_resource = {
- .start = OMAP_CS0_PHYS,
- .end = OMAP_CS0_PHYS + SZ_32M - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device nor_device = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &nor_data,
- },
- .num_resources = 1,
- .resource = &nor_resource,
-};
-
-#define P2_NAND_RB_GPIO_PIN 62
-
-static int nand_dev_ready(struct nand_chip *chip)
-{
- return gpio_get_value(P2_NAND_RB_GPIO_PIN);
-}
-
-static struct platform_nand_data nand_data = {
- .chip = {
- .nr_chips = 1,
- .chip_offset = 0,
- .options = NAND_SAMSUNG_LP_OPTIONS,
- },
- .ctrl = {
- .cmd_ctrl = omap1_nand_cmd_ctl,
- .dev_ready = nand_dev_ready,
- },
-};
-
-static struct resource nand_resource = {
- .start = OMAP_CS3_PHYS,
- .end = OMAP_CS3_PHYS + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device nand_device = {
- .name = "gen_nand",
- .id = 0,
- .dev = {
- .platform_data = &nand_data,
- },
- .num_resources = 1,
- .resource = &nand_resource,
-};
-
-static struct platform_device smc91x_device = {
- .name = "smc91x",
- .id = 0,
- .dev = {
- .platform_data = &smc91x_info,
- },
- .num_resources = ARRAY_SIZE(smc91x_resources),
- .resource = smc91x_resources,
-};
-
-static struct resource kp_resources[] = {
- [0] = {
- .start = INT_7XX_MPUIO_KEYPAD,
- .end = INT_7XX_MPUIO_KEYPAD,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static const struct matrix_keymap_data p2_keymap_data = {
- .keymap = p2_keymap,
- .keymap_size = ARRAY_SIZE(p2_keymap),
-};
-
-static struct omap_kp_platform_data kp_data = {
- .rows = 8,
- .cols = 8,
- .keymap_data = &p2_keymap_data,
- .delay = 4,
- .dbounce = true,
-};
-
-static struct platform_device kp_device = {
- .name = "omap-keypad",
- .id = -1,
- .dev = {
- .platform_data = &kp_data,
- },
- .num_resources = ARRAY_SIZE(kp_resources),
- .resource = kp_resources,
-};
-
-static struct platform_device *devices[] __initdata = {
- &nor_device,
- &nand_device,
- &smc91x_device,
- &kp_device,
-};
-
-static const struct omap_lcd_config perseus2_lcd_config __initconst = {
- .ctrl_name = "internal",
-};
-
-static void __init perseus2_init_smc91x(void)
-{
- __raw_writeb(1, H2P2_DBG_FPGA_LAN_RESET);
- mdelay(50);
- __raw_writeb(__raw_readb(H2P2_DBG_FPGA_LAN_RESET) & ~1,
- H2P2_DBG_FPGA_LAN_RESET);
- mdelay(50);
-}
-
-static void __init omap_perseus2_init(void)
-{
- /* Early, board-dependent init */
-
- /*
- * Hold GSM Reset until needed
- */
- omap_writew(omap_readw(OMAP7XX_DSP_M_CTL) & ~1, OMAP7XX_DSP_M_CTL);
-
- /*
- * UARTs -> done automagically by 8250 driver
- */
-
- /*
- * CSx timings, GPIO Mux ... setup
- */
-
- /* Flash: CS0 timings setup */
- omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_0);
- omap_writel(0x00000088, OMAP7XX_FLASH_ACFG_0);
-
- /*
- * Ethernet support through the debug board
- * CS1 timings setup
- */
- omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_1);
- omap_writel(0x00000000, OMAP7XX_FLASH_ACFG_1);
-
- /*
- * Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
- * It is used as the Ethernet controller interrupt
- */
- omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF,
- OMAP7XX_IO_CONF_9);
-
- perseus2_init_smc91x();
-
- BUG_ON(gpio_request(P2_NAND_RB_GPIO_PIN, "NAND ready") < 0);
- gpio_direction_input(P2_NAND_RB_GPIO_PIN);
-
- omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
- omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
-
- /* Mux pins for keypad */
- omap_cfg_reg(E2_7XX_KBR0);
- omap_cfg_reg(J7_7XX_KBR1);
- omap_cfg_reg(E1_7XX_KBR2);
- omap_cfg_reg(F3_7XX_KBR3);
- omap_cfg_reg(D2_7XX_KBR4);
- omap_cfg_reg(C2_7XX_KBC0);
- omap_cfg_reg(D3_7XX_KBC1);
- omap_cfg_reg(E4_7XX_KBC2);
- omap_cfg_reg(F4_7XX_KBC3);
- omap_cfg_reg(E3_7XX_KBC4);
-
- if (IS_ENABLED(CONFIG_SPI_OMAP_UWIRE)) {
- /* configure pins: MPU_UW_nSCS1, MPU_UW_SDO, MPU_UW_SCLK */
- int val = omap_readl(OMAP7XX_IO_CONF_9) & ~0x00EEE000;
- omap_writel(val | 0x00AAA000, OMAP7XX_IO_CONF_9);
- }
-
- platform_add_devices(devices, ARRAY_SIZE(devices));
-
- omap_serial_init();
- omap_register_i2c_bus(1, 100, NULL, 0);
-
- omapfb_set_lcd_config(&perseus2_lcd_config);
-}
-
-/* Only FPGA needs to be mapped here. All others are done with ioremap */
-static struct map_desc omap_perseus2_io_desc[] __initdata = {
- {
- .virtual = H2P2_DBG_FPGA_BASE,
- .pfn = __phys_to_pfn(H2P2_DBG_FPGA_START),
- .length = H2P2_DBG_FPGA_SIZE,
- .type = MT_DEVICE
- }
-};
-
-static void __init omap_perseus2_map_io(void)
-{
- omap7xx_map_io();
- iotable_init(omap_perseus2_io_desc,
- ARRAY_SIZE(omap_perseus2_io_desc));
-}
-
-MACHINE_START(OMAP_PERSEUS2, "OMAP730 Perseus2")
- /* Maintainer: Kevin Hilman <kjh@hilman.org> */
- .atag_offset = 0x100,
- .map_io = omap_perseus2_map_io,
- .init_early = omap1_init_early,
- .init_irq = omap1_init_irq,
- .handle_irq = omap1_handle_irq,
- .init_machine = omap_perseus2_init,
- .init_late = omap1_init_late,
- .init_time = omap1_timer_init,
- .restart = omap1_restart,
-MACHINE_END
deleted file mode 100644
@@ -1,186 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-omap1/fpga.c
- *
- * Interrupt handler for OMAP-1510 Innovator FPGA
- *
- * Copyright (C) 2001 RidgeRun, Inc.
- * Author: Greg Lonnon <glonnon@ridgerun.com>
- *
- * Copyright (C) 2002 MontaVista Software, Inc.
- *
- * Separated FPGA interrupts from innovator1510.c and cleaned up for 2.6
- * Copyright (C) 2004 Nokia Corporation by Tony Lindrgen <tony@atomide.com>
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/device.h>
-#include <linux/errno.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <asm/mach/irq.h>
-
-#include "hardware.h"
-#include "iomap.h"
-#include "common.h"
-#include "fpga.h"
-
-static void fpga_mask_irq(struct irq_data *d)
-{
- unsigned int irq = d->irq - OMAP_FPGA_IRQ_BASE;
-
- if (irq < 8)
- __raw_writeb((__raw_readb(OMAP1510_FPGA_IMR_LO)
- & ~(1 << irq)), OMAP1510_FPGA_IMR_LO);
- else if (irq < 16)
- __raw_writeb((__raw_readb(OMAP1510_FPGA_IMR_HI)
- & ~(1 << (irq - 8))), OMAP1510_FPGA_IMR_HI);
- else
- __raw_writeb((__raw_readb(INNOVATOR_FPGA_IMR2)
- & ~(1 << (irq - 16))), INNOVATOR_FPGA_IMR2);
-}
-
-
-static inline u32 get_fpga_unmasked_irqs(void)
-{
- return
- ((__raw_readb(OMAP1510_FPGA_ISR_LO) &
- __raw_readb(OMAP1510_FPGA_IMR_LO))) |
- ((__raw_readb(OMAP1510_FPGA_ISR_HI) &
- __raw_readb(OMAP1510_FPGA_IMR_HI)) << 8) |
- ((__raw_readb(INNOVATOR_FPGA_ISR2) &
- __raw_readb(INNOVATOR_FPGA_IMR2)) << 16);
-}
-
-
-static void fpga_ack_irq(struct irq_data *d)
-{
- /* Don't need to explicitly ACK FPGA interrupts */
-}
-
-static void fpga_unmask_irq(struct irq_data *d)
-{
- unsigned int irq = d->irq - OMAP_FPGA_IRQ_BASE;
-
- if (irq < 8)
- __raw_writeb((__raw_readb(OMAP1510_FPGA_IMR_LO) | (1 << irq)),
- OMAP1510_FPGA_IMR_LO);
- else if (irq < 16)
- __raw_writeb((__raw_readb(OMAP1510_FPGA_IMR_HI)
- | (1 << (irq - 8))), OMAP1510_FPGA_IMR_HI);
- else
- __raw_writeb((__raw_readb(INNOVATOR_FPGA_IMR2)
- | (1 << (irq - 16))), INNOVATOR_FPGA_IMR2);
-}
-
-static void fpga_mask_ack_irq(struct irq_data *d)
-{
- fpga_mask_irq(d);
- fpga_ack_irq(d);
-}
-
-static void innovator_fpga_IRQ_demux(struct irq_desc *desc)
-{
- u32 stat;
- int fpga_irq;
-
- stat = get_fpga_unmasked_irqs();
-
- if (!stat)
- return;
-
- for (fpga_irq = OMAP_FPGA_IRQ_BASE;
- (fpga_irq < OMAP_FPGA_IRQ_END) && stat;
- fpga_irq++, stat >>= 1) {
- if (stat & 1) {
- generic_handle_irq(fpga_irq);
- }
- }
-}
-
-static struct irq_chip omap_fpga_irq_ack = {
- .name = "FPGA-ack",
- .irq_ack = fpga_mask_ack_irq,
- .irq_mask = fpga_mask_irq,
- .irq_unmask = fpga_unmask_irq,
-};
-
-
-static struct irq_chip omap_fpga_irq = {
- .name = "FPGA",
- .irq_ack = fpga_ack_irq,
- .irq_mask = fpga_mask_irq,
- .irq_unmask = fpga_unmask_irq,
-};
-
-/*
- * All of the FPGA interrupt request inputs except for the touchscreen are
- * edge-sensitive; the touchscreen is level-sensitive. The edge-sensitive
- * interrupts are acknowledged as a side-effect of reading the interrupt
- * status register from the FPGA. The edge-sensitive interrupt inputs
- * cause a problem with level interrupt requests, such as Ethernet. The
- * problem occurs when a level interrupt request is asserted while its
- * interrupt input is masked in the FPGA, which results in a missed
- * interrupt.
- *
- * In an attempt to workaround the problem with missed interrupts, the
- * mask_ack routine for all of the FPGA interrupts has been changed from
- * fpga_mask_ack_irq() to fpga_ack_irq() so that the specific FPGA interrupt
- * being serviced is left unmasked. We can do this because the FPGA cascade
- * interrupt is run with all interrupts masked.
- *
- * Limited testing indicates that this workaround appears to be effective
- * for the smc9194 Ethernet driver used on the Innovator. It should work
- * on other FPGA interrupts as well, but any drivers that explicitly mask
- * interrupts at the interrupt controller via disable_irq/enable_irq
- * could pose a problem.
- */
-void omap1510_fpga_init_irq(void)
-{
- int i, res;
-
- __raw_writeb(0, OMAP1510_FPGA_IMR_LO);
- __raw_writeb(0, OMAP1510_FPGA_IMR_HI);
- __raw_writeb(0, INNOVATOR_FPGA_IMR2);
-
- for (i = OMAP_FPGA_IRQ_BASE; i < OMAP_FPGA_IRQ_END; i++) {
-
- if (i == OMAP1510_INT_FPGA_TS) {
- /*
- * The touchscreen interrupt is level-sensitive, so
- * we'll use the regular mask_ack routine for it.
- */
- irq_set_chip(i, &omap_fpga_irq_ack);
- }
- else {
- /*
- * All FPGA interrupts except the touchscreen are
- * edge-sensitive, so we won't mask them.
- */
- irq_set_chip(i, &omap_fpga_irq);
- }
-
- irq_set_handler(i, handle_edge_irq);
- irq_clear_status_flags(i, IRQ_NOREQUEST);
- }
-
- /*
- * The FPGA interrupt line is connected to GPIO13. Claim this pin for
- * the ARM.
- *
- * NOTE: For general GPIO/MPUIO access and interrupts, please see
- * gpio.[ch]
- */
- res = gpio_request(13, "FPGA irq");
- if (res) {
- pr_err("%s failed to get gpio\n", __func__);
- return;
- }
- gpio_direction_input(13);
- irq_set_irq_type(gpio_to_irq(13), IRQ_TYPE_EDGE_RISING);
- irq_set_chained_handler(OMAP1510_INT_FPGA, innovator_fpga_IRQ_demux);
-}
deleted file mode 100644
@@ -1,49 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Interrupt handler for OMAP-1510 FPGA
- *
- * Copyright (C) 2001 RidgeRun, Inc.
- * Author: Greg Lonnon <glonnon@ridgerun.com>
- *
- * Copyright (C) 2002 MontaVista Software, Inc.
- *
- * Separated FPGA interrupts from innovator1510.c and cleaned up for 2.6
- * Copyright (C) 2004 Nokia Corporation by Tony Lindrgen <tony@atomide.com>
- */
-
-#ifndef __ASM_ARCH_OMAP_FPGA_H
-#define __ASM_ARCH_OMAP_FPGA_H
-
-/*
- * ---------------------------------------------------------------------------
- * H2/P2 Debug board FPGA
- * ---------------------------------------------------------------------------
- */
-/* maps in the FPGA registers and the ETHR registers */
-#define H2P2_DBG_FPGA_BASE 0xE8000000 /* VA */
-#define H2P2_DBG_FPGA_SIZE SZ_4K /* SIZE */
-#define H2P2_DBG_FPGA_START 0x04000000 /* PA */
-
-#define H2P2_DBG_FPGA_ETHR_START (H2P2_DBG_FPGA_START + 0x300)
-#define H2P2_DBG_FPGA_FPGA_REV IOMEM(H2P2_DBG_FPGA_BASE + 0x10) /* FPGA Revision */
-#define H2P2_DBG_FPGA_BOARD_REV IOMEM(H2P2_DBG_FPGA_BASE + 0x12) /* Board Revision */
-#define H2P2_DBG_FPGA_GPIO IOMEM(H2P2_DBG_FPGA_BASE + 0x14) /* GPIO outputs */
-#define H2P2_DBG_FPGA_LEDS IOMEM(H2P2_DBG_FPGA_BASE + 0x16) /* LEDs outputs */
-#define H2P2_DBG_FPGA_MISC_INPUTS IOMEM(H2P2_DBG_FPGA_BASE + 0x18) /* Misc inputs */
-#define H2P2_DBG_FPGA_LAN_STATUS IOMEM(H2P2_DBG_FPGA_BASE + 0x1A) /* LAN Status line */
-#define H2P2_DBG_FPGA_LAN_RESET IOMEM(H2P2_DBG_FPGA_BASE + 0x1C) /* LAN Reset line */
-
-/* LEDs definition on debug board (16 LEDs, all physically green) */
-#define H2P2_DBG_FPGA_LED_GREEN (1 << 15)
-#define H2P2_DBG_FPGA_LED_AMBER (1 << 14)
-#define H2P2_DBG_FPGA_LED_RED (1 << 13)
-#define H2P2_DBG_FPGA_LED_BLUE (1 << 12)
-/* cpu0 load-meter LEDs */
-#define H2P2_DBG_FPGA_LOAD_METER (1 << 0) // A bit of fun on our board ...
-#define H2P2_DBG_FPGA_LOAD_METER_SIZE 11
-#define H2P2_DBG_FPGA_LOAD_METER_MASK ((1 << H2P2_DBG_FPGA_LOAD_METER_SIZE) - 1)
-
-#define H2P2_DBG_FPGA_P2_LED_TIMER (1 << 0)
-#define H2P2_DBG_FPGA_P2_LED_IDLE (1 << 1)
-
-#endif
deleted file mode 100644
@@ -1,272 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * OMAP7xx specific gpio init
- *
- * Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com/
- *
- * Author:
- * Charulatha V <charu@ti.com>
- */
-
-#include <linux/gpio.h>
-#include <linux/platform_data/gpio-omap.h>
-
-#include "irqs.h"
-#include "soc.h"
-
-#define OMAP7XX_GPIO1_BASE 0xfffbc000
-#define OMAP7XX_GPIO2_BASE 0xfffbc800
-#define OMAP7XX_GPIO3_BASE 0xfffbd000
-#define OMAP7XX_GPIO4_BASE 0xfffbd800
-#define OMAP7XX_GPIO5_BASE 0xfffbe000
-#define OMAP7XX_GPIO6_BASE 0xfffbe800
-#define OMAP1_MPUIO_VBASE OMAP1_MPUIO_BASE
-
-/* mpu gpio */
-static struct resource omap7xx_mpu_gpio_resources[] = {
- {
- .start = OMAP1_MPUIO_VBASE,
- .end = OMAP1_MPUIO_VBASE + SZ_2K - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = INT_7XX_MPUIO,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct omap_gpio_reg_offs omap7xx_mpuio_regs = {
- .revision = USHRT_MAX,
- .direction = OMAP_MPUIO_IO_CNTL / 2,
- .datain = OMAP_MPUIO_INPUT_LATCH / 2,
- .dataout = OMAP_MPUIO_OUTPUT / 2,
- .irqstatus = OMAP_MPUIO_GPIO_INT / 2,
- .irqenable = OMAP_MPUIO_GPIO_MASKIT / 2,
- .irqenable_inv = true,
- .irqctrl = OMAP_MPUIO_GPIO_INT_EDGE >> 1,
-};
-
-static struct omap_gpio_platform_data omap7xx_mpu_gpio_config = {
- .is_mpuio = true,
- .bank_width = 16,
- .bank_stride = 2,
- .regs = &omap7xx_mpuio_regs,
-};
-
-static struct platform_device omap7xx_mpu_gpio = {
- .name = "omap_gpio",
- .id = 0,
- .dev = {
- .platform_data = &omap7xx_mpu_gpio_config,
- },
- .num_resources = ARRAY_SIZE(omap7xx_mpu_gpio_resources),
- .resource = omap7xx_mpu_gpio_resources,
-};
-
-/* gpio1 */
-static struct resource omap7xx_gpio1_resources[] = {
- {
- .start = OMAP7XX_GPIO1_BASE,
- .end = OMAP7XX_GPIO1_BASE + SZ_2K - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = INT_7XX_GPIO_BANK1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct omap_gpio_reg_offs omap7xx_gpio_regs = {
- .revision = USHRT_MAX,
- .direction = OMAP7XX_GPIO_DIR_CONTROL,
- .datain = OMAP7XX_GPIO_DATA_INPUT,
- .dataout = OMAP7XX_GPIO_DATA_OUTPUT,
- .irqstatus = OMAP7XX_GPIO_INT_STATUS,
- .irqenable = OMAP7XX_GPIO_INT_MASK,
- .irqenable_inv = true,
- .irqctrl = OMAP7XX_GPIO_INT_CONTROL,
-};
-
-static struct omap_gpio_platform_data omap7xx_gpio1_config = {
- .bank_width = 32,
- .regs = &omap7xx_gpio_regs,
-};
-
-static struct platform_device omap7xx_gpio1 = {
- .name = "omap_gpio",
- .id = 1,
- .dev = {
- .platform_data = &omap7xx_gpio1_config,
- },
- .num_resources = ARRAY_SIZE(omap7xx_gpio1_resources),
- .resource = omap7xx_gpio1_resources,
-};
-
-/* gpio2 */
-static struct resource omap7xx_gpio2_resources[] = {
- {
- .start = OMAP7XX_GPIO2_BASE,
- .end = OMAP7XX_GPIO2_BASE + SZ_2K - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = INT_7XX_GPIO_BANK2,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct omap_gpio_platform_data omap7xx_gpio2_config = {
- .bank_width = 32,
- .regs = &omap7xx_gpio_regs,
-};
-
-static struct platform_device omap7xx_gpio2 = {
- .name = "omap_gpio",
- .id = 2,
- .dev = {
- .platform_data = &omap7xx_gpio2_config,
- },
- .num_resources = ARRAY_SIZE(omap7xx_gpio2_resources),
- .resource = omap7xx_gpio2_resources,
-};
-
-/* gpio3 */
-static struct resource omap7xx_gpio3_resources[] = {
- {
- .start = OMAP7XX_GPIO3_BASE,
- .end = OMAP7XX_GPIO3_BASE + SZ_2K - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = INT_7XX_GPIO_BANK3,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct omap_gpio_platform_data omap7xx_gpio3_config = {
- .bank_width = 32,
- .regs = &omap7xx_gpio_regs,
-};
-
-static struct platform_device omap7xx_gpio3 = {
- .name = "omap_gpio",
- .id = 3,
- .dev = {
- .platform_data = &omap7xx_gpio3_config,
- },
- .num_resources = ARRAY_SIZE(omap7xx_gpio3_resources),
- .resource = omap7xx_gpio3_resources,
-};
-
-/* gpio4 */
-static struct resource omap7xx_gpio4_resources[] = {
- {
- .start = OMAP7XX_GPIO4_BASE,
- .end = OMAP7XX_GPIO4_BASE + SZ_2K - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = INT_7XX_GPIO_BANK4,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct omap_gpio_platform_data omap7xx_gpio4_config = {
- .bank_width = 32,
- .regs = &omap7xx_gpio_regs,
-};
-
-static struct platform_device omap7xx_gpio4 = {
- .name = "omap_gpio",
- .id = 4,
- .dev = {
- .platform_data = &omap7xx_gpio4_config,
- },
- .num_resources = ARRAY_SIZE(omap7xx_gpio4_resources),
- .resource = omap7xx_gpio4_resources,
-};
-
-/* gpio5 */
-static struct resource omap7xx_gpio5_resources[] = {
- {
- .start = OMAP7XX_GPIO5_BASE,
- .end = OMAP7XX_GPIO5_BASE + SZ_2K - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = INT_7XX_GPIO_BANK5,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct omap_gpio_platform_data omap7xx_gpio5_config = {
- .bank_width = 32,
- .regs = &omap7xx_gpio_regs,
-};
-
-static struct platform_device omap7xx_gpio5 = {
- .name = "omap_gpio",
- .id = 5,
- .dev = {
- .platform_data = &omap7xx_gpio5_config,
- },
- .num_resources = ARRAY_SIZE(omap7xx_gpio5_resources),
- .resource = omap7xx_gpio5_resources,
-};
-
-/* gpio6 */
-static struct resource omap7xx_gpio6_resources[] = {
- {
- .start = OMAP7XX_GPIO6_BASE,
- .end = OMAP7XX_GPIO6_BASE + SZ_2K - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = INT_7XX_GPIO_BANK6,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct omap_gpio_platform_data omap7xx_gpio6_config = {
- .bank_width = 32,
- .regs = &omap7xx_gpio_regs,
-};
-
-static struct platform_device omap7xx_gpio6 = {
- .name = "omap_gpio",
- .id = 6,
- .dev = {
- .platform_data = &omap7xx_gpio6_config,
- },
- .num_resources = ARRAY_SIZE(omap7xx_gpio6_resources),
- .resource = omap7xx_gpio6_resources,
-};
-
-static struct platform_device *omap7xx_gpio_dev[] __initdata = {
- &omap7xx_mpu_gpio,
- &omap7xx_gpio1,
- &omap7xx_gpio2,
- &omap7xx_gpio3,
- &omap7xx_gpio4,
- &omap7xx_gpio5,
- &omap7xx_gpio6,
-};
-
-/*
- * omap7xx_gpio_init needs to be done before
- * machine_init functions access gpio APIs.
- * Hence omap7xx_gpio_init is a postcore_initcall.
- */
-static int __init omap7xx_gpio_init(void)
-{
- int i;
-
- if (!cpu_is_omap7xx())
- return -EINVAL;
-
- for (i = 0; i < ARRAY_SIZE(omap7xx_gpio_dev); i++)
- platform_device_register(omap7xx_gpio_dev[i]);
-
- return 0;
-}
-postcore_initcall(omap7xx_gpio_init);
@@ -873,7 +873,7 @@ config I2C_OCORES
config I2C_OMAP
tristate "OMAP I2C adapter"
depends on ARCH_OMAP || ARCH_K3 || COMPILE_TEST
- default y if MACH_OMAP_H3 || MACH_OMAP_OSK
+ default MACH_OMAP_OSK
help
If you say yes to this option, support will be included for the
I2C interface on the Texas Instruments OMAP1/2 family of processors.
@@ -1524,7 +1524,7 @@ config TPS6105X
config TPS65010
tristate "TI TPS6501x Power Management chips"
depends on I2C && GPIOLIB
- default y if MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_OSK
+ default MACH_OMAP_OSK
help
If you say yes here you get support for the TPS6501x series of
Power Management chips. These include voltage regulators,
@@ -480,7 +480,7 @@ config MMC_SDHCI_ST
config MMC_OMAP
tristate "TI OMAP Multimedia Card Interface support"
depends on ARCH_OMAP
- depends on TPS65010 || !MACH_OMAP_H2
+ depends on TPS65010
help
This selects the TI OMAP Multimedia card Interface.
If you have an OMAP board with a Multimedia Card slot,
@@ -129,7 +129,7 @@ config USB_GR_UDC
config USB_OMAP
tristate "OMAP USB Device Controller"
depends on ARCH_OMAP1
- depends on ISP1301_OMAP || !(MACH_OMAP_H2 || MACH_OMAP_H3)
+ depends on ISP1301_OMAP
help
Many Texas Instruments OMAP processors have flexible full
speed USB device controllers, with support for up to 30
@@ -420,7 +420,7 @@ if USB_OHCI_HCD
config USB_OHCI_HCD_OMAP1
tristate "OHCI support for OMAP1/2 chips"
depends on ARCH_OMAP1
- depends on ISP1301_OMAP || !(MACH_OMAP_H2 || MACH_OMAP_H3)
+ depends on ISP1301_OMAP
default y
help
Enables support for the OHCI controller on OMAP1/2 chips.
deleted file mode 100644
@@ -1,19 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (C) 2006 Samsung Electronics
- * Kyungmin Park <kyungmin.park@samsung.com>
- */
-#ifndef ASMARM_ARCH_LED_H
-#define ASMARM_ARCH_LED_H
-
-struct omap_led_config {
- struct led_classdev cdev;
- s16 gpio;
-};
-
-struct omap_led_platform_data {
- s16 nr_leds;
- struct omap_led_config *leds;
-};
-
-#endif