| Message ID | 20221125234656.47306-5-samuel@sholland.org |
|---|---|
| State | Superseded |
| Headers | show |
| Series | riscv: Allwinner D1/D1s platform support | expand |
On Fri, Nov 25, 2022 at 05:46:48PM -0600, Samuel Holland wrote: > D1 (aka D1-H), D1s (aka F133), R528, and T113 are a family of SoCs based > on a single die, or at a pair of dies derived from the same design. > > D1 and D1s contain a single T-HEAD Xuantie C906 CPU, whereas R528 and > T113 contain a pair of Cortex-A7's. Is this "additionally contain" or a case of the D1 is the R528 but with s/arm/riscv/? It's the latter, right? > D1 and R528 are the full version of > the chip with a BGA package, whereas D1s and T113 are low-pin-count QFP > variants. > > Because the original design supported both ARM and RISC-V CPUs, some > peripherals are duplicated. In addition, all variants except D1s contain > a HiFi 4 DSP with its own set of peripherals. > > The devicetrees are organized to minimize duplication: > - Common perhiperals are described in sunxi-d1s-t113.dtsi > - DSP-related peripherals are described in sunxi-d1-t113.dtsi > - RISC-V specific hardware is described in sun20i-d1s.dtsi > - Functionality unique to the D1 variant is described in sun20i-d1.dtsi > > The SOC_PERIPHERAL_IRQ macro handles the different #interrupt-cells > values between the ARM (GIC) and RISC-V (PLIC) versions of the SoC. Modulo the warnings I replied to the cover with & one minor comment below: Reviewed-by: Conor Dooley <conor.dooley@microchip.com> > Signed-off-by: Samuel Holland <samuel@sholland.org> > --- > > Changes in v2: > - Split into separate files for sharing with D1s/R528/T113 > - Use SOC_PERIPHERAL_IRQ macro for interrupts > - Rename osc24M to dcxo and move the frequency to the board DTs > - Drop analog LDOs due to the missing binding > - Correct tcon_top DSI clock reference > - Add DMIC, DSI controller, and DPHY (bindings are in linux-next) > - Add CPU OPP table > > arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi | 66 ++ > arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi | 76 ++ > .../boot/dts/allwinner/sunxi-d1-t113.dtsi | 15 + > .../boot/dts/allwinner/sunxi-d1s-t113.dtsi | 844 ++++++++++++++++++ > 4 files changed, 1001 insertions(+) > create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi > create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi > create mode 100644 arch/riscv/boot/dts/allwinner/sunxi-d1-t113.dtsi > create mode 100644 arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi > diff --git a/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi b/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi > new file mode 100644 > index 000000000000..c8815cbf0b46 > --- /dev/null > +++ b/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi > @@ -0,0 +1,844 @@ > +// SPDX-License-Identifier: (GPL-2.0+ or MIT) > +// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org> > + > +#include <dt-bindings/clock/sun6i-rtc.h> > +#include <dt-bindings/clock/sun8i-de2.h> > +#include <dt-bindings/clock/sun8i-tcon-top.h> > +#include <dt-bindings/clock/sun20i-d1-ccu.h> > +#include <dt-bindings/clock/sun20i-d1-r-ccu.h> > +#include <dt-bindings/interrupt-controller/irq.h> > +#include <dt-bindings/reset/sun8i-de2.h> > +#include <dt-bindings/reset/sun20i-d1-ccu.h> > +#include <dt-bindings/reset/sun20i-d1-r-ccu.h> > + > +/ { > + #address-cells = <1>; > + #size-cells = <1>; > + > + dcxo: dcxo-clk { > + compatible = "fixed-clock"; > + /* This value must be overridden by the board */ > + clock-frequency = <0>; Since this is a "must", can you drop the clock-frequency = <0> here so that if someone doesn't override it in their board dt-validate complains? Thanks, Conor. > + clock-output-names = "dcxo"; > + #clock-cells = <0>; > + }; > +
On 11/27/22 11:41, Andre Przywara wrote: > On Fri, 25 Nov 2022 17:46:48 -0600 > Samuel Holland <samuel@sholland.org> wrote: > >> D1 (aka D1-H), D1s (aka F133), R528, and T113 are a family of SoCs based >> on a single die, or at a pair of dies derived from the same design. >> >> D1 and D1s contain a single T-HEAD Xuantie C906 CPU, whereas R528 and >> T113 contain a pair of Cortex-A7's. D1 and R528 are the full version of >> the chip with a BGA package, whereas D1s and T113 are low-pin-count QFP >> variants. >> >> Because the original design supported both ARM and RISC-V CPUs, some >> peripherals are duplicated. In addition, all variants except D1s contain >> a HiFi 4 DSP with its own set of peripherals. >> >> The devicetrees are organized to minimize duplication: >> - Common perhiperals are described in sunxi-d1s-t113.dtsi > > So I compared all the reg and interrupts properties against the T113 > manual, they match, as far as they are described there. The undocumented > rest matches what we already have in other SoCs. > > I noticed two things, though, mentioned inline below: > > [...] > >> + display_clocks: clock-controller@5000000 { > > The clocks and the two mixers are not children of a bus node anymore, > IIUC correctly this was to manage the SRAM control. Is that now handled > differently, or does the D1 generation not require this anymore? The D1 family uses the DSP SRAM for extra space during early boot -- this applies even to D1s, where the DSP is fused off. Since the DE SRAM is not used for this purpose, the "SRAM C" aka "boot mode" bit in the SRAM controller is cleared by default, thus mapping the DE SRAM to the peripheral. So the DE works without touching the syscon registers. However, if I set the SRAM C bit, the DE stops working. So having the bus node would make some sense. But I do not know any address for the SRAM -- there is no "boot" address, and the "peripheral" address may not even be accessible to the CPU. So it is not possible to represent this with a mmio-sram node like the binding requires. So I suppose we should either change the binding to allow a child allwinner,sun50i-a64-sram-c node with no address (the driver should work fine with this); or leave out the bus, and people who go poking around in the syscon registers get to keep the pieces. :) >> + compatible = "allwinner,sun20i-d1-de2-clk", >> + "allwinner,sun50i-h5-de2-clk"; >> + reg = <0x5000000 0x10000>; >> + clocks = <&ccu CLK_BUS_DE>, <&ccu CLK_DE>; >> + clock-names = "bus", "mod"; >> + resets = <&ccu RST_BUS_DE>; >> + #clock-cells = <1>; >> + #reset-cells = <1>; >> + }; >> + >> + mixer0: mixer@5100000 { >> + compatible = "allwinner,sun20i-d1-de2-mixer-0"; >> + reg = <0x5100000 0x100000>; >> + clocks = <&display_clocks CLK_BUS_MIXER0>, >> + <&display_clocks CLK_MIXER0>; >> + clock-names = "bus", "mod"; >> + resets = <&display_clocks RST_MIXER0>; >> + >> + ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + mixer0_out: port@1 { >> + reg = <1>; >> + >> + mixer0_out_tcon_top_mixer0: endpoint { >> + remote-endpoint = <&tcon_top_mixer0_in_mixer0>; >> + }; >> + }; >> + }; >> + }; >> + >> + mixer1: mixer@5200000 { >> + compatible = "allwinner,sun20i-d1-de2-mixer-1"; >> + reg = <0x5200000 0x100000>; >> + clocks = <&display_clocks CLK_BUS_MIXER1>, >> + <&display_clocks CLK_MIXER1>; >> + clock-names = "bus", "mod"; >> + resets = <&display_clocks RST_MIXER1>; >> + >> + ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + mixer1_out: port@1 { >> + reg = <1>; >> + >> + mixer1_out_tcon_top_mixer1: endpoint { >> + remote-endpoint = <&tcon_top_mixer1_in_mixer1>; >> + }; >> + }; >> + }; >> + }; >> + >> + dsi: dsi@5450000 { >> + compatible = "allwinner,sun20i-d1-mipi-dsi", >> + "allwinner,sun50i-a100-mipi-dsi"; >> + reg = <0x5450000 0x1000>; >> + interrupts = <SOC_PERIPHERAL_IRQ(92) IRQ_TYPE_LEVEL_HIGH>; >> + clocks = <&ccu CLK_BUS_MIPI_DSI>, >> + <&tcon_top CLK_TCON_TOP_DSI>; >> + clock-names = "bus", "mod"; >> + resets = <&ccu RST_BUS_MIPI_DSI>; >> + phys = <&dphy>; >> + phy-names = "dphy"; >> + status = "disabled"; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + port { >> + dsi_in_tcon_lcd0: endpoint { >> + remote-endpoint = <&tcon_lcd0_out_dsi>; >> + }; >> + }; >> + }; >> + >> + dphy: phy@5451000 { >> + compatible = "allwinner,sun20i-d1-mipi-dphy", >> + "allwinner,sun50i-a100-mipi-dphy"; >> + reg = <0x5451000 0x1000>; >> + interrupts = <SOC_PERIPHERAL_IRQ(92) IRQ_TYPE_LEVEL_HIGH>; > > This is the same interrupt number as for the DSI controller above. Is > that correct, and can the drivers handle that? Yes, it is correct. Currently, neither driver uses the interrupt, so we will just need to keep the sharing in mind if/when that happens. Regards, Samuel
在 2022-11-26星期六的 16:03 +0000，Conor Dooley写道： > On Fri, Nov 25, 2022 at 05:46:48PM -0600, Samuel Holland wrote: > > D1 (aka D1-H), D1s (aka F133), R528, and T113 are a family of SoCs > > based > > on a single die, or at a pair of dies derived from the same design. > > > > D1 and D1s contain a single T-HEAD Xuantie C906 CPU, whereas R528 > > and > > T113 contain a pair of Cortex-A7's. > > Is this "additionally contain" or a case of the D1 is the R528 but > with > s/arm/riscv/? It's the latter, right? Technically they're the same die, but the CPU cores are selectively enabled, and at least what Allwinner says is that D1 contains only RV and R528 contains only ARM. > > > D1 and R528 are the full version of > > the chip with a BGA package, whereas D1s and T113 are low-pin-count > > QFP > > variants. > > > > Because the original design supported both ARM and RISC-V CPUs, > > some > > peripherals are duplicated. In addition, all variants except D1s > > contain > > a HiFi 4 DSP with its own set of peripherals. > > > > The devicetrees are organized to minimize duplication: > > - Common perhiperals are described in sunxi-d1s-t113.dtsi > > - DSP-related peripherals are described in sunxi-d1-t113.dtsi > > - RISC-V specific hardware is described in sun20i-d1s.dtsi > > - Functionality unique to the D1 variant is described in sun20i- > > d1.dtsi > > > > The SOC_PERIPHERAL_IRQ macro handles the different #interrupt-cells > > values between the ARM (GIC) and RISC-V (PLIC) versions of the SoC. > > Modulo the warnings I replied to the cover with & one minor comment > below: > Reviewed-by: Conor Dooley <conor.dooley@microchip.com> > > > Signed-off-by: Samuel Holland <samuel@sholland.org> > > --- > > > > Changes in v2: > > - Split into separate files for sharing with D1s/R528/T113 > > - Use SOC_PERIPHERAL_IRQ macro for interrupts > > - Rename osc24M to dcxo and move the frequency to the board DTs > > - Drop analog LDOs due to the missing binding > > - Correct tcon_top DSI clock reference > > - Add DMIC, DSI controller, and DPHY (bindings are in linux-next) > > - Add CPU OPP table > > > > arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi | 66 ++ > > arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi | 76 ++ > > .../boot/dts/allwinner/sunxi-d1-t113.dtsi | 15 + > > .../boot/dts/allwinner/sunxi-d1s-t113.dtsi | 844 > > ++++++++++++++++++ > > 4 files changed, 1001 insertions(+) > > create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi > > create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi > > create mode 100644 arch/riscv/boot/dts/allwinner/sunxi-d1- > > t113.dtsi > > create mode 100644 arch/riscv/boot/dts/allwinner/sunxi-d1s- > > t113.dtsi > > > > diff --git a/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi > > b/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi > > new file mode 100644 > > index 000000000000..c8815cbf0b46 > > --- /dev/null > > +++ b/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi > > @@ -0,0 +1,844 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ or MIT) > > +// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org> > > + > > +#include <dt-bindings/clock/sun6i-rtc.h> > > +#include <dt-bindings/clock/sun8i-de2.h> > > +#include <dt-bindings/clock/sun8i-tcon-top.h> > > +#include <dt-bindings/clock/sun20i-d1-ccu.h> > > +#include <dt-bindings/clock/sun20i-d1-r-ccu.h> > > +#include <dt-bindings/interrupt-controller/irq.h> > > +#include <dt-bindings/reset/sun8i-de2.h> > > +#include <dt-bindings/reset/sun20i-d1-ccu.h> > > +#include <dt-bindings/reset/sun20i-d1-r-ccu.h> > > + > > +/ { > > + #address-cells = <1>; > > + #size-cells = <1>; > > + > > + dcxo: dcxo-clk { > > + compatible = "fixed-clock"; > > + /* This value must be overridden by the board */ > > + clock-frequency = <0>; > > Since this is a "must", can you drop the clock-frequency = <0> here > so > that if someone doesn't override it in their board dt-validate > complains? > > Thanks, > Conor. > > > + clock-output-names = "dcxo"; > > + #clock-cells = <0>; > > + }; > > + > >
在 2022-11-27星期日的 17:41 +0000，Andre Przywara写道： > On Fri, 25 Nov 2022 17:46:48 -0600 > Samuel Holland <samuel@sholland.org> wrote: > > > D1 (aka D1-H), D1s (aka F133), R528, and T113 are a family of SoCs > > based > > on a single die, or at a pair of dies derived from the same design. > > > > D1 and D1s contain a single T-HEAD Xuantie C906 CPU, whereas R528 > > and > > T113 contain a pair of Cortex-A7's. D1 and R528 are the full > > version of > > the chip with a BGA package, whereas D1s and T113 are low-pin-count > > QFP > > variants. > > > > Because the original design supported both ARM and RISC-V CPUs, > > some > > peripherals are duplicated. In addition, all variants except D1s > > contain > > a HiFi 4 DSP with its own set of peripherals. > > > > The devicetrees are organized to minimize duplication: > > - Common perhiperals are described in sunxi-d1s-t113.dtsi > > So I compared all the reg and interrupts properties against the T113 > manual, they match, as far as they are described there. The > undocumented > rest matches what we already have in other SoCs. > > I noticed two things, though, mentioned inline below: > > > - DSP-related peripherals are described in sunxi-d1-t113.dtsi > > - RISC-V specific hardware is described in sun20i-d1s.dtsi > > - Functionality unique to the D1 variant is described in sun20i- > > d1.dtsi > > > > The SOC_PERIPHERAL_IRQ macro handles the different #interrupt-cells > > values between the ARM (GIC) and RISC-V (PLIC) versions of the SoC. > > > > Signed-off-by: Samuel Holland <samuel@sholland.org> > > --- > > > > Changes in v2: > > - Split into separate files for sharing with D1s/R528/T113 > > - Use SOC_PERIPHERAL_IRQ macro for interrupts > > - Rename osc24M to dcxo and move the frequency to the board DTs > > - Drop analog LDOs due to the missing binding > > - Correct tcon_top DSI clock reference > > - Add DMIC, DSI controller, and DPHY (bindings are in linux-next) > > - Add CPU OPP table > > > > arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi | 66 ++ > > arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi | 76 ++ > > .../boot/dts/allwinner/sunxi-d1-t113.dtsi | 15 + > > .../boot/dts/allwinner/sunxi-d1s-t113.dtsi | 844 > > ++++++++++++++++++ > > 4 files changed, 1001 insertions(+) > > create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi > > create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi > > create mode 100644 arch/riscv/boot/dts/allwinner/sunxi-d1- > > t113.dtsi > > create mode 100644 arch/riscv/boot/dts/allwinner/sunxi-d1s- > > t113.dtsi > > > > diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi > > b/arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi > > new file mode 100644 > > index 000000000000..97e7cbb32597 > > --- /dev/null > > +++ b/arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi > > @@ -0,0 +1,66 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ or MIT) > > +// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org> > > + > > +#include "sun20i-d1s.dtsi" > > +#include "sunxi-d1-t113.dtsi" > > + > > +/ { > > + soc { > > + lradc: keys@2009800 { > > + compatible = "allwinner,sun20i-d1-lradc", > > + "allwinner,sun50i-r329-lradc"; > > + reg = <0x2009800 0x400>; > > + interrupts = <SOC_PERIPHERAL_IRQ(61) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_LRADC>; > > + resets = <&ccu RST_BUS_LRADC>; > > + status = "disabled"; > > + }; > > + > > + i2s0: i2s@2032000 { > > + compatible = "allwinner,sun20i-d1-i2s", > > + "allwinner,sun50i-r329-i2s"; > > + reg = <0x2032000 0x1000>; > > + interrupts = <SOC_PERIPHERAL_IRQ(26) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2S0>, > > + <&ccu CLK_I2S0>; > > + clock-names = "apb", "mod"; > > + resets = <&ccu RST_BUS_I2S0>; > > + dmas = <&dma 3>, <&dma 3>; > > + dma-names = "rx", "tx"; > > + status = "disabled"; > > + #sound-dai-cells = <0>; > > + }; > > + }; > > +}; > > + > > +&pio { > > + /omit-if-no-ref/ > > + dmic_pb11_d0_pin: dmic-pb11-d0-pin { > > + pins = "PB11"; > > + function = "dmic"; > > + }; > > + > > + /omit-if-no-ref/ > > + dmic_pe17_clk_pin: dmic-pe17-clk-pin { > > + pins = "PE17"; > > + function = "dmic"; > > + }; > > + > > + /omit-if-no-ref/ > > + i2c0_pb10_pins: i2c0-pb10-pins { > > + pins = "PB10", "PB11"; > > + function = "i2c0"; > > + }; > > + > > + /omit-if-no-ref/ > > + i2c2_pb0_pins: i2c2-pb0-pins { > > + pins = "PB0", "PB1"; > > + function = "i2c2"; > > + }; > > + > > + /omit-if-no-ref/ > > + uart0_pb8_pins: uart0-pb8-pins { > > + pins = "PB8", "PB9"; > > + function = "uart0"; > > + }; > > +}; > > diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi > > b/arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi > > new file mode 100644 > > index 000000000000..859509832d58 > > --- /dev/null > > +++ b/arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi > > @@ -0,0 +1,76 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ or MIT) > > +// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org> > > + > > +#define SOC_PERIPHERAL_IRQ(nr) (nr + 16) > > + > > +#include "sunxi-d1s-t113.dtsi" > > + > > +/ { > > + cpus { > > + timebase-frequency = <24000000>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + cpu0: cpu@0 { > > + compatible = "thead,c906", "riscv"; > > + device_type = "cpu"; > > + reg = <0>; > > + clocks = <&ccu CLK_RISCV>; > > + d-cache-block-size = <64>; > > + d-cache-sets = <256>; > > + d-cache-size = <32768>; > > + i-cache-block-size = <64>; > > + i-cache-sets = <128>; > > + i-cache-size = <32768>; > > + mmu-type = "riscv,sv39"; > > + operating-points-v2 = <&opp_table_cpu>; > > + riscv,isa = "rv64imafdc"; > > + #cooling-cells = <2>; > > + > > + cpu0_intc: interrupt-controller { > > + compatible = "riscv,cpu-intc"; > > + interrupt-controller; > > + #address-cells = <0>; > > + #interrupt-cells = <1>; > > + }; > > + }; > > + }; > > + > > + opp_table_cpu: opp-table-cpu { > > + compatible = "operating-points-v2"; > > + > > + opp-408000000 { > > + opp-hz = /bits/ 64 <408000000>; > > + opp-microvolt = <900000 900000 1100000>; > > + }; > > + > > + opp-1080000000 { > > + opp-hz = /bits/ 64 <1008000000>; > > + opp-microvolt = <900000 900000 1100000>; > > + }; > > + }; > > + > > + soc { > > + interrupt-parent = <&plic>; > > + > > + riscv_wdt: watchdog@6011000 { > > + compatible = "allwinner,sun20i-d1-wdt"; > > + reg = <0x6011000 0x20>; > > + interrupts = <SOC_PERIPHERAL_IRQ(131) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&dcxo>, <&rtc CLK_OSC32K>; > > + clock-names = "hosc", "losc"; > > + }; > > + > > + plic: interrupt-controller@10000000 { > > + compatible = "allwinner,sun20i-d1-plic", > > + "thead,c900-plic"; > > + reg = <0x10000000 0x4000000>; > > + interrupts-extended = <&cpu0_intc 11>, > > + <&cpu0_intc 9>; > > + interrupt-controller; > > + riscv,ndev = <176>; > > + #address-cells = <0>; > > + #interrupt-cells = <2>; > > + }; > > + }; > > +}; > > diff --git a/arch/riscv/boot/dts/allwinner/sunxi-d1-t113.dtsi > > b/arch/riscv/boot/dts/allwinner/sunxi-d1-t113.dtsi > > new file mode 100644 > > index 000000000000..b7156123df54 > > --- /dev/null > > +++ b/arch/riscv/boot/dts/allwinner/sunxi-d1-t113.dtsi > > @@ -0,0 +1,15 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ or MIT) > > +// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org> > > + > > +/ { > > + soc { > > + dsp_wdt: watchdog@1700400 { > > + compatible = "allwinner,sun20i-d1-wdt"; > > + reg = <0x1700400 0x20>; > > + interrupts = <SOC_PERIPHERAL_IRQ(122) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&dcxo>, <&rtc CLK_OSC32K>; > > + clock-names = "hosc", "losc"; > > + status = "reserved"; > > + }; > > + }; > > +}; > > diff --git a/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi > > b/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi > > new file mode 100644 > > index 000000000000..c8815cbf0b46 > > --- /dev/null > > +++ b/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi > > @@ -0,0 +1,844 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ or MIT) > > +// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org> > > + > > +#include <dt-bindings/clock/sun6i-rtc.h> > > +#include <dt-bindings/clock/sun8i-de2.h> > > +#include <dt-bindings/clock/sun8i-tcon-top.h> > > +#include <dt-bindings/clock/sun20i-d1-ccu.h> > > +#include <dt-bindings/clock/sun20i-d1-r-ccu.h> > > +#include <dt-bindings/interrupt-controller/irq.h> > > +#include <dt-bindings/reset/sun8i-de2.h> > > +#include <dt-bindings/reset/sun20i-d1-ccu.h> > > +#include <dt-bindings/reset/sun20i-d1-r-ccu.h> > > + > > +/ { > > + #address-cells = <1>; > > + #size-cells = <1>; > > + > > + dcxo: dcxo-clk { > > + compatible = "fixed-clock"; > > + /* This value must be overridden by the board */ > > + clock-frequency = <0>; > > + clock-output-names = "dcxo"; > > + #clock-cells = <0>; > > + }; > > + > > + de: display-engine { > > + compatible = "allwinner,sun20i-d1-display-engine"; > > + allwinner,pipelines = <&mixer0>, <&mixer1>; > > + status = "disabled"; > > + }; > > + > > + soc { > > + compatible = "simple-bus"; > > + ranges; > > + dma-noncoherent; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + > > + pio: pinctrl@2000000 { > > + compatible = "allwinner,sun20i-d1-pinctrl"; > > + reg = <0x2000000 0x800>; > > + interrupts = <SOC_PERIPHERAL_IRQ(69) > > IRQ_TYPE_LEVEL_HIGH>, > > + <SOC_PERIPHERAL_IRQ(71) > > IRQ_TYPE_LEVEL_HIGH>, > > + <SOC_PERIPHERAL_IRQ(73) > > IRQ_TYPE_LEVEL_HIGH>, > > + <SOC_PERIPHERAL_IRQ(75) > > IRQ_TYPE_LEVEL_HIGH>, > > + <SOC_PERIPHERAL_IRQ(77) > > IRQ_TYPE_LEVEL_HIGH>, > > + <SOC_PERIPHERAL_IRQ(79) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_APB0>, > > + <&dcxo>, > > + <&rtc CLK_OSC32K>; > > + clock-names = "apb", "hosc", "losc"; > > + gpio-controller; > > + interrupt-controller; > > + #gpio-cells = <3>; > > + #interrupt-cells = <3>; > > + > > + /omit-if-no-ref/ > > + clk_pg11_pin: clk-pg11-pin { > > + pins = "PG11"; > > + function = "clk"; > > + }; > > + > > + /omit-if-no-ref/ > > + dsi_4lane_pins: dsi-4lane-pins { > > + pins = "PD0", "PD1", "PD2", "PD3", > > "PD4", "PD5", > > + "PD6", "PD7", "PD8", "PD9"; > > + drive-strength = <30>; > > + function = "dsi"; > > + }; > > + > > + /omit-if-no-ref/ > > + lcd_rgb666_pins: lcd-rgb666-pins { > > + pins = "PD0", "PD1", "PD2", "PD3", > > "PD4", "PD5", > > + "PD6", "PD7", "PD8", "PD9", > > "PD10", "PD11", > > + "PD12", "PD13", "PD14", > > "PD15", "PD16", "PD17", > > + "PD18", "PD19", "PD20", > > "PD21"; > > + function = "lcd0"; > > + }; > > + > > + /omit-if-no-ref/ > > + mmc0_pins: mmc0-pins { > > + pins = "PF0", "PF1", "PF2", "PF3", > > "PF4", "PF5"; > > + function = "mmc0"; > > + }; > > + > > + /omit-if-no-ref/ > > + mmc1_pins: mmc1-pins { > > + pins = "PG0", "PG1", "PG2", "PG3", > > "PG4", "PG5"; > > + function = "mmc1"; > > + }; > > + > > + /omit-if-no-ref/ > > + mmc2_pins: mmc2-pins { > > + pins = "PC2", "PC3", "PC4", "PC5", > > "PC6", "PC7"; > > + function = "mmc2"; > > + }; > > + > > + /omit-if-no-ref/ > > + rgmii_pe_pins: rgmii-pe-pins { > > + pins = "PE0", "PE1", "PE2", "PE3", > > "PE4", > > + "PE5", "PE6", "PE7", "PE8", > > "PE9", > > + "PE11", "PE12", "PE13", > > "PE14", "PE15"; > > + function = "emac"; > > + }; > > + > > + /omit-if-no-ref/ > > + rmii_pe_pins: rmii-pe-pins { > > + pins = "PE0", "PE1", "PE2", "PE3", > > "PE4", > > + "PE5", "PE6", "PE7", "PE8", > > "PE9"; > > + function = "emac"; > > + }; > > + > > + /omit-if-no-ref/ > > + uart1_pg6_pins: uart1-pg6-pins { > > + pins = "PG6", "PG7"; > > + function = "uart1"; > > + }; > > + > > + /omit-if-no-ref/ > > + uart1_pg8_rts_cts_pins: uart1-pg8-rts-cts- > > pins { > > + pins = "PG8", "PG9"; > > + function = "uart1"; > > + }; > > + > > + /omit-if-no-ref/ > > + uart3_pb_pins: uart3-pb-pins { > > + pins = "PB6", "PB7"; > > + function = "uart3"; > > + }; > > + }; > > + > > + ccu: clock-controller@2001000 { > > + compatible = "allwinner,sun20i-d1-ccu"; > > + reg = <0x2001000 0x1000>; > > + clocks = <&dcxo>, > > + <&rtc CLK_OSC32K>, > > + <&rtc CLK_IOSC>; > > + clock-names = "hosc", "losc", "iosc"; > > + #clock-cells = <1>; > > + #reset-cells = <1>; > > + }; > > + > > + dmic: dmic@2031000 { > > + compatible = "allwinner,sun20i-d1-dmic", > > + "allwinner,sun50i-h6-dmic"; > > + reg = <0x2031000 0x400>; > > + interrupts = <SOC_PERIPHERAL_IRQ(24) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_DMIC>, > > + <&ccu CLK_DMIC>; > > + clock-names = "bus", "mod"; > > + resets = <&ccu RST_BUS_DMIC>; > > + dmas = <&dma 8>; > > + dma-names = "rx"; > > + status = "disabled"; > > + #sound-dai-cells = <0>; > > + }; > > + > > + i2s1: i2s@2033000 { > > + compatible = "allwinner,sun20i-d1-i2s", > > + "allwinner,sun50i-r329-i2s"; > > + reg = <0x2033000 0x1000>; > > + interrupts = <SOC_PERIPHERAL_IRQ(27) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2S1>, > > + <&ccu CLK_I2S1>; > > + clock-names = "apb", "mod"; > > + resets = <&ccu RST_BUS_I2S1>; > > + dmas = <&dma 4>, <&dma 4>; > > + dma-names = "rx", "tx"; > > + status = "disabled"; > > + #sound-dai-cells = <0>; > > + }; > > + > > + i2s2: i2s@2034000 { > > + compatible = "allwinner,sun20i-d1-i2s", > > + "allwinner,sun50i-r329-i2s"; > > + reg = <0x2034000 0x1000>; > > + interrupts = <SOC_PERIPHERAL_IRQ(28) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2S2>, > > + <&ccu CLK_I2S2>; > > + clock-names = "apb", "mod"; > > + resets = <&ccu RST_BUS_I2S2>; > > + dmas = <&dma 5>, <&dma 5>; > > + dma-names = "rx", "tx"; > > + status = "disabled"; > > + #sound-dai-cells = <0>; > > + }; > > + > > + timer: timer@2050000 { > > + compatible = "allwinner,sun20i-d1-timer", > > + "allwinner,sun8i-a23-timer"; > > + reg = <0x2050000 0xa0>; > > + interrupts = <SOC_PERIPHERAL_IRQ(59) > > IRQ_TYPE_LEVEL_HIGH>, > > + <SOC_PERIPHERAL_IRQ(60) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&dcxo>; > > + }; > > + > > + wdt: watchdog@20500a0 { > > + compatible = "allwinner,sun20i-d1-wdt- > > reset", > > + "allwinner,sun20i-d1-wdt"; > > + reg = <0x20500a0 0x20>; > > + interrupts = <SOC_PERIPHERAL_IRQ(63) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&dcxo>, <&rtc CLK_OSC32K>; > > + clock-names = "hosc", "losc"; > > + status = "reserved"; > > + }; > > + > > + uart0: serial@2500000 { > > + compatible = "snps,dw-apb-uart"; > > + reg = <0x2500000 0x400>; > > + reg-io-width = <4>; > > + reg-shift = <2>; > > + interrupts = <SOC_PERIPHERAL_IRQ(2) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_UART0>; > > + resets = <&ccu RST_BUS_UART0>; > > + dmas = <&dma 14>, <&dma 14>; > > + dma-names = "rx", "tx"; > > + status = "disabled"; > > + }; > > + > > + uart1: serial@2500400 { > > + compatible = "snps,dw-apb-uart"; > > + reg = <0x2500400 0x400>; > > + reg-io-width = <4>; > > + reg-shift = <2>; > > + interrupts = <SOC_PERIPHERAL_IRQ(3) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_UART1>; > > + resets = <&ccu RST_BUS_UART1>; > > + dmas = <&dma 15>, <&dma 15>; > > + dma-names = "rx", "tx"; > > + status = "disabled"; > > + }; > > + > > + uart2: serial@2500800 { > > + compatible = "snps,dw-apb-uart"; > > + reg = <0x2500800 0x400>; > > + reg-io-width = <4>; > > + reg-shift = <2>; > > + interrupts = <SOC_PERIPHERAL_IRQ(4) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_UART2>; > > + resets = <&ccu RST_BUS_UART2>; > > + dmas = <&dma 16>, <&dma 16>; > > + dma-names = "rx", "tx"; > > + status = "disabled"; > > + }; > > + > > + uart3: serial@2500c00 { > > + compatible = "snps,dw-apb-uart"; > > + reg = <0x2500c00 0x400>; > > + reg-io-width = <4>; > > + reg-shift = <2>; > > + interrupts = <SOC_PERIPHERAL_IRQ(5) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_UART3>; > > + resets = <&ccu RST_BUS_UART3>; > > + dmas = <&dma 17>, <&dma 17>; > > + dma-names = "rx", "tx"; > > + status = "disabled"; > > + }; > > + > > + uart4: serial@2501000 { > > + compatible = "snps,dw-apb-uart"; > > + reg = <0x2501000 0x400>; > > + reg-io-width = <4>; > > + reg-shift = <2>; > > + interrupts = <SOC_PERIPHERAL_IRQ(6) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_UART4>; > > + resets = <&ccu RST_BUS_UART4>; > > + dmas = <&dma 18>, <&dma 18>; > > + dma-names = "rx", "tx"; > > + status = "disabled"; > > + }; > > + > > + uart5: serial@2501400 { > > + compatible = "snps,dw-apb-uart"; > > + reg = <0x2501400 0x400>; > > + reg-io-width = <4>; > > + reg-shift = <2>; > > + interrupts = <SOC_PERIPHERAL_IRQ(7) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_UART5>; > > + resets = <&ccu RST_BUS_UART5>; > > + dmas = <&dma 19>, <&dma 19>; > > + dma-names = "rx", "tx"; > > + status = "disabled"; > > + }; > > + > > + i2c0: i2c@2502000 { > > + compatible = "allwinner,sun20i-d1-i2c", > > + "allwinner,sun8i-v536-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x2502000 0x400>; > > + interrupts = <SOC_PERIPHERAL_IRQ(9) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2C0>; > > + resets = <&ccu RST_BUS_I2C0>; > > + dmas = <&dma 43>, <&dma 43>; > > + dma-names = "rx", "tx"; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + i2c1: i2c@2502400 { > > + compatible = "allwinner,sun20i-d1-i2c", > > + "allwinner,sun8i-v536-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x2502400 0x400>; > > + interrupts = <SOC_PERIPHERAL_IRQ(10) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2C1>; > > + resets = <&ccu RST_BUS_I2C1>; > > + dmas = <&dma 44>, <&dma 44>; > > + dma-names = "rx", "tx"; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + i2c2: i2c@2502800 { > > + compatible = "allwinner,sun20i-d1-i2c", > > + "allwinner,sun8i-v536-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x2502800 0x400>; > > + interrupts = <SOC_PERIPHERAL_IRQ(11) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2C2>; > > + resets = <&ccu RST_BUS_I2C2>; > > + dmas = <&dma 45>, <&dma 45>; > > + dma-names = "rx", "tx"; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + i2c3: i2c@2502c00 { > > + compatible = "allwinner,sun20i-d1-i2c", > > + "allwinner,sun8i-v536-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x2502c00 0x400>; > > + interrupts = <SOC_PERIPHERAL_IRQ(12) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2C3>; > > + resets = <&ccu RST_BUS_I2C3>; > > + dmas = <&dma 46>, <&dma 46>; > > + dma-names = "rx", "tx"; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + syscon: syscon@3000000 { > > + compatible = "allwinner,sun20i-d1-system- > > control"; > > + reg = <0x3000000 0x1000>; > > + ranges; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + > > + regulators@3000150 { > > + compatible = "allwinner,sun20i-d1- > > system-ldos"; > > + reg = <0x3000150 0x4>; > > + > > + reg_ldoa: ldoa { > > + }; > > + > > + reg_ldob: ldob { > > + }; > > + }; > > + }; > > + > > + dma: dma-controller@3002000 { > > + compatible = "allwinner,sun20i-d1-dma"; > > + reg = <0x3002000 0x1000>; > > + interrupts = <SOC_PERIPHERAL_IRQ(50) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_DMA>, <&ccu > > CLK_MBUS_DMA>; > > + clock-names = "bus", "mbus"; > > + resets = <&ccu RST_BUS_DMA>; > > + dma-channels = <16>; > > + dma-requests = <48>; > > + #dma-cells = <1>; > > + }; > > + > > + sid: efuse@3006000 { > > + compatible = "allwinner,sun20i-d1-sid"; > > + reg = <0x3006000 0x1000>; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + }; > > + > > + mbus: dram-controller@3102000 { > > + compatible = "allwinner,sun20i-d1-mbus"; > > + reg = <0x3102000 0x1000>, > > + <0x3103000 0x1000>; > > + reg-names = "mbus", "dram"; > > + interrupts = <SOC_PERIPHERAL_IRQ(43) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_MBUS>, > > + <&ccu CLK_DRAM>, > > + <&ccu CLK_BUS_DRAM>; > > + clock-names = "mbus", "dram", "bus"; > > + dma-ranges = <0 0x40000000 0x80000000>; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + #interconnect-cells = <1>; > > + }; > > + > > + mmc0: mmc@4020000 { > > + compatible = "allwinner,sun20i-d1-mmc"; > > + reg = <0x4020000 0x1000>; > > + interrupts = <SOC_PERIPHERAL_IRQ(40) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_MMC0>, <&ccu > > CLK_MMC0>; > > + clock-names = "ahb", "mmc"; > > + resets = <&ccu RST_BUS_MMC0>; > > + reset-names = "ahb"; > > + cap-sd-highspeed; > > + max-frequency = <150000000>; > > + no-mmc; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + mmc1: mmc@4021000 { > > + compatible = "allwinner,sun20i-d1-mmc"; > > + reg = <0x4021000 0x1000>; > > + interrupts = <SOC_PERIPHERAL_IRQ(41) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_MMC1>, <&ccu > > CLK_MMC1>; > > + clock-names = "ahb", "mmc"; > > + resets = <&ccu RST_BUS_MMC1>; > > + reset-names = "ahb"; > > + cap-sd-highspeed; > > + max-frequency = <150000000>; > > + no-mmc; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + mmc2: mmc@4022000 { > > + compatible = "allwinner,sun20i-d1-emmc", > > + "allwinner,sun50i-a100-emmc"; > > + reg = <0x4022000 0x1000>; > > + interrupts = <SOC_PERIPHERAL_IRQ(42) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_MMC2>, <&ccu > > CLK_MMC2>; > > + clock-names = "ahb", "mmc"; > > + resets = <&ccu RST_BUS_MMC2>; > > + reset-names = "ahb"; > > + cap-mmc-highspeed; > > + max-frequency = <150000000>; > > + mmc-ddr-1_8v; > > + mmc-ddr-3_3v; > > + no-sd; > > + no-sdio; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + usb_otg: usb@4100000 { > > + compatible = "allwinner,sun20i-d1-musb", > > + "allwinner,sun8i-a33-musb"; > > + reg = <0x4100000 0x400>; > > + interrupts = <SOC_PERIPHERAL_IRQ(29) > > IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-names = "mc"; > > + clocks = <&ccu CLK_BUS_OTG>; > > + resets = <&ccu RST_BUS_OTG>; > > + extcon = <&usbphy 0>; > > + phys = <&usbphy 0>; > > + phy-names = "usb"; > > + status = "disabled"; > > + }; > > + > > + usbphy: phy@4100400 { > > + compatible = "allwinner,sun20i-d1-usb-phy"; > > + reg = <0x4100400 0x100>, > > + <0x4101800 0x100>, > > + <0x4200800 0x100>; > > + reg-names = "phy_ctrl", > > + "pmu0", > > + "pmu1"; > > + clocks = <&dcxo>, > > + <&dcxo>; > > + clock-names = "usb0_phy", > > + "usb1_phy"; > > + resets = <&ccu RST_USB_PHY0>, > > + <&ccu RST_USB_PHY1>; > > + reset-names = "usb0_reset", > > + "usb1_reset"; > > + status = "disabled"; > > + #phy-cells = <1>; > > + }; > > + > > + ehci0: usb@4101000 { > > + compatible = "allwinner,sun20i-d1-ehci", > > + "generic-ehci"; > > + reg = <0x4101000 0x100>; > > + interrupts = <SOC_PERIPHERAL_IRQ(30) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_OHCI0>, > > + <&ccu CLK_BUS_EHCI0>, > > + <&ccu CLK_USB_OHCI0>; > > + resets = <&ccu RST_BUS_OHCI0>, > > + <&ccu RST_BUS_EHCI0>; > > + phys = <&usbphy 0>; > > + phy-names = "usb"; > > + status = "disabled"; > > + }; > > + > > + ohci0: usb@4101400 { > > + compatible = "allwinner,sun20i-d1-ohci", > > + "generic-ohci"; > > + reg = <0x4101400 0x100>; > > + interrupts = <SOC_PERIPHERAL_IRQ(31) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_OHCI0>, > > + <&ccu CLK_USB_OHCI0>; > > + resets = <&ccu RST_BUS_OHCI0>; > > + phys = <&usbphy 0>; > > + phy-names = "usb"; > > + status = "disabled"; > > + }; > > + > > + ehci1: usb@4200000 { > > + compatible = "allwinner,sun20i-d1-ehci", > > + "generic-ehci"; > > + reg = <0x4200000 0x100>; > > + interrupts = <SOC_PERIPHERAL_IRQ(33) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_OHCI1>, > > + <&ccu CLK_BUS_EHCI1>, > > + <&ccu CLK_USB_OHCI1>; > > + resets = <&ccu RST_BUS_OHCI1>, > > + <&ccu RST_BUS_EHCI1>; > > + phys = <&usbphy 1>; > > + phy-names = "usb"; > > + status = "disabled"; > > + }; > > + > > + ohci1: usb@4200400 { > > + compatible = "allwinner,sun20i-d1-ohci", > > + "generic-ohci"; > > + reg = <0x4200400 0x100>; > > + interrupts = <SOC_PERIPHERAL_IRQ(34) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_OHCI1>, > > + <&ccu CLK_USB_OHCI1>; > > + resets = <&ccu RST_BUS_OHCI1>; > > + phys = <&usbphy 1>; > > + phy-names = "usb"; > > + status = "disabled"; > > + }; > > + > > + emac: ethernet@4500000 { > > + compatible = "allwinner,sun20i-d1-emac", > > + "allwinner,sun50i-a64-emac"; > > + reg = <0x4500000 0x10000>; > > + interrupts = <SOC_PERIPHERAL_IRQ(46) > > IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-names = "macirq"; > > + clocks = <&ccu CLK_BUS_EMAC>; > > + clock-names = "stmmaceth"; > > + resets = <&ccu RST_BUS_EMAC>; > > + reset-names = "stmmaceth"; > > + syscon = <&syscon>; > > + status = "disabled"; > > + > > + mdio: mdio { > > + compatible = "snps,dwmac-mdio"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + }; > > + > > + display_clocks: clock-controller@5000000 { > > The clocks and the two mixers are not children of a bus node anymore, > IIUC correctly this was to manage the SRAM control. Is that now > handled > differently, or does the D1 generation not require this anymore? I think D1 does not require SRAM control at all, only a few SoCs really need the SRAM control to be active for DE to work. > > > + compatible = "allwinner,sun20i-d1-de2-clk", > > + "allwinner,sun50i-h5-de2-clk"; > > + reg = <0x5000000 0x10000>; > > + clocks = <&ccu CLK_BUS_DE>, <&ccu CLK_DE>; > > + clock-names = "bus", "mod"; > > + resets = <&ccu RST_BUS_DE>; > > + #clock-cells = <1>; > > + #reset-cells = <1>; > > + }; > > + > > + mixer0: mixer@5100000 { > > + compatible = "allwinner,sun20i-d1-de2- > > mixer-0"; > > + reg = <0x5100000 0x100000>; > > + clocks = <&display_clocks CLK_BUS_MIXER0>, > > + <&display_clocks CLK_MIXER0>; > > + clock-names = "bus", "mod"; > > + resets = <&display_clocks RST_MIXER0>; > > + > > + ports { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + mixer0_out: port@1 { > > + reg = <1>; > > + > > + mixer0_out_tcon_top_mixer0: > > endpoint { > > + remote-endpoint = > > <&tcon_top_mixer0_in_mixer0>; > > + }; > > + }; > > + }; > > + }; > > + > > + mixer1: mixer@5200000 { > > + compatible = "allwinner,sun20i-d1-de2- > > mixer-1"; > > + reg = <0x5200000 0x100000>; > > + clocks = <&display_clocks CLK_BUS_MIXER1>, > > + <&display_clocks CLK_MIXER1>; > > + clock-names = "bus", "mod"; > > + resets = <&display_clocks RST_MIXER1>; > > + > > + ports { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + mixer1_out: port@1 { > > + reg = <1>; > > + > > + mixer1_out_tcon_top_mixer1: > > endpoint { > > + remote-endpoint = > > <&tcon_top_mixer1_in_mixer1>; > > + }; > > + }; > > + }; > > + }; > > + > > + dsi: dsi@5450000 { > > + compatible = "allwinner,sun20i-d1-mipi- > > dsi", > > + "allwinner,sun50i-a100-mipi- > > dsi"; > > + reg = <0x5450000 0x1000>; > > + interrupts = <SOC_PERIPHERAL_IRQ(92) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_MIPI_DSI>, > > + <&tcon_top CLK_TCON_TOP_DSI>; > > + clock-names = "bus", "mod"; > > + resets = <&ccu RST_BUS_MIPI_DSI>; > > + phys = <&dphy>; > > + phy-names = "dphy"; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + port { > > + dsi_in_tcon_lcd0: endpoint { > > + remote-endpoint = > > <&tcon_lcd0_out_dsi>; > > + }; > > + }; > > + }; > > + > > + dphy: phy@5451000 { > > + compatible = "allwinner,sun20i-d1-mipi- > > dphy", > > + "allwinner,sun50i-a100-mipi- > > dphy"; > > + reg = <0x5451000 0x1000>; > > + interrupts = <SOC_PERIPHERAL_IRQ(92) > > IRQ_TYPE_LEVEL_HIGH>; > > This is the same interrupt number as for the DSI controller above. Is > that correct, and can the drivers handle that? I think this should be correct, and only one driver acquires IRQ now. > > Cheers, > Andre > > > > + clocks = <&ccu CLK_BUS_MIPI_DSI>, > > + <&ccu CLK_MIPI_DSI>; > > + clock-names = "bus", "mod"; > > + resets = <&ccu RST_BUS_MIPI_DSI>; > > + #phy-cells = <0>; > > + }; > > + > > + tcon_top: tcon-top@5460000 { > > + compatible = "allwinner,sun20i-d1-tcon- > > top"; > > + reg = <0x5460000 0x1000>; > > + clocks = <&ccu CLK_BUS_DPSS_TOP>, > > + <&ccu CLK_TCON_TV>, > > + <&ccu CLK_TVE>, > > + <&ccu CLK_TCON_LCD0>; > > + clock-names = "bus", "tcon-tv0", "tve0", > > "dsi"; > > + clock-output-names = "tcon-top-tv0", "tcon- > > top-dsi"; > > + resets = <&ccu RST_BUS_DPSS_TOP>; > > + #clock-cells = <1>; > > + > > + ports { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + tcon_top_mixer0_in: port@0 { > > + reg = <0>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + tcon_top_mixer0_in_mixer0: > > endpoint@0 { > > + reg = <0>; > > + remote-endpoint = > > <&mixer0_out_tcon_top_mixer0>; > > + }; > > + }; > > + > > + tcon_top_mixer0_out: port@1 { > > + reg = <1>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + tcon_top_mixer0_out_tcon_lc > > d0: endpoint@0 { > > + reg = <0>; > > + remote-endpoint = > > <&tcon_lcd0_in_tcon_top_mixer0>; > > + }; > > + > > + tcon_top_mixer0_out_tcon_tv > > 0: endpoint@2 { > > + reg = <2>; > > + remote-endpoint = > > <&tcon_tv0_in_tcon_top_mixer0>; > > + }; > > + }; > > + > > + tcon_top_mixer1_in: port@2 { > > + reg = <2>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + tcon_top_mixer1_in_mixer1: > > endpoint@1 { > > + reg = <1>; > > + remote-endpoint = > > <&mixer1_out_tcon_top_mixer1>; > > + }; > > + }; > > + > > + tcon_top_mixer1_out: port@3 { > > + reg = <3>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + tcon_top_mixer1_out_tcon_lc > > d0: endpoint@0 { > > + reg = <0>; > > + remote-endpoint = > > <&tcon_lcd0_in_tcon_top_mixer1>; > > + }; > > + > > + tcon_top_mixer1_out_tcon_tv > > 0: endpoint@2 { > > + reg = <2>; > > + remote-endpoint = > > <&tcon_tv0_in_tcon_top_mixer1>; > > + }; > > + }; > > + > > + tcon_top_hdmi_in: port@4 { > > + reg = <4>; > > + > > + tcon_top_hdmi_in_tcon_tv0: > > endpoint { > > + remote-endpoint = > > <&tcon_tv0_out_tcon_top_hdmi>; > > + }; > > + }; > > + > > + tcon_top_hdmi_out: port@5 { > > + reg = <5>; > > + }; > > + }; > > + }; > > + > > + tcon_lcd0: lcd-controller@5461000 { > > + compatible = "allwinner,sun20i-d1-tcon- > > lcd"; > > + reg = <0x5461000 0x1000>; > > + interrupts = <SOC_PERIPHERAL_IRQ(90) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_TCON_LCD0>, > > + <&ccu CLK_TCON_LCD0>; > > + clock-names = "ahb", "tcon-ch0"; > > + clock-output-names = "tcon-pixel-clock"; > > + resets = <&ccu RST_BUS_TCON_LCD0>, > > + <&ccu RST_BUS_LVDS0>; > > + reset-names = "lcd", "lvds"; > > + #clock-cells = <0>; > > + > > + ports { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + tcon_lcd0_in: port@0 { > > + reg = <0>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + tcon_lcd0_in_tcon_top_mixer > > 0: endpoint@0 { > > + reg = <0>; > > + remote-endpoint = > > <&tcon_top_mixer0_out_tcon_lcd0>; > > + }; > > + > > + tcon_lcd0_in_tcon_top_mixer > > 1: endpoint@1 { > > + reg = <1>; > > + remote-endpoint = > > <&tcon_top_mixer1_out_tcon_lcd0>; > > + }; > > + }; > > + > > + tcon_lcd0_out: port@1 { > > + reg = <1>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + tcon_lcd0_out_dsi: > > endpoint@1 { > > + reg = <1>; > > + remote-endpoint = > > <&dsi_in_tcon_lcd0>; > > + }; > > + }; > > + }; > > + }; > > + > > + tcon_tv0: lcd-controller@5470000 { > > + compatible = "allwinner,sun20i-d1-tcon-tv"; > > + reg = <0x5470000 0x1000>; > > + interrupts = <SOC_PERIPHERAL_IRQ(91) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_TCON_TV>, > > + <&tcon_top CLK_TCON_TOP_TV0>; > > + clock-names = "ahb", "tcon-ch1"; > > + resets = <&ccu RST_BUS_TCON_TV>; > > + reset-names = "lcd"; > > + > > + ports { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + tcon_tv0_in: port@0 { > > + reg = <0>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + tcon_tv0_in_tcon_top_mixer0 > > : endpoint@0 { > > + reg = <0>; > > + remote-endpoint = > > <&tcon_top_mixer0_out_tcon_tv0>; > > + }; > > + > > + tcon_tv0_in_tcon_top_mixer1 > > : endpoint@1 { > > + reg = <1>; > > + remote-endpoint = > > <&tcon_top_mixer1_out_tcon_tv0>; > > + }; > > + }; > > + > > + tcon_tv0_out: port@1 { > > + reg = <1>; > > + > > + tcon_tv0_out_tcon_top_hdmi: > > endpoint { > > + remote-endpoint = > > <&tcon_top_hdmi_in_tcon_tv0>; > > + }; > > + }; > > + }; > > + }; > > + > > + r_ccu: clock-controller@7010000 { > > + compatible = "allwinner,sun20i-d1-r-ccu"; > > + reg = <0x7010000 0x400>; > > + clocks = <&dcxo>, > > + <&rtc CLK_OSC32K>, > > + <&rtc CLK_IOSC>, > > + <&ccu CLK_PLL_PERIPH0_DIV3>; > > + clock-names = "hosc", "losc", "iosc", "pll- > > periph"; > > + #clock-cells = <1>; > > + #reset-cells = <1>; > > + }; > > + > > + rtc: rtc@7090000 { > > + compatible = "allwinner,sun20i-d1-rtc", > > + "allwinner,sun50i-r329-rtc"; > > + reg = <0x7090000 0x400>; > > + interrupts = <SOC_PERIPHERAL_IRQ(144) > > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&r_ccu CLK_BUS_R_RTC>, > > + <&dcxo>, > > + <&r_ccu CLK_R_AHB>; > > + clock-names = "bus", "hosc", "ahb"; > > + #clock-cells = <1>; > > + }; > > + }; > > +}; > >
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi b/arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi new file mode 100644 index 000000000000..97e7cbb32597 --- /dev/null +++ b/arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi @@ -0,0 +1,66 @@ +// SPDX-License-Identifier: (GPL-2.0+ or MIT) +// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org> + +#include "sun20i-d1s.dtsi" +#include "sunxi-d1-t113.dtsi" + +/ { + soc { + lradc: keys@2009800 { + compatible = "allwinner,sun20i-d1-lradc", + "allwinner,sun50i-r329-lradc"; + reg = <0x2009800 0x400>; + interrupts = <SOC_PERIPHERAL_IRQ(61) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_LRADC>; + resets = <&ccu RST_BUS_LRADC>; + status = "disabled"; + }; + + i2s0: i2s@2032000 { + compatible = "allwinner,sun20i-d1-i2s", + "allwinner,sun50i-r329-i2s"; + reg = <0x2032000 0x1000>; + interrupts = <SOC_PERIPHERAL_IRQ(26) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2S0>, + <&ccu CLK_I2S0>; + clock-names = "apb", "mod"; + resets = <&ccu RST_BUS_I2S0>; + dmas = <&dma 3>, <&dma 3>; + dma-names = "rx", "tx"; + status = "disabled"; + #sound-dai-cells = <0>; + }; + }; +}; + +&pio { + /omit-if-no-ref/ + dmic_pb11_d0_pin: dmic-pb11-d0-pin { + pins = "PB11"; + function = "dmic"; + }; + + /omit-if-no-ref/ + dmic_pe17_clk_pin: dmic-pe17-clk-pin { + pins = "PE17"; + function = "dmic"; + }; + + /omit-if-no-ref/ + i2c0_pb10_pins: i2c0-pb10-pins { + pins = "PB10", "PB11"; + function = "i2c0"; + }; + + /omit-if-no-ref/ + i2c2_pb0_pins: i2c2-pb0-pins { + pins = "PB0", "PB1"; + function = "i2c2"; + }; + + /omit-if-no-ref/ + uart0_pb8_pins: uart0-pb8-pins { + pins = "PB8", "PB9"; + function = "uart0"; + }; +}; diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi b/arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi new file mode 100644 index 000000000000..859509832d58 --- /dev/null +++ b/arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi @@ -0,0 +1,76 @@ +// SPDX-License-Identifier: (GPL-2.0+ or MIT) +// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org> + +#define SOC_PERIPHERAL_IRQ(nr) (nr + 16) + +#include "sunxi-d1s-t113.dtsi" + +/ { + cpus { + timebase-frequency = <24000000>; + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + compatible = "thead,c906", "riscv"; + device_type = "cpu"; + reg = <0>; + clocks = <&ccu CLK_RISCV>; + d-cache-block-size = <64>; + d-cache-sets = <256>; + d-cache-size = <32768>; + i-cache-block-size = <64>; + i-cache-sets = <128>; + i-cache-size = <32768>; + mmu-type = "riscv,sv39"; + operating-points-v2 = <&opp_table_cpu>; + riscv,isa = "rv64imafdc"; + #cooling-cells = <2>; + + cpu0_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + }; + }; + + opp_table_cpu: opp-table-cpu { + compatible = "operating-points-v2"; + + opp-408000000 { + opp-hz = /bits/ 64 <408000000>; + opp-microvolt = <900000 900000 1100000>; + }; + + opp-1080000000 { + opp-hz = /bits/ 64 <1008000000>; + opp-microvolt = <900000 900000 1100000>; + }; + }; + + soc { + interrupt-parent = <&plic>; + + riscv_wdt: watchdog@6011000 { + compatible = "allwinner,sun20i-d1-wdt"; + reg = <0x6011000 0x20>; + interrupts = <SOC_PERIPHERAL_IRQ(131) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&dcxo>, <&rtc CLK_OSC32K>; + clock-names = "hosc", "losc"; + }; + + plic: interrupt-controller@10000000 { + compatible = "allwinner,sun20i-d1-plic", + "thead,c900-plic"; + reg = <0x10000000 0x4000000>; + interrupts-extended = <&cpu0_intc 11>, + <&cpu0_intc 9>; + interrupt-controller; + riscv,ndev = <176>; + #address-cells = <0>; + #interrupt-cells = <2>; + }; + }; +}; diff --git a/arch/riscv/boot/dts/allwinner/sunxi-d1-t113.dtsi b/arch/riscv/boot/dts/allwinner/sunxi-d1-t113.dtsi new file mode 100644 index 000000000000..b7156123df54 --- /dev/null +++ b/arch/riscv/boot/dts/allwinner/sunxi-d1-t113.dtsi @@ -0,0 +1,15 @@ +// SPDX-License-Identifier: (GPL-2.0+ or MIT) +// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org> + +/ { + soc { + dsp_wdt: watchdog@1700400 { + compatible = "allwinner,sun20i-d1-wdt"; + reg = <0x1700400 0x20>; + interrupts = <SOC_PERIPHERAL_IRQ(122) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&dcxo>, <&rtc CLK_OSC32K>; + clock-names = "hosc", "losc"; + status = "reserved"; + }; + }; +}; diff --git a/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi b/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi new file mode 100644 index 000000000000..c8815cbf0b46 --- /dev/null +++ b/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi @@ -0,0 +1,844 @@ +// SPDX-License-Identifier: (GPL-2.0+ or MIT) +// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org> + +#include <dt-bindings/clock/sun6i-rtc.h> +#include <dt-bindings/clock/sun8i-de2.h> +#include <dt-bindings/clock/sun8i-tcon-top.h> +#include <dt-bindings/clock/sun20i-d1-ccu.h> +#include <dt-bindings/clock/sun20i-d1-r-ccu.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/reset/sun8i-de2.h> +#include <dt-bindings/reset/sun20i-d1-ccu.h> +#include <dt-bindings/reset/sun20i-d1-r-ccu.h> + +/ { + #address-cells = <1>; + #size-cells = <1>; + + dcxo: dcxo-clk { + compatible = "fixed-clock"; + /* This value must be overridden by the board */ + clock-frequency = <0>; + clock-output-names = "dcxo"; + #clock-cells = <0>; + }; + + de: display-engine { + compatible = "allwinner,sun20i-d1-display-engine"; + allwinner,pipelines = <&mixer0>, <&mixer1>; + status = "disabled"; + }; + + soc { + compatible = "simple-bus"; + ranges; + dma-noncoherent; + #address-cells = <1>; + #size-cells = <1>; + + pio: pinctrl@2000000 { + compatible = "allwinner,sun20i-d1-pinctrl"; + reg = <0x2000000 0x800>; + interrupts = <SOC_PERIPHERAL_IRQ(69) IRQ_TYPE_LEVEL_HIGH>, + <SOC_PERIPHERAL_IRQ(71) IRQ_TYPE_LEVEL_HIGH>, + <SOC_PERIPHERAL_IRQ(73) IRQ_TYPE_LEVEL_HIGH>, + <SOC_PERIPHERAL_IRQ(75) IRQ_TYPE_LEVEL_HIGH>, + <SOC_PERIPHERAL_IRQ(77) IRQ_TYPE_LEVEL_HIGH>, + <SOC_PERIPHERAL_IRQ(79) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_APB0>, + <&dcxo>, + <&rtc CLK_OSC32K>; + clock-names = "apb", "hosc", "losc"; + gpio-controller; + interrupt-controller; + #gpio-cells = <3>; + #interrupt-cells = <3>; + + /omit-if-no-ref/ + clk_pg11_pin: clk-pg11-pin { + pins = "PG11"; + function = "clk"; + }; + + /omit-if-no-ref/ + dsi_4lane_pins: dsi-4lane-pins { + pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5", + "PD6", "PD7", "PD8", "PD9"; + drive-strength = <30>; + function = "dsi"; + }; + + /omit-if-no-ref/ + lcd_rgb666_pins: lcd-rgb666-pins { + pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5", + "PD6", "PD7", "PD8", "PD9", "PD10", "PD11", + "PD12", "PD13", "PD14", "PD15", "PD16", "PD17", + "PD18", "PD19", "PD20", "PD21"; + function = "lcd0"; + }; + + /omit-if-no-ref/ + mmc0_pins: mmc0-pins { + pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5"; + function = "mmc0"; + }; + + /omit-if-no-ref/ + mmc1_pins: mmc1-pins { + pins = "PG0", "PG1", "PG2", "PG3", "PG4", "PG5"; + function = "mmc1"; + }; + + /omit-if-no-ref/ + mmc2_pins: mmc2-pins { + pins = "PC2", "PC3", "PC4", "PC5", "PC6", "PC7"; + function = "mmc2"; + }; + + /omit-if-no-ref/ + rgmii_pe_pins: rgmii-pe-pins { + pins = "PE0", "PE1", "PE2", "PE3", "PE4", + "PE5", "PE6", "PE7", "PE8", "PE9", + "PE11", "PE12", "PE13", "PE14", "PE15"; + function = "emac"; + }; + + /omit-if-no-ref/ + rmii_pe_pins: rmii-pe-pins { + pins = "PE0", "PE1", "PE2", "PE3", "PE4", + "PE5", "PE6", "PE7", "PE8", "PE9"; + function = "emac"; + }; + + /omit-if-no-ref/ + uart1_pg6_pins: uart1-pg6-pins { + pins = "PG6", "PG7"; + function = "uart1"; + }; + + /omit-if-no-ref/ + uart1_pg8_rts_cts_pins: uart1-pg8-rts-cts-pins { + pins = "PG8", "PG9"; + function = "uart1"; + }; + + /omit-if-no-ref/ + uart3_pb_pins: uart3-pb-pins { + pins = "PB6", "PB7"; + function = "uart3"; + }; + }; + + ccu: clock-controller@2001000 { + compatible = "allwinner,sun20i-d1-ccu"; + reg = <0x2001000 0x1000>; + clocks = <&dcxo>, + <&rtc CLK_OSC32K>, + <&rtc CLK_IOSC>; + clock-names = "hosc", "losc", "iosc"; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + dmic: dmic@2031000 { + compatible = "allwinner,sun20i-d1-dmic", + "allwinner,sun50i-h6-dmic"; + reg = <0x2031000 0x400>; + interrupts = <SOC_PERIPHERAL_IRQ(24) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_DMIC>, + <&ccu CLK_DMIC>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_DMIC>; + dmas = <&dma 8>; + dma-names = "rx"; + status = "disabled"; + #sound-dai-cells = <0>; + }; + + i2s1: i2s@2033000 { + compatible = "allwinner,sun20i-d1-i2s", + "allwinner,sun50i-r329-i2s"; + reg = <0x2033000 0x1000>; + interrupts = <SOC_PERIPHERAL_IRQ(27) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2S1>, + <&ccu CLK_I2S1>; + clock-names = "apb", "mod"; + resets = <&ccu RST_BUS_I2S1>; + dmas = <&dma 4>, <&dma 4>; + dma-names = "rx", "tx"; + status = "disabled"; + #sound-dai-cells = <0>; + }; + + i2s2: i2s@2034000 { + compatible = "allwinner,sun20i-d1-i2s", + "allwinner,sun50i-r329-i2s"; + reg = <0x2034000 0x1000>; + interrupts = <SOC_PERIPHERAL_IRQ(28) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2S2>, + <&ccu CLK_I2S2>; + clock-names = "apb", "mod"; + resets = <&ccu RST_BUS_I2S2>; + dmas = <&dma 5>, <&dma 5>; + dma-names = "rx", "tx"; + status = "disabled"; + #sound-dai-cells = <0>; + }; + + timer: timer@2050000 { + compatible = "allwinner,sun20i-d1-timer", + "allwinner,sun8i-a23-timer"; + reg = <0x2050000 0xa0>; + interrupts = <SOC_PERIPHERAL_IRQ(59) IRQ_TYPE_LEVEL_HIGH>, + <SOC_PERIPHERAL_IRQ(60) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&dcxo>; + }; + + wdt: watchdog@20500a0 { + compatible = "allwinner,sun20i-d1-wdt-reset", + "allwinner,sun20i-d1-wdt"; + reg = <0x20500a0 0x20>; + interrupts = <SOC_PERIPHERAL_IRQ(63) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&dcxo>, <&rtc CLK_OSC32K>; + clock-names = "hosc", "losc"; + status = "reserved"; + }; + + uart0: serial@2500000 { + compatible = "snps,dw-apb-uart"; + reg = <0x2500000 0x400>; + reg-io-width = <4>; + reg-shift = <2>; + interrupts = <SOC_PERIPHERAL_IRQ(2) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_UART0>; + resets = <&ccu RST_BUS_UART0>; + dmas = <&dma 14>, <&dma 14>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + uart1: serial@2500400 { + compatible = "snps,dw-apb-uart"; + reg = <0x2500400 0x400>; + reg-io-width = <4>; + reg-shift = <2>; + interrupts = <SOC_PERIPHERAL_IRQ(3) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_UART1>; + resets = <&ccu RST_BUS_UART1>; + dmas = <&dma 15>, <&dma 15>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + uart2: serial@2500800 { + compatible = "snps,dw-apb-uart"; + reg = <0x2500800 0x400>; + reg-io-width = <4>; + reg-shift = <2>; + interrupts = <SOC_PERIPHERAL_IRQ(4) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_UART2>; + resets = <&ccu RST_BUS_UART2>; + dmas = <&dma 16>, <&dma 16>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + uart3: serial@2500c00 { + compatible = "snps,dw-apb-uart"; + reg = <0x2500c00 0x400>; + reg-io-width = <4>; + reg-shift = <2>; + interrupts = <SOC_PERIPHERAL_IRQ(5) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_UART3>; + resets = <&ccu RST_BUS_UART3>; + dmas = <&dma 17>, <&dma 17>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + uart4: serial@2501000 { + compatible = "snps,dw-apb-uart"; + reg = <0x2501000 0x400>; + reg-io-width = <4>; + reg-shift = <2>; + interrupts = <SOC_PERIPHERAL_IRQ(6) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_UART4>; + resets = <&ccu RST_BUS_UART4>; + dmas = <&dma 18>, <&dma 18>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + uart5: serial@2501400 { + compatible = "snps,dw-apb-uart"; + reg = <0x2501400 0x400>; + reg-io-width = <4>; + reg-shift = <2>; + interrupts = <SOC_PERIPHERAL_IRQ(7) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_UART5>; + resets = <&ccu RST_BUS_UART5>; + dmas = <&dma 19>, <&dma 19>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + i2c0: i2c@2502000 { + compatible = "allwinner,sun20i-d1-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x2502000 0x400>; + interrupts = <SOC_PERIPHERAL_IRQ(9) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C0>; + resets = <&ccu RST_BUS_I2C0>; + dmas = <&dma 43>, <&dma 43>; + dma-names = "rx", "tx"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c1: i2c@2502400 { + compatible = "allwinner,sun20i-d1-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x2502400 0x400>; + interrupts = <SOC_PERIPHERAL_IRQ(10) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C1>; + resets = <&ccu RST_BUS_I2C1>; + dmas = <&dma 44>, <&dma 44>; + dma-names = "rx", "tx"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c2: i2c@2502800 { + compatible = "allwinner,sun20i-d1-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x2502800 0x400>; + interrupts = <SOC_PERIPHERAL_IRQ(11) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C2>; + resets = <&ccu RST_BUS_I2C2>; + dmas = <&dma 45>, <&dma 45>; + dma-names = "rx", "tx"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c3: i2c@2502c00 { + compatible = "allwinner,sun20i-d1-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x2502c00 0x400>; + interrupts = <SOC_PERIPHERAL_IRQ(12) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C3>; + resets = <&ccu RST_BUS_I2C3>; + dmas = <&dma 46>, <&dma 46>; + dma-names = "rx", "tx"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + syscon: syscon@3000000 { + compatible = "allwinner,sun20i-d1-system-control"; + reg = <0x3000000 0x1000>; + ranges; + #address-cells = <1>; + #size-cells = <1>; + + regulators@3000150 { + compatible = "allwinner,sun20i-d1-system-ldos"; + reg = <0x3000150 0x4>; + + reg_ldoa: ldoa { + }; + + reg_ldob: ldob { + }; + }; + }; + + dma: dma-controller@3002000 { + compatible = "allwinner,sun20i-d1-dma"; + reg = <0x3002000 0x1000>; + interrupts = <SOC_PERIPHERAL_IRQ(50) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_DMA>, <&ccu CLK_MBUS_DMA>; + clock-names = "bus", "mbus"; + resets = <&ccu RST_BUS_DMA>; + dma-channels = <16>; + dma-requests = <48>; + #dma-cells = <1>; + }; + + sid: efuse@3006000 { + compatible = "allwinner,sun20i-d1-sid"; + reg = <0x3006000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + }; + + mbus: dram-controller@3102000 { + compatible = "allwinner,sun20i-d1-mbus"; + reg = <0x3102000 0x1000>, + <0x3103000 0x1000>; + reg-names = "mbus", "dram"; + interrupts = <SOC_PERIPHERAL_IRQ(43) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_MBUS>, + <&ccu CLK_DRAM>, + <&ccu CLK_BUS_DRAM>; + clock-names = "mbus", "dram", "bus"; + dma-ranges = <0 0x40000000 0x80000000>; + #address-cells = <1>; + #size-cells = <1>; + #interconnect-cells = <1>; + }; + + mmc0: mmc@4020000 { + compatible = "allwinner,sun20i-d1-mmc"; + reg = <0x4020000 0x1000>; + interrupts = <SOC_PERIPHERAL_IRQ(40) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC0>; + reset-names = "ahb"; + cap-sd-highspeed; + max-frequency = <150000000>; + no-mmc; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + mmc1: mmc@4021000 { + compatible = "allwinner,sun20i-d1-mmc"; + reg = <0x4021000 0x1000>; + interrupts = <SOC_PERIPHERAL_IRQ(41) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC1>; + reset-names = "ahb"; + cap-sd-highspeed; + max-frequency = <150000000>; + no-mmc; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + mmc2: mmc@4022000 { + compatible = "allwinner,sun20i-d1-emmc", + "allwinner,sun50i-a100-emmc"; + reg = <0x4022000 0x1000>; + interrupts = <SOC_PERIPHERAL_IRQ(42) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC2>; + reset-names = "ahb"; + cap-mmc-highspeed; + max-frequency = <150000000>; + mmc-ddr-1_8v; + mmc-ddr-3_3v; + no-sd; + no-sdio; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + usb_otg: usb@4100000 { + compatible = "allwinner,sun20i-d1-musb", + "allwinner,sun8i-a33-musb"; + reg = <0x4100000 0x400>; + interrupts = <SOC_PERIPHERAL_IRQ(29) IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "mc"; + clocks = <&ccu CLK_BUS_OTG>; + resets = <&ccu RST_BUS_OTG>; + extcon = <&usbphy 0>; + phys = <&usbphy 0>; + phy-names = "usb"; + status = "disabled"; + }; + + usbphy: phy@4100400 { + compatible = "allwinner,sun20i-d1-usb-phy"; + reg = <0x4100400 0x100>, + <0x4101800 0x100>, + <0x4200800 0x100>; + reg-names = "phy_ctrl", + "pmu0", + "pmu1"; + clocks = <&dcxo>, + <&dcxo>; + clock-names = "usb0_phy", + "usb1_phy"; + resets = <&ccu RST_USB_PHY0>, + <&ccu RST_USB_PHY1>; + reset-names = "usb0_reset", + "usb1_reset"; + status = "disabled"; + #phy-cells = <1>; + }; + + ehci0: usb@4101000 { + compatible = "allwinner,sun20i-d1-ehci", + "generic-ehci"; + reg = <0x4101000 0x100>; + interrupts = <SOC_PERIPHERAL_IRQ(30) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_OHCI0>, + <&ccu CLK_BUS_EHCI0>, + <&ccu CLK_USB_OHCI0>; + resets = <&ccu RST_BUS_OHCI0>, + <&ccu RST_BUS_EHCI0>; + phys = <&usbphy 0>; + phy-names = "usb"; + status = "disabled"; + }; + + ohci0: usb@4101400 { + compatible = "allwinner,sun20i-d1-ohci", + "generic-ohci"; + reg = <0x4101400 0x100>; + interrupts = <SOC_PERIPHERAL_IRQ(31) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_OHCI0>, + <&ccu CLK_USB_OHCI0>; + resets = <&ccu RST_BUS_OHCI0>; + phys = <&usbphy 0>; + phy-names = "usb"; + status = "disabled"; + }; + + ehci1: usb@4200000 { + compatible = "allwinner,sun20i-d1-ehci", + "generic-ehci"; + reg = <0x4200000 0x100>; + interrupts = <SOC_PERIPHERAL_IRQ(33) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_OHCI1>, + <&ccu CLK_BUS_EHCI1>, + <&ccu CLK_USB_OHCI1>; + resets = <&ccu RST_BUS_OHCI1>, + <&ccu RST_BUS_EHCI1>; + phys = <&usbphy 1>; + phy-names = "usb"; + status = "disabled"; + }; + + ohci1: usb@4200400 { + compatible = "allwinner,sun20i-d1-ohci", + "generic-ohci"; + reg = <0x4200400 0x100>; + interrupts = <SOC_PERIPHERAL_IRQ(34) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_OHCI1>, + <&ccu CLK_USB_OHCI1>; + resets = <&ccu RST_BUS_OHCI1>; + phys = <&usbphy 1>; + phy-names = "usb"; + status = "disabled"; + }; + + emac: ethernet@4500000 { + compatible = "allwinner,sun20i-d1-emac", + "allwinner,sun50i-a64-emac"; + reg = <0x4500000 0x10000>; + interrupts = <SOC_PERIPHERAL_IRQ(46) IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + clocks = <&ccu CLK_BUS_EMAC>; + clock-names = "stmmaceth"; + resets = <&ccu RST_BUS_EMAC>; + reset-names = "stmmaceth"; + syscon = <&syscon>; + status = "disabled"; + + mdio: mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + display_clocks: clock-controller@5000000 { + compatible = "allwinner,sun20i-d1-de2-clk", + "allwinner,sun50i-h5-de2-clk"; + reg = <0x5000000 0x10000>; + clocks = <&ccu CLK_BUS_DE>, <&ccu CLK_DE>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_DE>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + mixer0: mixer@5100000 { + compatible = "allwinner,sun20i-d1-de2-mixer-0"; + reg = <0x5100000 0x100000>; + clocks = <&display_clocks CLK_BUS_MIXER0>, + <&display_clocks CLK_MIXER0>; + clock-names = "bus", "mod"; + resets = <&display_clocks RST_MIXER0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + mixer0_out: port@1 { + reg = <1>; + + mixer0_out_tcon_top_mixer0: endpoint { + remote-endpoint = <&tcon_top_mixer0_in_mixer0>; + }; + }; + }; + }; + + mixer1: mixer@5200000 { + compatible = "allwinner,sun20i-d1-de2-mixer-1"; + reg = <0x5200000 0x100000>; + clocks = <&display_clocks CLK_BUS_MIXER1>, + <&display_clocks CLK_MIXER1>; + clock-names = "bus", "mod"; + resets = <&display_clocks RST_MIXER1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + mixer1_out: port@1 { + reg = <1>; + + mixer1_out_tcon_top_mixer1: endpoint { + remote-endpoint = <&tcon_top_mixer1_in_mixer1>; + }; + }; + }; + }; + + dsi: dsi@5450000 { + compatible = "allwinner,sun20i-d1-mipi-dsi", + "allwinner,sun50i-a100-mipi-dsi"; + reg = <0x5450000 0x1000>; + interrupts = <SOC_PERIPHERAL_IRQ(92) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_MIPI_DSI>, + <&tcon_top CLK_TCON_TOP_DSI>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_MIPI_DSI>; + phys = <&dphy>; + phy-names = "dphy"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + + port { + dsi_in_tcon_lcd0: endpoint { + remote-endpoint = <&tcon_lcd0_out_dsi>; + }; + }; + }; + + dphy: phy@5451000 { + compatible = "allwinner,sun20i-d1-mipi-dphy", + "allwinner,sun50i-a100-mipi-dphy"; + reg = <0x5451000 0x1000>; + interrupts = <SOC_PERIPHERAL_IRQ(92) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_MIPI_DSI>, + <&ccu CLK_MIPI_DSI>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_MIPI_DSI>; + #phy-cells = <0>; + }; + + tcon_top: tcon-top@5460000 { + compatible = "allwinner,sun20i-d1-tcon-top"; + reg = <0x5460000 0x1000>; + clocks = <&ccu CLK_BUS_DPSS_TOP>, + <&ccu CLK_TCON_TV>, + <&ccu CLK_TVE>, + <&ccu CLK_TCON_LCD0>; + clock-names = "bus", "tcon-tv0", "tve0", "dsi"; + clock-output-names = "tcon-top-tv0", "tcon-top-dsi"; + resets = <&ccu RST_BUS_DPSS_TOP>; + #clock-cells = <1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + tcon_top_mixer0_in: port@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + tcon_top_mixer0_in_mixer0: endpoint@0 { + reg = <0>; + remote-endpoint = <&mixer0_out_tcon_top_mixer0>; + }; + }; + + tcon_top_mixer0_out: port@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + tcon_top_mixer0_out_tcon_lcd0: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon_lcd0_in_tcon_top_mixer0>; + }; + + tcon_top_mixer0_out_tcon_tv0: endpoint@2 { + reg = <2>; + remote-endpoint = <&tcon_tv0_in_tcon_top_mixer0>; + }; + }; + + tcon_top_mixer1_in: port@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + tcon_top_mixer1_in_mixer1: endpoint@1 { + reg = <1>; + remote-endpoint = <&mixer1_out_tcon_top_mixer1>; + }; + }; + + tcon_top_mixer1_out: port@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + tcon_top_mixer1_out_tcon_lcd0: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon_lcd0_in_tcon_top_mixer1>; + }; + + tcon_top_mixer1_out_tcon_tv0: endpoint@2 { + reg = <2>; + remote-endpoint = <&tcon_tv0_in_tcon_top_mixer1>; + }; + }; + + tcon_top_hdmi_in: port@4 { + reg = <4>; + + tcon_top_hdmi_in_tcon_tv0: endpoint { + remote-endpoint = <&tcon_tv0_out_tcon_top_hdmi>; + }; + }; + + tcon_top_hdmi_out: port@5 { + reg = <5>; + }; + }; + }; + + tcon_lcd0: lcd-controller@5461000 { + compatible = "allwinner,sun20i-d1-tcon-lcd"; + reg = <0x5461000 0x1000>; + interrupts = <SOC_PERIPHERAL_IRQ(90) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_TCON_LCD0>, + <&ccu CLK_TCON_LCD0>; + clock-names = "ahb", "tcon-ch0"; + clock-output-names = "tcon-pixel-clock"; + resets = <&ccu RST_BUS_TCON_LCD0>, + <&ccu RST_BUS_LVDS0>; + reset-names = "lcd", "lvds"; + #clock-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + tcon_lcd0_in: port@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + tcon_lcd0_in_tcon_top_mixer0: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon_top_mixer0_out_tcon_lcd0>; + }; + + tcon_lcd0_in_tcon_top_mixer1: endpoint@1 { + reg = <1>; + remote-endpoint = <&tcon_top_mixer1_out_tcon_lcd0>; + }; + }; + + tcon_lcd0_out: port@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + tcon_lcd0_out_dsi: endpoint@1 { + reg = <1>; + remote-endpoint = <&dsi_in_tcon_lcd0>; + }; + }; + }; + }; + + tcon_tv0: lcd-controller@5470000 { + compatible = "allwinner,sun20i-d1-tcon-tv"; + reg = <0x5470000 0x1000>; + interrupts = <SOC_PERIPHERAL_IRQ(91) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_TCON_TV>, + <&tcon_top CLK_TCON_TOP_TV0>; + clock-names = "ahb", "tcon-ch1"; + resets = <&ccu RST_BUS_TCON_TV>; + reset-names = "lcd"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + tcon_tv0_in: port@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + tcon_tv0_in_tcon_top_mixer0: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon_top_mixer0_out_tcon_tv0>; + }; + + tcon_tv0_in_tcon_top_mixer1: endpoint@1 { + reg = <1>; + remote-endpoint = <&tcon_top_mixer1_out_tcon_tv0>; + }; + }; + + tcon_tv0_out: port@1 { + reg = <1>; + + tcon_tv0_out_tcon_top_hdmi: endpoint { + remote-endpoint = <&tcon_top_hdmi_in_tcon_tv0>; + }; + }; + }; + }; + + r_ccu: clock-controller@7010000 { + compatible = "allwinner,sun20i-d1-r-ccu"; + reg = <0x7010000 0x400>; + clocks = <&dcxo>, + <&rtc CLK_OSC32K>, + <&rtc CLK_IOSC>, + <&ccu CLK_PLL_PERIPH0_DIV3>; + clock-names = "hosc", "losc", "iosc", "pll-periph"; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + rtc: rtc@7090000 { + compatible = "allwinner,sun20i-d1-rtc", + "allwinner,sun50i-r329-rtc"; + reg = <0x7090000 0x400>; + interrupts = <SOC_PERIPHERAL_IRQ(144) IRQ_TYPE_LEVEL_HIGH>; + clocks = <&r_ccu CLK_BUS_R_RTC>, + <&dcxo>, + <&r_ccu CLK_R_AHB>; + clock-names = "bus", "hosc", "ahb"; + #clock-cells = <1>; + }; + }; +};
D1 (aka D1-H), D1s (aka F133), R528, and T113 are a family of SoCs based on a single die, or at a pair of dies derived from the same design. D1 and D1s contain a single T-HEAD Xuantie C906 CPU, whereas R528 and T113 contain a pair of Cortex-A7's. D1 and R528 are the full version of the chip with a BGA package, whereas D1s and T113 are low-pin-count QFP variants. Because the original design supported both ARM and RISC-V CPUs, some peripherals are duplicated. In addition, all variants except D1s contain a HiFi 4 DSP with its own set of peripherals. The devicetrees are organized to minimize duplication: - Common perhiperals are described in sunxi-d1s-t113.dtsi - DSP-related peripherals are described in sunxi-d1-t113.dtsi - RISC-V specific hardware is described in sun20i-d1s.dtsi - Functionality unique to the D1 variant is described in sun20i-d1.dtsi The SOC_PERIPHERAL_IRQ macro handles the different #interrupt-cells values between the ARM (GIC) and RISC-V (PLIC) versions of the SoC. Signed-off-by: Samuel Holland <samuel@sholland.org> --- Changes in v2: - Split into separate files for sharing with D1s/R528/T113 - Use SOC_PERIPHERAL_IRQ macro for interrupts - Rename osc24M to dcxo and move the frequency to the board DTs - Drop analog LDOs due to the missing binding - Correct tcon_top DSI clock reference - Add DMIC, DSI controller, and DPHY (bindings are in linux-next) - Add CPU OPP table arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi | 66 ++ arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi | 76 ++ .../boot/dts/allwinner/sunxi-d1-t113.dtsi | 15 + .../boot/dts/allwinner/sunxi-d1s-t113.dtsi | 844 ++++++++++++++++++ 4 files changed, 1001 insertions(+) create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi create mode 100644 arch/riscv/boot/dts/allwinner/sunxi-d1-t113.dtsi create mode 100644 arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi