diff mbox series

[07/21] spi: s3c64xx: use bitfield access macros

Message ID 20240123153421.715951-8-tudor.ambarus@linaro.org
State Superseded
Headers show
Series spi: s3c64xx: winter cleanup and gs101 support | expand

Commit Message

Tudor Ambarus Jan. 23, 2024, 3:34 p.m. UTC 
Use the bitfield access macros in order to clean and to make the driver
easier to read.

Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
---
 drivers/spi/spi-s3c64xx.c | 196 +++++++++++++++++++-------------------
 1 file changed, 99 insertions(+), 97 deletions(-)

Comments

Andi Shyti Jan. 25, 2024, 10:50 p.m. UTC | #1 
Hi Tudor,

On Tue, Jan 23, 2024 at 03:34:06PM +0000, Tudor Ambarus wrote:
> Use the bitfield access macros in order to clean and to make the driver
> easier to read.

most of the changes done here are allignment. I would mention it
in the log.

> Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
> ---

...

> -#define S3C64XX_SPI_CLKSEL_SRCMSK	(3<<9)
> -#define S3C64XX_SPI_CLKSEL_SRCSHFT	9
> -#define S3C64XX_SPI_ENCLK_ENABLE	(1<<8)
> -#define S3C64XX_SPI_PSR_MASK		0xff
> -
> -#define S3C64XX_SPI_MODE_CH_TSZ_BYTE		(0<<29)
> -#define S3C64XX_SPI_MODE_CH_TSZ_HALFWORD	(1<<29)
> -#define S3C64XX_SPI_MODE_CH_TSZ_WORD		(2<<29)
> -#define S3C64XX_SPI_MODE_CH_TSZ_MASK		(3<<29)
> -#define S3C64XX_SPI_MODE_BUS_TSZ_BYTE		(0<<17)
> -#define S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD	(1<<17)
> -#define S3C64XX_SPI_MODE_BUS_TSZ_WORD		(2<<17)
> -#define S3C64XX_SPI_MODE_BUS_TSZ_MASK		(3<<17)
> +#define S3C64XX_SPI_CH_CFG			0x00
> +#define S3C64XX_SPI_CLK_CFG			0x04
> +#define S3C64XX_SPI_MODE_CFG			0x08
> +#define S3C64XX_SPI_CS_REG			0x0C
> +#define S3C64XX_SPI_INT_EN			0x10
> +#define S3C64XX_SPI_STATUS			0x14
> +#define S3C64XX_SPI_TX_DATA			0x18
> +#define S3C64XX_SPI_RX_DATA			0x1C
> +#define S3C64XX_SPI_PACKET_CNT			0x20
> +#define S3C64XX_SPI_PENDING_CLR			0x24
> +#define S3C64XX_SPI_SWAP_CFG			0x28
> +#define S3C64XX_SPI_FB_CLK			0x2C
> +
> +#define S3C64XX_SPI_CH_HS_EN			BIT(6)	/* High Speed Enable */
> +#define S3C64XX_SPI_CH_SW_RST			BIT(5)
> +#define S3C64XX_SPI_CH_SLAVE			BIT(4)
> +#define S3C64XX_SPI_CPOL_L			BIT(3)
> +#define S3C64XX_SPI_CPHA_B			BIT(2)
> +#define S3C64XX_SPI_CH_RXCH_ON			BIT(1)
> +#define S3C64XX_SPI_CH_TXCH_ON			BIT(0)
> +
> +#define S3C64XX_SPI_CLKSEL_SRCMSK		GENMASK(10, 9)
> +#define S3C64XX_SPI_ENCLK_ENABLE		BIT(8)
> +#define S3C64XX_SPI_PSR_MASK			GENMASK(15, 0)

I find it easier as 0xff to be honest, but I'm not going to be
picky.

> +
> +#define S3C64XX_SPI_MODE_CH_TSZ_MASK		GENMASK(30, 29)
> +#define S3C64XX_SPI_MODE_CH_TSZ_BYTE		0
> +#define S3C64XX_SPI_MODE_CH_TSZ_HALFWORD	1
> +#define S3C64XX_SPI_MODE_CH_TSZ_WORD		2

I personally find this pattern harder to read. Perhaps you can
already define these as FIELD_PREP here.

> +#define S3C64XX_SPI_MAX_TRAILCNT_MASK		GENMASK(28, 19)
> +#define S3C64XX_SPI_MODE_BUS_TSZ_MASK		GENMASK(18, 17)

...

> -#define S3C64XX_SPI_FBCLK_MSK			(3<<0)
> +#define S3C64XX_SPI_FBCLK_MASK			GENMASK(1, 0)

0x3 to me is more understandable than (3<<0) and GENMASK(1, 0).
Bit operation defines should be used when they really simplify
the reading. But when they make it more difficult, then, I don't
see the point.

Overall looks good, though.

Andi
diff mbox series

Patch

diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c
index db1e1d6ee732..16eea56892a2 100644
--- a/drivers/spi/spi-s3c64xx.c
+++ b/drivers/spi/spi-s3c64xx.c
@@ -4,6 +4,7 @@ 
 //      Jaswinder Singh <jassi.brar@samsung.com>
 
 #include <linux/bits.h>
+#include <linux/bitfield.h>
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/dma-mapping.h>
@@ -17,91 +18,91 @@ 
 #include <linux/pm_runtime.h>
 #include <linux/spi/spi.h>
 
-#define MAX_SPI_PORTS		12
-#define S3C64XX_SPI_QUIRK_CS_AUTO	(1 << 1)
-#define AUTOSUSPEND_TIMEOUT	2000
+#define MAX_SPI_PORTS				12
+#define S3C64XX_SPI_QUIRK_CS_AUTO		BIT(1)
+#define AUTOSUSPEND_TIMEOUT			2000
 
 /* Registers and bit-fields */
 
-#define S3C64XX_SPI_CH_CFG		0x00
-#define S3C64XX_SPI_CLK_CFG		0x04
-#define S3C64XX_SPI_MODE_CFG		0x08
-#define S3C64XX_SPI_CS_REG		0x0C
-#define S3C64XX_SPI_INT_EN		0x10
-#define S3C64XX_SPI_STATUS		0x14
-#define S3C64XX_SPI_TX_DATA		0x18
-#define S3C64XX_SPI_RX_DATA		0x1C
-#define S3C64XX_SPI_PACKET_CNT		0x20
-#define S3C64XX_SPI_PENDING_CLR		0x24
-#define S3C64XX_SPI_SWAP_CFG		0x28
-#define S3C64XX_SPI_FB_CLK		0x2C
-
-#define S3C64XX_SPI_CH_HS_EN		(1<<6)	/* High Speed Enable */
-#define S3C64XX_SPI_CH_SW_RST		(1<<5)
-#define S3C64XX_SPI_CH_SLAVE		(1<<4)
-#define S3C64XX_SPI_CPOL_L		(1<<3)
-#define S3C64XX_SPI_CPHA_B		(1<<2)
-#define S3C64XX_SPI_CH_RXCH_ON		(1<<1)
-#define S3C64XX_SPI_CH_TXCH_ON		(1<<0)
-
-#define S3C64XX_SPI_CLKSEL_SRCMSK	(3<<9)
-#define S3C64XX_SPI_CLKSEL_SRCSHFT	9
-#define S3C64XX_SPI_ENCLK_ENABLE	(1<<8)
-#define S3C64XX_SPI_PSR_MASK		0xff
-
-#define S3C64XX_SPI_MODE_CH_TSZ_BYTE		(0<<29)
-#define S3C64XX_SPI_MODE_CH_TSZ_HALFWORD	(1<<29)
-#define S3C64XX_SPI_MODE_CH_TSZ_WORD		(2<<29)
-#define S3C64XX_SPI_MODE_CH_TSZ_MASK		(3<<29)
-#define S3C64XX_SPI_MODE_BUS_TSZ_BYTE		(0<<17)
-#define S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD	(1<<17)
-#define S3C64XX_SPI_MODE_BUS_TSZ_WORD		(2<<17)
-#define S3C64XX_SPI_MODE_BUS_TSZ_MASK		(3<<17)
+#define S3C64XX_SPI_CH_CFG			0x00
+#define S3C64XX_SPI_CLK_CFG			0x04
+#define S3C64XX_SPI_MODE_CFG			0x08
+#define S3C64XX_SPI_CS_REG			0x0C
+#define S3C64XX_SPI_INT_EN			0x10
+#define S3C64XX_SPI_STATUS			0x14
+#define S3C64XX_SPI_TX_DATA			0x18
+#define S3C64XX_SPI_RX_DATA			0x1C
+#define S3C64XX_SPI_PACKET_CNT			0x20
+#define S3C64XX_SPI_PENDING_CLR			0x24
+#define S3C64XX_SPI_SWAP_CFG			0x28
+#define S3C64XX_SPI_FB_CLK			0x2C
+
+#define S3C64XX_SPI_CH_HS_EN			BIT(6)	/* High Speed Enable */
+#define S3C64XX_SPI_CH_SW_RST			BIT(5)
+#define S3C64XX_SPI_CH_SLAVE			BIT(4)
+#define S3C64XX_SPI_CPOL_L			BIT(3)
+#define S3C64XX_SPI_CPHA_B			BIT(2)
+#define S3C64XX_SPI_CH_RXCH_ON			BIT(1)
+#define S3C64XX_SPI_CH_TXCH_ON			BIT(0)
+
+#define S3C64XX_SPI_CLKSEL_SRCMSK		GENMASK(10, 9)
+#define S3C64XX_SPI_ENCLK_ENABLE		BIT(8)
+#define S3C64XX_SPI_PSR_MASK			GENMASK(15, 0)
+
+#define S3C64XX_SPI_MODE_CH_TSZ_MASK		GENMASK(30, 29)
+#define S3C64XX_SPI_MODE_CH_TSZ_BYTE		0
+#define S3C64XX_SPI_MODE_CH_TSZ_HALFWORD	1
+#define S3C64XX_SPI_MODE_CH_TSZ_WORD		2
+#define S3C64XX_SPI_MAX_TRAILCNT_MASK		GENMASK(28, 19)
+#define S3C64XX_SPI_MODE_BUS_TSZ_MASK		GENMASK(18, 17)
+#define S3C64XX_SPI_MODE_BUS_TSZ_BYTE		0
+#define S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD	1
+#define S3C64XX_SPI_MODE_BUS_TSZ_WORD		2
 #define S3C64XX_SPI_MODE_RX_RDY_LVL		GENMASK(16, 11)
-#define S3C64XX_SPI_MODE_RX_RDY_LVL_SHIFT	11
-#define S3C64XX_SPI_MODE_SELF_LOOPBACK		(1<<3)
-#define S3C64XX_SPI_MODE_RXDMA_ON		(1<<2)
-#define S3C64XX_SPI_MODE_TXDMA_ON		(1<<1)
-#define S3C64XX_SPI_MODE_4BURST			(1<<0)
-
-#define S3C64XX_SPI_CS_NSC_CNT_2		(2<<4)
-#define S3C64XX_SPI_CS_AUTO			(1<<1)
-#define S3C64XX_SPI_CS_SIG_INACT		(1<<0)
-
-#define S3C64XX_SPI_INT_TRAILING_EN		(1<<6)
-#define S3C64XX_SPI_INT_RX_OVERRUN_EN		(1<<5)
-#define S3C64XX_SPI_INT_RX_UNDERRUN_EN		(1<<4)
-#define S3C64XX_SPI_INT_TX_OVERRUN_EN		(1<<3)
-#define S3C64XX_SPI_INT_TX_UNDERRUN_EN		(1<<2)
-#define S3C64XX_SPI_INT_RX_FIFORDY_EN		(1<<1)
-#define S3C64XX_SPI_INT_TX_FIFORDY_EN		(1<<0)
-
-#define S3C64XX_SPI_ST_RX_OVERRUN_ERR		(1<<5)
-#define S3C64XX_SPI_ST_RX_UNDERRUN_ERR		(1<<4)
-#define S3C64XX_SPI_ST_TX_OVERRUN_ERR		(1<<3)
-#define S3C64XX_SPI_ST_TX_UNDERRUN_ERR		(1<<2)
-#define S3C64XX_SPI_ST_RX_FIFORDY		(1<<1)
-#define S3C64XX_SPI_ST_TX_FIFORDY		(1<<0)
-
-#define S3C64XX_SPI_PACKET_CNT_EN		(1<<16)
+#define S3C64XX_SPI_MODE_SELF_LOOPBACK		BIT(3)
+#define S3C64XX_SPI_MODE_RXDMA_ON		BIT(2)
+#define S3C64XX_SPI_MODE_TXDMA_ON		BIT(1)
+#define S3C64XX_SPI_MODE_4BURST			BIT(0)
+
+#define S3C64XX_SPI_CS_NSC_CNT_MASK		GENMASK(9, 4)
+#define S3C64XX_SPI_CS_NSC_CNT_2		2
+#define S3C64XX_SPI_CS_AUTO			BIT(1)
+#define S3C64XX_SPI_CS_SIG_INACT		BIT(0)
+
+#define S3C64XX_SPI_INT_TRAILING_EN		BIT(6)
+#define S3C64XX_SPI_INT_RX_OVERRUN_EN		BIT(5)
+#define S3C64XX_SPI_INT_RX_UNDERRUN_EN		BIT(4)
+#define S3C64XX_SPI_INT_TX_OVERRUN_EN		BIT(3)
+#define S3C64XX_SPI_INT_TX_UNDERRUN_EN		BIT(2)
+#define S3C64XX_SPI_INT_RX_FIFORDY_EN		BIT(1)
+#define S3C64XX_SPI_INT_TX_FIFORDY_EN		BIT(0)
+
+#define S3C64XX_SPI_ST_RX_OVERRUN_ERR		BIT(5)
+#define S3C64XX_SPI_ST_RX_UNDERRUN_ERR		BIT(4)
+#define S3C64XX_SPI_ST_TX_OVERRUN_ERR		BIT(3)
+#define S3C64XX_SPI_ST_TX_UNDERRUN_ERR		BIT(2)
+#define S3C64XX_SPI_ST_RX_FIFORDY		BIT(1)
+#define S3C64XX_SPI_ST_TX_FIFORDY		BIT(0)
+
+#define S3C64XX_SPI_PACKET_CNT_EN		BIT(16)
 #define S3C64XX_SPI_PACKET_CNT_MASK		GENMASK(15, 0)
 
-#define S3C64XX_SPI_PND_TX_UNDERRUN_CLR		(1<<4)
-#define S3C64XX_SPI_PND_TX_OVERRUN_CLR		(1<<3)
-#define S3C64XX_SPI_PND_RX_UNDERRUN_CLR		(1<<2)
-#define S3C64XX_SPI_PND_RX_OVERRUN_CLR		(1<<1)
-#define S3C64XX_SPI_PND_TRAILING_CLR		(1<<0)
+#define S3C64XX_SPI_PND_TX_UNDERRUN_CLR		BIT(4)
+#define S3C64XX_SPI_PND_TX_OVERRUN_CLR		BIT(3)
+#define S3C64XX_SPI_PND_RX_UNDERRUN_CLR		BIT(2)
+#define S3C64XX_SPI_PND_RX_OVERRUN_CLR		BIT(1)
+#define S3C64XX_SPI_PND_TRAILING_CLR		BIT(0)
 
-#define S3C64XX_SPI_SWAP_RX_HALF_WORD		(1<<7)
-#define S3C64XX_SPI_SWAP_RX_BYTE		(1<<6)
-#define S3C64XX_SPI_SWAP_RX_BIT			(1<<5)
-#define S3C64XX_SPI_SWAP_RX_EN			(1<<4)
-#define S3C64XX_SPI_SWAP_TX_HALF_WORD		(1<<3)
-#define S3C64XX_SPI_SWAP_TX_BYTE		(1<<2)
-#define S3C64XX_SPI_SWAP_TX_BIT			(1<<1)
-#define S3C64XX_SPI_SWAP_TX_EN			(1<<0)
+#define S3C64XX_SPI_SWAP_RX_HALF_WORD		BIT(7)
+#define S3C64XX_SPI_SWAP_RX_BYTE		BIT(6)
+#define S3C64XX_SPI_SWAP_RX_BIT			BIT(5)
+#define S3C64XX_SPI_SWAP_RX_EN			BIT(4)
+#define S3C64XX_SPI_SWAP_TX_HALF_WORD		BIT(3)
+#define S3C64XX_SPI_SWAP_TX_BYTE		BIT(2)
+#define S3C64XX_SPI_SWAP_TX_BIT			BIT(1)
+#define S3C64XX_SPI_SWAP_TX_EN			BIT(0)
 
-#define S3C64XX_SPI_FBCLK_MSK			(3<<0)
+#define S3C64XX_SPI_FBCLK_MASK			GENMASK(1, 0)
 
 #define FIFO_LVL_MASK(i) ((i)->port_conf->fifo_lvl_mask[i->port_id])
 #define S3C64XX_SPI_ST_TX_DONE(v, i) (((v) & \
@@ -111,18 +112,13 @@ 
 					FIFO_LVL_MASK(i))
 #define FIFO_DEPTH(i) ((FIFO_LVL_MASK(i) >> 1) + 1)
 
-#define S3C64XX_SPI_MAX_TRAILCNT	0x3ff
-#define S3C64XX_SPI_TRAILCNT_OFF	19
-
-#define S3C64XX_SPI_TRAILCNT		S3C64XX_SPI_MAX_TRAILCNT
-
 #define S3C64XX_SPI_POLLING_SIZE	32
 
 #define msecs_to_loops(t) (loops_per_jiffy / 1000 * HZ * t)
 #define is_polling(x)	(x->cntrlr_info->polling)
 
-#define RXBUSY    (1<<2)
-#define TXBUSY    (1<<3)
+#define RXBUSY    BIT(2)
+#define TXBUSY    BIT(3)
 
 struct s3c64xx_spi_dma_data {
 	struct dma_chan *ch;
@@ -341,8 +337,9 @@  static void s3c64xx_spi_set_cs(struct spi_device *spi, bool enable)
 		} else {
 			u32 ssel = readl(sdd->regs + S3C64XX_SPI_CS_REG);
 
-			ssel |= (S3C64XX_SPI_CS_AUTO |
-						S3C64XX_SPI_CS_NSC_CNT_2);
+			ssel |= S3C64XX_SPI_CS_AUTO |
+				FIELD_PREP(S3C64XX_SPI_CS_NSC_CNT_MASK,
+					   S3C64XX_SPI_CS_NSC_CNT_2);
 			writel(ssel, sdd->regs + S3C64XX_SPI_CS_REG);
 		}
 	} else {
@@ -665,16 +662,22 @@  static int s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd)
 
 	switch (sdd->cur_bpw) {
 	case 32:
-		val |= S3C64XX_SPI_MODE_BUS_TSZ_WORD;
-		val |= S3C64XX_SPI_MODE_CH_TSZ_WORD;
+		val |= FIELD_PREP(S3C64XX_SPI_MODE_BUS_TSZ_MASK,
+				  S3C64XX_SPI_MODE_BUS_TSZ_WORD) |
+		       FIELD_PREP(S3C64XX_SPI_MODE_CH_TSZ_MASK,
+				  S3C64XX_SPI_MODE_CH_TSZ_WORD);
 		break;
 	case 16:
-		val |= S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD;
-		val |= S3C64XX_SPI_MODE_CH_TSZ_HALFWORD;
+		val |= FIELD_PREP(S3C64XX_SPI_MODE_BUS_TSZ_MASK,
+				  S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD) |
+		       FIELD_PREP(S3C64XX_SPI_MODE_CH_TSZ_MASK,
+				  S3C64XX_SPI_MODE_CH_TSZ_HALFWORD);
 		break;
 	default:
-		val |= S3C64XX_SPI_MODE_BUS_TSZ_BYTE;
-		val |= S3C64XX_SPI_MODE_CH_TSZ_BYTE;
+		val |= FIELD_PREP(S3C64XX_SPI_MODE_BUS_TSZ_MASK,
+				  S3C64XX_SPI_MODE_BUS_TSZ_BYTE) |
+		       FIELD_PREP(S3C64XX_SPI_MODE_CH_TSZ_MASK,
+				  S3C64XX_SPI_MODE_CH_TSZ_BYTE);
 		break;
 	}
 
@@ -800,7 +803,7 @@  static int s3c64xx_spi_transfer_one(struct spi_controller *host,
 
 			val = readl(sdd->regs + S3C64XX_SPI_MODE_CFG);
 			val &= ~S3C64XX_SPI_MODE_RX_RDY_LVL;
-			val |= (rdy_lv << S3C64XX_SPI_MODE_RX_RDY_LVL_SHIFT);
+			val |= FIELD_PREP(S3C64XX_SPI_MODE_RX_RDY_LVL, rdy_lv);
 			writel(val, sdd->regs + S3C64XX_SPI_MODE_CFG);
 
 			/* Enable FIFO_RDY_EN IRQ */
@@ -1073,8 +1076,8 @@  static void s3c64xx_spi_hwinit(struct s3c64xx_spi_driver_data *sdd)
 	writel(0, regs + S3C64XX_SPI_INT_EN);
 
 	if (!sdd->port_conf->clk_from_cmu)
-		writel(sci->src_clk_nr << S3C64XX_SPI_CLKSEL_SRCSHFT,
-				regs + S3C64XX_SPI_CLK_CFG);
+		writel(FIELD_PREP(S3C64XX_SPI_CLKSEL_SRCMSK, sci->src_clk_nr),
+		       regs + S3C64XX_SPI_CLK_CFG);
 	writel(0, regs + S3C64XX_SPI_MODE_CFG);
 	writel(0, regs + S3C64XX_SPI_PACKET_CNT);
 
@@ -1090,8 +1093,7 @@  static void s3c64xx_spi_hwinit(struct s3c64xx_spi_driver_data *sdd)
 
 	val = readl(regs + S3C64XX_SPI_MODE_CFG);
 	val &= ~S3C64XX_SPI_MODE_4BURST;
-	val &= ~(S3C64XX_SPI_MAX_TRAILCNT << S3C64XX_SPI_TRAILCNT_OFF);
-	val |= (S3C64XX_SPI_TRAILCNT << S3C64XX_SPI_TRAILCNT_OFF);
+	val |= S3C64XX_SPI_MAX_TRAILCNT_MASK;
 	writel(val, regs + S3C64XX_SPI_MODE_CFG);
 
 	s3c64xx_flush_fifo(sdd);