@@ -46,6 +46,59 @@
};
};
+ vdisp: regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "display-power";
+ regulator-min-microvolt = <3600000>;
+ regulator-max-microvolt = <3600000>;
+ /* Collides with LCD E */
+ gpio = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ spi {
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Collides with IDE pins, that's cool (we do not use them) */
+ gpio-sck = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ gpio-miso = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ gpio-mosi = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ /* Collides with pflash CE1, not so cool */
+ cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+ num-chipselects = <1>;
+
+ panel: display@0 {
+ compatible = "ilitek,ili9322";
+ reg = <0>;
+ /* 50 ns min period = 20 MHz */
+ spi-max-frequency = <20000000>;
+ spi-cpol; /* Clock active low */
+
+ /* Panel LM918A01-1A SY-B4-091116-E0199 */
+ width-mm = <65>;
+ height-mm = <50>;
+ ilitek,entry-mode = <11>;
+ ilitek,vreg1out-microvolt = <4600>;
+ ilitek,vcom-high-percent = <91>;
+ ilitek,vcom-amplitude-percent = <114>;
+ ilitek,gamma-correction-neg = <0xa>, <0x5>, <0x7>,
+ <0x7>, <0x7>, <0x5>, <0x1>, <0x6>;
+ ilitek,gamma-correction-pos = <0x7>, <0x7>, <0x3>,
+ <0x2>, <0x3>, <0x5>, <0x7>, <0x2>;
+ vcc-supply = <&vdisp>;
+ iovcc-supply = <&vdisp>;
+ vci-supply = <&vdisp>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
led@7 {
@@ -114,7 +167,16 @@
soc {
flash@30000000 {
- status = "okay";
+ /*
+ * Flash access is by default disabled, because it
+ * collides with the Chip Enable signal for the display
+ * panel, that reuse the parallel flash Chip Select 1
+ * (CS1). Enabling flash makes graphics stop working.
+ *
+ * We might be able to hack around this by letting
+ * GPIO poke around in the flash controller registers.
+ */
+ /* status = "okay"; */
/* 32MB of flash */
reg = <0x30000000 0x02000000>;
@@ -241,5 +303,16 @@
ata@63000000 {
status = "okay";
};
+
+ display-controller@6a000000 {
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
};
};
This adds the TVE200/TVC TV-encoder and the Ilitek ILI9322 panel to the DIR-685 device tree. This brings graphics to this funky router and it is possible to even run a console on its tiny screen. Incidentally this requires us to disable the access to the parallel (NOR) flash, as the communication pins to the panel are shared with the flash memory. To access the flash, a separate kernel with the panel disabled and the flash enabled should be booted. The pin control selecting whether to use the lines cannot be altered at runtime due to hardware constraints. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- ChangeLog v1->v2: - Rename node from "tvc" to "display-controller" DRM developers: I will merge this patch through the ARM SoC tree. It is only included in this series for completion. --- arch/arm/boot/dts/gemini-dlink-dir-685.dts | 75 +++++++++++++++++++++++++++++- 1 file changed, 74 insertions(+), 1 deletion(-)