@@ -31,6 +31,9 @@ [Defines]
[Includes.common]
Include # Root include for the package
+[LibraryClasses]
+ PL011UartLib|Include/Library/PL011UartLib.h
+
[Guids.common]
gArmPlatformTokenSpaceGuid = { 0x9c0aaed4, 0x74c5, 0x4043, { 0xb4, 0x17, 0xa3, 0x22, 0x38, 0x14, 0xce, 0x76 } }
#
new file mode 100644
@@ -0,0 +1,187 @@
+/** @file
+*
+* Copyright (c) 2011-2016, ARM Limited. All rights reserved.
+*
+* This program and the accompanying materials
+* are licensed and made available under the terms and conditions of the BSD License
+* which accompanies this distribution. The full text of the license may be found at
+* http://opensource.org/licenses/bsd-license.php
+*
+* THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
+* WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
+*
+**/
+
+#ifndef __PL011_UART_LIB_H__
+#define __PL011_UART_LIB_H__
+
+#include <Protocol/SerialIo.h>
+
+/**
+
+ Initialise the serial port to the specified settings.
+ All unspecified settings will be set to the default values.
+
+ @param[in] UartBase The base address of the serial device.
+ @param[in] UartClkInHz The clock in Hz for the serial device.
+ Ignored if the PCD PL011UartInteger is not 0
+ @param[in out] BaudRate The baud rate of the serial device. If the
+ baud rate is not supported, the speed will be
+ reduced to the nearest supported one and the
+ variable's value will be updated accordingly.
+ @param[in out] ReceiveFifoDepth The number of characters the device will
+ buffer on input. Value of 0 will use the
+ device's default FIFO depth.
+ @param[in out] Parity If applicable, this is the EFI_PARITY_TYPE
+ that is computed or checked as each character
+ is transmitted or received. If the device
+ does not support parity, the value is the
+ default parity value.
+ @param[in out] DataBits The number of data bits in each character.
+ @param[in out] StopBits If applicable, the EFI_STOP_BITS_TYPE number
+ of stop bits per character.
+ If the device does not support stop bits, the
+ value is the default stop bit value.
+
+ @retval RETURN_SUCCESS All attributes were set correctly on the
+ serial device.
+ @retval RETURN_INVALID_PARAMETER One or more of the attributes has an
+ unsupported value.
+
+**/
+RETURN_STATUS
+EFIAPI
+PL011UartInitializePort (
+ IN UINTN UartBase,
+ IN UINT32 UartClkInHz,
+ IN OUT UINT64 *BaudRate,
+ IN OUT UINT32 *ReceiveFifoDepth,
+ IN OUT EFI_PARITY_TYPE *Parity,
+ IN OUT UINT8 *DataBits,
+ IN OUT EFI_STOP_BITS_TYPE *StopBits
+ );
+
+/**
+
+ Assert or deassert the control signals on a serial port.
+ The following control signals are set according their bit settings :
+ . Request to Send
+ . Data Terminal Ready
+
+ @param[in] UartBase UART registers base address
+ @param[in] Control The following bits are taken into account :
+ . EFI_SERIAL_REQUEST_TO_SEND : assert/deassert the
+ "Request To Send" control signal if this bit is
+ equal to one/zero.
+ . EFI_SERIAL_DATA_TERMINAL_READY : assert/deassert
+ the "Data Terminal Ready" control signal if this
+ bit is equal to one/zero.
+ . EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE : enable/disable
+ the hardware loopback if this bit is equal to
+ one/zero.
+ . EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE : not supported.
+ . EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE : enable/
+ disable the hardware flow control based on CTS (Clear
+ To Send) and RTS (Ready To Send) control signals.
+
+ @retval RETURN_SUCCESS The new control bits were set on the device.
+ @retval RETURN_UNSUPPORTED The device does not support this operation.
+
+**/
+RETURN_STATUS
+EFIAPI
+PL011UartSetControl (
+ IN UINTN UartBase,
+ IN UINT32 Control
+ );
+
+/**
+
+ Retrieve the status of the control bits on a serial device.
+
+ @param[in] UartBase UART registers base address
+ @param[out] Control Status of the control bits on a serial device :
+
+ . EFI_SERIAL_DATA_CLEAR_TO_SEND,
+ EFI_SERIAL_DATA_SET_READY,
+ EFI_SERIAL_RING_INDICATE,
+ EFI_SERIAL_CARRIER_DETECT,
+ EFI_SERIAL_REQUEST_TO_SEND,
+ EFI_SERIAL_DATA_TERMINAL_READY
+ are all related to the DTE (Data Terminal Equipment)
+ and DCE (Data Communication Equipment) modes of
+ operation of the serial device.
+ . EFI_SERIAL_INPUT_BUFFER_EMPTY : equal to one if the
+ receive buffer is empty, 0 otherwise.
+ . EFI_SERIAL_OUTPUT_BUFFER_EMPTY : equal to one if the
+ transmit buffer is empty, 0 otherwise.
+ . EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE : equal to one if
+ the hardware loopback is enabled (the ouput feeds the
+ receive buffer), 0 otherwise.
+ . EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE : equal to one if
+ a loopback is accomplished by software, 0 otherwise.
+ . EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE : equal to
+ one if the hardware flow control based on CTS (Clear
+ To Send) and RTS (Ready To Send) control signals is
+ enabled, 0 otherwise.
+
+ @retval RETURN_SUCCESS The control bits were read from the serial device.
+
+**/
+RETURN_STATUS
+EFIAPI
+PL011UartGetControl (
+ IN UINTN UartBase,
+ OUT UINT32 *Control
+ );
+
+/**
+ Write data to serial device.
+
+ @param Buffer Point of data buffer which need to be written.
+ @param NumberOfBytes Number of output bytes which are cached in Buffer.
+
+ @retval 0 Write data failed.
+ @retval !0 Actual number of bytes written to serial device.
+
+**/
+UINTN
+EFIAPI
+PL011UartWrite (
+ IN UINTN UartBase,
+ IN UINT8 *Buffer,
+ IN UINTN NumberOfBytes
+ );
+
+/**
+ Read data from serial device and save the data in buffer.
+
+ @param Buffer Point of data buffer which need to be written.
+ @param NumberOfBytes Number of output bytes which are cached in Buffer.
+
+ @retval 0 Read data failed.
+ @retval !0 Actual number of bytes read from serial device.
+
+**/
+UINTN
+EFIAPI
+PL011UartRead (
+ IN UINTN UartBase,
+ OUT UINT8 *Buffer,
+ IN UINTN NumberOfBytes
+ );
+
+/**
+ Check to see if any data is available to be read from the debug device.
+
+ @retval TRUE At least one byte of data is available to be read
+ @retval FALSE No data is available to be read
+
+**/
+BOOLEAN
+EFIAPI
+PL011UartPoll (
+ IN UINTN UartBase
+ );
+
+#endif
@@ -15,14 +15,13 @@
**/
-#include <Base.h>
+#include <Uefi.h>
#include <Library/IoLib.h>
#include <Library/PcdLib.h>
+#include <Library/PL011UartLib.h>
#include <Library/SerialPortLib.h>
-#include <Drivers/PL011Uart.h>
-
/** Initialise the serial device hardware with default settings.
@retval RETURN_SUCCESS The serial device was initialised.
new file mode 100644
@@ -0,0 +1,120 @@
+/** @file
+*
+* Copyright (c) 2011-2016, ARM Limited. All rights reserved.
+*
+* This program and the accompanying materials
+* are licensed and made available under the terms and conditions of the BSD License
+* which accompanies this distribution. The full text of the license may be found at
+* http://opensource.org/licenses/bsd-license.php
+*
+* THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
+* WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
+*
+**/
+
+#ifndef __PL011_UART_H__
+#define __PL011_UART_H__
+
+#define PL011_VARIANT_ZTE 1
+
+// PL011 Registers
+#if FixedPcdGet8 (PL011UartRegOffsetVariant) == PL011_VARIANT_ZTE
+#define UARTDR 0x004
+#define UARTRSR 0x010
+#define UARTECR 0x010
+#define UARTFR 0x014
+#define UARTIBRD 0x024
+#define UARTFBRD 0x028
+#define UARTLCR_H 0x030
+#define UARTCR 0x034
+#define UARTIFLS 0x038
+#define UARTIMSC 0x040
+#define UARTRIS 0x044
+#define UARTMIS 0x048
+#define UARTICR 0x04c
+#define UARTDMACR 0x050
+#else
+#define UARTDR 0x000
+#define UARTRSR 0x004
+#define UARTECR 0x004
+#define UARTFR 0x018
+#define UARTILPR 0x020
+#define UARTIBRD 0x024
+#define UARTFBRD 0x028
+#define UARTLCR_H 0x02C
+#define UARTCR 0x030
+#define UARTIFLS 0x034
+#define UARTIMSC 0x038
+#define UARTRIS 0x03C
+#define UARTMIS 0x040
+#define UARTICR 0x044
+#define UARTDMACR 0x048
+#endif
+
+#define UARTPID0 0xFE0
+#define UARTPID1 0xFE4
+#define UARTPID2 0xFE8
+#define UARTPID3 0xFEC
+
+// Data status bits
+#define UART_DATA_ERROR_MASK 0x0F00
+
+// Status reg bits
+#define UART_STATUS_ERROR_MASK 0x0F
+
+// Flag reg bits
+#if FixedPcdGet8 (PL011UartRegOffsetVariant) == PL011_VARIANT_ZTE
+#define PL011_UARTFR_RI (1 << 0) // Ring indicator
+#define PL011_UARTFR_TXFE (1 << 7) // Transmit FIFO empty
+#define PL011_UARTFR_RXFF (1 << 6) // Receive FIFO full
+#define PL011_UARTFR_TXFF (1 << 5) // Transmit FIFO full
+#define PL011_UARTFR_RXFE (1 << 4) // Receive FIFO empty
+#define PL011_UARTFR_BUSY (1 << 8) // UART busy
+#define PL011_UARTFR_DCD (1 << 2) // Data carrier detect
+#define PL011_UARTFR_DSR (1 << 3) // Data set ready
+#define PL011_UARTFR_CTS (1 << 1) // Clear to send
+#else
+#define PL011_UARTFR_RI (1 << 8) // Ring indicator
+#define PL011_UARTFR_TXFE (1 << 7) // Transmit FIFO empty
+#define PL011_UARTFR_RXFF (1 << 6) // Receive FIFO full
+#define PL011_UARTFR_TXFF (1 << 5) // Transmit FIFO full
+#define PL011_UARTFR_RXFE (1 << 4) // Receive FIFO empty
+#define PL011_UARTFR_BUSY (1 << 3) // UART busy
+#define PL011_UARTFR_DCD (1 << 2) // Data carrier detect
+#define PL011_UARTFR_DSR (1 << 1) // Data set ready
+#define PL011_UARTFR_CTS (1 << 0) // Clear to send
+#endif
+
+// Flag reg bits - alternative names
+#define UART_TX_EMPTY_FLAG_MASK PL011_UARTFR_TXFE
+#define UART_RX_FULL_FLAG_MASK PL011_UARTFR_RXFF
+#define UART_TX_FULL_FLAG_MASK PL011_UARTFR_TXFF
+#define UART_RX_EMPTY_FLAG_MASK PL011_UARTFR_RXFE
+#define UART_BUSY_FLAG_MASK PL011_UARTFR_BUSY
+
+// Control reg bits
+#define PL011_UARTCR_CTSEN (1 << 15) // CTS hardware flow control enable
+#define PL011_UARTCR_RTSEN (1 << 14) // RTS hardware flow control enable
+#define PL011_UARTCR_RTS (1 << 11) // Request to send
+#define PL011_UARTCR_DTR (1 << 10) // Data transmit ready.
+#define PL011_UARTCR_RXE (1 << 9) // Receive enable
+#define PL011_UARTCR_TXE (1 << 8) // Transmit enable
+#define PL011_UARTCR_LBE (1 << 7) // Loopback enable
+#define PL011_UARTCR_UARTEN (1 << 0) // UART Enable
+
+// Line Control Register Bits
+#define PL011_UARTLCR_H_SPS (1 << 7) // Stick parity select
+#define PL011_UARTLCR_H_WLEN_8 (3 << 5)
+#define PL011_UARTLCR_H_WLEN_7 (2 << 5)
+#define PL011_UARTLCR_H_WLEN_6 (1 << 5)
+#define PL011_UARTLCR_H_WLEN_5 (0 << 5)
+#define PL011_UARTLCR_H_FEN (1 << 4) // FIFOs Enable
+#define PL011_UARTLCR_H_STP2 (1 << 3) // Two stop bits select
+#define PL011_UARTLCR_H_EPS (1 << 2) // Even parity select
+#define PL011_UARTLCR_H_PEN (1 << 1) // Parity Enable
+#define PL011_UARTLCR_H_BRK (1 << 0) // Send break
+
+#define PL011_UARTPID2_VER(X) (((X) >> 4) & 0xF)
+#define PL011_VER_R1P4 0x2
+
+#endif
new file mode 100644
@@ -0,0 +1,474 @@
+/** @file
+ Serial I/O Port library functions with no library constructor/destructor
+
+ Copyright (c) 2008 - 2010, Apple Inc. All rights reserved.<BR>
+ Copyright (c) 2011 - 2016, ARM Ltd. All rights reserved.<BR>
+
+ This program and the accompanying materials
+ are licensed and made available under the terms and conditions of the BSD License
+ which accompanies this distribution. The full text of the license may be found at
+ http://opensource.org/licenses/bsd-license.php
+
+ THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
+ WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
+
+**/
+
+#include <Uefi.h>
+
+#include <Library/DebugLib.h>
+#include <Library/IoLib.h>
+#include <Library/PcdLib.h>
+
+#include <Protocol/SerialIo.h>
+
+#include "PL011Uart.h"
+
+#define FRACTION_PART_SIZE_IN_BITS 6
+#define FRACTION_PART_MASK ((1 << FRACTION_PART_SIZE_IN_BITS) - 1)
+
+//
+// EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE is the only
+// control bit that is not supported.
+//
+STATIC CONST UINT32 mInvalidControlBits = EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE;
+
+/**
+
+ Initialise the serial port to the specified settings.
+ The serial port is re-configured only if the specified settings
+ are different from the current settings.
+ All unspecified settings will be set to the default values.
+
+ @param UartBase The base address of the serial device.
+ @param UartClkInHz The clock in Hz for the serial device.
+ Ignored if the PCD PL011UartInteger is not 0
+ @param BaudRate The baud rate of the serial device. If the
+ baud rate is not supported, the speed will be
+ reduced to the nearest supported one and the
+ variable's value will be updated accordingly.
+ @param ReceiveFifoDepth The number of characters the device will
+ buffer on input. Value of 0 will use the
+ device's default FIFO depth.
+ @param Parity If applicable, this is the EFI_PARITY_TYPE
+ that is computed or checked as each character
+ is transmitted or received. If the device
+ does not support parity, the value is the
+ default parity value.
+ @param DataBits The number of data bits in each character.
+ @param StopBits If applicable, the EFI_STOP_BITS_TYPE number
+ of stop bits per character.
+ If the device does not support stop bits, the
+ value is the default stop bit value.
+
+ @retval RETURN_SUCCESS All attributes were set correctly on the
+ serial device.
+ @retval RETURN_INVALID_PARAMETER One or more of the attributes has an
+ unsupported value.
+
+**/
+RETURN_STATUS
+EFIAPI
+PL011UartInitializePort (
+ IN UINTN UartBase,
+ IN UINT32 UartClkInHz,
+ IN OUT UINT64 *BaudRate,
+ IN OUT UINT32 *ReceiveFifoDepth,
+ IN OUT EFI_PARITY_TYPE *Parity,
+ IN OUT UINT8 *DataBits,
+ IN OUT EFI_STOP_BITS_TYPE *StopBits
+ )
+{
+ UINT32 LineControl;
+ UINT32 Divisor;
+ UINT32 Integer;
+ UINT32 Fractional;
+ UINT32 HardwareFifoDepth;
+
+ HardwareFifoDepth = (PL011_UARTPID2_VER (MmioRead32 (UartBase + UARTPID2)) \
+ > PL011_VER_R1P4) \
+ ? 32 : 16 ;
+ // The PL011 supports a buffer of 1, 16 or 32 chars. Therefore we can accept
+ // 1 char buffer as the minimum FIFO size. Because everything can be rounded
+ // down, there is no maximum FIFO size.
+ if ((*ReceiveFifoDepth == 0) || (*ReceiveFifoDepth >= HardwareFifoDepth)) {
+ // Enable FIFO
+ LineControl = PL011_UARTLCR_H_FEN;
+ *ReceiveFifoDepth = HardwareFifoDepth;
+ } else {
+ // Disable FIFO
+ LineControl = 0;
+ // Nothing else to do. 1 byte FIFO is default.
+ *ReceiveFifoDepth = 1;
+ }
+
+ //
+ // Parity
+ //
+ switch (*Parity) {
+ case DefaultParity:
+ *Parity = NoParity;
+ case NoParity:
+ // Nothing to do. Parity is disabled by default.
+ break;
+ case EvenParity:
+ LineControl |= (PL011_UARTLCR_H_PEN | PL011_UARTLCR_H_EPS);
+ break;
+ case OddParity:
+ LineControl |= PL011_UARTLCR_H_PEN;
+ break;
+ case MarkParity:
+ LineControl |= ( PL011_UARTLCR_H_PEN \
+ | PL011_UARTLCR_H_SPS \
+ | PL011_UARTLCR_H_EPS);
+ break;
+ case SpaceParity:
+ LineControl |= (PL011_UARTLCR_H_PEN | PL011_UARTLCR_H_SPS);
+ break;
+ default:
+ return RETURN_INVALID_PARAMETER;
+ }
+
+ //
+ // Data Bits
+ //
+ switch (*DataBits) {
+ case 0:
+ *DataBits = 8;
+ case 8:
+ LineControl |= PL011_UARTLCR_H_WLEN_8;
+ break;
+ case 7:
+ LineControl |= PL011_UARTLCR_H_WLEN_7;
+ break;
+ case 6:
+ LineControl |= PL011_UARTLCR_H_WLEN_6;
+ break;
+ case 5:
+ LineControl |= PL011_UARTLCR_H_WLEN_5;
+ break;
+ default:
+ return RETURN_INVALID_PARAMETER;
+ }
+
+ //
+ // Stop Bits
+ //
+ switch (*StopBits) {
+ case DefaultStopBits:
+ *StopBits = OneStopBit;
+ case OneStopBit:
+ // Nothing to do. One stop bit is enabled by default.
+ break;
+ case TwoStopBits:
+ LineControl |= PL011_UARTLCR_H_STP2;
+ break;
+ case OneFiveStopBits:
+ // Only 1 or 2 stop bits are supported
+ default:
+ return RETURN_INVALID_PARAMETER;
+ }
+
+ // Don't send the LineControl value to the PL011 yet,
+ // wait until after the Baud Rate setting.
+ // This ensures we do not mess up the UART settings halfway through
+ // in the rare case when there is an error with the Baud Rate.
+
+ //
+ // Baud Rate
+ //
+
+ // If PL011 Integer value has been defined then always ignore the BAUD rate
+ if (FixedPcdGet32 (PL011UartInteger) != 0) {
+ Integer = FixedPcdGet32 (PL011UartInteger);
+ Fractional = FixedPcdGet32 (PL011UartFractional);
+ } else {
+ // If BAUD rate is zero then replace it with the system default value
+ if (*BaudRate == 0) {
+ *BaudRate = FixedPcdGet32 (PcdSerialBaudRate);
+ if (*BaudRate == 0) {
+ return RETURN_INVALID_PARAMETER;
+ }
+ }
+ if (0 == UartClkInHz) {
+ return RETURN_INVALID_PARAMETER;
+ }
+
+ Divisor = (UartClkInHz * 4) / *BaudRate;
+ Integer = Divisor >> FRACTION_PART_SIZE_IN_BITS;
+ Fractional = Divisor & FRACTION_PART_MASK;
+ }
+
+ //
+ // If PL011 is already initialized, check the current settings
+ // and re-initialize only if the settings are different.
+ //
+ if (((MmioRead32 (UartBase + UARTCR) & PL011_UARTCR_UARTEN) != 0) &&
+ (MmioRead32 (UartBase + UARTLCR_H) == LineControl) &&
+ (MmioRead32 (UartBase + UARTIBRD) == Integer) &&
+ (MmioRead32 (UartBase + UARTFBRD) == Fractional)) {
+ // Nothing to do - already initialized with correct attributes
+ return RETURN_SUCCESS;
+ }
+
+ // Wait for the end of transmission
+ while ((MmioRead32 (UartBase + UARTFR) & PL011_UARTFR_TXFE) == 0);
+
+ // Disable UART: "The UARTLCR_H, UARTIBRD, and UARTFBRD registers must not be changed
+ // when the UART is enabled"
+ MmioWrite32 (UartBase + UARTCR, 0);
+
+ // Set Baud Rate Registers
+ MmioWrite32 (UartBase + UARTIBRD, Integer);
+ MmioWrite32 (UartBase + UARTFBRD, Fractional);
+
+ // No parity, 1 stop, no fifo, 8 data bits
+ MmioWrite32 (UartBase + UARTLCR_H, LineControl);
+
+ // Clear any pending errors
+ MmioWrite32 (UartBase + UARTECR, 0);
+
+ // Enable Tx, Rx, and UART overall
+ MmioWrite32 (UartBase + UARTCR,
+ PL011_UARTCR_RXE | PL011_UARTCR_TXE | PL011_UARTCR_UARTEN);
+
+ return RETURN_SUCCESS;
+}
+
+/**
+
+ Assert or deassert the control signals on a serial port.
+ The following control signals are set according their bit settings :
+ . Request to Send
+ . Data Terminal Ready
+
+ @param[in] UartBase UART registers base address
+ @param[in] Control The following bits are taken into account :
+ . EFI_SERIAL_REQUEST_TO_SEND : assert/deassert the
+ "Request To Send" control signal if this bit is
+ equal to one/zero.
+ . EFI_SERIAL_DATA_TERMINAL_READY : assert/deassert
+ the "Data Terminal Ready" control signal if this
+ bit is equal to one/zero.
+ . EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE : enable/disable
+ the hardware loopback if this bit is equal to
+ one/zero.
+ . EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE : not supported.
+ . EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE : enable/
+ disable the hardware flow control based on CTS (Clear
+ To Send) and RTS (Ready To Send) control signals.
+
+ @retval RETURN_SUCCESS The new control bits were set on the device.
+ @retval RETURN_UNSUPPORTED The device does not support this operation.
+
+**/
+RETURN_STATUS
+EFIAPI
+PL011UartSetControl (
+ IN UINTN UartBase,
+ IN UINT32 Control
+ )
+{
+ UINT32 Bits;
+
+ if (Control & (mInvalidControlBits)) {
+ return RETURN_UNSUPPORTED;
+ }
+
+ Bits = MmioRead32 (UartBase + UARTCR);
+
+ if (Control & EFI_SERIAL_REQUEST_TO_SEND) {
+ Bits |= PL011_UARTCR_RTS;
+ } else {
+ Bits &= ~PL011_UARTCR_RTS;
+ }
+
+ if (Control & EFI_SERIAL_DATA_TERMINAL_READY) {
+ Bits |= PL011_UARTCR_DTR;
+ } else {
+ Bits &= ~PL011_UARTCR_DTR;
+ }
+
+ if (Control & EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE) {
+ Bits |= PL011_UARTCR_LBE;
+ } else {
+ Bits &= ~PL011_UARTCR_LBE;
+ }
+
+ if (Control & EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE) {
+ Bits |= (PL011_UARTCR_CTSEN | PL011_UARTCR_RTSEN);
+ } else {
+ Bits &= ~(PL011_UARTCR_CTSEN | PL011_UARTCR_RTSEN);
+ }
+
+ MmioWrite32 (UartBase + UARTCR, Bits);
+
+ return RETURN_SUCCESS;
+}
+
+/**
+
+ Retrieve the status of the control bits on a serial device.
+
+ @param[in] UartBase UART registers base address
+ @param[out] Control Status of the control bits on a serial device :
+
+ . EFI_SERIAL_DATA_CLEAR_TO_SEND,
+ EFI_SERIAL_DATA_SET_READY,
+ EFI_SERIAL_RING_INDICATE,
+ EFI_SERIAL_CARRIER_DETECT,
+ EFI_SERIAL_REQUEST_TO_SEND,
+ EFI_SERIAL_DATA_TERMINAL_READY
+ are all related to the DTE (Data Terminal Equipment)
+ and DCE (Data Communication Equipment) modes of
+ operation of the serial device.
+ . EFI_SERIAL_INPUT_BUFFER_EMPTY : equal to one if the
+ receive buffer is empty, 0 otherwise.
+ . EFI_SERIAL_OUTPUT_BUFFER_EMPTY : equal to one if the
+ transmit buffer is empty, 0 otherwise.
+ . EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE : equal to one if
+ the hardware loopback is enabled (the ouput feeds the
+ receive buffer), 0 otherwise.
+ . EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE : equal to one if
+ a loopback is accomplished by software, 0 otherwise.
+ . EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE : equal to
+ one if the hardware flow control based on CTS (Clear
+ To Send) and RTS (Ready To Send) control signals is
+ enabled, 0 otherwise.
+
+ @retval RETURN_SUCCESS The control bits were read from the serial device.
+
+**/
+RETURN_STATUS
+EFIAPI
+PL011UartGetControl (
+ IN UINTN UartBase,
+ OUT UINT32 *Control
+ )
+{
+ UINT32 FlagRegister;
+ UINT32 ControlRegister;
+
+
+ FlagRegister = MmioRead32 (UartBase + UARTFR);
+ ControlRegister = MmioRead32 (UartBase + UARTCR);
+
+ *Control = 0;
+
+ if ((FlagRegister & PL011_UARTFR_CTS) == PL011_UARTFR_CTS) {
+ *Control |= EFI_SERIAL_CLEAR_TO_SEND;
+ }
+
+ if ((FlagRegister & PL011_UARTFR_DSR) == PL011_UARTFR_DSR) {
+ *Control |= EFI_SERIAL_DATA_SET_READY;
+ }
+
+ if ((FlagRegister & PL011_UARTFR_RI) == PL011_UARTFR_RI) {
+ *Control |= EFI_SERIAL_RING_INDICATE;
+ }
+
+ if ((FlagRegister & PL011_UARTFR_DCD) == PL011_UARTFR_DCD) {
+ *Control |= EFI_SERIAL_CARRIER_DETECT;
+ }
+
+ if ((ControlRegister & PL011_UARTCR_RTS) == PL011_UARTCR_RTS) {
+ *Control |= EFI_SERIAL_REQUEST_TO_SEND;
+ }
+
+ if ((ControlRegister & PL011_UARTCR_DTR) == PL011_UARTCR_DTR) {
+ *Control |= EFI_SERIAL_DATA_TERMINAL_READY;
+ }
+
+ if ((FlagRegister & PL011_UARTFR_RXFE) == PL011_UARTFR_RXFE) {
+ *Control |= EFI_SERIAL_INPUT_BUFFER_EMPTY;
+ }
+
+ if ((FlagRegister & PL011_UARTFR_TXFE) == PL011_UARTFR_TXFE) {
+ *Control |= EFI_SERIAL_OUTPUT_BUFFER_EMPTY;
+ }
+
+ if ((ControlRegister & (PL011_UARTCR_CTSEN | PL011_UARTCR_RTSEN))
+ == (PL011_UARTCR_CTSEN | PL011_UARTCR_RTSEN)) {
+ *Control |= EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE;
+ }
+
+ if ((ControlRegister & PL011_UARTCR_LBE) == PL011_UARTCR_LBE) {
+ *Control |= EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE;
+ }
+
+ return RETURN_SUCCESS;
+}
+
+/**
+ Write data to serial device.
+
+ @param Buffer Point of data buffer which need to be written.
+ @param NumberOfBytes Number of output bytes which are cached in Buffer.
+
+ @retval 0 Write data failed.
+ @retval !0 Actual number of bytes written to serial device.
+
+**/
+UINTN
+EFIAPI
+PL011UartWrite (
+ IN UINTN UartBase,
+ IN UINT8 *Buffer,
+ IN UINTN NumberOfBytes
+ )
+{
+ UINT8* CONST Final = &Buffer[NumberOfBytes];
+
+ while (Buffer < Final) {
+ // Wait until UART able to accept another char
+ while ((MmioRead32 (UartBase + UARTFR) & UART_TX_FULL_FLAG_MASK));
+
+ MmioWrite8 (UartBase + UARTDR, *Buffer++);
+ }
+
+ return NumberOfBytes;
+}
+
+/**
+ Read data from serial device and save the data in buffer.
+
+ @param Buffer Point of data buffer which need to be written.
+ @param NumberOfBytes Number of output bytes which are cached in Buffer.
+
+ @retval 0 Read data failed.
+ @retval !0 Actual number of bytes read from serial device.
+
+**/
+UINTN
+EFIAPI
+PL011UartRead (
+ IN UINTN UartBase,
+ OUT UINT8 *Buffer,
+ IN UINTN NumberOfBytes
+ )
+{
+ UINTN Count;
+
+ for (Count = 0; Count < NumberOfBytes; Count++, Buffer++) {
+ while ((MmioRead32 (UartBase + UARTFR) & UART_RX_EMPTY_FLAG_MASK) != 0);
+ *Buffer = MmioRead8 (UartBase + UARTDR);
+ }
+
+ return NumberOfBytes;
+}
+
+/**
+ Check to see if any data is available to be read from the debug device.
+
+ @retval TRUE At least one byte of data is available to be read
+ @retval FALSE No data is available to be read
+
+**/
+BOOLEAN
+EFIAPI
+PL011UartPoll (
+ IN UINTN UartBase
+ )
+{
+ return ((MmioRead32 (UartBase + UARTFR) & UART_RX_EMPTY_FLAG_MASK) == 0);
+}
new file mode 100644
@@ -0,0 +1,43 @@
+#/** @file
+#
+# Component description file for PL011Uart module
+#
+# Copyright (c) 2011-2016, ARM Ltd. All rights reserved.<BR>
+#
+# This program and the accompanying materials
+# are licensed and made available under the terms and conditions of the BSD License
+# which accompanies this distribution. The full text of the license may be found at
+# http://opensource.org/licenses/bsd-license.php
+#
+# THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
+# WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
+#
+#**/
+
+[Defines]
+ INF_VERSION = 0x00010005
+ BASE_NAME = PL011UartLib
+ FILE_GUID = 6a2c5714-8910-44f0-861f-804abc18ce39
+ MODULE_TYPE = BASE
+ VERSION_STRING = 1.0
+ LIBRARY_CLASS = PL011UartLib
+
+[Sources.common]
+ PL011Uart.h
+ PL011UartLib.c
+
+[LibraryClasses]
+ DebugLib
+ IoLib
+
+[Packages]
+ MdePkg/MdePkg.dec
+ MdeModulePkg/MdeModulePkg.dec
+ ArmPlatformPkg/ArmPlatformPkg.dec
+
+[FixedPcd]
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialBaudRate
+
+ gArmPlatformTokenSpaceGuid.PL011UartInteger
+ gArmPlatformTokenSpaceGuid.PL011UartFractional
+ gArmPlatformTokenSpaceGuid.PL011UartRegOffsetVariant
The PL011 code in ArmPlatformPkg is organized in a weird way: there is a single PL011Uart.h header file under Include/Drivers containing both register definitions and function entry points. The PL011Uart library itself is in Drivers/ but it is actually a library. So let's clean this up: add a new PL011UartLib library class and associated header file containing only the library prototypes, and move the library itself under Library/ using a new GUID, with the register definitions moved into a local header file. Contributed-under: TianoCore Contribution Agreement 1.1 Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> --- ArmPlatformPkg/ArmPlatformPkg.dec | 3 + ArmPlatformPkg/Include/Library/PL011UartLib.h | 187 ++++++++ ArmPlatformPkg/Library/PL011SerialPortLib/PL011SerialPortLib.c | 5 +- ArmPlatformPkg/Library/PL011UartLib/PL011Uart.h | 120 +++++ ArmPlatformPkg/Library/PL011UartLib/PL011UartLib.c | 474 ++++++++++++++++++++ ArmPlatformPkg/Library/PL011UartLib/PL011UartLib.inf | 43 ++ 6 files changed, 829 insertions(+), 3 deletions(-) -- 2.11.0 _______________________________________________ edk2-devel mailing list edk2-devel@lists.01.org https://lists.01.org/mailman/listinfo/edk2-devel