@@ -24,6 +24,8 @@
#include <linux/mfd/abx500/ab8500.h>
#include <linux/regulator/ab8500.h>
#include <linux/regulator/fixed.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/gpio-regulator.h>
#include <linux/mfd/tc3589x.h>
#include <linux/mfd/tps6105x.h>
#include <linux/mfd/abx500/ab8500-gpio.h>
@@ -91,6 +93,54 @@ static struct platform_device snowball_gpio_en_3v3_regulator_dev = {
},
};
+static struct regulator_consumer_supply sdi0_reg_consumers[] = {
+ REGULATOR_SUPPLY("vqmmc", NULL),
+};
+
+static struct regulator_init_data sdi0_reg_init_data = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 3300000,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE|REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(sdi0_reg_consumers),
+ .consumer_supplies = sdi0_reg_consumers,
+};
+
+/* Dynamically populated. */
+static struct gpio sdi0_reg_gpios[] = {
+ { 0, GPIOF_OUT_INIT_LOW, "mmci_vsel" },
+};
+
+static struct gpio_regulator_state sdi0_reg_states[] = {
+ { .value = 3300000, .gpios = (0 << 0) },
+ { .value = 1800000, .gpios = (1 << 0) },
+};
+
+static struct gpio_regulator_config sdi0_reg_info = {
+ .supply_name = "mmci-reg",
+
+ .enable_high = 1,
+ .enabled_at_boot = 0,
+
+ .gpios = sdi0_reg_gpios,
+ .nr_gpios = ARRAY_SIZE(sdi0_reg_gpios),
+
+ .states = sdi0_reg_states,
+ .nr_states = ARRAY_SIZE(sdi0_reg_states),
+
+ .type = REGULATOR_VOLTAGE,
+ .init_data = &sdi0_reg_init_data,
+};
+
+static struct platform_device sdi0_regulator = {
+ .name = "gpio-regulator",
+ .id = -1,
+ .dev = {
+ .platform_data = &sdi0_reg_info,
+ },
+};
+
static struct ab8500_gpio_platform_data ab8500_gpio_pdata = {
.gpio_base = MOP500_AB8500_PIN_GPIO(1),
.irq_base = MOP500_AB8500_VIR_GPIO_IRQ_BASE,
@@ -440,6 +490,7 @@ static struct hash_platform_data u8500_hash1_platform_data = {
/* add any platform devices here - TODO */
static struct platform_device *mop500_platform_devs[] __initdata = {
&mop500_gpio_keys_device,
+ &sdi0_regulator,
};
#ifdef CONFIG_STE_DMA40
@@ -581,6 +632,7 @@ static struct platform_device *snowball_platform_devs[] __initdata = {
&snowball_key_dev,
&snowball_sbnet_dev,
&snowball_gpio_en_3v3_regulator_dev,
+ &sdi0_regulator,
};
static void __init mop500_init_machine(void)
@@ -591,6 +643,9 @@ static void __init mop500_init_machine(void)
mop500_gpio_keys[0].gpio = GPIO_PROX_SENSOR;
+ sdi0_reg_info.enable_gpio = GPIO_SDMMC_EN;
+ sdi0_reg_info.gpios[0].gpio = GPIO_SDMMC_1V8_3V_SEL;
+
mop500_pinmaps_init();
parent = u8500_init_devices(&ab8500_platdata);
@@ -623,6 +678,9 @@ static void __init snowball_init_machine(void)
struct device *parent = NULL;
int i;
+ sdi0_reg_info.enable_gpio = SNOWBALL_SDMMC_EN_GPIO;
+ sdi0_reg_info.gpios[0].gpio = SNOWBALL_SDMMC_1V8_3V_GPIO;
+
snowball_pinmaps_init();
parent = u8500_init_devices(&ab8500_platdata);
@@ -655,6 +713,9 @@ static void __init hrefv60_init_machine(void)
*/
mop500_gpio_keys[0].gpio = HREFV60_PROX_SENSE_GPIO;
+ sdi0_reg_info.enable_gpio = HREFV60_SDMMC_EN_GPIO;
+ sdi0_reg_info.gpios[0].gpio = HREFV60_SDMMC_1V8_3V_GPIO;
+
hrefv60_pinmaps_init();
parent = u8500_init_devices(&ab8500_platdata);
To prevent lots of unnecessary call-backs into platform code, we're now using the GPIO regulator framework to control the 'enable' (en) and 'voltage select' (vsel) GPIO pins which in turn control the MMCI's secondary regulator settings. This already works with Device Tree, but when booting with ATAGs we need to register it as a platform device. Signed-off-by: Lee Jones <lee.jones@linaro.org> --- arch/arm/mach-ux500/board-mop500.c | 61 ++++++++++++++++++++++++++++++++++++ 1 file changed, 61 insertions(+)