diff mbox series

[v3,12/14] ARM: dts: imx7s-warp: add ov2680 sensor node

Message ID 20180507162152.2545-13-rui.silva@linaro.org
State New
Headers show
Series media: staging/imx7: add i.MX7 media driver | expand

Commit Message

Rui Miguel Silva May 7, 2018, 4:21 p.m. UTC 
Warp7 comes with a Omnivision OV2680 sensor, add the node here to make complete
the camera data path for this system. Add the needed regulator to the analog
voltage supply.

Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>

---
 arch/arm/boot/dts/imx7s-warp.dts | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)

-- 
2.17.0

Comments

Fabio Estevam May 8, 2018, 1:28 p.m. UTC | #1 
Hi Rui,

On Mon, May 7, 2018 at 1:21 PM, Rui Miguel Silva <rui.silva@linaro.org> wrote:

> +       reg_peri_3p15v: regulator-peri-3p15v {

> +               compatible = "regulator-fixed";

> +               regulator-name = "peri_3p15v_reg";

> +               regulator-min-microvolt = <3150000>;

> +               regulator-max-microvolt = <3150000>;

> +               regulator-always-on;


You can remove the 'regulator-always-on' property as this regulator
will be controlled by AVDD-supply.
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/imx7s-warp.dts b/arch/arm/boot/dts/imx7s-warp.dts
index ffd170ae925a..10df24c05b76 100644
--- a/arch/arm/boot/dts/imx7s-warp.dts
+++ b/arch/arm/boot/dts/imx7s-warp.dts
@@ -91,6 +91,14 @@ 
 		regulator-always-on;
 	};
 
+	reg_peri_3p15v: regulator-peri-3p15v {
+		compatible = "regulator-fixed";
+		regulator-name = "peri_3p15v_reg";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+		regulator-always-on;
+	};
+
 	sound {
 		compatible = "simple-audio-card";
 		simple-audio-card,name = "imx7-sgtl5000";
@@ -218,6 +226,25 @@ 
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
+
+	ov2680: camera@36 {
+		compatible = "ovti,ov2680";
+		reg = <0x36>;
+		clocks = <&osc>;
+		clock-names = "xvclk";
+		reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+		DOVDD-supply = <&sw2_reg>;
+		DVDD-supply = <&sw2_reg>;
+		AVDD-supply = <&reg_peri_3p15v>;
+
+		port {
+			ov2680_to_mipi: endpoint {
+				remote-endpoint = <&mipi_from_sensor>;
+				clock-lanes = <0>;
+				data-lanes = <1>;
+			};
+		};
+	};
 };
 
 &i2c4 {