@@ -5244,6 +5244,13 @@ F: drivers/gpu/drm/msm/
F: include/uapi/drm/msm_drm.h
F: Documentation/devicetree/bindings/display/msm/
+DRM DRIVER FOR NOVATEK NT35510 PANELS
+M: Linus Walleij <linus.walleij@linaro.org>
+T: git git://anongit.freedesktop.org/drm/drm-misc
+S: Maintained
+F: drivers/gpu/drm/panel/panel-novatek-nt35510*
+F: Documentation/devicetree/bindings/display/panel/novatek-nt35510.yaml
+
DRM DRIVER FOR NVIDIA GEFORCE/QUADRO GPUS
M: Ben Skeggs <bskeggs@redhat.com>
L: dri-devel@lists.freedesktop.org
@@ -127,6 +127,17 @@ config DRM_PANEL_NEC_NL8048HL11
panel (found on the Zoom2/3/3630 SDP boards). To compile this driver
as a module, choose M here.
+config DRM_PANEL_NOVATEK_NT35510
+ tristate "Novatek NT35510 RGB panel driver"
+ depends on OF
+ depends on DRM_MIPI_DSI
+ depends on BACKLIGHT_CLASS_DEVICE
+ select VIDEOMODE_HELPERS
+ help
+ Say Y here if you want to enable support for the panels built
+ around the Novatek NT35510 display controller, such as some
+ Hydis panels.
+
config DRM_PANEL_NOVATEK_NT39016
tristate "Novatek NT39016 RGB/SPI panel"
depends on OF && SPI
@@ -11,6 +11,7 @@ obj-$(CONFIG_DRM_PANEL_KINGDISPLAY_KD097D04) += panel-kingdisplay-kd097d04.o
obj-$(CONFIG_DRM_PANEL_LG_LB035Q02) += panel-lg-lb035q02.o
obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o
obj-$(CONFIG_DRM_PANEL_NEC_NL8048HL11) += panel-nec-nl8048hl11.o
+obj-$(CONFIG_DRM_PANEL_NOVATEK_NT35510) += panel-novatek-nt35510.o
obj-$(CONFIG_DRM_PANEL_NOVATEK_NT39016) += panel-novatek-nt39016.o
obj-$(CONFIG_DRM_PANEL_OLIMEX_LCD_OLINUXINO) += panel-olimex-lcd-olinuxino.o
obj-$(CONFIG_DRM_PANEL_ORISETECH_OTM8009A) += panel-orisetech-otm8009a.o
new file mode 100644
@@ -0,0 +1,1126 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Novatek NT35510 panel driver
+ * Copyright (C) 2019 Linus Walleij <linus.walleij@linaro.org>
+ * Based on code by Robert Teather (C) 2012 Samsung
+ *
+ * This display driver (and I refer to the physical component NT35510,
+ * not this Linux kernel software driver) can handle:
+ * 480x864, 480x854, 480x800, 480x720 and 480x640 pixel displays.
+ * It has 480x840x24bit SRAM embedded for storing a frame.
+ * When powered on the display is by default in 480x800 mode.
+ *
+ * The actual panels using this component have different names, but
+ * the code needed to set up and configure the panel will be similar,
+ * so they should all use the NT35510 driver with appropriate configuration
+ * per-panel, e.g. for physical size.
+ *
+ * This driver is for the DSI interface to panels using the NT35510.
+ *
+ * The NT35510 can also use an RGB (DPI) interface combined with an
+ * I2C or SPI interface for setting up the NT35510. If this is needed I
+ * this panel driver should be refactored to also support that use
+ * case.
+ */
+#include <drm/drm_modes.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_print.h>
+
+#include <linux/bitops.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/backlight.h>
+
+#include <video/mipi_display.h>
+#include <video/of_videomode.h>
+#include <video/videomode.h>
+
+#define MCS_CMD_MAUCCTR 0xF0 /* Manufacturer command enable */
+#define MCS_CMD_READ_ID1 0xDA
+#define MCS_CMD_READ_ID2 0xDB
+#define MCS_CMD_READ_ID3 0xDC
+#define MCS_CMD_MTP_READ_SETTING 0xF8 /* Uncertain about name */
+#define MCS_CMD_MTP_READ_PARAM 0xFF /* Uncertain about name */
+
+/*
+ * These manufacturer commands are available after we enable manufacturer
+ * command set (MCS) for page 0.
+ */
+#define NT35510_P0_DOPCTR 0xB1
+#define NT35510_P0_SDHDTCTR 0xB6
+#define NT35510_P0_GSEQCTR 0xB7
+#define NT35510_P0_SDEQCTR 0xB8
+#define NT35510_P0_SDVPCTR 0xBA
+#define NT35510_P0_DPFRCTR1 0xBD
+#define NT35510_P0_DPFRCTR2 0xBE
+#define NT35510_P0_DPFRCTR3 0xBF
+#define NT35510_P0_DPMCTR12 0xCC
+
+#define NT35510_P0_DOPCTR_LEN 2
+#define NT35510_P0_GSEQCTR_LEN 2
+#define NT35510_P0_SDEQCTR_LEN 4
+#define NT35510_P0_SDVPCTR_LEN 1
+#define NT35510_P0_DPFRCTR1_LEN 5
+#define NT35510_P0_DPFRCTR2_LEN 5
+#define NT35510_P0_DPFRCTR3_LEN 5
+#define NT35510_P0_DPMCTR12_LEN 3
+
+#define NT35510_DOPCTR_0_RAMKP BIT(7) /* Contents kept in sleep */
+#define NT35510_DOPCTR_0_DSITE BIT(6) /* Enable TE signal */
+#define NT35510_DOPCTR_0_DSIG BIT(5) /* Enable generic read/write */
+#define NT35510_DOPCTR_0_DSIM BIT(4) /* Enable video mode on DSI */
+#define NT35510_DOPCTR_0_EOTP BIT(3) /* Support EoTP */
+#define NT35510_DOPCTR_0_N565 BIT(2) /* RGB or BGR pixel format */
+#define NT35510_DOPCTR_1_TW_PWR_SEL BIT(4) /* TE power selector */
+#define NT35510_DOPCTR_1_CRGB BIT(3) /* RGB or BGR byte order */
+#define NT35510_DOPCTR_1_CTB BIT(2) /* Vertical scanning direction */
+#define NT35510_DOPCTR_1_CRL BIT(1) /* Source driver data shift */
+#define NT35510_P0_SDVPCTR_PRG BIT(2) /* 0 = normal operation, 1 = VGLO */
+#define NT35510_P0_SDVPCTR_AVDD 0 /* source driver output = AVDD */
+#define NT35510_P0_SDVPCTR_OFFCOL 1 /* source driver output = off color */
+#define NT35510_P0_SDVPCTR_AVSS 2 /* source driver output = AVSS */
+#define NT35510_P0_SDVPCTR_HI_Z 3 /* source driver output = High impedance */
+
+/*
+ * These manufacturer commands are available after we enable manufacturer
+ * command set (MCS) for page 1.
+ */
+#define NT35510_P1_SETAVDD 0xB0
+#define NT35510_P1_SETAVEE 0xB1
+#define NT35510_P1_SETVCL 0xB2
+#define NT35510_P1_SETVGH 0xB3
+#define NT35510_P1_SETVRGH 0xB4
+#define NT35510_P1_SETVGL 0xB5
+#define NT35510_P1_BT1CTR 0xB6
+#define NT35510_P1_BT2CTR 0xB7
+#define NT35510_P1_BT3CTR 0xB8
+#define NT35510_P1_BT4CTR 0xB9 /* VGH boosting times/freq */
+#define NT35510_P1_BT5CTR 0xBA
+#define NT35510_P1_PFMCTR 0xBB
+#define NT35510_P1_SETVGP 0xBC
+#define NT35510_P1_SETVGN 0xBD
+#define NT35510_P1_SETVCMOFF 0xBE
+#define NT35510_P1_VGHCTR 0xBF /* VGH output ctrl */
+#define NT35510_P1_SET_GAMMA_RED_POS 0xD1
+#define NT35510_P1_SET_GAMMA_GREEN_POS 0xD2
+#define NT35510_P1_SET_GAMMA_BLUE_POS 0xD3
+#define NT35510_P1_SET_GAMMA_RED_NEG 0xD4
+#define NT35510_P1_SET_GAMMA_GREEN_NEG 0xD5
+#define NT35510_P1_SET_GAMMA_BLUE_NEG 0xD6
+
+/* AVDD and AVEE setting 3 bytes */
+#define NT35510_P1_AVDD_LEN 3
+#define NT35510_P1_AVEE_LEN 3
+#define NT35510_P1_VGH_LEN 3
+#define NT35510_P1_VGL_LEN 3
+#define NT35510_P1_VGP_LEN 3
+#define NT35510_P1_VGN_LEN 3
+/* BT1CTR thru BT5CTR setting 3 bytes */
+#define NT35510_P1_BT1CTR_LEN 3
+#define NT35510_P1_BT2CTR_LEN 3
+#define NT35510_P1_BT4CTR_LEN 3
+#define NT35510_P1_BT5CTR_LEN 3
+/* 52 gamma parameters times two per color: positive and negative */
+#define NT35510_P1_GAMMA_LEN 52
+
+/**
+ * struct nt35510_config - the display-specific NT35510 configuration
+ *
+ * Some of the settings provide an array of bytes, A, B C which mean:
+ * A = normal / idle off mode
+ * B = idle on mode
+ * C = partial / idle off mode
+ *
+ * Gamma correction arrays are 10bit numbers, two consecutive bytes
+ * makes out one point on the gamma correction curve. The points are
+ * not linearly placed along the X axis, we get points 0, 1, 3, 5
+ * 7, 11, 15, 23, 31, 47, 63, 95, 127, 128, 160, 192, 208, 224, 232,
+ * 240, 244, 248, 250, 252, 254, 255. The voltages tuples form
+ * V0, V1, V3 ... V255, with 0x0000 being the lowest voltage and
+ * 0x03FF being the highest voltage.
+ *
+ * Each value must be strictly lower than the next value forming a
+ * rising curve like this:
+ *
+ * ^
+ * | V255
+ * | V254
+ * | ....
+ * | V5
+ * | V3
+ * | V1
+ * | V0
+ * +------------------------------------------->
+ *
+ * The details about all settings can be found in the NT35510 Application
+ * Note.
+ */
+struct nt35510_config {
+ /**
+ * @width_mm: physical panel width [mm]
+ */
+ u32 width_mm;
+ /**
+ * @height_mm: physical panel height [mm]
+ */
+ u32 height_mm;
+ /**
+ * @mode: the display mode. This is only relevant outside the panel
+ * in video mode: in command mode this is configuring the internal
+ * timing in the display controller.
+ */
+ const struct drm_display_mode mode;
+ /**
+ * @avdd: setting for AVDD ranging from 0x00 = 6.5V to 0x14 = 4.5V
+ * in 0.1V steps the default is 0x05 which means 6.0V
+ */
+ u8 avdd[NT35510_P1_AVDD_LEN];
+ /**
+ * @bt1ctr: setting for boost power control for the AVDD step-up
+ * circuit (1)
+ * bits 0..2 in the lower nybble controls PCK, the booster clock
+ * frequency for the step-up circuit:
+ * 0 = Hsync/32
+ * 1 = Hsync/16
+ * 2 = Hsync/8
+ * 3 = Hsync/4
+ * 4 = Hsync/2
+ * 5 = Hsync
+ * 6 = Hsync x 2
+ * 7 = Hsync x 4
+ * bits 4..6 in the upper nybble controls BTP, the boosting
+ * amplification for the the step-up circuit:
+ * 0 = Disable
+ * 1 = 1.5 x VDDB
+ * 2 = 1.66 x VDDB
+ * 3 = 2 x VDDB
+ * 4 = 2.5 x VDDB
+ * 5 = 3 x VDDB
+ * The defaults are 4 and 4 yielding 0x44
+ */
+ u8 bt1ctr[NT35510_P1_BT1CTR_LEN];
+ /**
+ * @avee: setting for AVEE ranging from 0x00 = -6.5V to 0x14 = -4.5V
+ * in 0.1V steps the default is 0x05 which means -6.0V
+ */
+ u8 avee[NT35510_P1_AVEE_LEN];
+ /**
+ * @bt2ctr: setting for boost power control for the AVEE step-up
+ * circuit (2)
+ * bits 0..2 in the lower nybble controls NCK, the booster clock
+ * frequency, the values are the same as for PCK in @bt1ctr.
+ * bits 4..5 in the upper nybble controls BTN, the boosting
+ * amplification for the the step-up circuit.
+ * 0 = Disable
+ * 1 = -1.5 x VDDB
+ * 2 = -2 x VDDB
+ * 3 = -2.5 x VDDB
+ * 4 = -3 x VDDB
+ * The defaults are 4 and 3 yielding 0x34
+ */
+ u8 bt2ctr[NT35510_P1_BT2CTR_LEN];
+ /**
+ * @vgh: setting for VGH ranging from 0x00 = 7.0V to 0x0B = 18.0V
+ * in 1V steps, the default is 0x08 which means 15V
+ */
+ u8 vgh[NT35510_P1_VGH_LEN];
+ /**
+ * @bt4ctr: setting for boost power control for the VGH step-up
+ * circuit (4)
+ * bits 0..2 in the lower nybble controls HCK, the booster clock
+ * frequency, the values are the same as for PCK in @bt1ctr.
+ * bits 4..5 in the upper nybble controls BTH, the boosting
+ * amplification for the the step-up circuit.
+ * 0 = AVDD + VDDB
+ * 1 = AVDD - AVEE
+ * 2 = AVDD - AVEE + VDDB
+ * 3 = AVDD x 2 - AVEE
+ * The defaults are 4 and 3 yielding 0x34
+ */
+ u8 bt4ctr[NT35510_P1_BT4CTR_LEN];
+ /**
+ * @vgl: setting for VGL ranging from 0x00 = -2V to 0x0f = -15V in
+ * 1V steps, the default is 0x08 which means -10V
+ */
+ u8 vgl[NT35510_P1_VGL_LEN];
+ /**
+ * @bt5ctr: setting for boost power control for the VGL step-up
+ * circuit (5)
+ * bits 0..2 in the lower nybble controls LCK, the booster clock
+ * frequency, the values are the same as for PCK in @bt1ctr.
+ * bits 4..5 in the upper nybble controls BTL, the boosting
+ * amplification for the the step-up circuit.
+ * 0 = AVEE + VCL
+ * 1 = AVEE - AVDD
+ * 2 = AVEE + VCL - AVDD
+ * 3 = AVEE x 2 - AVDD
+ * The defaults are 3 and 2 yielding 0x32
+ */
+ u8 bt5ctr[NT35510_P1_BT5CTR_LEN];
+ /**
+ * @vgp: setting for VGP, the positive gamma divider voltages
+ * VGMP the high voltage and VGSP the low voltage.
+ * The first byte contains bit 8 of VGMP and VGSP in bits 4 and 0
+ * The second byte contains bit 0..7 of VGMP
+ * The third byte contains bit 0..7 of VGSP
+ * VGMP 0x00 = 3.0V .. 0x108 = 6.3V in steps of 12.5mV
+ * VGSP 0x00 = 0V .. 0x111 = 3.7V in steps of 12.5mV
+ */
+ u8 vgp[NT35510_P1_VGP_LEN];
+ /**
+ * @vgn: setting for VGN, the negative gamma divider voltages,
+ * same layout of bytes as @vgp.
+ */
+ u8 vgn[NT35510_P1_VGN_LEN];
+ /**
+ * @sdeqctr: Source driver control settings, first byte is
+ * 0 for mode 1 and 1 for mode 2. Mode 1 uses two steps and
+ * mode 2 uses three steps meaning EQS3 is not used in mode
+ * 1. Mode 2 is default. The last three parameters are EQS1, EQS2
+ * and EQS3, setting the rise time for each equalizer step:
+ * 0x00 = 0.0 us to 0x0f = 7.5 us in steps of 0.5us. The default
+ * is 0x07 = 3.5 us.
+ */
+ u8 sdeqctr[NT35510_P0_SDEQCTR_LEN];
+ /**
+ * @sdvpctr: power/voltage behaviour during vertical porch time
+ */
+ u8 sdvpctr;
+ /**
+ * @t1: the number of pixel clocks on one scanline, range
+ * 0x100 (258 ticks) .. 0x3FF (1024 ticks) so the value + 1
+ * clock ticks.
+ */
+ u16 t1;
+ /**
+ * @vbp: vertical back porch toward the PANEL note: not toward
+ * the DSI host; these are separate interfaces, in from DSI host
+ * and out to the panel.
+ */
+ u8 vbp;
+ /**
+ * @vfp: vertical front porch toward the PANEL.
+ */
+ u8 vfp;
+ /**
+ * @psel: pixel clock divisor: 0 = 1, 1 = 2, 2 = 4, 3 = 8.
+ */
+ u8 psel;
+ /**
+ * @dpmctr12: Display timing control 12
+ * Byte 1 bit 4 selects LVGL voltage level: 0 = VGLX, 1 = VGL_REG
+ * Byte 1 bit 1 selects gate signal mode: 0 = non-overlap, 1 = overlap
+ * Byte 1 bit 0 selects output signal control R/L swap, 0 = normal
+ * 1 = swap all O->E, L->R
+ * Byte 2 is CLW delay clock for CK O/E and CKB O/E signals:
+ * 0x00 = 0us .. 0xFF = 12.75us in 0.05us steps
+ * Byte 3 is FTI_H0 delay time for STP O/E signals:
+ * 0x00 = 0us .. 0xFF = 12.75us in 0.05us steps
+ */
+ u8 dpmctr12[NT35510_P0_DPMCTR12_LEN];
+ /**
+ * @gamma_corr_pos_r: Red gamma correction parameters, positive
+ */
+ u8 gamma_corr_pos_r[NT35510_P1_GAMMA_LEN];
+ /**
+ * @gamma_corr_pos_g: Green gamma correction parameters, positive
+ */
+ u8 gamma_corr_pos_g[NT35510_P1_GAMMA_LEN];
+ /**
+ * @gamma_corr_pos_b: Blue gamma correction parameters, positive
+ */
+ u8 gamma_corr_pos_b[NT35510_P1_GAMMA_LEN];
+ /**
+ * @gamma_corr_neg_r: Red gamma correction parameters, negative
+ */
+ u8 gamma_corr_neg_r[NT35510_P1_GAMMA_LEN];
+ /**
+ * @gamma_corr_neg_g: Green gamma correction parameters, negative
+ */
+ u8 gamma_corr_neg_g[NT35510_P1_GAMMA_LEN];
+ /**
+ * @gamma_corr_neg_b: Blue gamma correction parameters, negative
+ */
+ u8 gamma_corr_neg_b[NT35510_P1_GAMMA_LEN];
+};
+
+/**
+ * struct nt35510 - state container for the NT35510 panel
+ */
+struct nt35510 {
+ /**
+ * @dev: the container device
+ */
+ struct device *dev;
+ /**
+ * @conf: the specific panel configuration, as the NT35510
+ * can be combined with many physical panels, they can have
+ * different physical dimensions and gamma correction etc,
+ * so this is stored in the config.
+ */
+ const struct nt35510_config *conf;
+ /**
+ * @panel: the DRM panel object for the instance
+ */
+ struct drm_panel panel;
+ /**
+ * @bl: backlight device
+ */
+ struct backlight_device *bl;
+ /**
+ * @supplies: regulators supplying the panel
+ */
+ struct regulator_bulk_data supplies[2];
+ /**
+ * @reset_gpio: the reset line
+ */
+ struct gpio_desc *reset_gpio;
+};
+
+/* Manufacturer command has strictly this byte sequence */
+static const u8 nt35510_mauc_select_page_0[] = { 0x55, 0xAA, 0x52, 0x08, 0x00 };
+static const u8 nt35510_mauc_select_page_1[] = { 0x55, 0xAA, 0x52, 0x08, 0x01 };
+static const u8 nt35510_vgh_on[] = { 0x01 };
+
+static inline struct nt35510 *panel_to_nt35510(struct drm_panel *panel)
+{
+ return container_of(panel, struct nt35510, panel);
+}
+
+#define NT35510_ROTATE_0_SETTING 0x02
+#define NT35510_ROTATE_180_SETTING 0x00
+
+static int nt35510_send_long(struct nt35510 *nt, struct mipi_dsi_device *dsi,
+ u8 cmd, u8 cmdlen, const u8 *seq)
+{
+ const u8 *seqp = seq;
+ int cmdwritten = 0;
+ int chunk = cmdlen;
+ int ret;
+
+ if (chunk > 15)
+ chunk = 15;
+ ret = mipi_dsi_dcs_write(dsi, cmd, seqp, chunk);
+ if (ret < 0) {
+ DRM_DEV_ERROR(nt->dev,
+ "error sending DCS command seq cmd %02x\n",
+ cmd);
+ return ret;
+ }
+ cmdwritten += chunk;
+ seqp += chunk;
+
+ while (cmdwritten < cmdlen) {
+ chunk = cmdlen - cmdwritten;
+ if (chunk > 15)
+ chunk = 15;
+ ret = mipi_dsi_generic_write(dsi, seqp, chunk);
+ if (ret < 0) {
+ DRM_DEV_ERROR(nt->dev,
+ "error sending generic write seq %02x\n",
+ cmd);
+ return ret;
+ }
+ cmdwritten += chunk;
+ seqp += chunk;
+ }
+ DRM_DEV_DEBUG(nt->dev, "sent command %02x %02x bytes\n",
+ cmd, cmdlen);
+ return 0;
+}
+
+static int nt35510_read_id(struct nt35510 *nt)
+{
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(nt->dev);
+ u8 id1, id2, id3;
+ int ret;
+
+ ret = mipi_dsi_dcs_read(dsi, MCS_CMD_READ_ID1, &id1, 1);
+ if (ret < 0) {
+ DRM_DEV_ERROR(nt->dev, "could not read MTP ID1\n");
+ return ret;
+ }
+ ret = mipi_dsi_dcs_read(dsi, MCS_CMD_READ_ID2, &id2, 1);
+ if (ret < 0) {
+ DRM_DEV_ERROR(nt->dev, "could not read MTP ID2\n");
+ return ret;
+ }
+ ret = mipi_dsi_dcs_read(dsi, MCS_CMD_READ_ID3, &id3, 1);
+ if (ret < 0) {
+ DRM_DEV_ERROR(nt->dev, "could not read MTP ID3\n");
+ return ret;
+ }
+
+ /*
+ * Multi-Time Programmable (?) memory contains manufacturer
+ * ID (e.g. Hydis 0x55), driver ID (e.g. NT35510 0xc0) and
+ * version.
+ */
+ DRM_DEV_INFO(nt->dev,
+ "MTP ID manufacturer: %02x version: %02x driver: %02x\n",
+ id1, id2, id3);
+
+ return 0;
+}
+
+/**
+ * nt35510_setup_power() - set up power config in page 1
+ * @nt: the display instance to set up
+ */
+static int nt35510_setup_power(struct nt35510 *nt)
+{
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(nt->dev);
+ int ret;
+
+ ret = nt35510_send_long(nt, dsi, NT35510_P1_SETAVDD,
+ NT35510_P1_AVDD_LEN,
+ nt->conf->avdd);
+ if (ret)
+ return ret;
+ ret = nt35510_send_long(nt, dsi, NT35510_P1_BT1CTR,
+ NT35510_P1_BT1CTR_LEN,
+ nt->conf->bt1ctr);
+ if (ret)
+ return ret;
+ ret = nt35510_send_long(nt, dsi, NT35510_P1_SETAVEE,
+ NT35510_P1_AVEE_LEN,
+ nt->conf->avee);
+ if (ret)
+ return ret;
+ ret = nt35510_send_long(nt, dsi, NT35510_P1_BT2CTR,
+ NT35510_P1_BT2CTR_LEN,
+ nt->conf->bt2ctr);
+ if (ret)
+ return ret;
+ ret = nt35510_send_long(nt, dsi, NT35510_P1_SETVGH,
+ NT35510_P1_VGH_LEN,
+ nt->conf->vgh);
+ if (ret)
+ return ret;
+ ret = nt35510_send_long(nt, dsi, NT35510_P1_BT4CTR,
+ NT35510_P1_BT4CTR_LEN,
+ nt->conf->bt4ctr);
+ if (ret)
+ return ret;
+ ret = nt35510_send_long(nt, dsi, NT35510_P1_VGHCTR,
+ ARRAY_SIZE(nt35510_vgh_on),
+ nt35510_vgh_on);
+ if (ret)
+ return ret;
+ ret = nt35510_send_long(nt, dsi, NT35510_P1_SETVGL,
+ NT35510_P1_VGL_LEN,
+ nt->conf->vgl);
+ if (ret)
+ return ret;
+ ret = nt35510_send_long(nt, dsi, NT35510_P1_BT5CTR,
+ NT35510_P1_BT5CTR_LEN,
+ nt->conf->bt5ctr);
+ if (ret)
+ return ret;
+ ret = nt35510_send_long(nt, dsi, NT35510_P1_SETVGP,
+ NT35510_P1_VGP_LEN,
+ nt->conf->vgp);
+ if (ret)
+ return ret;
+ ret = nt35510_send_long(nt, dsi, NT35510_P1_SETVGN,
+ NT35510_P1_VGN_LEN,
+ nt->conf->vgn);
+ if (ret)
+ return ret;
+
+ /* Typically 10 ms */
+ usleep_range(10000, 20000);
+
+ return 0;
+}
+
+/**
+ * nt35510_setup_display() - set up display config in page 0
+ * @nt: the display instance to set up
+ */
+static int nt35510_setup_display(struct nt35510 *nt)
+{
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(nt->dev);
+ const struct nt35510_config *conf = nt->conf;
+ u8 dopctr[NT35510_P0_DOPCTR_LEN];
+ u8 gseqctr[NT35510_P0_GSEQCTR_LEN];
+ u8 dpfrctr[NT35510_P0_DPFRCTR1_LEN];
+ /* FIXME: set up any rotation (assume none for now) */
+ u8 addr_mode = NT35510_ROTATE_0_SETTING;
+ u8 val;
+ int ret;
+
+ /* Enable TE, EoTP and RGB pixel format */
+ dopctr[0] = NT35510_DOPCTR_0_DSITE | NT35510_DOPCTR_0_EOTP |
+ NT35510_DOPCTR_0_N565;
+ dopctr[1] = NT35510_DOPCTR_1_CTB;
+ ret = nt35510_send_long(nt, dsi, NT35510_P0_DOPCTR,
+ NT35510_P0_DOPCTR_LEN,
+ dopctr);
+ if (ret)
+ return ret;
+
+ ret = mipi_dsi_dcs_write(dsi, MIPI_DCS_SET_ADDRESS_MODE, &addr_mode,
+ sizeof(addr_mode));
+ if (ret < 0)
+ return ret;
+
+ /*
+ * Source data hold time, default 0x05 = 2.5us
+ * 0x00..0x3F = 0 .. 31.5us in steps of 0.5us
+ * 0x0A = 5us
+ */
+ val = 0x0A;
+ ret = mipi_dsi_dcs_write(dsi, NT35510_P0_SDHDTCTR, &val,
+ sizeof(val));
+ if (ret < 0)
+ return ret;
+
+ /* EQ control for gate signals, 0x00 = 0 us */
+ gseqctr[0] = 0x00;
+ gseqctr[1] = 0x00;
+ ret = nt35510_send_long(nt, dsi, NT35510_P0_GSEQCTR,
+ NT35510_P0_GSEQCTR_LEN,
+ gseqctr);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(nt, dsi, NT35510_P0_SDEQCTR,
+ NT35510_P0_SDEQCTR_LEN,
+ conf->sdeqctr);
+ if (ret)
+ return ret;
+
+ ret = mipi_dsi_dcs_write(dsi, NT35510_P0_SDVPCTR,
+ &conf->sdvpctr, 1);
+ if (ret < 0)
+ return ret;
+
+ /*
+ * Display timing control for active and idle off mode:
+ * the first byte contains
+ * the two high bits of T1A and second byte the low 8 bits, and
+ * the valid range is 0x100 (257) to 0x3ff (1023) representing
+ * 258..1024 (+1) pixel clock ticks for one scanline. At 20MHz pixel
+ * clock this covers the range of 12.90us .. 51.20us in steps of
+ * 0.05us, the default is 0x184 (388) representing 389 ticks.
+ * The third byte is VBPDA, vertical back porch display active
+ * and the fourth VFPDA, vertical front porch display active,
+ * both given in number of scanlines in the range 0x02..0xff
+ * for 2..255 scanlines. The fifth byte is 2 bits selecting
+ * PSEL for active and idle off mode, how much the 20MHz clock
+ * is divided by 0..3. This needs to be adjusted to get the right
+ * frame rate.
+ */
+ dpfrctr[0] = (conf->t1 >> 8) & 0xFF;
+ dpfrctr[1] = conf->t1 & 0xFF;
+ /* Vertical back porch */
+ dpfrctr[2] = conf->vbp;
+ /* Vertical front porch */
+ dpfrctr[3] = conf->vfp;
+ dpfrctr[4] = conf->psel;
+ ret = nt35510_send_long(nt, dsi, NT35510_P0_DPFRCTR1,
+ NT35510_P0_DPFRCTR1_LEN,
+ dpfrctr);
+ if (ret)
+ return ret;
+ /* For idle and partial idle off mode we decrease front porch by one */
+ dpfrctr[3]--;
+ ret = nt35510_send_long(nt, dsi, NT35510_P0_DPFRCTR2,
+ NT35510_P0_DPFRCTR2_LEN,
+ dpfrctr);
+ if (ret)
+ return ret;
+ ret = nt35510_send_long(nt, dsi, NT35510_P0_DPFRCTR3,
+ NT35510_P0_DPFRCTR3_LEN,
+ dpfrctr);
+ if (ret)
+ return ret;
+
+ /* Enable TE on vblank */
+ ret = mipi_dsi_dcs_set_tear_on(dsi, MIPI_DSI_DCS_TEAR_MODE_VBLANK);
+ if (ret)
+ return ret;
+
+ /* Turn on the pads? */
+ ret = nt35510_send_long(nt, dsi, NT35510_P0_DPMCTR12,
+ NT35510_P0_DPMCTR12_LEN,
+ conf->dpmctr12);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int nt35510_set_brightness(struct backlight_device *bl)
+{
+ struct nt35510 *nt = bl_get_data(bl);
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(nt->dev);
+ u8 brightness = bl->props.brightness;
+ int ret;
+
+ DRM_DEV_DEBUG(nt->dev, "set brightness %d\n", brightness);
+ ret = mipi_dsi_dcs_write(dsi, MIPI_DCS_SET_DISPLAY_BRIGHTNESS,
+ &brightness,
+ sizeof(brightness));
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+static const struct backlight_ops nt35510_bl_ops = {
+ .update_status = nt35510_set_brightness,
+};
+
+/*
+ * This power-on sequence
+ */
+static int nt35510_power_on(struct nt35510 *nt)
+{
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(nt->dev);
+ int ret;
+
+ ret = regulator_bulk_enable(ARRAY_SIZE(nt->supplies), nt->supplies);
+ if (ret < 0) {
+ dev_err(nt->dev, "unable to enable regulators\n");
+ return ret;
+ }
+
+ /* Toggle RESET in accordance with datasheet page 370 */
+ if (nt->reset_gpio) {
+ gpiod_set_value(nt->reset_gpio, 1);
+ /* Active min 10 us according to datasheet, let's say 20 */
+ usleep_range(20, 1000);
+ gpiod_set_value(nt->reset_gpio, 0);
+ /*
+ * 5 ms during sleep mode, 120 ms during sleep out mode
+ * according to datasheet, let's use 120-140 ms.
+ */
+ usleep_range(120000, 140000);
+ }
+
+ ret = nt35510_read_id(nt);
+ if (ret)
+ return ret;
+
+ /* Set up stuff in manufacturer control, page 1 */
+ ret = nt35510_send_long(nt, dsi, MCS_CMD_MAUCCTR,
+ ARRAY_SIZE(nt35510_mauc_select_page_1),
+ nt35510_mauc_select_page_1);
+ if (ret)
+ return ret;
+
+ ret = nt35510_setup_power(nt);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(nt, dsi, NT35510_P1_SET_GAMMA_RED_POS,
+ NT35510_P1_GAMMA_LEN,
+ nt->conf->gamma_corr_pos_r);
+ if (ret)
+ return ret;
+ ret = nt35510_send_long(nt, dsi, NT35510_P1_SET_GAMMA_GREEN_POS,
+ NT35510_P1_GAMMA_LEN,
+ nt->conf->gamma_corr_pos_g);
+ if (ret)
+ return ret;
+ ret = nt35510_send_long(nt, dsi, NT35510_P1_SET_GAMMA_BLUE_POS,
+ NT35510_P1_GAMMA_LEN,
+ nt->conf->gamma_corr_pos_b);
+ if (ret)
+ return ret;
+ ret = nt35510_send_long(nt, dsi, NT35510_P1_SET_GAMMA_RED_NEG,
+ NT35510_P1_GAMMA_LEN,
+ nt->conf->gamma_corr_neg_r);
+ if (ret)
+ return ret;
+ ret = nt35510_send_long(nt, dsi, NT35510_P1_SET_GAMMA_GREEN_NEG,
+ NT35510_P1_GAMMA_LEN,
+ nt->conf->gamma_corr_neg_g);
+ if (ret)
+ return ret;
+ ret = nt35510_send_long(nt, dsi, NT35510_P1_SET_GAMMA_BLUE_NEG,
+ NT35510_P1_GAMMA_LEN,
+ nt->conf->gamma_corr_neg_b);
+ if (ret)
+ return ret;
+
+ /* Set up stuff in manufacturer control, page 0 */
+ ret = nt35510_send_long(nt, dsi, MCS_CMD_MAUCCTR,
+ ARRAY_SIZE(nt35510_mauc_select_page_0),
+ nt35510_mauc_select_page_0);
+ if (ret)
+ return ret;
+
+ ret = nt35510_setup_display(nt);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int nt35510_power_off(struct nt35510 *nt)
+{
+ int ret;
+
+ ret = regulator_bulk_disable(ARRAY_SIZE(nt->supplies), nt->supplies);
+ if (ret)
+ return ret;
+
+ if (nt->reset_gpio)
+ gpiod_set_value(nt->reset_gpio, 1);
+
+ return 0;
+}
+
+static int nt35510_disable(struct drm_panel *panel)
+{
+ struct nt35510 *nt = panel_to_nt35510(panel);
+
+ dev_info(nt->dev, "disable\n");
+ backlight_disable(nt->bl);
+ return 0;
+}
+
+static int nt35510_unprepare(struct drm_panel *panel)
+{
+ struct nt35510 *nt = panel_to_nt35510(panel);
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(nt->dev);
+ int ret;
+
+ dev_info(nt->dev, "unprepare\n");
+
+ ret = mipi_dsi_dcs_set_display_off(dsi);
+ if (ret) {
+ DRM_DEV_ERROR(nt->dev, "failed to turn display off (%d)\n",
+ ret);
+ return ret;
+ }
+ usleep_range(10000, 20000);
+
+ /* Enter sleep mode */
+ ret = mipi_dsi_dcs_enter_sleep_mode(dsi);
+ if (ret) {
+ DRM_DEV_ERROR(nt->dev, "failed to enter sleep mode (%d)\n",
+ ret);
+ return ret;
+ }
+
+ /* Wait 4 frames, how much is that 5ms in the vendor driver */
+ usleep_range(5000, 10000);
+
+ ret = nt35510_power_off(nt);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int nt35510_prepare(struct drm_panel *panel)
+{
+ struct nt35510 *nt = panel_to_nt35510(panel);
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(nt->dev);
+ int ret;
+
+ dev_info(nt->dev, "prepare\n");
+
+ ret = nt35510_power_on(nt);
+ if (ret)
+ return ret;
+
+ /* Exit sleep mode */
+ ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
+ if (ret) {
+ DRM_DEV_ERROR(nt->dev, "failed to exit sleep mode (%d)\n",
+ ret);
+ return ret;
+ }
+ /* Up to 120 ms */
+ usleep_range(120000, 150000);
+
+ ret = mipi_dsi_dcs_set_display_on(dsi);
+ if (ret) {
+ DRM_DEV_ERROR(nt->dev, "failed to turn display on (%d)\n",
+ ret);
+ return ret;
+ }
+ /* Some 10 ms */
+ usleep_range(10000, 20000);
+
+ return 0;
+}
+
+static int nt35510_enable(struct drm_panel *panel)
+{
+ struct nt35510 *nt = panel_to_nt35510(panel);
+
+ dev_info(nt->dev, "enable\n");
+ backlight_enable(nt->bl);
+
+ return 0;
+}
+
+static int nt35510_get_modes(struct drm_panel *panel)
+{
+ struct drm_connector *connector = panel->connector;
+ struct nt35510 *nt = panel_to_nt35510(panel);
+ struct drm_display_mode *mode;
+ struct drm_display_info *info;
+
+ info = &connector->display_info;
+ info->width_mm = nt->conf->width_mm;
+ info->height_mm = nt->conf->height_mm;
+ mode = drm_mode_duplicate(panel->drm, &nt->conf->mode);
+ if (!mode) {
+ DRM_ERROR("bad mode or failed to add mode\n");
+ return -EINVAL;
+ }
+ drm_mode_set_name(mode);
+ mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+
+ mode->width_mm = nt->conf->width_mm;
+ mode->height_mm = nt->conf->height_mm;
+ drm_mode_probed_add(connector, mode);
+
+ return 1; /* Number of modes */
+}
+
+static const struct drm_panel_funcs nt35510_drm_funcs = {
+ .disable = nt35510_disable,
+ .unprepare = nt35510_unprepare,
+ .prepare = nt35510_prepare,
+ .enable = nt35510_enable,
+ .get_modes = nt35510_get_modes,
+};
+
+static int nt35510_probe(struct mipi_dsi_device *dsi)
+{
+ struct device *dev = &dsi->dev;
+ struct nt35510 *nt;
+ int ret;
+
+ nt = devm_kzalloc(dev, sizeof(struct nt35510), GFP_KERNEL);
+ if (!nt)
+ return -ENOMEM;
+ mipi_dsi_set_drvdata(dsi, nt);
+ nt->dev = dev;
+
+ dsi->lanes = 2;
+ dsi->format = MIPI_DSI_FMT_RGB888;
+ /*
+ * Datasheet suggests max HS rate for NT35510 is 250 MHz
+ * (period time 4ns, see figure 7.6.4 page 365) and max LP rate is
+ * 20 MHz (period time 50ns, see figure 7.6.6. page 366).
+ * However these frequencies appear in source code for the Hydis
+ * HVA40WV1 panel and setting up the LP frequency makes the panel
+ * not work.
+ *
+ * TODO: if other panels prove to be closer to the datasheet,
+ * maybe make this a per-panel config in struct nt35510_config?
+ */
+ dsi->hs_rate = 349440000;
+ dsi->lp_rate = 9600000;
+ dsi->mode_flags = MIPI_DSI_CLOCK_NON_CONTINUOUS |
+ MIPI_DSI_MODE_EOT_PACKET;
+
+ /*
+ * Every new incarnation of this display must have a unique
+ * data entry for the system in this driver.
+ */
+ nt->conf = of_device_get_match_data(dev);
+ if (!nt->conf) {
+ dev_err(dev, "missing device configuration\n");
+ return -ENODEV;
+ }
+
+ nt->supplies[0].supply = "vdd"; /* 2.3-4.8 V */
+ nt->supplies[1].supply = "vddi"; /* 1.65-3.3V */
+ ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(nt->supplies),
+ nt->supplies);
+ if (ret < 0)
+ return ret;
+ ret = regulator_set_voltage(nt->supplies[0].consumer,
+ 2300000, 4800000);
+ if (ret)
+ return ret;
+ ret = regulator_set_voltage(nt->supplies[1].consumer,
+ 1650000, 3300000);
+ if (ret)
+ return ret;
+
+ nt->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_ASIS);
+ if (IS_ERR(nt->reset_gpio)) {
+ dev_err(dev, "error getting RESET GPIO\n");
+ return PTR_ERR(nt->reset_gpio);
+ }
+
+ drm_panel_init(&nt->panel, dev, &nt35510_drm_funcs,
+ DRM_MODE_CONNECTOR_DSI);
+
+ /*
+ * First, try to locate an external backlight (such as on GPIO)
+ * if this fails, assume we will want to use the internal backlight
+ * control.
+ */
+ nt->bl = devm_of_find_backlight(dev);
+ if (IS_ERR(nt->bl)) {
+ dev_err(dev, "error getting external backlight %d\n", ret);
+ return PTR_ERR(nt->bl);
+ }
+ if (!nt->bl) {
+ nt->bl = devm_backlight_device_register(dev, "nt35510", dev, nt,
+ &nt35510_bl_ops, NULL);
+ if (IS_ERR(nt->bl)) {
+ DRM_DEV_ERROR(dev, "failed to register backlight device\n");
+ return PTR_ERR(nt->bl);
+ }
+ nt->bl->props.max_brightness = 255;
+ nt->bl->props.brightness = 255;
+ nt->bl->props.power = FB_BLANK_POWERDOWN;
+ }
+
+ ret = drm_panel_add(&nt->panel);
+ if (ret < 0)
+ return ret;
+
+ ret = mipi_dsi_attach(dsi);
+ if (ret < 0)
+ drm_panel_remove(&nt->panel);
+
+ return 0;
+}
+
+static int nt35510_remove(struct mipi_dsi_device *dsi)
+{
+ struct nt35510 *nt = mipi_dsi_get_drvdata(dsi);
+ int ret;
+
+ mipi_dsi_detach(dsi);
+ /* Power off */
+ ret = nt35510_power_off(nt);
+ drm_panel_remove(&nt->panel);
+
+ return ret;
+}
+
+/*
+ * These gamma correction values are 10bit tuples, so only bits 0 and 1 is
+ * ever used in the first byte. They form a positive and negative gamma
+ * correction curve for each color, values must be strictly higher for each
+ * step on the curve. As can be seen these default curves goes from 0x0001
+ * to 0x03FE.
+ */
+#define NT35510_GAMMA_POS_DEFAULT 0x00, 0x01, 0x00, 0x43, 0x00, \
+ 0x6B, 0x00, 0x87, 0x00, 0xA3, 0x00, 0xCE, 0x00, 0xF1, 0x01, \
+ 0x27, 0x01, 0x53, 0x01, 0x98, 0x01, 0xCE, 0x02, 0x22, 0x02, \
+ 0x83, 0x02, 0x78, 0x02, 0x9E, 0x02, 0xDD, 0x03, 0x00, 0x03, \
+ 0x2E, 0x03, 0x54, 0x03, 0x7F, 0x03, 0x95, 0x03, 0xB3, 0x03, \
+ 0xC2, 0x03, 0xE1, 0x03, 0xF1, 0x03, 0xFE
+
+#define NT35510_GAMMA_NEG_DEFAULT 0x00, 0x01, 0x00, 0x43, 0x00, \
+ 0x6B, 0x00, 0x87, 0x00, 0xA3, 0x00, 0xCE, 0x00, 0xF1, 0x01, \
+ 0x27, 0x01, 0x53, 0x01, 0x98, 0x01, 0xCE, 0x02, 0x22, 0x02, \
+ 0x43, 0x02, 0x50, 0x02, 0x9E, 0x02, 0xDD, 0x03, 0x00, 0x03, \
+ 0x2E, 0x03, 0x54, 0x03, 0x7F, 0x03, 0x95, 0x03, 0xB3, 0x03, \
+ 0xC2, 0x03, 0xE1, 0x03, 0xF1, 0x03, 0xFE
+
+/*
+ * The Hydis HVA40WV1 panel
+ */
+static const struct nt35510_config nt35510_hydis_hva40wv1 = {
+ .width_mm = 52,
+ .height_mm = 86,
+ /**
+ * As the Hydis panel is used in command mode, the porches etc
+ * are settings programmed internally into the NT35510 controller
+ * and generated toward the physical display. As the panel is not
+ * used in video mode, these are not really exposed to the DSI
+ * host.
+ *
+ * Display frame rate control:
+ * Frame rate = (20 MHz / 1) / (389 * (7 + 50 + 800)) ~= 60 Hz
+ */
+ .mode = {
+ /* The internal pixel clock of the NT35510 is 20 MHz */
+ .clock = 20000000,
+ .hdisplay = 480,
+ .hsync_start = 480 + 2, /* HFP = 2 */
+ .hsync_end = 480 + 2 + 0, /* HSync = 0 */
+ .htotal = 480 + 2 + 0 + 5, /* HFP = 5 */
+ .vdisplay = 800,
+ .vsync_start = 800 + 2, /* VFP = 2 */
+ .vsync_end = 800 + 2 + 0, /* VSync = 0 */
+ .vtotal = 800 + 2 + 0 + 5, /* VBP = 5 */
+ .vrefresh = 60, /* Calculated */
+ .flags = 0,
+ },
+ /* 0x09: AVDD = 5.6V */
+ .avdd = { 0x09, 0x09, 0x09 },
+ /* 0x34: PCK = Hsync/2, BTP = 2 x VDDB */
+ .bt1ctr = { 0x34, 0x34, 0x34 },
+ /* 0x09: AVEE = -5.6V */
+ .avee = { 0x09, 0x09, 0x09 },
+ /* 0x24: NCK = Hsync/2, BTN = -2 x VDDB */
+ .bt2ctr = { 0x24, 0x24, 0x24 },
+ /* 0x05 = 12V */
+ .vgh = { 0x05, 0x05, 0x05 },
+ /* 0x24: NCKA = Hsync/2, VGH = 2 x AVDD - AVEE */
+ .bt4ctr = { 0x24, 0x24, 0x24 },
+ /* 0x0B = -13V */
+ .vgl = { 0x0B, 0x0B, 0x0B },
+ /* 0x24: LCKA = Hsync, VGL = AVDD + VCL - AVDD */
+ .bt5ctr = { 0x24, 0x24, 0x24 },
+ /* VGMP: 0x0A3 = 5.0375V, VGSP = 0V */
+ .vgp = { 0x00, 0xA3, 0x00 },
+ /* VGMP: 0x0A3 = 5.0375V, VGSP = 0V */
+ .vgn = { 0x00, 0xA3, 0x00 },
+ /* SDEQCTR: source driver EQ mode 2, 2.5 us rise time on each step */
+ .sdeqctr = { 0x01, 0x05, 0x05, 0x05 },
+ /* SDVPCTR: Normal operation off color during v porch */
+ .sdvpctr = 0x01,
+ /* T1: number of pixel clocks on one scanline: 0x184 = 389 clocks */
+ .t1 = 0x0184,
+ /* VBP: vertical back porch toward the panel */
+ .vbp = 7,
+ /* VFP: vertical front porch toward the panel */
+ .vfp = 50,
+ /* PSEL: divide pixel clock 20MHz with 1 (no clock downscaling) */
+ .psel = 0,
+ /* DPTMCTR12: 0x03: LVGL = VGLX, overlap mode, swap R->L O->E */
+ .dpmctr12 = { 0x03, 0x00, 0x00, },
+ /* Default gamma correction values */
+ .gamma_corr_pos_r = { NT35510_GAMMA_POS_DEFAULT },
+ .gamma_corr_pos_g = { NT35510_GAMMA_POS_DEFAULT },
+ .gamma_corr_pos_b = { NT35510_GAMMA_POS_DEFAULT },
+ .gamma_corr_neg_r = { NT35510_GAMMA_NEG_DEFAULT },
+ .gamma_corr_neg_g = { NT35510_GAMMA_NEG_DEFAULT },
+ .gamma_corr_neg_b = { NT35510_GAMMA_NEG_DEFAULT },
+};
+
+static const struct of_device_id nt35510_of_match[] = {
+ {
+ .compatible = "hydis,hva40wv1",
+ .data = &nt35510_hydis_hva40wv1,
+ },
+ { }
+};
+MODULE_DEVICE_TABLE(of, nt35510_of_match);
+
+static struct mipi_dsi_driver nt35510_driver = {
+ .probe = nt35510_probe,
+ .remove = nt35510_remove,
+ .driver = {
+ .name = "panel-novatek-nt35510",
+ .of_match_table = nt35510_of_match,
+ },
+};
+module_mipi_dsi_driver(nt35510_driver);
+
+MODULE_AUTHOR("Linus Walleij <linus.walleij@linaro.org>");
+MODULE_DESCRIPTION("NT35510-based panel driver");
+MODULE_LICENSE("GPL v2");
This adds a driver for panels based on the Novatek NT35510 display driver IC, such as the Hydis HVA40WV1 panel found in the Samsung GT-S7710. The NT35510 can be used with both internal and external backlight (such as GPIO backlight) so we support both: if no external backlight is found, we register a subdriver for the internal backlight. Cc: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- MAINTAINERS | 7 + drivers/gpu/drm/panel/Kconfig | 11 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-novatek-nt35510.c | 1126 +++++++++++++++++ 4 files changed, 1145 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-novatek-nt35510.c -- 2.21.0 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel