@@ -22,10 +22,19 @@ include $(TOPDIR)/config.mk
LIB = $(obj)lib$(SOC).o
-COBJS += clock.o power.o soc.o system.o pinmux.o tzpc.o
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS))
+COBJS-y += clock.o power.o soc.o system.o pinmux.o tzpc.o
+
+ifdef CONFIG_SPL_BUILD
+COBJS-$(CONFIG_EXYNOS5) += clock_init_exynos5.o
+COBJS-$(CONFIG_EXYNOS5) += dmc_common.o dmc_init_ddr3.o
+COBJS-$(CONFIG_EXYNOS4210)+= dmc_init_exynos4.o clock_init_exynos4.o
+COBJS-y += spl_boot.o
+COBJS-y += lowlevel_init.o
+endif
+
+COBJS := $(COBJS-y)
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
all: $(obj).depend $(LIB)
similarity index 100%
rename from board/samsung/smdk5250/clock_init.h
rename to arch/arm/cpu/armv7/exynos/clock_init.h
new file mode 100644
@@ -0,0 +1,95 @@
+/*
+ * Clock Initialization for board based on EXYNOS4210
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ * Rajeshwari Shinde <rajeshwari.s@samsung.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <config.h>
+#include <version.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/clock.h>
+#include "common_setup.h"
+#include "exynos4_setup.h"
+
+/*
+ * system_clock_init: Initialize core clock and bus clock.
+ * void system_clock_init(void)
+ */
+void system_clock_init(void)
+{
+ struct exynos4_clock *clk =
+ (struct exynos4_clock *)samsung_get_base_clock();
+
+ writel(CLK_SRC_CPU_VAL, &clk->src_cpu);
+
+ sdelay(0x10000);
+
+ writel(CLK_SRC_TOP0_VAL, &clk->src_top0);
+ writel(CLK_SRC_TOP1_VAL, &clk->src_top1);
+ writel(CLK_SRC_DMC_VAL, &clk->src_dmc);
+ writel(CLK_SRC_LEFTBUS_VAL, &clk->src_leftbus);
+ writel(CLK_SRC_RIGHTBUS_VAL, &clk->src_rightbus);
+ writel(CLK_SRC_FSYS_VAL, &clk->src_fsys);
+ writel(CLK_SRC_PERIL0_VAL, &clk->src_peril0);
+ writel(CLK_SRC_CAM_VAL, &clk->src_cam);
+ writel(CLK_SRC_MFC_VAL, &clk->src_mfc);
+ writel(CLK_SRC_G3D_VAL, &clk->src_g3d);
+ writel(CLK_SRC_LCD0_VAL, &clk->src_lcd0);
+
+ sdelay(0x10000);
+
+ writel(CLK_DIV_CPU0_VAL, &clk->div_cpu0);
+ writel(CLK_DIV_CPU1_VAL, &clk->div_cpu1);
+ writel(CLK_DIV_DMC0_VAL, &clk->div_dmc0);
+ writel(CLK_DIV_DMC1_VAL, &clk->div_dmc1);
+ writel(CLK_DIV_LEFTBUS_VAL, &clk->div_leftbus);
+ writel(CLK_DIV_RIGHTBUS_VAL, &clk->div_rightbus);
+ writel(CLK_DIV_TOP_VAL, &clk->div_top);
+ writel(CLK_DIV_FSYS1_VAL, &clk->div_fsys1);
+ writel(CLK_DIV_FSYS2_VAL, &clk->div_fsys2);
+ writel(CLK_DIV_FSYS3_VAL, &clk->div_fsys3);
+ writel(CLK_DIV_PERIL0_VAL, &clk->div_peril0);
+ writel(CLK_DIV_CAM_VAL, &clk->div_cam);
+ writel(CLK_DIV_MFC_VAL, &clk->div_mfc);
+ writel(CLK_DIV_G3D_VAL, &clk->div_g3d);
+ writel(CLK_DIV_LCD0_VAL, &clk->div_lcd0);
+
+ /* Set PLL locktime */
+ writel(PLL_LOCKTIME, &clk->apll_lock);
+ writel(PLL_LOCKTIME, &clk->mpll_lock);
+ writel(PLL_LOCKTIME, &clk->epll_lock);
+ writel(PLL_LOCKTIME, &clk->vpll_lock);
+
+ writel(APLL_CON1_VAL, &clk->apll_con1);
+ writel(APLL_CON0_VAL, &clk->apll_con0);
+ writel(MPLL_CON1_VAL, &clk->mpll_con1);
+ writel(MPLL_CON0_VAL, &clk->mpll_con0);
+ writel(EPLL_CON1_VAL, &clk->epll_con1);
+ writel(EPLL_CON0_VAL, &clk->epll_con0);
+ writel(VPLL_CON1_VAL, &clk->vpll_con1);
+ writel(VPLL_CON0_VAL, &clk->vpll_con0);
+
+ sdelay(0x30000);
+}
similarity index 94%
rename from board/samsung/smdk5250/clock_init.c
rename to arch/arm/cpu/armv7/exynos/clock_init_exynos5.c
@@ -31,7 +31,8 @@
#include <asm/arch/dwmmc.h>
#include "clock_init.h"
-#include "setup.h"
+#include "common_setup.h"
+#include "exynos5_setup.h"
#define FSYS1_MMC0_DIV_MASK 0xff0f
#define FSYS1_MMC0_DIV_VAL 0x0701
@@ -214,10 +215,10 @@ struct mem_timings mem_timings[] = {
DMC_MEMCONTROL_BL_8 |
DMC_MEMCONTROL_PZQ_DISABLE |
DMC_MEMCONTROL_MRR_BYTE_7_0,
- .memconfig = DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED |
- DMC_MEMCONFIGx_CHIP_COL_10 |
- DMC_MEMCONFIGx_CHIP_ROW_15 |
- DMC_MEMCONFIGx_CHIP_BANK_8,
+ .memconfig = DMC_MEMCONFIGX_CHIP_MAP_INTERLEAVED |
+ DMC_MEMCONFIGX_CHIP_COL_10 |
+ DMC_MEMCONFIGX_CHIP_ROW_15 |
+ DMC_MEMCONFIGX_CHIP_BANK_8,
.membaseconfig0 = DMC_MEMBASECONFIG_VAL(0x40),
.membaseconfig1 = DMC_MEMBASECONFIG_VAL(0x80),
.prechconfig_tp_cnt = 0xff,
@@ -317,10 +318,10 @@ struct mem_timings mem_timings[] = {
DMC_MEMCONTROL_BL_8 |
DMC_MEMCONTROL_PZQ_DISABLE |
DMC_MEMCONTROL_MRR_BYTE_7_0,
- .memconfig = DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED |
- DMC_MEMCONFIGx_CHIP_COL_10 |
- DMC_MEMCONFIGx_CHIP_ROW_15 |
- DMC_MEMCONFIGx_CHIP_BANK_8,
+ .memconfig = DMC_MEMCONFIGX_CHIP_MAP_INTERLEAVED |
+ DMC_MEMCONFIGX_CHIP_COL_10 |
+ DMC_MEMCONFIGX_CHIP_ROW_15 |
+ DMC_MEMCONFIGX_CHIP_BANK_8,
.membaseconfig0 = DMC_MEMBASECONFIG_VAL(0x40),
.membaseconfig1 = DMC_MEMBASECONFIG_VAL(0x80),
.prechconfig_tp_cnt = 0xff,
@@ -350,9 +351,8 @@ struct mem_timings mem_timings[] = {
* @param frequency_mhz Returns memory speed in MHz
* @param arm_freq Returns ARM clock speed in MHz
* @param mem_manuf Return Memory Manufacturer name
- * @return 0 if all ok
*/
-static int clock_get_mem_selection(enum ddr_mode *mem_type,
+static void clock_get_mem_selection(enum ddr_mode *mem_type,
unsigned *frequency_mhz, unsigned *arm_freq,
enum mem_manuf *mem_manuf)
{
@@ -363,8 +363,6 @@ static int clock_get_mem_selection(enum ddr_mode *mem_type,
*frequency_mhz = params->frequency_mhz;
*arm_freq = params->arm_freq_mhz;
*mem_manuf = params->mem_manuf;
-
- return 0;
}
/* Get the ratios for setting ARM clock */
@@ -376,9 +374,9 @@ struct arm_clk_ratios *get_arm_ratios(void)
unsigned frequency_mhz, arm_freq;
int i;
- if (clock_get_mem_selection(&mem_type, &frequency_mhz,
- &arm_freq, &mem_manuf))
- ;
+ clock_get_mem_selection(&mem_type, &frequency_mhz,
+ &arm_freq, &mem_manuf);
+
for (i = 0, arm_ratio = arm_clk_ratios; i < ARRAY_SIZE(arm_clk_ratios);
i++, arm_ratio++) {
if (arm_ratio->arm_freq_mhz == arm_freq)
@@ -400,15 +398,14 @@ struct mem_timings *clock_get_mem_timings(void)
unsigned frequency_mhz, arm_freq;
int i;
- if (!clock_get_mem_selection(&mem_type, &frequency_mhz,
- &arm_freq, &mem_manuf)) {
- for (i = 0, mem = mem_timings; i < ARRAY_SIZE(mem_timings);
- i++, mem++) {
- if (mem->mem_type == mem_type &&
- mem->frequency_mhz == frequency_mhz &&
- mem->mem_manuf == mem_manuf)
- return mem;
- }
+ clock_get_mem_selection(&mem_type, &frequency_mhz,
+ &arm_freq, &mem_manuf);
+ for (i = 0, mem = mem_timings; i < ARRAY_SIZE(mem_timings);
+ i++, mem++) {
+ if (mem->mem_type == mem_type &&
+ mem->frequency_mhz == frequency_mhz &&
+ mem->mem_manuf == mem_manuf)
+ return mem;
}
/* will hang if failed to find memory timings */
@@ -420,7 +417,8 @@ struct mem_timings *clock_get_mem_timings(void)
void system_clock_init()
{
- struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE;
+ struct exynos5_clock *clk =
+ (struct exynos5_clock *)samsung_get_base_clock();
struct mem_timings *mem;
struct arm_clk_ratios *arm_clk_ratio;
u32 val, tmp;
@@ -660,7 +658,8 @@ void system_clock_init()
void clock_init_dp_clock(void)
{
- struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE;
+ struct exynos5_clock *clk =
+ (struct exynos5_clock *)samsung_get_base_clock();
/* DP clock enable */
setbits_le32(&clk->gate_ip_disp1, CLK_GATE_DP1_ALLOW);
@@ -675,7 +674,8 @@ void clock_init_dp_clock(void)
*/
void emmc_boot_clk_div_set(void)
{
- struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE;
+ struct exynos5_clock *clk =
+ (struct exynos5_clock *)samsung_get_base_clock();
unsigned int div_mmc;
div_mmc = readl((unsigned int) &clk->div_fsys1) & ~FSYS1_MMC0_DIV_MASK;
new file mode 100644
@@ -0,0 +1,45 @@
+/*
+ * Common APIs for EXYNOS based board
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ * Rajeshwari Shinde <rajeshwari.s@samsung.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#define DMC_OFFSET 0x10000
+
+/*
+ * Memory initialization
+ *
+ * @param reset Reset PHY during initialization.
+ */
+void mem_ctrl_init(int reset);
+
+ /* System Clock initialization */
+void system_clock_init(void);
+
+/*
+ * Init subsystems according to the reset status
+ *
+ * @return 0 for a normal boot, non-zero for a resume
+ */
+int do_lowlevel_init(void);
+
+void sdelay(unsigned long);
similarity index 97%
rename from board/samsung/smdk5250/dmc_common.c
rename to arch/arm/cpu/armv7/exynos/dmc_common.c
@@ -26,7 +26,8 @@
#include <asm/arch/spl.h>
#include "clock_init.h"
-#include "setup.h"
+#include "common_setup.h"
+#include "exynos5_setup.h"
#define ZQ_INIT_TIMEOUT 10000
@@ -175,7 +176,7 @@ void dmc_config_memory(struct mem_timings *mem, struct exynos5_dmc *dmc)
writel(DMC_MEMBASECONFIG1_VAL, &dmc->membaseconfig1);
}
-void mem_ctrl_init()
+void mem_ctrl_init(int reset)
{
struct spl_machine_param *param = spl_get_machine_params();
struct mem_timings *mem;
@@ -185,7 +186,7 @@ void mem_ctrl_init()
/* If there are any other memory variant, add their init call below */
if (param->mem_type == DDR_MODE_DDR3) {
- ret = ddr3_mem_ctrl_init(mem, param->mem_iv_size);
+ ret = ddr3_mem_ctrl_init(mem, param->mem_iv_size, reset);
if (ret) {
/* will hang if failed to init memory control */
while (1)
similarity index 92%
rename from board/samsung/smdk5250/dmc_init_ddr3.c
rename to arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c
@@ -27,31 +27,36 @@
#include <asm/arch/clock.h>
#include <asm/arch/cpu.h>
#include <asm/arch/dmc.h>
-#include "setup.h"
+#include "common_setup.h"
+#include "exynos5_setup.h"
#include "clock_init.h"
#define RDLVL_COMPLETE_TIMEOUT 10000
static void reset_phy_ctrl(void)
{
- struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE;
+ struct exynos5_clock *clk =
+ (struct exynos5_clock *)samsung_get_base_clock();
writel(DDR3PHY_CTRL_PHY_RESET_OFF, &clk->lpddr3phy_ctrl);
writel(DDR3PHY_CTRL_PHY_RESET, &clk->lpddr3phy_ctrl);
}
-int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size)
+int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size,
+ int reset)
{
unsigned int val;
struct exynos5_phy_control *phy0_ctrl, *phy1_ctrl;
struct exynos5_dmc *dmc;
int i;
- phy0_ctrl = (struct exynos5_phy_control *)EXYNOS5_DMC_PHY0_BASE;
- phy1_ctrl = (struct exynos5_phy_control *)EXYNOS5_DMC_PHY1_BASE;
- dmc = (struct exynos5_dmc *)EXYNOS5_DMC_CTRL_BASE;
+ phy0_ctrl = (struct exynos5_phy_control *)samsung_get_base_dmc_phy();
+ phy1_ctrl = (struct exynos5_phy_control *)(samsung_get_base_dmc_phy()
+ + DMC_OFFSET);
+ dmc = (struct exynos5_dmc *)samsung_get_base_dmc_ctrl();
- reset_phy_ctrl();
+ if (reset)
+ reset_phy_ctrl();
/* Set Impedance Output Driver */
val = (mem->impedance << CA_CK_DRVR_DS_OFFSET) |
@@ -100,14 +105,14 @@ int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size)
/* Start DLL locking */
writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
- &phy0_ctrl->phy_con12);
+ &phy0_ctrl->phy_con12);
writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
- &phy1_ctrl->phy_con12);
+ &phy1_ctrl->phy_con12);
update_reset_dll(dmc, DDR_MODE_DDR3);
writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT),
- &dmc->concontrol);
+ &dmc->concontrol);
/* Memory Channel Inteleaving Size */
writel(mem->iv_size, &dmc->ivcontrol);
@@ -119,7 +124,7 @@ int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size)
/* Precharge Configuration */
writel(mem->prechconfig_tp_cnt << PRECHCONFIG_TP_CNT_SHIFT,
- &dmc->prechconfig);
+ &dmc->prechconfig);
/* Power Down mode Configuration */
writel(mem->dpwrdn_cyc << PWRDNCONFIG_DPWRDN_CYC_SHIFT |
new file mode 100644
@@ -0,0 +1,213 @@
+/*
+ * Memory setup for board based on EXYNOS4210
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ * Rajeshwari Shinde <rajeshwari.s@samsung.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <asm/arch/dmc.h>
+#include "common_setup.h"
+#include "exynos4_setup.h"
+
+struct mem_timings mem = {
+ .direct_cmd_msr = {
+ DIRECT_CMD1, DIRECT_CMD2, DIRECT_CMD3, DIRECT_CMD4
+ },
+ .timingref = TIMINGREF_VAL,
+ .timingrow = TIMINGROW_VAL,
+ .timingdata = TIMINGDATA_VAL,
+ .timingpower = TIMINGPOWER_VAL,
+ .zqcontrol = ZQ_CONTROL_VAL,
+ .control0 = CONTROL0_VAL,
+ .control1 = CONTROL1_VAL,
+ .control2 = CONTROL2_VAL,
+ .concontrol = CONCONTROL_VAL,
+ .prechconfig = PRECHCONFIG,
+ .memcontrol = MEMCONTROL_VAL,
+ .memconfig0 = MEMCONFIG0_VAL,
+ .memconfig1 = MEMCONFIG1_VAL,
+ .dll_resync = FORCE_DLL_RESYNC,
+ .dll_on = DLL_CONTROL_ON,
+};
+static void phy_control_reset(int ctrl_no, struct exynos4_dmc *dmc)
+{
+ if (ctrl_no) {
+ writel((mem.control1 | (1 << mem.dll_resync)),
+ &dmc->phycontrol1);
+ writel((mem.control1 | (0 << mem.dll_resync)),
+ &dmc->phycontrol1);
+ } else {
+ writel((mem.control0 | (0 << mem.dll_on)),
+ &dmc->phycontrol0);
+ writel((mem.control0 | (1 << mem.dll_on)),
+ &dmc->phycontrol0);
+ }
+}
+
+static void dmc_config_mrs(struct exynos4_dmc *dmc, int chip)
+{
+ int i;
+ unsigned long mask = 0;
+
+ if (chip)
+ mask = DIRECT_CMD_CHIP1_SHIFT;
+
+ for (i = 0; i < MEM_TIMINGS_MSR_COUNT; i++) {
+ writel(mem.direct_cmd_msr[i] | mask,
+ &dmc->directcmd);
+ }
+}
+
+static void dmc_init(struct exynos4_dmc *dmc)
+{
+ /*
+ * DLL Parameter Setting:
+ * Termination: Enable R/W
+ * Phase Delay for DQS Cleaning: 180' Shift
+ */
+ writel(mem.control1, &dmc->phycontrol1);
+
+ /*
+ * ZQ Calibration
+ * Termination: Disable
+ * Auto Calibration Start: Enable
+ */
+ writel(mem.zqcontrol, &dmc->phyzqcontrol);
+ sdelay(0x100000);
+
+ /*
+ * Update DLL Information:
+ * Force DLL Resyncronization
+ */
+ phy_control_reset(1, dmc);
+ phy_control_reset(0, dmc);
+
+ /* Set DLL Parameters */
+ writel(mem.control1, &dmc->phycontrol1);
+
+ /* DLL Start */
+ writel((mem.control0 | CTRL_START | CTRL_DLL_ON), &dmc->phycontrol0);
+
+ writel(mem.control2, &dmc->phycontrol2);
+
+ /* Set Clock Ratio of Bus clock to Memory Clock */
+ writel(mem.concontrol, &dmc->concontrol);
+
+ /*
+ * Memor Burst length: 8
+ * Number of chips: 2
+ * Memory Bus width: 32 bit
+ * Memory Type: DDR3
+ * Additional Latancy for PLL: 1 Cycle
+ */
+ writel(mem.memcontrol, &dmc->memcontrol);
+
+ writel(mem.memconfig0, &dmc->memconfig0);
+ writel(mem.memconfig1, &dmc->memconfig1);
+
+ /* Config Precharge Policy */
+ writel(mem.prechconfig, &dmc->prechconfig);
+ /*
+ * TimingAref, TimingRow, TimingData, TimingPower Setting:
+ * Values as per Memory AC Parameters
+ */
+ writel(mem.timingref, &dmc->timingref);
+ writel(mem.timingrow, &dmc->timingrow);
+ writel(mem.timingdata, &dmc->timingdata);
+ writel(mem.timingpower, &dmc->timingpower);
+
+ /* Chip0: NOP Command: Assert and Hold CKE to high level */
+ writel(DIRECT_CMD_NOP, &dmc->directcmd);
+ sdelay(0x100000);
+
+ /* Chip0: EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */
+ dmc_config_mrs(dmc, 0);
+ sdelay(0x100000);
+
+ /* Chip0: ZQINIT */
+ writel(DIRECT_CMD_ZQ, &dmc->directcmd);
+ sdelay(0x100000);
+
+ writel((DIRECT_CMD_NOP | DIRECT_CMD_CHIP1_SHIFT), &dmc->directcmd);
+ sdelay(0x100000);
+
+ /* Chip1: EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */
+ dmc_config_mrs(dmc, 1);
+ sdelay(0x100000);
+
+ /* Chip1: ZQINIT */
+ writel((DIRECT_CMD_ZQ | DIRECT_CMD_CHIP1_SHIFT), &dmc->directcmd);
+ sdelay(0x100000);
+
+ phy_control_reset(1, dmc);
+ sdelay(0x100000);
+
+ /* turn on DREX0, DREX1 */
+ writel((mem.concontrol | AREF_EN), &dmc->concontrol);
+}
+
+void mem_ctrl_init(int reset)
+{
+ struct exynos4_dmc *dmc;
+
+ /*
+ * Async bridge configuration at CPU_core:
+ * 1: half_sync
+ * 0: full_sync
+ */
+ writel(1, ASYNC_CONFIG);
+#ifdef CONFIG_ORIGEN
+ /* Interleave: 2Bit, Interleave_bit1: 0x15, Interleave_bit0: 0x7 */
+ writel(APB_SFR_INTERLEAVE_CONF_VAL, EXYNOS4_MIU_BASE +
+ APB_SFR_INTERLEAVE_CONF_OFFSET);
+ /* Update MIU Configuration */
+ writel(APB_SFR_ARBRITATION_CONF_VAL, EXYNOS4_MIU_BASE +
+ APB_SFR_ARBRITATION_CONF_OFFSET);
+#else
+ writel(APB_SFR_INTERLEAVE_CONF_VAL, EXYNOS4_MIU_BASE +
+ APB_SFR_INTERLEAVE_CONF_OFFSET);
+ writel(INTERLEAVE_ADDR_MAP_START_ADDR, EXYNOS4_MIU_BASE +
+ ABP_SFR_INTERLEAVE_ADDRMAP_START_OFFSET);
+ writel(INTERLEAVE_ADDR_MAP_END_ADDR, EXYNOS4_MIU_BASE +
+ ABP_SFR_INTERLEAVE_ADDRMAP_END_OFFSET);
+ writel(INTERLEAVE_ADDR_MAP_EN, EXYNOS4_MIU_BASE +
+ ABP_SFR_SLV_ADDRMAP_CONF_OFFSET);
+#ifdef CONFIG_MIU_LINEAR
+ writel(SLAVE0_SINGLE_ADDR_MAP_START_ADDR, EXYNOS4_MIU_BASE +
+ ABP_SFR_SLV0_SINGLE_ADDRMAP_START_OFFSET);
+ writel(SLAVE0_SINGLE_ADDR_MAP_END_ADDR, EXYNOS4_MIU_BASE +
+ ABP_SFR_SLV0_SINGLE_ADDRMAP_END_OFFSET);
+ writel(SLAVE1_SINGLE_ADDR_MAP_START_ADDR, EXYNOS4_MIU_BASE +
+ ABP_SFR_SLV1_SINGLE_ADDRMAP_START_OFFSET);
+ writel(SLAVE1_SINGLE_ADDR_MAP_END_ADDR, EXYNOS4_MIU_BASE +
+ ABP_SFR_SLV1_SINGLE_ADDRMAP_END_OFFSET);
+ writel(APB_SFR_SLV_ADDR_MAP_CONF_VAL, EXYNOS4_MIU_BASE +
+ ABP_SFR_SLV_ADDRMAP_CONF_OFFSET);
+#endif
+#endif
+ /* DREX0 */
+ dmc = (struct exynos4_dmc *)samsung_get_base_dmc_ctrl();
+ dmc_init(dmc);
+ dmc = (struct exynos4_dmc *)(samsung_get_base_dmc_ctrl()
+ + DMC_OFFSET);
+ dmc_init(dmc);
+}
similarity index 65%
rename from board/samsung/origen/origen_setup.h
rename to arch/arm/cpu/armv7/exynos/exynos4_setup.h
@@ -1,5 +1,5 @@
/*
- * Machine Specific Values for ORIGEN board based on S5PV310
+ * Machine Specific Values for EXYNOS4012 based board
*
* Copyright (C) 2011 Samsung Electronics
*
@@ -29,98 +29,22 @@
#include <version.h>
#include <asm/arch/cpu.h>
-/* Offsets of clock registers (sources and dividers) */
-#define CLK_SRC_CPU_OFFSET 0x14200
-#define CLK_DIV_CPU0_OFFSET 0x14500
-#define CLK_DIV_CPU1_OFFSET 0x14504
-
-#define CLK_SRC_DMC_OFFSET 0x10200
-#define CLK_DIV_DMC0_OFFSET 0x10500
-#define CLK_DIV_DMC1_OFFSET 0x10504
-
-#define CLK_SRC_TOP0_OFFSET 0xC210
-#define CLK_SRC_TOP1_OFFSET 0xC214
-#define CLK_DIV_TOP_OFFSET 0xC510
-
-#define CLK_SRC_LEFTBUS_OFFSET 0x4200
-#define CLK_DIV_LEFTBUS_OFFSET 0x4500
-
-#define CLK_SRC_RIGHTBUS_OFFSET 0x8200
-#define CLK_DIV_RIGHTBUS_OFFSET 0x8500
-
-#define CLK_SRC_FSYS_OFFSET 0xC240
-#define CLK_DIV_FSYS1_OFFSET 0xC544
-#define CLK_DIV_FSYS2_OFFSET 0xC548
-#define CLK_DIV_FSYS3_OFFSET 0xC54C
-
-#define CLK_SRC_CAM_OFFSET 0xC220
-#define CLK_SRC_TV_OFFSET 0xC224
-#define CLK_SRC_MFC_OFFSET 0xC228
-#define CLK_SRC_G3D_OFFSET 0xC22C
-#define CLK_SRC_LCD0_OFFSET 0xC234
-#define CLK_SRC_PERIL0_OFFSET 0xC250
-
-#define CLK_DIV_CAM_OFFSET 0xC520
-#define CLK_DIV_TV_OFFSET 0xC524
-#define CLK_DIV_MFC_OFFSET 0xC528
-#define CLK_DIV_G3D_OFFSET 0xC52C
-#define CLK_DIV_LCD0_OFFSET 0xC534
-#define CLK_DIV_PERIL0_OFFSET 0xC550
-
-#define CLK_SRC_LCD0_OFFSET 0xC234
-
-#define APLL_LOCK_OFFSET 0x14000
-#define MPLL_LOCK_OFFSET 0x14008
-#define APLL_CON0_OFFSET 0x14100
-#define APLL_CON1_OFFSET 0x14104
-#define MPLL_CON0_OFFSET 0x14108
-#define MPLL_CON1_OFFSET 0x1410C
-
-#define EPLL_LOCK_OFFSET 0xC010
-#define VPLL_LOCK_OFFSET 0xC020
-#define EPLL_CON0_OFFSET 0xC110
-#define EPLL_CON1_OFFSET 0xC114
-#define VPLL_CON0_OFFSET 0xC120
-#define VPLL_CON1_OFFSET 0xC124
-
-/* DMC: DRAM Controllor Register offsets */
-#define DMC_CONCONTROL 0x00
-#define DMC_MEMCONTROL 0x04
-#define DMC_MEMCONFIG0 0x08
-#define DMC_MEMCONFIG1 0x0C
-#define DMC_DIRECTCMD 0x10
-#define DMC_PRECHCONFIG 0x14
-#define DMC_PHYCONTROL0 0x18
-#define DMC_PHYCONTROL1 0x1C
-#define DMC_PHYCONTROL2 0x20
-#define DMC_TIMINGAREF 0x30
-#define DMC_TIMINGROW 0x34
-#define DMC_TIMINGDATA 0x38
-#define DMC_TIMINGPOWER 0x3C
-#define DMC_PHYZQCONTROL 0x44
+#ifdef CONFIG_CLK_800_330_165
+#define DRAM_CLK_330
+#endif
+#ifdef CONFIG_CLK_1000_200_200
+#define DRAM_CLK_200
+#endif
+#ifdef CONFIG_CLK_1000_330_165
+#define DRAM_CLK_330
+#endif
+#ifdef CONFIG_CLK_1000_400_200
+#define DRAM_CLK_400
+#endif
/* Bus Configuration Register Address */
#define ASYNC_CONFIG 0x10010350
-/* MIU Config Register Offsets*/
-#define APB_SFR_INTERLEAVE_CONF_OFFSET 0x400
-#define APB_SFR_ARBRITATION_CONF_OFFSET 0xC00
-
-/* Offset for inform registers */
-#define INFORM0_OFFSET 0x800
-#define INFORM1_OFFSET 0x804
-
-/* GPIO Offsets for UART: GPIO Contol Register */
-#define EXYNOS4_GPIO_A0_CON_OFFSET 0x00
-#define EXYNOS4_GPIO_A1_CON_OFFSET 0x20
-
-/* UART Register offsets */
-#define ULCON_OFFSET 0x00
-#define UCON_OFFSET 0x04
-#define UFCON_OFFSET 0x08
-#define UBRDIV_OFFSET 0x28
-#define UFRACVAL_OFFSET 0x2C
-
/* CLK_SRC_CPU */
#define MUX_HPM_SEL_MOUTAPLL 0x0
#define MUX_HPM_SEL_SCLKMPLL 0x1
@@ -485,123 +409,186 @@
| (VPLL_MRR << 24) \
| (VPLL_MFR << 16) \
| (VPLL_K << 0))
-/*
- * UART GPIO_A0/GPIO_A1 Control Register Value
- * 0x2: UART Function
- */
-#define EXYNOS4_GPIO_A0_CON_VAL 0x22222222
-#define EXYNOS4_GPIO_A1_CON_VAL 0x222222
-
-/* ULCON: UART Line Control Value 8N1 */
-#define WORD_LEN_5_BIT 0x00
-#define WORD_LEN_6_BIT 0x01
-#define WORD_LEN_7_BIT 0x02
-#define WORD_LEN_8_BIT 0x03
-
-#define STOP_BIT_1 0x00
-#define STOP_BIT_2 0x01
-
-#define NO_PARITY 0x00
-#define ODD_PARITY 0x4
-#define EVEN_PARITY 0x5
-#define FORCED_PARITY_CHECK_AS_1 0x6
-#define FORCED_PARITY_CHECK_AS_0 0x7
-
-#define INFRAMODE_NORMAL 0x00
-#define INFRAMODE_INFRARED 0x01
-
-#define ULCON_VAL ((INFRAMODE_NORMAL << 6) \
- | (NO_PARITY << 3) \
- | (STOP_BIT_1 << 2) \
- | (WORD_LEN_8_BIT << 0))
-/*
- * UCON: UART Control Value
- * Tx_interrupt Type: Level
- * Rx_interrupt Type: Level
- * Rx Timeout Enabled: Yes
- * Rx-Error Atatus_Int Enable: Yes
- * Loop_Back: No
- * Break Signal: No
- * Transmit mode : Interrupt request/polling
- * Receive mode : Interrupt request/polling
- */
-#define TX_PULSE_INTERRUPT 0
-#define TX_LEVEL_INTERRUPT 1
-#define RX_PULSE_INTERRUPT 0
-#define RX_LEVEL_INTERRUPT 1
-
-#define RX_TIME_OUT ENABLE
-#define RX_ERROR_STATE_INT_ENB ENABLE
-#define LOOP_BACK DISABLE
-#define BREAK_SIGNAL DISABLE
-
-#define TX_MODE_DISABLED 0X00
-#define TX_MODE_IRQ_OR_POLL 0X01
-#define TX_MODE_DMA 0X02
-
-#define RX_MODE_DISABLED 0X00
-#define RX_MODE_IRQ_OR_POLL 0X01
-#define RX_MODE_DMA 0X02
-
-#define UCON_VAL ((TX_LEVEL_INTERRUPT << 9) \
- | (RX_LEVEL_INTERRUPT << 8) \
- | (RX_TIME_OUT << 7) \
- | (RX_ERROR_STATE_INT_ENB << 6) \
- | (LOOP_BACK << 5) \
- | (BREAK_SIGNAL << 4) \
- | (TX_MODE_IRQ_OR_POLL << 2) \
- | (RX_MODE_IRQ_OR_POLL << 0))
+/* DMC */
+#define DIRECT_CMD_NOP 0x07000000
+#define DIRECT_CMD_ZQ 0x0a000000
+#define DIRECT_CMD_CHIP1_SHIFT (1 << 20)
+#define MEM_TIMINGS_MSR_COUNT 4
+#define CTRL_START (1 << 0)
+#define CTRL_DLL_ON (1 << 1)
+#define AREF_EN (1 << 5)
+#define DRV_TYPE (1 << 6)
+
+struct mem_timings {
+ unsigned direct_cmd_msr[MEM_TIMINGS_MSR_COUNT];
+ unsigned timingref;
+ unsigned timingrow;
+ unsigned timingdata;
+ unsigned timingpower;
+ unsigned zqcontrol;
+ unsigned control0;
+ unsigned control1;
+ unsigned control2;
+ unsigned concontrol;
+ unsigned prechconfig;
+ unsigned memcontrol;
+ unsigned memconfig0;
+ unsigned memconfig1;
+ unsigned dll_resync;
+ unsigned dll_on;
+};
+
+/* MIU */
+/* MIU Config Register Offsets*/
+#define APB_SFR_INTERLEAVE_CONF_OFFSET 0x400
+#define APB_SFR_ARBRITATION_CONF_OFFSET 0xC00
+#define ABP_SFR_SLV_ADDRMAP_CONF_OFFSET 0x800
+#define ABP_SFR_INTERLEAVE_ADDRMAP_START_OFFSET 0x808
+#define ABP_SFR_INTERLEAVE_ADDRMAP_END_OFFSET 0x810
+#define ABP_SFR_SLV0_SINGLE_ADDRMAP_START_OFFSET 0x818
+#define ABP_SFR_SLV0_SINGLE_ADDRMAP_END_OFFSET 0x820
+#define ABP_SFR_SLV1_SINGLE_ADDRMAP_START_OFFSET 0x828
+#define ABP_SFR_SLV1_SINGLE_ADDRMAP_END_OFFSET 0x830
+
+#ifdef CONFIG_ORIGEN
+/* Interleave: 2Bit, Interleave_bit1: 0x15, Interleave_bit0: 0x7 */
+#define APB_SFR_INTERLEAVE_CONF_VAL 0x20001507
+#define APB_SFR_ARBRITATION_CONF_VAL 0x00000001
+#endif
-/*
- * UFCON: UART FIFO Control Value
- * Tx FIFO Trigger LEVEL: 2 Bytes (001)
- * Rx FIFO Trigger LEVEL: 2 Bytes (001)
- * Tx Fifo Reset: No
- * Rx Fifo Reset: No
- * FIFO Enable: Yes
- */
-#define TX_FIFO_TRIGGER_LEVEL_0_BYTES 0x00
-#define TX_FIFO_TRIGGER_LEVEL_2_BYTES 0x1
-#define TX_FIFO_TRIGGER_LEVEL_4_BYTES 0x2
-#define TX_FIFO_TRIGGER_LEVEL_6_BYTES 0x3
-#define TX_FIFO_TRIGGER_LEVEL_8_BYTES 0x4
-#define TX_FIFO_TRIGGER_LEVEL_10_BYTES 0x5
-#define TX_FIFO_TRIGGER_LEVEL_12_BYTES 0x6
-#define TX_FIFO_TRIGGER_LEVEL_14_BYTES 0x7
-
-#define RX_FIFO_TRIGGER_LEVEL_2_BYTES 0x0
-#define RX_FIFO_TRIGGER_LEVEL_4_BYTES 0x1
-#define RX_FIFO_TRIGGER_LEVEL_6_BYTES 0x2
-#define RX_FIFO_TRIGGER_LEVEL_8_BYTES 0x3
-#define RX_FIFO_TRIGGER_LEVEL_10_BYTES 0x4
-#define RX_FIFO_TRIGGER_LEVEL_12_BYTES 0x5
-#define RX_FIFO_TRIGGER_LEVEL_14_BYTES 0x6
-#define RX_FIFO_TRIGGER_LEVEL_16_BYTES 0x7
-
-#define TX_FIFO_TRIGGER_LEVEL TX_FIFO_TRIGGER_LEVEL_2_BYTES
-#define RX_FIFO_TRIGGER_LEVEL RX_FIFO_TRIGGER_LEVEL_4_BYTES
-#define TX_FIFO_RESET DISABLE
-#define RX_FIFO_RESET DISABLE
-#define FIFO_ENABLE ENABLE
-#define UFCON_VAL ((TX_FIFO_TRIGGER_LEVEL << 8) \
- | (RX_FIFO_TRIGGER_LEVEL << 4) \
- | (TX_FIFO_RESET << 2) \
- | (RX_FIFO_RESET << 1) \
- | (FIFO_ENABLE << 0))
-/*
- * Baud Rate Division Value
- * 115200 BAUD:
- * UBRDIV_VAL = SCLK_UART/((115200 * 16) - 1)
- * UBRDIV_VAL = (800 MHz)/((115200 * 16) - 1)
- */
-#define UBRDIV_VAL 0x35
+#define INTERLEAVE_ADDR_MAP_START_ADDR 0x40000000
+#define INTERLEAVE_ADDR_MAP_END_ADDR 0xbfffffff
+#define INTERLEAVE_ADDR_MAP_EN 0x00000001
-/*
- * Fractional Part of Baud Rate Divisor:
- * 115200 BAUD:
- * UBRFRACVAL = ((((SCLK_UART*10/(115200*16) -10))%10)*16/10)
- * UBRFRACVAL = ((((800MHz*10/(115200*16) -10))%10)*16/10)
- */
-#define UFRACVAL_VAL 0x4
+#ifdef CONFIG_MIU_1BIT_INTERLEAVED
+/* Interleave_bit0: 0xC*/
+#define APB_SFR_INTERLEAVE_CONF_VAL 0x0000000c
+#endif
+#ifdef CONFIG_MIU_2BIT_INTERLEAVED
+/* Interleave: 2Bit, Interleave_bit1: 0x15, Interleave_bit0: 0xc */
+#define APB_SFR_INTERLEAVE_CONF_VAL 0x2000150c
+#endif
+#define SLAVE0_SINGLE_ADDR_MAP_START_ADDR 0x40000000
+#define SLAVE0_SINGLE_ADDR_MAP_END_ADDR 0x7fffffff
+#define SLAVE1_SINGLE_ADDR_MAP_START_ADDR 0x80000000
+#define SLAVE1_SINGLE_ADDR_MAP_END_ADDR 0xbfffffff
+/* Enable SME0 and SME1*/
+#define APB_SFR_SLV_ADDR_MAP_CONF_VAL 0x00000006
+
+#define FORCE_DLL_RESYNC 3
+#define DLL_CONTROL_ON 1
+
+#define DIRECT_CMD1 0x00020000
+#define DIRECT_CMD2 0x00030000
+#define DIRECT_CMD3 0x00010002
+#define DIRECT_CMD4 0x00000328
+
+#define CTRL_ZQ_MODE_NOTERM (0x1 << 0)
+#define CTRL_ZQ_START (0x1 << 1)
+#define CTRL_ZQ_DIV (0 << 4)
+#define CTRL_ZQ_MODE_DDS (0x7 << 8)
+#define CTRL_ZQ_MODE_TERM (0x2 << 11)
+#define CTRL_ZQ_FORCE_IMPN (0x5 << 14)
+#define CTRL_ZQ_FORCE_IMPP (0x6 << 17)
+#define CTRL_DCC (0xE38 << 20)
+#define ZQ_CONTROL_VAL (CTRL_ZQ_MODE_NOTERM | CTRL_ZQ_START\
+ | CTRL_ZQ_DIV | CTRL_ZQ_MODE_DDS\
+ | CTRL_ZQ_MODE_TERM | CTRL_ZQ_FORCE_IMPN\
+ | CTRL_ZQ_FORCE_IMPP | CTRL_DCC)
+
+#define ASYNC (0 << 0)
+#define CLK_RATIO (1 << 1)
+#define DIV_PIPE (1 << 3)
+#define AWR_ON (1 << 4)
+#define AREF_DISABLE (0 << 5)
+#define DRV_TYPE_DISABLE (0 << 6)
+#define CHIP0_NOT_EMPTY (0 << 8)
+#define CHIP1_NOT_EMPTY (0 << 9)
+#define DQ_SWAP_DISABLE (0 << 10)
+#define QOS_FAST_DISABLE (0 << 11)
+#define RD_FETCH (0x3 << 12)
+#define TIMEOUT_LEVEL0 (0xFFF << 16)
+#define CONCONTROL_VAL (ASYNC | CLK_RATIO | DIV_PIPE | AWR_ON\
+ | AREF_DISABLE | DRV_TYPE_DISABLE\
+ | CHIP0_NOT_EMPTY | CHIP1_NOT_EMPTY\
+ | DQ_SWAP_DISABLE | QOS_FAST_DISABLE\
+ | RD_FETCH | TIMEOUT_LEVEL0)
+
+#define CLK_STOP_DISABLE (0 << 1)
+#define DPWRDN_DISABLE (0 << 2)
+#define DPWRDN_TYPE (0 << 3)
+#define TP_DISABLE (0 << 4)
+#define DSREF_DIABLE (0 << 5)
+#define ADD_LAT_PALL (1 << 6)
+#define MEM_TYPE_DDR3 (0x6 << 8)
+#define MEM_WIDTH_32 (0x2 << 12)
+#define NUM_CHIP_2 (1 << 16)
+#define BL_8 (0x3 << 20)
+#define MEMCONTROL_VAL (CLK_STOP_DISABLE | DPWRDN_DISABLE\
+ | DPWRDN_TYPE | TP_DISABLE | DSREF_DIABLE\
+ | ADD_LAT_PALL | MEM_TYPE_DDR3 | MEM_WIDTH_32\
+ | NUM_CHIP_2 | BL_8)
+
+
+#define CHIP_BANK_8 (0x3 << 0)
+#define CHIP_ROW_14 (0x2 << 4)
+#define CHIP_COL_10 (0x3 << 8)
+#define CHIP_MAP_INTERLEAVED (1 << 12)
+#define CHIP_MASK (0xe0 << 16)
+#ifdef CONFIG_MIU_LINEAR
+#define CHIP0_BASE (0x40 << 24)
+#define CHIP1_BASE (0x60 << 24)
+#else
+#define CHIP0_BASE (0x20 << 24)
+#define CHIP1_BASE (0x40 << 24)
+#endif
+#define MEMCONFIG0_VAL (CHIP_BANK_8 | CHIP_ROW_14 | CHIP_COL_10\
+ | CHIP_MAP_INTERLEAVED | CHIP_MASK | CHIP0_BASE)
+#define MEMCONFIG1_VAL (CHIP_BANK_8 | CHIP_ROW_14 | CHIP_COL_10\
+ | CHIP_MAP_INTERLEAVED | CHIP_MASK | CHIP1_BASE)
+
+#define TP_CNT (0xff << 24)
+#define PRECHCONFIG TP_CNT
+
+#define CTRL_OFF (0 << 0)
+#define CTRL_DLL_OFF (0 << 1)
+#define CTRL_HALF (0 << 2)
+#define CTRL_DFDQS (1 << 3)
+#define DQS_DELAY (0 << 4)
+#define CTRL_START_POINT (0x10 << 8)
+#define CTRL_INC (0x10 << 16)
+#define CTRL_FORCE (0x71 << 24)
+#define CONTROL0_VAL (CTRL_OFF | CTRL_DLL_OFF | CTRL_HALF\
+ | CTRL_DFDQS | DQS_DELAY | CTRL_START_POINT\
+ | CTRL_INC | CTRL_FORCE)
+
+#define CTRL_SHIFTC (0x6 << 0)
+#define CTRL_REF (8 << 4)
+#define CTRL_SHGATE (1 << 29)
+#define TERM_READ_EN (1 << 30)
+#define TERM_WRITE_EN (1 << 31)
+#define CONTROL1_VAL (CTRL_SHIFTC | CTRL_REF | CTRL_SHGATE\
+ | TERM_READ_EN | TERM_WRITE_EN)
+
+#define CONTROL2_VAL 0x00000000
+
+#ifdef CONFIG_ORIGEN
+#define TIMINGREF_VAL 0x000000BB
+#define TIMINGROW_VAL 0x4046654f
+#define TIMINGDATA_VAL 0x46400506
+#define TIMINGPOWER_VAL 0x52000A3C
+#else
+#define TIMINGREF_VAL 0x000000BC
+#ifdef DRAM_CLK_330
+#define TIMINGROW_VAL 0x3545548d
+#define TIMINGDATA_VAL 0x45430506
+#define TIMINGPOWER_VAL 0x4439033c
+#endif
+#ifdef DRAM_CLK_400
+#define TIMINGROW_VAL 0x45430506
+#define TIMINGDATA_VAL 0x56500506
+#define TIMINGPOWER_VAL 0x5444033d
+#endif
+#endif
#endif
similarity index 96%
rename from board/samsung/smdk5250/setup.h
rename to arch/arm/cpu/armv7/exynos/exynos5_setup.h
@@ -93,17 +93,17 @@
#define DMC_MEMCONTROL_MRR_BYTE_31_24 (3 << 25)
/* MEMCONFIG0 register bit fields */
-#define DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED (1 << 12)
-#define DMC_MEMCONFIGx_CHIP_COL_10 (3 << 8)
-#define DMC_MEMCONFIGx_CHIP_ROW_14 (2 << 4)
-#define DMC_MEMCONFIGx_CHIP_ROW_15 (3 << 4)
-#define DMC_MEMCONFIGx_CHIP_BANK_8 (3 << 0)
-
-#define DMC_MEMBASECONFIGx_CHIP_BASE(x) (x << 16)
-#define DMC_MEMBASECONFIGx_CHIP_MASK(x) (x << 0)
+#define DMC_MEMCONFIGX_CHIP_MAP_INTERLEAVED (1 << 12)
+#define DMC_MEMCONFIGX_CHIP_COL_10 (3 << 8)
+#define DMC_MEMCONFIGX_CHIP_ROW_14 (2 << 4)
+#define DMC_MEMCONFIGX_CHIP_ROW_15 (3 << 4)
+#define DMC_MEMCONFIGX_CHIP_BANK_8 (3 << 0)
+
+#define DMC_MEMBASECONFIGX_CHIP_BASE(x) (x << 16)
+#define DMC_MEMBASECONFIGX_CHIP_MASK(x) (x << 0)
#define DMC_MEMBASECONFIG_VAL(x) ( \
- DMC_MEMBASECONFIGx_CHIP_BASE(x) | \
- DMC_MEMBASECONFIGx_CHIP_MASK(0x780) \
+ DMC_MEMBASECONFIGX_CHIP_BASE(x) | \
+ DMC_MEMBASECONFIGX_CHIP_MASK(0x780) \
)
#define DMC_MEMBASECONFIG0_VAL DMC_MEMBASECONFIG_VAL(0x40)
@@ -513,9 +513,11 @@ enum {
* which the DMC uses to decide how to split a memory
* chunk into smaller chunks to support concurrent
* accesses; may vary across boards.
+ * @param reset Reset DDR PHY during initialization.
* @return 0 if ok, SETUP_ERR_... if there is a problem
*/
-int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size);
+int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size,
+ int reset);
/*
* Configure ZQ I/O interface
@@ -562,8 +564,4 @@ void dmc_config_memory(struct mem_timings *mem, struct exynos5_dmc *dmc);
* @param ddr_mode Type of DDR memory
*/
void update_reset_dll(struct exynos5_dmc *, enum ddr_mode);
-
-void sdelay(unsigned long);
-void mem_ctrl_init(void);
-void system_clock_init(void);
#endif
new file mode 100644
@@ -0,0 +1,73 @@
+/*
+ * Lowlevel setup for EXYNOS5 based board
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ * Rajeshwari Shinde <rajeshwari.s@samsung.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <config.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/dmc.h>
+#include <asm/arch/power.h>
+#include <asm/arch/tzpc.h>
+#include <asm/arch/periph.h>
+#include <asm/arch/pinmux.h>
+#include "common_setup.h"
+
+/* These are the things we can do during low-level init */
+enum {
+ DO_WAKEUP = 1 << 0,
+ DO_CLOCKS = 1 << 1,
+ DO_MEM_RESET = 1 << 2,
+ DO_UART = 1 << 3,
+};
+
+int do_lowlevel_init(void)
+{
+ uint32_t reset_status;
+ int actions = 0;
+
+ arch_cpu_init();
+
+ reset_status = get_reset_status();
+
+ switch (reset_status) {
+ case S5P_CHECK_SLEEP:
+ actions = DO_CLOCKS | DO_WAKEUP;
+ break;
+ case S5P_CHECK_DIDLE:
+ case S5P_CHECK_LPA:
+ actions = DO_WAKEUP;
+ break;
+ default:
+ /* This is a normal boot (not a wake from sleep) */
+ actions = DO_CLOCKS | DO_MEM_RESET;
+ }
+
+ if (actions & DO_CLOCKS) {
+ system_clock_init();
+ mem_ctrl_init(actions & DO_MEM_RESET);
+ tzpc_init();
+ }
+
+ return actions & DO_WAKEUP;
+}
similarity index 74%
rename from board/samsung/smdk5250/spl_boot.c
rename to arch/arm/cpu/armv7/exynos/spl_boot.c
@@ -23,13 +23,18 @@
#include<common.h>
#include<config.h>
-#include <asm/arch-exynos/dmc.h>
#include <asm/arch/clock.h>
#include <asm/arch/clk.h>
+#include <asm/arch/dmc.h>
+#include <asm/arch/power.h>
#include <asm/arch/spl.h>
+#include "common_setup.h"
#include "clock_init.h"
+DECLARE_GLOBAL_DATA_PTR;
+#define OM_STAT (0x1f << 1)
+
/* Index into irom ptr table */
enum index {
MMC_INDEX,
@@ -54,6 +59,7 @@ void *get_irom_func(int index)
return (void *)*(u32 *)irom_ptr_table[index];
}
+#ifdef CONFIG_USB_BOOTING
/*
* Set/clear program flow prediction and return the previous state.
*/
@@ -67,6 +73,7 @@ static int config_branch_prediction(int set_cr_z)
return cr & CR_Z;
}
+#endif
/*
* Copy U-boot from mmc to RAM:
@@ -75,35 +82,42 @@ static int config_branch_prediction(int set_cr_z)
*/
void copy_uboot_to_ram(void)
{
- int is_cr_z_set;
- unsigned int sec_boot_check;
enum boot_mode bootmode = BOOT_MODE_OM;
- u32 (*spi_copy)(u32 offset, u32 nblock, u32 dst);
- u32 (*copy_bl2)(u32 offset, u32 nblock, u32 dst);
+ u32 (*copy_bl2)(u32 offset, u32 nblock, u32 dst) = NULL;
+ u32 offset = 0, size = 0;
+#ifdef CONFIG_SUPPORT_EMMC_BOOT
u32 (*copy_bl2_from_emmc)(u32 nblock, u32 dst);
void (*end_bootop_from_emmc)(void);
+#endif
+#ifdef CONFIG_USB_BOOTING
u32 (*usb_copy)(void);
+ int is_cr_z_set;
+ unsigned int sec_boot_check;
/* Read iRAM location to check for secondary USB boot mode */
sec_boot_check = readl(EXYNOS_IRAM_SECONDARY_BASE);
if (sec_boot_check == EXYNOS_USB_SECONDARY_BOOT)
bootmode = BOOT_MODE_USB;
+#endif
if (bootmode == BOOT_MODE_OM)
- bootmode = readl(EXYNOS5_POWER_BASE) & OM_STAT;
+ bootmode = readl(samsung_get_base_power()) & OM_STAT;
switch (bootmode) {
+#ifdef CONFIG_SPI_BOOTING
case BOOT_MODE_SERIAL:
- spi_copy = get_irom_func(SPI_INDEX);
- spi_copy(SPI_FLASH_UBOOT_POS, CONFIG_BL2_SIZE,
- CONFIG_SYS_TEXT_BASE);
+ offset = SPI_FLASH_UBOOT_POS;
+ size = CONFIG_BL2_SIZE;
+ copy_bl2 = get_irom_func(SPI_INDEX);
break;
+#endif
case BOOT_MODE_MMC:
+ offset = BL2_START_OFFSET;
+ size = BL2_SIZE_BLOC_COUNT;
copy_bl2 = get_irom_func(MMC_INDEX);
- copy_bl2(BL2_START_OFFSET, BL2_SIZE_BLOC_COUNT,
- CONFIG_SYS_TEXT_BASE);
break;
+#ifdef CONFIG_SUPPORT_EMMC_BOOT
case BOOT_MODE_EMMC:
/* Set the FSYS1 clock divisor value for EMMC boot */
emmc_boot_clk_div_set();
@@ -114,6 +128,8 @@ void copy_uboot_to_ram(void)
copy_bl2_from_emmc(BL2_SIZE_BLOC_COUNT, CONFIG_SYS_TEXT_BASE);
end_bootop_from_emmc();
break;
+#endif
+#ifdef CONFIG_USB_BOOTING
case BOOT_MODE_USB:
/*
* iROM needs program flow prediction to be disabled
@@ -124,14 +140,50 @@ void copy_uboot_to_ram(void)
usb_copy();
config_branch_prediction(is_cr_z_set);
break;
+#endif
default:
break;
}
+
+ if (copy_bl2)
+ copy_bl2(offset, size, CONFIG_SYS_TEXT_BASE);
+}
+
+void memzero(void *s, size_t n)
+{
+ char *ptr = s;
+ size_t i;
+
+ for (i = 0; i < n; i++)
+ *ptr++ = '\0';
+}
+
+/**
+ * Set up the U-Boot global_data pointer
+ *
+ * This sets the address of the global data, and sets up basic values.
+ *
+ * @param gdp Value to give to gd
+ */
+static void setup_global_data(gd_t *gdp)
+{
+ gd = gdp;
+ memzero((void *)gd, sizeof(gd_t));
+ gd->flags |= GD_FLG_RELOC;
+ gd->baudrate = CONFIG_BAUDRATE;
+ gd->have_console = 1;
}
void board_init_f(unsigned long bootflag)
{
+ __aligned(8) gd_t local_gd;
__attribute__((noreturn)) void (*uboot)(void);
+
+ setup_global_data(&local_gd);
+
+ if (do_lowlevel_init())
+ power_exit_wakeup();
+
copy_uboot_to_ram();
/* Jump to U-Boot image */
@@ -40,8 +40,7 @@
#define EXYNOS4_WATCHDOG_BASE 0x10060000
#define EXYNOS4_TZPC_BASE 0x10110000
#define EXYNOS4_MIU_BASE 0x10600000
-#define EXYNOS4_DMC0_BASE 0x10400000
-#define EXYNOS4_DMC1_BASE 0x10410000
+#define EXYNOS4_DMC_CTRL_BASE 0x10400000
#define EXYNOS4_GPIO_PART2_BASE 0x11000000
#define EXYNOS4_GPIO_PART1_BASE 0x11400000
#define EXYNOS4_FIMD_BASE 0x11C00000
@@ -64,6 +63,7 @@
#define EXYNOS4_DP_BASE DEVICE_NOT_AVAILABLE
#define EXYNOS4_SPI_ISP_BASE DEVICE_NOT_AVAILABLE
#define EXYNOS4_ACE_SFR_BASE DEVICE_NOT_AVAILABLE
+#define EXYNOS4_DMC_PHY_BASE DEVICE_NOT_AVAILABLE
/* EXYNOS4X12 */
#define EXYNOS4X12_GPIO_PART3_BASE 0x03860000
@@ -76,8 +76,7 @@
#define EXYNOS4X12_SYSTIMER_BASE 0x10050000
#define EXYNOS4X12_WATCHDOG_BASE 0x10060000
#define EXYNOS4X12_TZPC_BASE 0x10110000
-#define EXYNOS4X12_DMC0_BASE 0x10600000
-#define EXYNOS4X12_DMC1_BASE 0x10610000
+#define EXYNOS4X12_DMC_CTRL_BASE 0x10600000
#define EXYNOS4X12_GPIO_PART4_BASE 0x106E0000
#define EXYNOS4X12_GPIO_PART2_BASE 0x11000000
#define EXYNOS4X12_GPIO_PART1_BASE 0x11400000
@@ -99,6 +98,7 @@
#define EXYNOS4X12_SPI_BASE DEVICE_NOT_AVAILABLE
#define EXYNOS4X12_SPI_ISP_BASE DEVICE_NOT_AVAILABLE
#define EXYNOS4X12_ACE_SFR_BASE DEVICE_NOT_AVAILABLE
+#define EXYNOS4X12_DMC_PHY_BASE DEVICE_NOT_AVAILABLE
/* EXYNOS5 Common*/
#define EXYNOS5_I2C_SPACING 0x10000
@@ -112,8 +112,7 @@
#define EXYNOS5_TZPC_BASE 0x10100000
#define EXYNOS5_WATCHDOG_BASE 0x101D0000
#define EXYNOS5_ACE_SFR_BASE 0x10830000
-#define EXYNOS5_DMC_PHY0_BASE 0x10C00000
-#define EXYNOS5_DMC_PHY1_BASE 0x10C10000
+#define EXYNOS5_DMC_PHY_BASE 0x10C00000
#define EXYNOS5_GPIO_PART3_BASE 0x10D10000
#define EXYNOS5_DMC_CTRL_BASE 0x10DD0000
#define EXYNOS5_GPIO_PART1_BASE 0x11400000
@@ -237,6 +236,8 @@ SAMSUNG_BASE(power, POWER_BASE)
SAMSUNG_BASE(spi, SPI_BASE)
SAMSUNG_BASE(spi_isp, SPI_ISP_BASE)
SAMSUNG_BASE(tzpc, TZPC_BASE)
+SAMSUNG_BASE(dmc_ctrl, DMC_CTRL_BASE)
+SAMSUNG_BASE(dmc_phy, DMC_PHY_BASE)
#endif
#endif /* _EXYNOS4_CPU_H */
@@ -24,19 +24,12 @@ include $(TOPDIR)/config.mk
LIB = $(obj)lib$(BOARD).o
-SOBJS := mem_setup.o
-SOBJS += lowlevel_init.o
-
ifndef CONFIG_SPL_BUILD
COBJS += origen.o
endif
-ifdef CONFIG_SPL_BUILD
-COBJS += mmc_boot.o
-endif
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS))
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
ALL +=$(obj).depend $(LIB)
deleted file mode 100644
@@ -1,357 +0,0 @@
-/*
- * Lowlevel setup for ORIGEN board based on EXYNOS4210
- *
- * Copyright (C) 2011 Samsung Electronics
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/cpu.h>
-#include "origen_setup.h"
-/*
- * Register usages:
- *
- * r5 has zero always
- * r7 has GPIO part1 base 0x11400000
- * r6 has GPIO part2 base 0x11000000
- */
-
-_TEXT_BASE:
- .word CONFIG_SYS_TEXT_BASE
-
- .globl lowlevel_init
-lowlevel_init:
- push {lr}
-
- /* r5 has always zero */
- mov r5, #0
- ldr r7, =EXYNOS4_GPIO_PART1_BASE
- ldr r6, =EXYNOS4_GPIO_PART2_BASE
-
- /* check reset status */
- ldr r0, =(EXYNOS4_POWER_BASE + INFORM1_OFFSET)
- ldr r1, [r0]
-
- /* AFTR wakeup reset */
- ldr r2, =S5P_CHECK_DIDLE
- cmp r1, r2
- beq exit_wakeup
-
- /* LPA wakeup reset */
- ldr r2, =S5P_CHECK_LPA
- cmp r1, r2
- beq exit_wakeup
-
- /* Sleep wakeup reset */
- ldr r2, =S5P_CHECK_SLEEP
- cmp r1, r2
- beq wakeup_reset
-
- /*
- * If U-boot is already running in ram, no need to relocate U-Boot.
- * Memory controller must be configured before relocating U-Boot
- * in ram.
- */
- ldr r0, =0x0ffffff /* r0 <- Mask Bits*/
- bic r1, pc, r0 /* pc <- current addr of code */
- /* r1 <- unmasked bits of pc */
- ldr r2, _TEXT_BASE /* r2 <- original base addr in ram */
- bic r2, r2, r0 /* r2 <- unmasked bits of r2*/
- cmp r1, r2 /* compare r1, r2 */
- beq 1f /* r0 == r1 then skip sdram init */
-
- /* init system clock */
- bl system_clock_init
-
- /* Memory initialize */
- bl mem_ctrl_asm_init
-
-1:
- /* for UART */
- bl uart_asm_init
- bl arch_cpu_init
- bl tzpc_init
- pop {pc}
-
-wakeup_reset:
- bl system_clock_init
- bl mem_ctrl_asm_init
- bl arch_cpu_init
- bl tzpc_init
-
-exit_wakeup:
- /* Load return address and jump to kernel */
- ldr r0, =(EXYNOS4_POWER_BASE + INFORM0_OFFSET)
-
- /* r1 = physical address of exynos4210_cpu_resume function */
- ldr r1, [r0]
-
- /* Jump to kernel*/
- mov pc, r1
- nop
- nop
-
-/*
- * system_clock_init: Initialize core clock and bus clock.
- * void system_clock_init(void)
- */
-system_clock_init:
- push {lr}
- ldr r0, =EXYNOS4_CLOCK_BASE
-
- /* APLL(1), MPLL(1), CORE(0), HPM(0) */
- ldr r1, =CLK_SRC_CPU_VAL
- ldr r2, =CLK_SRC_CPU_OFFSET
- str r1, [r0, r2]
-
- /* wait ?us */
- mov r1, #0x10000
-2: subs r1, r1, #1
- bne 2b
-
- ldr r1, =CLK_SRC_TOP0_VAL
- ldr r2, =CLK_SRC_TOP0_OFFSET
- str r1, [r0, r2]
-
- ldr r1, =CLK_SRC_TOP1_VAL
- ldr r2, =CLK_SRC_TOP1_OFFSET
- str r1, [r0, r2]
-
- /* DMC */
- ldr r1, =CLK_SRC_DMC_VAL
- ldr r2, =CLK_SRC_DMC_OFFSET
- str r1, [r0, r2]
-
- /*CLK_SRC_LEFTBUS */
- ldr r1, =CLK_SRC_LEFTBUS_VAL
- ldr r2, =CLK_SRC_LEFTBUS_OFFSET
- str r1, [r0, r2]
-
- /*CLK_SRC_RIGHTBUS */
- ldr r1, =CLK_SRC_RIGHTBUS_VAL
- ldr r2, =CLK_SRC_RIGHTBUS_OFFSET
- str r1, [r0, r2]
-
- /* SATA: SCLKMPLL(0), MMC[0:4]: SCLKMPLL(6) */
- ldr r1, =CLK_SRC_FSYS_VAL
- ldr r2, =CLK_SRC_FSYS_OFFSET
- str r1, [r0, r2]
-
- /* UART[0:4] */
- ldr r1, =CLK_SRC_PERIL0_VAL
- ldr r2, =CLK_SRC_PERIL0_OFFSET
- str r1, [r0, r2]
-
- /* CAM , FIMC 0-3 */
- ldr r1, =CLK_SRC_CAM_VAL
- ldr r2, =CLK_SRC_CAM_OFFSET
- str r1, [r0, r2]
-
- /* MFC */
- ldr r1, =CLK_SRC_MFC_VAL
- ldr r2, =CLK_SRC_MFC_OFFSET
- str r1, [r0, r2]
-
- /* G3D */
- ldr r1, =CLK_SRC_G3D_VAL
- ldr r2, =CLK_SRC_G3D_OFFSET
- str r1, [r0, r2]
-
- /* LCD0 */
- ldr r1, =CLK_SRC_LCD0_VAL
- ldr r2, =CLK_SRC_LCD0_OFFSET
- str r1, [r0, r2]
-
- /* wait ?us */
- mov r1, #0x10000
-3: subs r1, r1, #1
- bne 3b
-
- /* CLK_DIV_CPU0 */
- ldr r1, =CLK_DIV_CPU0_VAL
- ldr r2, =CLK_DIV_CPU0_OFFSET
- str r1, [r0, r2]
-
- /* CLK_DIV_CPU1 */
- ldr r1, =CLK_DIV_CPU1_VAL
- ldr r2, =CLK_DIV_CPU1_OFFSET
- str r1, [r0, r2]
-
- /* CLK_DIV_DMC0 */
- ldr r1, =CLK_DIV_DMC0_VAL
- ldr r2, =CLK_DIV_DMC0_OFFSET
- str r1, [r0, r2]
-
- /*CLK_DIV_DMC1 */
- ldr r1, =CLK_DIV_DMC1_VAL
- ldr r2, =CLK_DIV_DMC1_OFFSET
- str r1, [r0, r2]
-
- /* CLK_DIV_LEFTBUS */
- ldr r1, =CLK_DIV_LEFTBUS_VAL
- ldr r2, =CLK_DIV_LEFTBUS_OFFSET
- str r1, [r0, r2]
-
- /* CLK_DIV_RIGHTBUS */
- ldr r1, =CLK_DIV_RIGHTBUS_VAL
- ldr r2, =CLK_DIV_RIGHTBUS_OFFSET
- str r1, [r0, r2]
-
- /* CLK_DIV_TOP */
- ldr r1, =CLK_DIV_TOP_VAL
- ldr r2, =CLK_DIV_TOP_OFFSET
- str r1, [r0, r2]
-
- /* MMC[0:1] */
- ldr r1, =CLK_DIV_FSYS1_VAL /* 800(MPLL) / (15 + 1) */
- ldr r2, =CLK_DIV_FSYS1_OFFSET
- str r1, [r0, r2]
-
- /* MMC[2:3] */
- ldr r1, =CLK_DIV_FSYS2_VAL /* 800(MPLL) / (15 + 1) */
- ldr r2, =CLK_DIV_FSYS2_OFFSET
- str r1, [r0, r2]
-
- /* MMC4 */
- ldr r1, =CLK_DIV_FSYS3_VAL /* 800(MPLL) / (15 + 1) */
- ldr r2, =CLK_DIV_FSYS3_OFFSET
- str r1, [r0, r2]
-
- /* CLK_DIV_PERIL0: UART Clock Divisors */
- ldr r1, =CLK_DIV_PERIL0_VAL
- ldr r2, =CLK_DIV_PERIL0_OFFSET
- str r1, [r0, r2]
-
- /* CAM, FIMC 0-3: CAM Clock Divisors */
- ldr r1, =CLK_DIV_CAM_VAL
- ldr r2, =CLK_DIV_CAM_OFFSET
- str r1, [r0, r2]
-
- /* CLK_DIV_MFC: MFC Clock Divisors */
- ldr r1, =CLK_DIV_MFC_VAL
- ldr r2, =CLK_DIV_MFC_OFFSET
- str r1, [r0, r2]
-
- /* CLK_DIV_G3D: G3D Clock Divisors */
- ldr r1, =CLK_DIV_G3D_VAL
- ldr r2, =CLK_DIV_G3D_OFFSET
- str r1, [r0, r2]
-
- /* CLK_DIV_LCD0: LCD0 Clock Divisors */
- ldr r1, =CLK_DIV_LCD0_VAL
- ldr r2, =CLK_DIV_LCD0_OFFSET
- str r1, [r0, r2]
-
- /* Set PLL locktime */
- ldr r1, =PLL_LOCKTIME
- ldr r2, =APLL_LOCK_OFFSET
- str r1, [r0, r2]
-
- ldr r1, =PLL_LOCKTIME
- ldr r2, =MPLL_LOCK_OFFSET
- str r1, [r0, r2]
-
- ldr r1, =PLL_LOCKTIME
- ldr r2, =EPLL_LOCK_OFFSET
- str r1, [r0, r2]
-
- ldr r1, =PLL_LOCKTIME
- ldr r2, =VPLL_LOCK_OFFSET
- str r1, [r0, r2]
-
- /* APLL_CON1 */
- ldr r1, =APLL_CON1_VAL
- ldr r2, =APLL_CON1_OFFSET
- str r1, [r0, r2]
-
- /* APLL_CON0 */
- ldr r1, =APLL_CON0_VAL
- ldr r2, =APLL_CON0_OFFSET
- str r1, [r0, r2]
-
- /* MPLL_CON1 */
- ldr r1, =MPLL_CON1_VAL
- ldr r2, =MPLL_CON1_OFFSET
- str r1, [r0, r2]
-
- /* MPLL_CON0 */
- ldr r1, =MPLL_CON0_VAL
- ldr r2, =MPLL_CON0_OFFSET
- str r1, [r0, r2]
-
- /* EPLL */
- ldr r1, =EPLL_CON1_VAL
- ldr r2, =EPLL_CON1_OFFSET
- str r1, [r0, r2]
-
- /* EPLL_CON0 */
- ldr r1, =EPLL_CON0_VAL
- ldr r2, =EPLL_CON0_OFFSET
- str r1, [r0, r2]
-
- /* VPLL_CON1 */
- ldr r1, =VPLL_CON1_VAL
- ldr r2, =VPLL_CON1_OFFSET
- str r1, [r0, r2]
-
- /* VPLL_CON0 */
- ldr r1, =VPLL_CON0_VAL
- ldr r2, =VPLL_CON0_OFFSET
- str r1, [r0, r2]
-
- /* wait ?us */
- mov r1, #0x30000
-4: subs r1, r1, #1
- bne 4b
-
- pop {pc}
-/*
- * uart_asm_init: Initialize UART in asm mode, 115200bps fixed.
- * void uart_asm_init(void)
- */
- .globl uart_asm_init
-uart_asm_init:
-
- /* setup UART0-UART3 GPIOs (part1) */
- mov r0, r7
- ldr r1, =EXYNOS4_GPIO_A0_CON_VAL
- str r1, [r0, #EXYNOS4_GPIO_A0_CON_OFFSET]
- ldr r1, =EXYNOS4_GPIO_A1_CON_VAL
- str r1, [r0, #EXYNOS4_GPIO_A1_CON_OFFSET]
-
- ldr r0, =EXYNOS4_UART_BASE
- add r0, r0, #EXYNOS4_DEFAULT_UART_OFFSET
-
- ldr r1, =ULCON_VAL
- str r1, [r0, #ULCON_OFFSET]
- ldr r1, =UCON_VAL
- str r1, [r0, #UCON_OFFSET]
- ldr r1, =UFCON_VAL
- str r1, [r0, #UFCON_OFFSET]
- ldr r1, =UBRDIV_VAL
- str r1, [r0, #UBRDIV_OFFSET]
- ldr r1, =UFRACVAL_VAL
- str r1, [r0, #UFRACVAL_OFFSET]
- mov pc, lr
- nop
- nop
- nop
-
deleted file mode 100644
@@ -1,421 +0,0 @@
-/*
- * Memory setup for ORIGEN board based on EXYNOS4210
- *
- * Copyright (C) 2011 Samsung Electronics
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include "origen_setup.h"
-#define SET_MIU
-
- .globl mem_ctrl_asm_init
-mem_ctrl_asm_init:
- /*
- * Async bridge configuration at CPU_core:
- * 1: half_sync
- * 0: full_sync
- */
- ldr r0, =ASYNC_CONFIG
- mov r1, #1
- str r1, [r0]
-
-#ifdef SET_MIU
- ldr r0, =EXYNOS4_MIU_BASE
- /* Interleave: 2Bit, Interleave_bit1: 0x21, Interleave_bit2: 0x7 */
- ldr r1, =0x20001507
- str r1, [r0, #APB_SFR_INTERLEAVE_CONF_OFFSET]
-
- /* Update MIU Configuration */
- ldr r1, =0x00000001
- str r1, [r0, #APB_SFR_ARBRITATION_CONF_OFFSET]
-#endif
- /* DREX0 */
- ldr r0, =EXYNOS4_DMC0_BASE
-
- /*
- * DLL Parameter Setting:
- * Termination: Enable R/W
- * Phase Delay for DQS Cleaning: 180' Shift
- */
- ldr r1, =0xe0000086
- str r1, [r0, #DMC_PHYCONTROL1]
-
- /*
- * ZQ Calibration
- * Termination: Disable
- * Auto Calibration Start: Enable
- */
- ldr r1, =0xE3855703
- str r1, [r0, #DMC_PHYZQCONTROL]
-
- /* Wait ?us*/
- mov r2, #0x100000
-1: subs r2, r2, #1
- bne 1b
-
- /*
- * Update DLL Information:
- * Force DLL Resyncronization
- */
- ldr r1, =0xe000008e
- str r1, [r0, #DMC_PHYCONTROL1]
-
- /* Reset Force DLL Resyncronization */
- ldr r1, =0xe0000086
- str r1, [r0, #DMC_PHYCONTROL1]
-
- /* Enable Differential DQS, DLL Off*/
- ldr r1, =0x71101008
- str r1, [r0, #DMC_PHYCONTROL0]
-
- /* Activate PHY DLL: DLL On */
- ldr r1, =0x7110100A
- str r1, [r0, #DMC_PHYCONTROL0]
-
- /* Set DLL Parameters */
- ldr r1, =0xe0000086
- str r1, [r0, #DMC_PHYCONTROL1]
-
- /* DLL Start */
- ldr r1, =0x7110100B
- str r1, [r0, #DMC_PHYCONTROL0]
-
- ldr r1, =0x00000000
- str r1, [r0, #DMC_PHYCONTROL2]
-
- /* Set Clock Ratio of Bus clock to Memory Clock */
- ldr r1, =0x0FFF301a
- str r1, [r0, #DMC_CONCONTROL]
-
- /*
- * Memor Burst length: 8
- * Number of chips: 2
- * Memory Bus width: 32 bit
- * Memory Type: DDR3
- * Additional Latancy for PLL: 1 Cycle
- */
- ldr r1, =0x00312640
- str r1, [r0, #DMC_MEMCONTROL]
-
- /*
- * Memory Configuration Chip 0
- * Address Mapping: Interleaved
- * Number of Column address Bits: 10 bits
- * Number of Rows Address Bits: 14
- * Number of Banks: 8
- */
- ldr r1, =0x20e01323
- str r1, [r0, #DMC_MEMCONFIG0]
-
- /*
- * Memory Configuration Chip 1
- * Address Mapping: Interleaved
- * Number of Column address Bits: 10 bits
- * Number of Rows Address Bits: 14
- * Number of Banks: 8
- */
- ldr r1, =0x40e01323
- str r1, [r0, #DMC_MEMCONFIG1]
-
- /* Config Precharge Policy */
- ldr r1, =0xff000000
- str r1, [r0, #DMC_PRECHCONFIG]
-
- /*
- * TimingAref, TimingRow, TimingData, TimingPower Setting:
- * Values as per Memory AC Parameters
- */
- ldr r1, =0x000000BB
- str r1, [r0, #DMC_TIMINGAREF]
- ldr r1, =0x4046654f
- str r1, [r0, #DMC_TIMINGROW]
- ldr r1, =0x46400506
- str r1, [r0, #DMC_TIMINGDATA]
- ldr r1, =0x52000A3C
- str r1, [r0, #DMC_TIMINGPOWER]
-
- /* Chip0: NOP Command: Assert and Hold CKE to high level */
- ldr r1, =0x07000000
- str r1, [r0, #DMC_DIRECTCMD]
-
- /* Wait ?us*/
- mov r2, #0x100000
-2: subs r2, r2, #1
- bne 2b
-
- /* Chip0: EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */
- ldr r1, =0x00020000
- str r1, [r0, #DMC_DIRECTCMD]
- ldr r1, =0x00030000
- str r1, [r0, #DMC_DIRECTCMD]
- ldr r1, =0x00010002
- str r1, [r0, #DMC_DIRECTCMD]
- ldr r1, =0x00000328
- str r1, [r0, #DMC_DIRECTCMD]
-
- /* Wait ?us*/
- mov r2, #0x100000
-3: subs r2, r2, #1
- bne 3b
-
- /* Chip0: ZQINIT */
- ldr r1, =0x0a000000
- str r1, [r0, #DMC_DIRECTCMD]
-
- /* Wait ?us*/
- mov r2, #0x100000
-4: subs r2, r2, #1
- bne 4b
-
- /* Chip1: NOP Command: Assert and Hold CKE to high level */
- ldr r1, =0x07100000
- str r1, [r0, #DMC_DIRECTCMD]
-
- /* Wait ?us*/
- mov r2, #0x100000
-5: subs r2, r2, #1
- bne 5b
-
- /* Chip1: EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */
- ldr r1, =0x00120000
- str r1, [r0, #DMC_DIRECTCMD]
- ldr r1, =0x00130000
- str r1, [r0, #DMC_DIRECTCMD]
- ldr r1, =0x00110002
- str r1, [r0, #DMC_DIRECTCMD]
- ldr r1, =0x00100328
- str r1, [r0, #DMC_DIRECTCMD]
-
- /* Wait ?us*/
- mov r2, #0x100000
-6: subs r2, r2, #1
- bne 6b
-
- /* Chip1: ZQINIT */
- ldr r1, =0x0a100000
- str r1, [r0, #DMC_DIRECTCMD]
-
- /* Wait ?us*/
- mov r2, #0x100000
-7: subs r2, r2, #1
- bne 7b
-
- ldr r1, =0xe000008e
- str r1, [r0, #DMC_PHYCONTROL1]
- ldr r1, =0xe0000086
- str r1, [r0, #DMC_PHYCONTROL1]
-
- /* Wait ?us*/
- mov r2, #0x100000
-8: subs r2, r2, #1
- bne 8b
-
- /* DREX1 */
- ldr r0, =EXYNOS4_DMC1_BASE @0x10410000
-
- /*
- * DLL Parameter Setting:
- * Termination: Enable R/W
- * Phase Delay for DQS Cleaning: 180' Shift
- */
- ldr r1, =0xe0000086
- str r1, [r0, #DMC_PHYCONTROL1]
-
- /*
- * ZQ Calibration:
- * Termination: Disable
- * Auto Calibration Start: Enable
- */
- ldr r1, =0xE3855703
- str r1, [r0, #DMC_PHYZQCONTROL]
-
- /* Wait ?us*/
- mov r2, #0x100000
-1: subs r2, r2, #1
- bne 1b
-
- /*
- * Update DLL Information:
- * Force DLL Resyncronization
- */
- ldr r1, =0xe000008e
- str r1, [r0, #DMC_PHYCONTROL1]
-
- /* Reset Force DLL Resyncronization */
- ldr r1, =0xe0000086
- str r1, [r0, #DMC_PHYCONTROL1]
-
- /* Enable Differential DQS, DLL Off*/
- ldr r1, =0x71101008
- str r1, [r0, #DMC_PHYCONTROL0]
-
- /* Activate PHY DLL: DLL On */
- ldr r1, =0x7110100A
- str r1, [r0, #DMC_PHYCONTROL0]
-
- /* Set DLL Parameters */
- ldr r1, =0xe0000086
- str r1, [r0, #DMC_PHYCONTROL1]
-
- /* DLL Start */
- ldr r1, =0x7110100B
- str r1, [r0, #DMC_PHYCONTROL0]
-
- ldr r1, =0x00000000
- str r1, [r0, #DMC_PHYCONTROL2]
-
- /* Set Clock Ratio of Bus clock to Memory Clock */
- ldr r1, =0x0FFF301a
- str r1, [r0, #DMC_CONCONTROL]
-
- /*
- * Memor Burst length: 8
- * Number of chips: 2
- * Memory Bus width: 32 bit
- * Memory Type: DDR3
- * Additional Latancy for PLL: 1 Cycle
- */
- ldr r1, =0x00312640
- str r1, [r0, #DMC_MEMCONTROL]
-
- /*
- * Memory Configuration Chip 0
- * Address Mapping: Interleaved
- * Number of Column address Bits: 10 bits
- * Number of Rows Address Bits: 14
- * Number of Banks: 8
- */
- ldr r1, =0x20e01323
- str r1, [r0, #DMC_MEMCONFIG0]
-
- /*
- * Memory Configuration Chip 1
- * Address Mapping: Interleaved
- * Number of Column address Bits: 10 bits
- * Number of Rows Address Bits: 14
- * Number of Banks: 8
- */
- ldr r1, =0x40e01323
- str r1, [r0, #DMC_MEMCONFIG1]
-
- /* Config Precharge Policy */
- ldr r1, =0xff000000
- str r1, [r0, #DMC_PRECHCONFIG]
-
- /*
- * TimingAref, TimingRow, TimingData, TimingPower Setting:
- * Values as per Memory AC Parameters
- */
- ldr r1, =0x000000BB
- str r1, [r0, #DMC_TIMINGAREF]
- ldr r1, =0x4046654f
- str r1, [r0, #DMC_TIMINGROW]
- ldr r1, =0x46400506
- str r1, [r0, #DMC_TIMINGDATA]
- ldr r1, =0x52000A3C
- str r1, [r0, #DMC_TIMINGPOWER]
-
- /* Chip0: NOP Command: Assert and Hold CKE to high level */
- ldr r1, =0x07000000
- str r1, [r0, #DMC_DIRECTCMD]
-
- /* Wait ?us*/
- mov r2, #0x100000
-2: subs r2, r2, #1
- bne 2b
-
- /* Chip0: EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */
- ldr r1, =0x00020000
- str r1, [r0, #DMC_DIRECTCMD]
- ldr r1, =0x00030000
- str r1, [r0, #DMC_DIRECTCMD]
- ldr r1, =0x00010002
- str r1, [r0, #DMC_DIRECTCMD]
- ldr r1, =0x00000328
- str r1, [r0, #DMC_DIRECTCMD]
-
- /* Wait ?us*/
- mov r2, #0x100000
-3: subs r2, r2, #1
- bne 3b
-
- /* Chip 0: ZQINIT */
- ldr r1, =0x0a000000
- str r1, [r0, #DMC_DIRECTCMD]
-
- /* Wait ?us*/
- mov r2, #0x100000
-4: subs r2, r2, #1
- bne 4b
-
- /* Chip1: NOP Command: Assert and Hold CKE to high level */
- ldr r1, =0x07100000
- str r1, [r0, #DMC_DIRECTCMD]
-
- /* Wait ?us*/
- mov r2, #0x100000
-5: subs r2, r2, #1
- bne 5b
-
- /* Chip1: EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */
- ldr r1, =0x00120000
- str r1, [r0, #DMC_DIRECTCMD]
- ldr r1, =0x00130000
- str r1, [r0, #DMC_DIRECTCMD]
- ldr r1, =0x00110002
- str r1, [r0, #DMC_DIRECTCMD]
- ldr r1, =0x00100328
- str r1, [r0, #DMC_DIRECTCMD]
-
- /* Wait ?us*/
- mov r2, #0x100000
-6: subs r2, r2, #1
- bne 6b
-
- /* Chip1: ZQINIT */
- ldr r1, =0x0a100000
- str r1, [r0, #DMC_DIRECTCMD]
-
- /* Wait ?us*/
- mov r2, #0x100000
-7: subs r2, r2, #1
- bne 7b
-
- ldr r1, =0xe000008e
- str r1, [r0, #DMC_PHYCONTROL1]
- ldr r1, =0xe0000086
- str r1, [r0, #DMC_PHYCONTROL1]
-
- /* Wait ?us*/
- mov r2, #0x100000
-8: subs r2, r2, #1
- bne 8b
-
- /* turn on DREX0, DREX1 */
- ldr r0, =EXYNOS4_DMC0_BASE
- ldr r1, =0x0FFF303a
- str r1, [r0, #DMC_CONCONTROL]
-
- ldr r0, =EXYNOS4_DMC1_BASE
- ldr r1, =0x0FFF303a
- str r1, [r0, #DMC_CONCONTROL]
-
- mov pc, lr
deleted file mode 100644
@@ -1,58 +0,0 @@
-/*
- * Copyright (C) 2011 Samsung Electronics
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include<common.h>
-#include<config.h>
-
-/*
-* Copy U-boot from mmc to RAM:
-* COPY_BL2_FNPTR_ADDR: Address in iRAM, which Contains
-* Pointer to API (Data transfer from mmc to ram)
-*/
-void copy_uboot_to_ram(void)
-{
- u32 (*copy_bl2)(u32, u32, u32) = (void *) *(u32 *)COPY_BL2_FNPTR_ADDR;
-
- copy_bl2(BL2_START_OFFSET, BL2_SIZE_BLOC_COUNT, CONFIG_SYS_TEXT_BASE);
-}
-
-void board_init_f(unsigned long bootflag)
-{
- __attribute__((noreturn)) void (*uboot)(void);
- copy_uboot_to_ram();
-
- /* Jump to U-Boot image */
- uboot = (void *)CONFIG_SYS_TEXT_BASE;
- (*uboot)();
- /* Never returns Here */
-}
-
-/* Place Holders */
-void board_init_r(gd_t *id, ulong dest_addr)
-{
- /* Function attribute is no-return */
- /* This Function never executes */
- while (1)
- ;
-}
-
-void save_boot_params(u32 r0, u32 r1, u32 r2, u32 r3) {}
@@ -24,10 +24,6 @@ include $(TOPDIR)/config.mk
LIB = $(obj)lib$(BOARD).o
-SOBJS := lowlevel_init.o
-
-COBJS := clock_init.o
-COBJS += dmc_common.o dmc_init_ddr3.o
COBJS += smdk5250_spl.o
ifndef CONFIG_SPL_BUILD
@@ -38,14 +34,10 @@ COBJS += smdk5250.o
endif
endif
-ifdef CONFIG_SPL_BUILD
-COBJS += spl_boot.o
-endif
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS))
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
-ALL := $(obj).depend $(LIB)
+ALL := $(obj).depend $(LIB)
all: $(ALL)
@@ -24,18 +24,12 @@ include $(TOPDIR)/config.mk
LIB = $(obj)lib$(BOARD).o
-SOBJS := mem_setup.o
-SOBJS += lowlevel_init.o
ifndef CONFIG_SPL_BUILD
COBJS += smdkv310.o
endif
-ifdef CONFIG_SPL_BUILD
-COBJS += mmc_boot.o
-endif
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS))
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
ALL := $(obj).depend $(LIB)
deleted file mode 100644
@@ -1,414 +0,0 @@
-/*
- * Lowlevel setup for SMDKV310 board based on EXYNOS4210
- *
- * Copyright (C) 2011 Samsung Electronics
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/cpu.h>
-
-/*
- * Register usages:
- *
- * r5 has zero always
- * r7 has GPIO part1 base 0x11400000
- * r6 has GPIO part2 base 0x11000000
- */
-
-#define MEM_DLLl_ON
-
-_TEXT_BASE:
- .word CONFIG_SYS_TEXT_BASE
-
- .globl lowlevel_init
-lowlevel_init:
- push {lr}
-
- /* r5 has always zero */
- mov r5, #0
- ldr r7, =EXYNOS4_GPIO_PART1_BASE
- ldr r6, =EXYNOS4_GPIO_PART2_BASE
-
- /* check reset status */
- ldr r0, =(EXYNOS4_POWER_BASE + 0x81C) @ INFORM7
- ldr r1, [r0]
-
- /* AFTR wakeup reset */
- ldr r2, =S5P_CHECK_DIDLE
- cmp r1, r2
- beq exit_wakeup
-
- /* Sleep wakeup reset */
- ldr r2, =S5P_CHECK_SLEEP
- cmp r1, r2
- beq wakeup_reset
-
- /*
- * If U-boot is already running in ram, no need to relocate U-Boot.
- * Memory controller must be configured before relocating U-Boot
- * in ram.
- */
- ldr r0, =0x00ffffff /* r0 <- Mask Bits*/
- bic r1, pc, r0 /* pc <- current addr of code */
- /* r1 <- unmasked bits of pc */
-
- ldr r2, _TEXT_BASE /* r2 <- original base addr in ram */
- bic r2, r2, r0 /* r2 <- unmasked bits of r2*/
- cmp r1, r2 /* compare r1, r2 */
- beq 1f /* r0 == r1 then skip sdram init */
-
- /* init system clock */
- bl system_clock_init
-
- /* Memory initialize */
- bl mem_ctrl_asm_init
-
-1:
- /* for UART */
- bl uart_asm_init
- bl arch_cpu_init
- bl tzpc_init
- pop {pc}
-
-wakeup_reset:
- bl system_clock_init
- bl mem_ctrl_asm_init
- bl arch_cpu_init
- bl tzpc_init
-
-exit_wakeup:
- /* Load return address and jump to kernel */
- ldr r0, =(EXYNOS4_POWER_BASE + 0x800) @ INFORM0
-
- /* r1 = physical address of exynos4210_cpu_resume function */
- ldr r1, [r0]
-
- /* Jump to kernel*/
- mov pc, r1
- nop
- nop
-
-/*
- * system_clock_init: Initialize core clock and bus clock.
- * void system_clock_init(void)
- */
-system_clock_init:
- push {lr}
- ldr r0, =EXYNOS4_CLOCK_BASE
-
- /* APLL(1), MPLL(1), CORE(0), HPM(0) */
- ldr r1, =0x0101
- ldr r2, =0x14200 @CLK_SRC_CPU
- str r1, [r0, r2]
-
- /* wait ?us */
- mov r1, #0x10000
-2: subs r1, r1, #1
- bne 2b
-
- ldr r1, =0x00
- ldr r2, =0x0C210 @CLK_SRC_TOP0
- str r1, [r0, r2]
-
- ldr r1, =0x00
- ldr r2, =0x0C214 @CLK_SRC_TOP1_OFFSET
- str r1, [r0, r2]
-
- /* DMC */
- ldr r1, =0x00
- ldr r2, =0x10200 @CLK_SRC_DMC_OFFSET
- str r1, [r0, r2]
-
- /*CLK_SRC_LEFTBUS */
- ldr r1, =0x00
- ldr r2, =0x04200 @CLK_SRC_LEFTBUS_OFFSET
- str r1, [r0, r2]
-
- /*CLK_SRC_RIGHTBUS */
- ldr r1, =0x00
- ldr r2, =0x08200 @CLK_SRC_RIGHTBUS_OFFSET
- str r1, [r0, r2]
-
- /* SATA: SCLKMPLL(0), MMC[0:4]: SCLKMPLL(6) */
- ldr r1, =0x066666
- ldr r2, =0x0C240 @ CLK_SRC_FSYS
- str r1, [r0, r2]
-
- /* UART[0:4], PWM: SCLKMPLL(6) */
- ldr r1, =0x06666666
- ldr r2, =0x0C250 @CLK_SRC_PERIL0_OFFSET
- str r1, [r0, r2]
-
- /* wait ?us */
- mov r1, #0x10000
-3: subs r1, r1, #1
- bne 3b
-
- /*
- * CLK_DIV_CPU0:
- *
- * PCLK_DBG_RATIO[20] 0x1
- * ATB_RATIO[16] 0x3
- * PERIPH_RATIO[12] 0x3
- * COREM1_RATIO[8] 0x7
- * COREM0_RATIO[4] 0x3
- */
- ldr r1, =0x0133730
- ldr r2, =0x14500 @CLK_DIV_CPU0_OFFSET
- str r1, [r0, r2]
-
- /* CLK_DIV_CPU1: COPY_RATIO [0] 0x3 */
- ldr r1, =0x03
- ldr r2, =0x14504 @CLK_DIV_CPU1_OFFSET
- str r1, [r0, r2]
-
- /*
- * CLK_DIV_DMC0:
- *
- * CORE_TIMERS_RATIO[28] 0x1
- * COPY2_RATIO[24] 0x3
- * DMCP_RATIO[20] 0x1
- * DMCD_RATIO[16] 0x1
- * DMC_RATIO[12] 0x1
- * DPHY_RATIO[8] 0x1
- * ACP_PCLK_RATIO[4] 0x1
- * ACP_RATIO[0] 0x3
- */
- ldr r1, =0x13111113
- ldr r2, =0x010500 @CLK_DIV_DMC0_OFFSET
- str r1, [r0, r2]
-
- /*
- * CLK_DIV_DMC1:
- *
- * DPM_RATIO[24] 0x1
- * DVSEM_RATIO[16] 0x1
- * PWI_RATIO[8] 0x1
- */
- ldr r1, =0x01010100
- ldr r2, =0x010504 @CLK_DIV_DMC1_OFFSET
- str r1, [r0, r2]
-
- /*
- * CLK_DIV_LEFRBUS:
- *
- * GPL_RATIO[4] 0x1
- * GDL_RATIO[0] 0x3
- */
- ldr r1, =0x013
- ldr r2, =0x04500 @CLK_DIV_LEFTBUS_OFFSET
- str r1, [r0, r2]
-
- /*
- * CLK_DIV_RIGHTBUS:
- *
- * GPR_RATIO[4] 0x1
- * GDR_RATIO[0] 0x3
- */
- ldr r1, =0x013
- ldr r2, =0x08500 @CLK_DIV_RIGHTBUS_OFFSET
- str r1, [r0, r2]
-
- /*
- * CLK_DIV_TOP:
- *
- * ONENAND_RATIO[16] 0x0
- * ACLK_133_RATIO[12] 0x5
- * ACLK_160_RATIO[8] 0x4
- * ACLK_100_RATIO[4] 0x7
- * ACLK_200_RATIO[0] 0x3
- */
- ldr r1, =0x05473
- ldr r2, =0x0C510 @CLK_DIV_TOP_OFFSET
- str r1, [r0, r2]
-
- /* MMC[0:1] */
- ldr r1, =0x000f000f /* 800(MPLL) / (15 + 1) */
- ldr r2, =0x0C544 @ CLK_DIV_FSYS1
- str r1, [r0, r2]
-
- /* MMC[2:3] */
- ldr r1, =0x000f000f /* 800(MPLL) / (15 + 1) */
- ldr r2, =0x0C548 @ CLK_DIV_FSYS2
- str r1, [r0, r2]
-
- /* MMC4 */
- ldr r1, =0x000f /* 800(MPLL) / (15 + 1) */
- ldr r2, =0x0C54C @ CLK_DIV_FSYS3
- str r1, [r0, r2]
-
- /* wait ?us */
- mov r1, #0x10000
-4: subs r1, r1, #1
- bne 4b
-
- /*
- * CLK_DIV_PERIL0:
- *
- * UART5_RATIO[20] 8
- * UART4_RATIO[16] 8
- * UART3_RATIO[12] 8
- * UART2_RATIO[8] 8
- * UART1_RATIO[4] 8
- * UART0_RATIO[0] 8
- */
- ldr r1, =0x774777
- ldr r2, =0x0C550 @CLK_DIV_PERIL0_OFFSET
- str r1, [r0, r2]
-
- /* SLIMBUS: ???, PWM */
- ldr r1, =0x8
- ldr r2, =0x0C55C @ CLK_DIV_PERIL3
- str r1, [r0, r2]
-
- /* Set PLL locktime */
- ldr r1, =0x01C20
- ldr r2, =0x014000 @APLL_LOCK_OFFSET
- str r1, [r0, r2]
- ldr r1, =0x01C20
- ldr r2, =0x014008 @MPLL_LOCK_OFFSET
- str r1, [r0, r2]
- ldr r1, =0x01C20
- ldr r2, =0x0C010 @EPLL_LOCK_OFFSET
- str r1, [r0, r2]
- ldr r1, =0x01C20
- ldr r2, =0x0C020 @VPLL_LOCK_OFFSET
- str r1, [r0, r2]
-
- /*
- * APLL_CON1:
- *
- * APLL_AFC_ENB[31] 0x1
- * APLL_AFC[0] 0xC
- */
- ldr r1, =0x8000000C
- ldr r2, =0x014104 @APLL_CON1_OFFSET
- str r1, [r0, r2]
-
- /*
- * APLL_CON0:
- *
- * APLL_MDIV[16] 0xFA
- * APLL_PDIV[8] 0x6
- * APLL_SDIV[0] 0x1
- */
- ldr r1, =0x80FA0601
- ldr r2, =0x014100 @APLL_CON0_OFFSET
- str r1, [r0, r2]
-
- /*
- * MPLL_CON1:
- *
- * MPLL_AFC_ENB[31] 0x1
- * MPLL_AFC[0] 0x1C
- */
- ldr r1, =0x0000001C
- ldr r2, =0x01410C @MPLL_CON1_OFFSET
- str r1, [r0, r2]
-
- /*
- * MPLL_CON0:
- *
- * MPLL_MDIV[16] 0xC8
- * MPLL_PDIV[8] 0x6
- * MPLL_SDIV[0] 0x1
- */
- ldr r1, =0x80C80601
- ldr r2, =0x014108 @MPLL_CON0_OFFSET
- str r1, [r0, r2]
-
- /* EPLL */
- ldr r1, =0x0
- ldr r2, =0x0C114 @EPLL_CON1_OFFSET
- str r1, [r0, r2]
-
- /*
- * EPLL_CON0:
- *
- * EPLL_MDIV[16] 0x30
- * EPLL_PDIV[8] 0x3
- * EPLL_SDIV[0] 0x2
- */
- ldr r1, =0x80300302
- ldr r2, =0x0C110 @EPLL_CON0_OFFSET
- str r1, [r0, r2]
-
- /*
- * VPLL_CON1:
- *
- * VPLL_MRR[24] 0x11
- * VPLL_MFR[16] 0x0
- * VPLL_K[0] 0x400
- */
- ldr r1, =0x11000400
- ldr r2, =0x0C124 @VPLL_CON1_OFFSET
- str r1, [r0, r2]
-
- /*
- * VPLL_CON0:
- *
- * VPLL_MDIV[16] 0x35
- * VPLL_PDIV[8] 0x3
- * VPLL_SDIV[0] 0x2
- */
- ldr r1, =0x80350302
- ldr r2, =0x0C120 @VPLL_CON0_OFFSET
- str r1, [r0, r2]
-
- /* wait ?us */
- mov r1, #0x30000
-3: subs r1, r1, #1
- bne 3b
-
- pop {pc}
-/*
- * uart_asm_init: Initialize UART in asm mode, 115200bps fixed.
- * void uart_asm_init(void)
- */
- .globl uart_asm_init
-uart_asm_init:
-
- /* setup UART0-UART3 GPIOs (part1) */
- mov r0, r7
- ldr r1, =0x22222222
- str r1, [r0, #0x00] @ EXYNOS4_GPIO_A0_OFFSET
- ldr r1, =0x00222222
- str r1, [r0, #0x20] @ EXYNOS4_GPIO_A1_OFFSET
-
- ldr r0, =EXYNOS4_UART_BASE
- add r0, r0, #EXYNOS4_DEFAULT_UART_OFFSET
-
- ldr r1, =0x3C5
- str r1, [r0, #0x4]
- ldr r1, =0x111
- str r1, [r0, #0x8]
- ldr r1, =0x3
- str r1, [r0, #0x0]
- ldr r1, =0x35
- str r1, [r0, #0x28]
- ldr r1, =0x4
- str r1, [r0, #0x2c]
-
- mov pc, lr
- nop
- nop
- nop
deleted file mode 100644
@@ -1,365 +0,0 @@
-/*
- * Memory setup for SMDKV310 board based on EXYNOS4210
- *
- * Copyright (C) 2011 Samsung Electronics
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-
-#define SET_MIU
-
-#define MEM_DLL
-
-#ifdef CONFIG_CLK_800_330_165
-#define DRAM_CLK_330
-#endif
-#ifdef CONFIG_CLK_1000_200_200
-#define DRAM_CLK_200
-#endif
-#ifdef CONFIG_CLK_1000_330_165
-#define DRAM_CLK_330
-#endif
-#ifdef CONFIG_CLK_1000_400_200
-#define DRAM_CLK_400
-#endif
-
- .globl mem_ctrl_asm_init
-mem_ctrl_asm_init:
-
- /*
- * Async bridge configuration at CPU_core:
- * 1: half_sync
- * 0: full_sync
- */
- ldr r0, =0x10010350
- mov r1, #1
- str r1, [r0]
-
-#ifdef SET_MIU
- ldr r0, =EXYNOS4_MIU_BASE @0x10600000
-#ifdef CONFIG_MIU_1BIT_INTERLEAVED
- ldr r1, =0x0000000c
- str r1, [r0, #0x400] @MIU_INTLV_CONFIG
- ldr r1, =0x40000000
- str r1, [r0, #0x808] @MIU_INTLV_START_ADDR
- ldr r1, =0xbfffffff
- str r1, [r0, #0x810] @MIU_INTLV_END_ADDR
- ldr r1, =0x00000001
- str r1, [r0, #0x800] @MIU_MAPPING_UPDATE
-#endif
-#ifdef CONFIG_MIU_2BIT_INTERLEAVED
- ldr r1, =0x2000150c
- str r1, [r0, #0x400] @MIU_INTLV_CONFIG
- ldr r1, =0x40000000
- str r1, [r0, #0x808] @MIU_INTLV_START_ADDR
- ldr r1, =0xbfffffff
- str r1, [r0, #0x810] @MIU_INTLV_END_ADDR
- ldr r1, =0x00000001
- str r1, [r0, #0x800] @MIU_MAPPING_UPDATE
-#endif
-#ifdef CONFIG_MIU_LINEAR
- ldr r1, =0x40000000
- str r1, [r0, #0x818] @MIU_SINGLE_MAPPING0_START_ADDR
- ldr r1, =0x7fffffff
- str r1, [r0, #0x820] @MIU_SINGLE_MAPPING0_END_ADDR
- ldr r1, =0x80000000
- str r1, [r0, #0x828] @MIU_SINGLE_MAPPING1_START_ADDR
- ldr r1, =0xbfffffff
- str r1, [r0, #0x830] @MIU_SINGLE_MAPPING1_END_ADDR]
- ldr r1, =0x00000006
- str r1, [r0, #0x800] @MIU_MAPPING_UPDATE
-#endif
-#endif
- /* DREX0 */
- ldr r0, =EXYNOS4_DMC0_BASE @0x10400000
-
- ldr r1, =0xe0000086
- str r1, [r0, #0x1C] @DMC_PHYCONTROL1
-
- ldr r1, =0xE3855703
- str r1, [r0, #0x44] @DMC_PHYZQCONTROL
-
- mov r2, #0x100000
-1: subs r2, r2, #1
- bne 1b
-
- ldr r1, =0xe000008e
- str r1, [r0, #0x1C] @DMC_PHYCONTROL1
- ldr r1, =0xe0000086
- str r1, [r0, #0x1C] @DMC_PHYCONTROL1
-
- ldr r1, =0x71101008
- str r1, [r0, #0x18] @DMC_PHYCONTROL0
- ldr r1, =0x7110100A
- str r1, [r0, #0x18] @DMC_PHYCONTROL0
- ldr r1, =0xe0000086
- str r1, [r0, #0x1C] @DMC_PHYCONTROL1
- ldr r1, =0x7110100B
- str r1, [r0, #0x18] @DMC_PHYCONTROL0
-
- ldr r1, =0x00000000
- str r1, [r0, #0x20] @DMC_PHYCONTROL2
-
- ldr r1, =0x0FFF301a
- str r1, [r0, #0x00] @DMC_CONCONTROL
- ldr r1, =0x00312640
- str r1, [r0, #0x04] @DMC_MEMCONTROL]
-
-#ifdef CONFIG_MIU_LINEAR
- ldr r1, =0x40e01323
- str r1, [r0, #0x08] @DMC_MEMCONFIG0
- ldr r1, =0x60e01323
- str r1, [r0, #0x0C] @DMC_MEMCONFIG1
-#else /* @MIU_1BIT_INTERLEAVED | MIU_2BIT_INTERLEAVED */
- ldr r1, =0x20e01323
- str r1, [r0, #0x08] @DMC_MEMCONFIG0
- ldr r1, =0x40e01323
- str r1, [r0, #0x0C] @DMC_MEMCONFIG1
-#endif
-
- ldr r1, =0xff000000
- str r1, [r0, #0x14] @DMC_PRECHCONFIG
-
- ldr r1, =0x000000BC
- str r1, [r0, #0x30] @DMC_TIMINGAREF
-
-#ifdef DRAM_CLK_330
- ldr r1, =0x3545548d
- str r1, [r0, #0x34] @DMC_TIMINGROW
- ldr r1, =0x45430506
- str r1, [r0, #0x38] @DMC_TIMINGDATA
- ldr r1, =0x4439033c
- str r1, [r0, #0x3C] @DMC_TIMINGPOWER
-#endif
-#ifdef DRAM_CLK_400
- ldr r1, =0x4046654f
- str r1, [r0, #0x34] @DMC_TIMINGROW
- ldr r1, =0x56500506
- str r1, [r0, #0x38] @DMC_TIMINGDATA
- ldr r1, =0x5444033d
- str r1, [r0, #0x3C] @DMC_TIMINGPOWER
-#endif
- ldr r1, =0x07000000
- str r1, [r0, #0x10] @DMC_DIRECTCMD
-
- mov r2, #0x100000
-2: subs r2, r2, #1
- bne 2b
-
- ldr r1, =0x00020000
- str r1, [r0, #0x10] @DMC_DIRECTCMD
- ldr r1, =0x00030000
- str r1, [r0, #0x10] @DMC_DIRECTCMD
- ldr r1, =0x00010002
- str r1, [r0, #0x10] @DMC_DIRECTCMD
- ldr r1, =0x00000328
- str r1, [r0, #0x10] @DMC_DIRECTCMD
-
- mov r2, #0x100000
-3: subs r2, r2, #1
- bne 3b
-
- ldr r1, =0x0a000000
- str r1, [r0, #0x10] @DMC_DIRECTCMD
-
- mov r2, #0x100000
-4: subs r2, r2, #1
- bne 4b
-
- ldr r1, =0x07100000
- str r1, [r0, #0x10] @DMC_DIRECTCMD
-
- mov r2, #0x100000
-5: subs r2, r2, #1
- bne 5b
-
- ldr r1, =0x00120000
- str r1, [r0, #0x10] @DMC_DIRECTCMD
- ldr r1, =0x00130000
- str r1, [r0, #0x10] @DMC_DIRECTCMD
- ldr r1, =0x00110002
- str r1, [r0, #0x10] @DMC_DIRECTCMD
- ldr r1, =0x00100328
- str r1, [r0, #0x10] @DMC_DIRECTCMD
-
- mov r2, #0x100000
-6: subs r2, r2, #1
- bne 6b
-
- ldr r1, =0x0a100000
- str r1, [r0, #0x10] @DMC_DIRECTCMD
-
- mov r2, #0x100000
-7: subs r2, r2, #1
- bne 7b
-
- ldr r1, =0xe000008e
- str r1, [r0, #0x1C] @DMC_PHYCONTROL1
- ldr r1, =0xe0000086
- str r1, [r0, #0x1C] @DMC_PHYCONTROL1
-
- mov r2, #0x100000
-8: subs r2, r2, #1
- bne 8b
-
- /* DREX1 */
- ldr r0, =EXYNOS4_DMC1_BASE @0x10410000
-
- ldr r1, =0xe0000086
- str r1, [r0, #0x1C] @DMC_PHYCONTROL1
-
- ldr r1, =0xE3855703
- str r1, [r0, #0x44] @DMC_PHYZQCONTROL
-
- mov r2, #0x100000
-1: subs r2, r2, #1
- bne 1b
-
- ldr r1, =0xe000008e
- str r1, [r0, #0x1C] @DMC_PHYCONTROL1
- ldr r1, =0xe0000086
- str r1, [r0, #0x1C] @DMC_PHYCONTROL1
-
- ldr r1, =0x71101008
- str r1, [r0, #0x18] @DMC_PHYCONTROL0
- ldr r1, =0x7110100A
- str r1, [r0, #0x18] @DMC_PHYCONTROL0
- ldr r1, =0xe0000086
- str r1, [r0, #0x1C] @DMC_PHYCONTROL1
- ldr r1, =0x7110100B
- str r1, [r0, #0x18] @DMC_PHYCONTROL0
-
- ldr r1, =0x00000000
- str r1, [r0, #0x20] @DMC_PHYCONTROL2
-
- ldr r1, =0x0FFF301a
- str r1, [r0, #0x00] @DMC_CONCONTROL
- ldr r1, =0x00312640
- str r1, [r0, #0x04] @DMC_MEMCONTROL]
-
-#ifdef CONFIG_MIU_LINEAR
- ldr r1, =0x40e01323
- str r1, [r0, #0x08] @DMC_MEMCONFIG0
- ldr r1, =0x60e01323
- str r1, [r0, #0x0C] @DMC_MEMCONFIG1
-#else /* @MIU_1BIT_INTERLEAVED | MIU_2BIT_INTERLEAVED */
- ldr r1, =0x20e01323
- str r1, [r0, #0x08] @DMC_MEMCONFIG0
- ldr r1, =0x40e01323
- str r1, [r0, #0x0C] @DMC_MEMCONFIG1
-#endif
-
- ldr r1, =0xff000000
- str r1, [r0, #0x14] @DMC_PRECHCONFIG
-
- ldr r1, =0x000000BC
- str r1, [r0, #0x30] @DMC_TIMINGAREF
-
-#ifdef DRAM_CLK_330
- ldr r1, =0x3545548d
- str r1, [r0, #0x34] @DMC_TIMINGROW
- ldr r1, =0x45430506
- str r1, [r0, #0x38] @DMC_TIMINGDATA
- ldr r1, =0x4439033c
- str r1, [r0, #0x3C] @DMC_TIMINGPOWER
-#endif
-#ifdef DRAM_CLK_400
- ldr r1, =0x4046654f
- str r1, [r0, #0x34] @DMC_TIMINGROW
- ldr r1, =0x56500506
- str r1, [r0, #0x38] @DMC_TIMINGDATA
- ldr r1, =0x5444033d
- str r1, [r0, #0x3C] @DMC_TIMINGPOWER
-#endif
-
- ldr r1, =0x07000000
- str r1, [r0, #0x10] @DMC_DIRECTCMD
-
- mov r2, #0x100000
-2: subs r2, r2, #1
- bne 2b
-
- ldr r1, =0x00020000
- str r1, [r0, #0x10] @DMC_DIRECTCMD
- ldr r1, =0x00030000
- str r1, [r0, #0x10] @DMC_DIRECTCMD
- ldr r1, =0x00010002
- str r1, [r0, #0x10] @DMC_DIRECTCMD
- ldr r1, =0x00000328
- str r1, [r0, #0x10] @DMC_DIRECTCMD
-
- mov r2, #0x100000
-3: subs r2, r2, #1
- bne 3b
-
- ldr r1, =0x0a000000
- str r1, [r0, #0x10] @DMC_DIRECTCMD
-
- mov r2, #0x100000
-4: subs r2, r2, #1
- bne 4b
-
- ldr r1, =0x07100000
- str r1, [r0, #0x10] @DMC_DIRECTCMD
-
- mov r2, #0x100000
-5: subs r2, r2, #1
- bne 5b
-
- ldr r1, =0x00120000
- str r1, [r0, #0x10] @DMC_DIRECTCMD
- ldr r1, =0x00130000
- str r1, [r0, #0x10] @DMC_DIRECTCMD
- ldr r1, =0x00110002
- str r1, [r0, #0x10] @DMC_DIRECTCMD
- ldr r1, =0x00100328
- str r1, [r0, #0x10] @DMC_DIRECTCMD
-
- mov r2, #0x100000
-6: subs r2, r2, #1
- bne 6b
-
- ldr r1, =0x0a100000
- str r1, [r0, #0x10] @DMC_DIRECTCMD
-
- mov r2, #0x100000
-7: subs r2, r2, #1
- bne 7b
-
- ldr r1, =0xe000008e
- str r1, [r0, #0x1C] @DMC_PHYCONTROL1
- ldr r1, =0xe0000086
- str r1, [r0, #0x1C] @DMC_PHYCONTROL1
-
- mov r2, #0x100000
-8: subs r2, r2, #1
- bne 8b
-
- /* turn on DREX0, DREX1 */
- ldr r0, =0x10400000 @APB_DMC_0_BASE
- ldr r1, =0x0FFF303a
- str r1, [r0, #0x00] @DMC_CONCONTROL
-
- ldr r0, =0x10410000 @APB_DMC_1_BASE
- ldr r1, =0x0FFF303a
- str r1, [r0, #0x00] @DMC_CONCONTROL
-
- mov pc, lr
deleted file mode 100644
@@ -1,60 +0,0 @@
-/*
- * Copyright (C) 2011 Samsung Electronics
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include<common.h>
-#include<config.h>
-
-/*
-* Copy U-boot from mmc to RAM:
-* COPY_BL2_FNPTR_ADDR: Address in iRAM, which Contains
-* API (Data transfer from mmc to ram)
-*/
-void copy_uboot_to_ram(void)
-{
- u32 (*copy_bl2)(u32, u32, u32) = (void *)COPY_BL2_FNPTR_ADDR;
-
- copy_bl2(BL2_START_OFFSET, BL2_SIZE_BLOC_COUNT, CONFIG_SYS_TEXT_BASE);
-}
-
-void board_init_f(unsigned long bootflag)
-{
- __attribute__((noreturn)) void (*uboot)(void);
- copy_uboot_to_ram();
-
- /* Jump to U-Boot image */
- uboot = (void *)CONFIG_SYS_TEXT_BASE;
- (*uboot)();
- /* Never returns Here */
-}
-
-/* Place Holders */
-void board_init_r(gd_t *id, ulong dest_addr)
-{
- /*Function attribute is no-return*/
- /*This Function never executes*/
- while (1)
- ;
-}
-
-void save_boot_params(u32 r0, u32 r1, u32 r2, u32 r3)
-{
-}
@@ -104,6 +104,7 @@
#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_SKIP_LOWLEVEL_INIT
/* PWM */
#define CONFIG_PWM
@@ -137,6 +138,7 @@
#define CONFIG_USB_STORAGE
/* USB boot mode */
+#define CONFIG_USB_BOOTING
#define EXYNOS_COPY_USB_FNPTR_ADDR 0x02020070
#define EXYNOS_USB_SECONDARY_BOOT 0xfeed0002
#define EXYNOS_IRAM_SECONDARY_BASE 0x02020018
@@ -152,6 +154,8 @@
#define CONFIG_SPL
#define COPY_BL2_FNPTR_ADDR 0x02020030
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+
/* specific .lds file */
#define CONFIG_SPL_LDSCRIPT "board/samsung/common/exynos-uboot-spl.lds"
#define CONFIG_SPL_TEXT_BASE 0x02023400
@@ -229,7 +233,7 @@
#define BL2_START_OFFSET (CONFIG_BL2_OFFSET/512)
#define BL2_SIZE_BLOC_COUNT (CONFIG_BL2_SIZE/512)
-#define OM_STAT (0x1f << 1)
+#define CONFIG_SPI_BOOTING
#define EXYNOS_COPY_SPI_FNPTR_ADDR 0x02020058
#define SPI_FLASH_UBOOT_POS (CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE)
@@ -241,7 +245,7 @@
#define CONFIG_IRAM_STACK 0x02050000
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - 0x1000000)
+#define CONFIG_SYS_INIT_SP_ADDR CONFIG_IRAM_STACK
/* I2C */
#define CONFIG_SYS_I2C_INIT_BOARD
@@ -68,6 +68,8 @@
#define CONFIG_BAUDRATE 115200
#define EXYNOS4_DEFAULT_UART_OFFSET 0x020000
+#define CONFIG_SKIP_LOWLEVEL_INIT
+
/* SD/MMC configuration */
#define CONFIG_GENERIC_MMC
#define CONFIG_MMC
@@ -148,7 +150,10 @@
#define CONFIG_ENV_OFFSET (RESERVE_BLOCK_SIZE + BL1_SIZE)
#define CONFIG_DOS_PARTITION 1
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SPL_LDSCRIPT "board/samsung/common/exynos-uboot-spl.lds"
+#define CONFIG_SPL_MAX_FOOTPRINT (14 * 1024)
+
+#define CONFIG_SYS_INIT_SP_ADDR 0x02040000
/* U-boot copy size from boot Media to DRAM.*/
#define COPY_BL2_SIZE 0x80000
@@ -157,4 +162,5 @@
/* Enable devicetree support */
#define CONFIG_OF_LIBFDT
+
#endif /* __CONFIG_H */
@@ -58,6 +58,7 @@
/* Handling Sleep Mode*/
#define S5P_CHECK_SLEEP 0x00000BAD
#define S5P_CHECK_DIDLE 0xBAD00000
+#define S5P_CHECK_LPA 0xABAD0000
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (1 << 20))
@@ -94,6 +95,7 @@
/* MMC SPL */
#define CONFIG_SPL
+#define CONFIG_SKIP_LOWLEVEL_INIT
#define COPY_BL2_FNPTR_ADDR 0x00002488
#define CONFIG_SPL_TEXT_BASE 0x02021410
@@ -147,7 +149,10 @@
#define CONFIG_ENV_OFFSET (RESERVE_BLOCK_SIZE + BL1_SIZE)
#define CONFIG_DOS_PARTITION 1
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SPL_LDSCRIPT "board/samsung/common/exynos-uboot-spl.lds"
+#define CONFIG_SPL_MAX_FOOTPRINT (14 * 1024)
+
+#define CONFIG_SYS_INIT_SP_ADDR 0x02040000
/* U-boot copy size from boot Media to DRAM.*/
#define COPY_BL2_SIZE 0x80000
This patch performs the following: 1) Convert the assembly code for memory and clock initialization to C code. 2) Move the memory and clock init codes from board/samsung to arch/arm 3) Creat a common lowlevel_init file across Exynos4 and Exynos5. Converted the common lowlevel_init from assembly to C-code 4) Made spl_boot.c and tzpc_init.c common for both exynos4 and exynos5. 5) Enable CONFIG_SKIP_LOWLEVEL_INIT as stack pointer initialisation is already done in _main. 6) exynos-uboot-spl.lds made common across SMDKV310, Origen and SMDK5250. TEST: Tested SD-MMC boot on SMDK5250 and Origen. Tested USB and SPI boot on SMDK5250 Compile tested for SMDKV310. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> --- Changes in V2: - Rebased on latest u-boot-samsung tree. - Incorporated review comments from Minkyu Kang. Changes in V3: - Optimised the mem_ctrl_init function for exynos4. - Removed magic numbers. Changes in V4: - Used samsung_get_base api instead of hardcoding base address. arch/arm/cpu/armv7/exynos/Makefile | 17 +- .../arm/cpu/armv7/exynos}/clock_init.h | 0 arch/arm/cpu/armv7/exynos/clock_init_exynos4.c | 95 +++++ .../arm/cpu/armv7/exynos/clock_init_exynos5.c | 56 ++-- arch/arm/cpu/armv7/exynos/common_setup.h | 45 ++ .../arm/cpu/armv7/exynos}/dmc_common.c | 7 +- .../arm/cpu/armv7/exynos}/dmc_init_ddr3.c | 27 +- arch/arm/cpu/armv7/exynos/dmc_init_exynos4.c | 213 ++++++++++ .../arm/cpu/armv7/exynos/exynos4_setup.h | 397 +++++++++---------- .../arm/cpu/armv7/exynos/exynos5_setup.h | 28 +- arch/arm/cpu/armv7/exynos/lowlevel_init.c | 73 ++++ .../arm/cpu/armv7/exynos}/spl_boot.c | 74 +++- arch/arm/include/asm/arch-exynos/cpu.h | 13 +- board/samsung/origen/Makefile | 11 +- board/samsung/origen/lowlevel_init.S | 357 ----------------- board/samsung/origen/mem_setup.S | 421 -------------------- board/samsung/origen/mmc_boot.c | 58 --- board/samsung/smdk5250/Makefile | 14 +- board/samsung/smdkv310/Makefile | 10 +- board/samsung/smdkv310/lowlevel_init.S | 414 ------------------- board/samsung/smdkv310/mem_setup.S | 365 ----------------- board/samsung/smdkv310/mmc_boot.c | 60 --- include/configs/exynos5250-dt.h | 8 +- include/configs/origen.h | 8 +- include/configs/smdkv310.h | 7 +- 25 files changed, 788 insertions(+), 1990 deletions(-) rename {board/samsung/smdk5250 => arch/arm/cpu/armv7/exynos}/clock_init.h (100%) create mode 100644 arch/arm/cpu/armv7/exynos/clock_init_exynos4.c rename board/samsung/smdk5250/clock_init.c => arch/arm/cpu/armv7/exynos/clock_init_exynos5.c (94%) create mode 100644 arch/arm/cpu/armv7/exynos/common_setup.h rename {board/samsung/smdk5250 => arch/arm/cpu/armv7/exynos}/dmc_common.c (97%) rename {board/samsung/smdk5250 => arch/arm/cpu/armv7/exynos}/dmc_init_ddr3.c (92%) create mode 100644 arch/arm/cpu/armv7/exynos/dmc_init_exynos4.c rename board/samsung/origen/origen_setup.h => arch/arm/cpu/armv7/exynos/exynos4_setup.h (65%) rename board/samsung/smdk5250/setup.h => arch/arm/cpu/armv7/exynos/exynos5_setup.h (96%) create mode 100644 arch/arm/cpu/armv7/exynos/lowlevel_init.c rename {board/samsung/smdk5250 => arch/arm/cpu/armv7/exynos}/spl_boot.c (74%) delete mode 100644 board/samsung/origen/lowlevel_init.S delete mode 100644 board/samsung/origen/mem_setup.S delete mode 100644 board/samsung/origen/mmc_boot.c delete mode 100644 board/samsung/smdkv310/lowlevel_init.S delete mode 100644 board/samsung/smdkv310/mem_setup.S delete mode 100644 board/samsung/smdkv310/mmc_boot.c