@@ -4926,11 +4926,11 @@ static const struct regmap_range_cfg wcd9335_ranges[] = {
.name = "WCD9335",
.range_min = 0x0,
.range_max = WCD9335_MAX_REGISTER,
- .selector_reg = WCD9335_REG(0x0, 0),
+ .selector_reg = WCD9335_SEL_REGISTER,
.selector_mask = 0xff,
.selector_shift = 0,
- .window_start = 0x0,
- .window_len = 0x1000,
+ .window_start = 0x800,
+ .window_len = 0x100,
},
};
@@ -4968,12 +4968,12 @@ static const struct regmap_range_cfg wcd9335_ifc_ranges[] = {
{
.name = "WCD9335-IFC-DEV",
.range_min = 0x0,
- .range_max = WCD9335_REG(0, 0x7ff),
- .selector_reg = WCD9335_REG(0, 0x0),
- .selector_mask = 0xff,
+ .range_max = WCD9335_MAX_REGISTER,
+ .selector_reg = WCD9335_SEL_REGISTER,
+ .selector_mask = 0xfff,
.selector_shift = 0,
- .window_start = 0x0,
- .window_len = 0x1000,
+ .window_start = 0x800,
+ .window_len = 0x400,
},
};
@@ -4981,7 +4981,7 @@ static struct regmap_config wcd9335_ifc_regmap_config = {
.reg_bits = 16,
.val_bits = 8,
.can_multi_write = true,
- .max_register = WCD9335_REG(0, 0x7FF),
+ .max_register = WCD9335_MAX_REGISTER,
.ranges = wcd9335_ifc_ranges,
.num_ranges = ARRAY_SIZE(wcd9335_ifc_ranges),
};
@@ -8,9 +8,9 @@
* in slimbus mode the reg base starts from 0x800
* in i2s/i2c mode the reg base is 0x0
*/
-#define WCD9335_REG(pg, r) ((pg << 12) | (r) | 0x800)
+#define WCD9335_REG(pg, r) ((pg << 8) | (r))
#define WCD9335_REG_OFFSET(r) (r & 0xFF)
-#define WCD9335_PAGE_OFFSET(r) ((r >> 12) & 0xFF)
+#define WCD9335_PAGE_OFFSET(r) ((r >> 8) & 0xFF)
/* Page-0 Registers */
#define WCD9335_PAGE0_PAGE_REGISTER WCD9335_REG(0x00, 0x000)
@@ -600,7 +600,8 @@
#define WCD9335_CDC_CLK_RST_CTRL_FS_CNT_ENABLE BIT(0)
#define WCD9335_CDC_CLK_RST_CTRL_FS_CNT_DISABLE 0
#define WCD9335_CDC_TOP_TOP_CFG1 WCD9335_REG(0x0d, 0x082)
-#define WCD9335_MAX_REGISTER WCD9335_REG(0x80, 0x0FF)
+#define WCD9335_MAX_REGISTER 0xffff
+#define WCD9335_SEL_REGISTER 0x800
/* SLIMBUS Slave Registers */
#define WCD9335_SLIM_PGD_PORT_INT_EN0 WCD9335_REG(0, 0x30)
slimbus addresses are 16 bit wide, masking page numbers to wcd register at offset of 12 will limit the number for pages. So it becomes impossible to write to page 0x10 registers. Remove masking 0x800 (slimbus address range) from register address and making use of window parameters in regmap config should fix it and also will represent the registers exactly inline with Datasheet. Remove this unnessary masking and make the registers be inline with datasheet. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> --- sound/soc/codecs/wcd9335.c | 18 +++++++++--------- sound/soc/codecs/wcd9335.h | 7 ++++--- 2 files changed, 13 insertions(+), 12 deletions(-)