deleted file mode 100644
@@ -1,165 +0,0 @@
-NVIDIA Tegra186 GPIO controllers
-
-Tegra186 contains two GPIO controllers; a main controller and an "AON"
-controller. This binding document applies to both controllers. The register
-layouts for the controllers share many similarities, but also some significant
-differences. Hence, this document describes closely related but different
-bindings and compatible values.
-
-The Tegra186 GPIO controller allows software to set the IO direction of, and
-read/write the value of, numerous GPIO signals. Routing of GPIO signals to
-package balls is under the control of a separate pin controller HW block. Two
-major sets of registers exist:
-
-a) Security registers, which allow configuration of allowed access to the GPIO
-register set. These registers exist in a single contiguous block of physical
-address space. The size of this block, and the security features available,
-varies between the different GPIO controllers.
-
-Access to this set of registers is not necessary in all circumstances. Code
-that wishes to configure access to the GPIO registers needs access to these
-registers to do so. Code which simply wishes to read or write GPIO data does not
-need access to these registers.
-
-b) GPIO registers, which allow manipulation of the GPIO signals. In some GPIO
-controllers, these registers are exposed via multiple "physical aliases" in
-address space, each of which access the same underlying state. See the hardware
-documentation for rationale. Any particular GPIO client is expected to access
-just one of these physical aliases.
-
-Tegra HW documentation describes a unified naming convention for all GPIOs
-implemented by the SoC. Each GPIO is assigned to a port, and a port may control
-a number of GPIOs. Thus, each GPIO is named according to an alphabetical port
-name and an integer GPIO name within the port. For example, GPIO_PA0, GPIO_PN6,
-or GPIO_PCC3.
-
-The number of ports implemented by each GPIO controller varies. The number of
-implemented GPIOs within each port varies. GPIO registers within a controller
-are grouped and laid out according to the port they affect.
-
-The mapping from port name to the GPIO controller that implements that port, and
-the mapping from port name to register offset within a controller, are both
-extremely non-linear. The header file <dt-bindings/gpio/tegra186-gpio.h>
-describes the port-level mapping. In that file, the naming convention for ports
-matches the HW documentation. The values chosen for the names are alphabetically
-sorted within a particular controller. Drivers need to map between the DT GPIO
-IDs and HW register offsets using a lookup table.
-
-Each GPIO controller can generate a number of interrupt signals. Each signal
-represents the aggregate status for all GPIOs within a set of ports. Thus, the
-number of interrupt signals generated by a controller varies as a rough function
-of the number of ports it implements. Note that the HW documentation refers to
-both the overall controller HW module and the sets-of-ports as "controllers".
-
-Each GPIO controller in fact generates multiple interrupts signals for each set
-of ports. Each GPIO may be configured to feed into a specific one of the
-interrupt signals generated by a set-of-ports. The intent is for each generated
-signal to be routed to a different CPU, thus allowing different CPUs to each
-handle subsets of the interrupts within a port. The status of each of these
-per-port-set signals is reported via a separate register. Thus, a driver needs
-to know which status register to observe. This binding currently defines no
-configuration mechanism for this. By default, drivers should use register
-GPIO_${port}_INTERRUPT_STATUS_G1_0. Future revisions to the binding could
-define a property to configure this.
-
-Required properties:
-- compatible
- Array of strings.
- One of:
- - "nvidia,tegra186-gpio".
- - "nvidia,tegra186-gpio-aon".
- - "nvidia,tegra194-gpio".
- - "nvidia,tegra194-gpio-aon".
-- reg-names
- Array of strings.
- Contains a list of names for the register spaces described by the reg
- property. May contain the following entries, in any order:
- - "gpio": Mandatory. GPIO control registers. This may cover either:
- a) The single physical alias that this OS should use.
- b) All physical aliases that exist in the controller. This is
- appropriate when the OS is responsible for managing assignment of
- the physical aliases.
- - "security": Optional. Security configuration registers.
- Users of this binding MUST look up entries in the reg property by name,
- using this reg-names property to do so.
-- reg
- Array of (physical base address, length) tuples.
- Must contain one entry per entry in the reg-names property, in a matching
- order.
-- interrupts
- Array of interrupt specifiers.
- The interrupt outputs from the HW block, one per set of ports, in the
- order the HW manual describes them. The number of entries required varies
- depending on compatible value:
- - "nvidia,tegra186-gpio": 6 entries.
- - "nvidia,tegra186-gpio-aon": 1 entry.
- - "nvidia,tegra194-gpio": 6 entries.
- - "nvidia,tegra194-gpio-aon": 1 entry.
-- gpio-controller
- Boolean.
- Marks the device node as a GPIO controller/provider.
-- #gpio-cells
- Single-cell integer.
- Must be <2>.
- Indicates how many cells are used in a consumer's GPIO specifier.
- In the specifier:
- - The first cell is the pin number.
- See <dt-bindings/gpio/tegra186-gpio.h>.
- - The second cell contains flags:
- - Bit 0 specifies polarity
- - 0: Active-high (normal).
- - 1: Active-low (inverted).
-- interrupt-controller
- Boolean.
- Marks the device node as an interrupt controller/provider.
-- #interrupt-cells
- Single-cell integer.
- Must be <2>.
- Indicates how many cells are used in a consumer's interrupt specifier.
- In the specifier:
- - The first cell is the GPIO number.
- See <dt-bindings/gpio/tegra186-gpio.h>.
- - The second cell is contains flags:
- - Bits [3:0] indicate trigger type and level:
- - 1: Low-to-high edge triggered.
- - 2: High-to-low edge triggered.
- - 4: Active high level-sensitive.
- - 8: Active low level-sensitive.
- Valid combinations are 1, 2, 3, 4, 8.
-
-Example:
-
-#include <dt-bindings/interrupt-controller/irq.h>
-
-gpio@2200000 {
- compatible = "nvidia,tegra186-gpio";
- reg-names = "security", "gpio";
- reg =
- <0x0 0x2200000 0x0 0x10000>,
- <0x0 0x2210000 0x0 0x10000>;
- interrupts =
- <0 47 IRQ_TYPE_LEVEL_HIGH>,
- <0 50 IRQ_TYPE_LEVEL_HIGH>,
- <0 53 IRQ_TYPE_LEVEL_HIGH>,
- <0 56 IRQ_TYPE_LEVEL_HIGH>,
- <0 59 IRQ_TYPE_LEVEL_HIGH>,
- <0 180 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
-};
-
-gpio@c2f0000 {
- compatible = "nvidia,tegra186-gpio-aon";
- reg-names = "security", "gpio";
- reg =
- <0x0 0xc2f0000 0x0 0x1000>,
- <0x0 0xc2f1000 0x0 0x1000>;
- interrupts =
- <0 60 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
-};
new file mode 100644
@@ -0,0 +1,215 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/nvidia,tegra186-gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra GPIO Controller (Tegra186 and later)
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+description: |
+ Tegra186 contains two GPIO controllers; a main controller and an "AON"
+ controller. This binding document applies to both controllers. The register
+ layouts for the controllers share many similarities, but also some
+ significant differences. Hence, this document describes closely related but
+ different bindings and compatible values.
+
+ The Tegra186 GPIO controller allows software to set the IO direction of,
+ and read/write the value of, numerous GPIO signals. Routing of GPIO signals
+ to package balls is under the control of a separate pin controller hardware
+ block. Two major sets of registers exist:
+
+ a) Security registers, which allow configuration of allowed access to the
+ GPIO register set. These registers exist in a single contiguous block
+ of physical address space. The size of this block, and the security
+ features available, varies between the different GPIO controllers.
+
+ Access to this set of registers is not necessary in all circumstances.
+ Code that wishes to configure access to the GPIO registers needs access
+ to these registers to do so. Code which simply wishes to read or write
+ GPIO data does not need access to these registers.
+
+ b) GPIO registers, which allow manipulation of the GPIO signals. In some
+ GPIO controllers, these registers are exposed via multiple "physical
+ aliases" in address space, each of which access the same underlying
+ state. See the hardware documentation for rationale. Any particular
+ GPIO client is expected to access just one of these physical aliases.
+
+ Tegra HW documentation describes a unified naming convention for all GPIOs
+ implemented by the SoC. Each GPIO is assigned to a port, and a port may
+ control a number of GPIOs. Thus, each GPIO is named according to an
+ alphabetical port name and an integer GPIO name within the port. For
+ example, GPIO_PA0, GPIO_PN6, or GPIO_PCC3.
+
+ The number of ports implemented by each GPIO controller varies. The number
+ of implemented GPIOs within each port varies. GPIO registers within a
+ controller are grouped and laid out according to the port they affect.
+
+ The mapping from port name to the GPIO controller that implements that
+ port, and the mapping from port name to register offset within a
+ controller, are both extremely non-linear. The header file
+ <dt-bindings/gpio/tegra186-gpio.h> describes the port-level mapping. In
+ that file, the naming convention for ports matches the HW documentation.
+ The values chosen for the names are alphabetically sorted within a
+ particular controller. Drivers need to map between the DT GPIO IDs and HW
+ register offsets using a lookup table.
+
+ Each GPIO controller can generate a number of interrupt signals. Each
+ signal represents the aggregate status for all GPIOs within a set of
+ ports. Thus, the number of interrupt signals generated by a controller
+ varies as a rough function of the number of ports it implements. Note
+ that the HW documentation refers to both the overall controller HW
+ module and the sets-of-ports as "controllers".
+
+ Each GPIO controller in fact generates multiple interrupts signals for
+ each set of ports. Each GPIO may be configured to feed into a specific
+ one of the interrupt signals generated by a set-of-ports. The intent is
+ for each generated signal to be routed to a different CPU, thus allowing
+ different CPUs to each handle subsets of the interrupts within a port.
+ The status of each of these per-port-set signals is reported via a
+ separate register. Thus, a driver needs to know which status register to
+ observe. This binding currently defines no configuration mechanism for
+ this. By default, drivers should use register
+ GPIO_${port}_INTERRUPT_STATUS_G1_0. Future revisions to the binding could
+ define a property to configure this.
+
+properties:
+ compatible:
+ enum:
+ - nvidia,tegra186-gpio
+ - nvidia,tegra186-gpio-aon
+ - nvidia,tegra194-gpio
+ - nvidia,tegra194-gpio-aon
+
+ reg-names:
+ items:
+ - const: security
+ - const: gpio
+ minItems: 1
+ maxItems: 2
+
+ reg:
+ items:
+ - description: |
+ GPIO control registers. This may cover either:
+
+ a) The single physical alias that this OS should use.
+ b) All physical aliases that exist in the controller. This is
+ appropriate when the OS is responsible for managing assignment
+ of the physical aliases.
+ - description: Security configuration registers.
+ minItems: 1
+ maxItems: 2
+
+ interrupts:
+ description: The interrupt outputs from the HW block, one per set of
+ ports, in the order the HW manual describes them. The number of entries
+ required varies depending on compatible value.
+
+ gpio-controller:
+ description: Marks the device node as a GPIO controller/provider.
+ type: boolean
+
+ "#gpio-cells":
+ description: |
+ Indicates how many cells are used in a consumer's GPIO specifier. In the
+ specifier:
+
+ - The first cell is the pin number.
+ See <dt-bindings/gpio/tegra186-gpio.h>.
+ - The second cell contains flags:
+ - Bit 0 specifies polarity
+ - 0: Active-high (normal).
+ - 1: Active-low (inverted).
+ const: 2
+
+ interrupt-controller:
+ description: Marks the device node as an interrupt controller/provider.
+ type: boolean
+
+ "#interrupt-cells":
+ description: |
+ Indicates how many cells are used in a consumer's interrupt specifier.
+ In the specifier:
+
+ - The first cell is the GPIO number.
+ See <dt-bindings/gpio/tegra186-gpio.h>.
+ - The second cell is contains flags:
+ - Bits [3:0] indicate trigger type and level:
+ - 1: Low-to-high edge triggered.
+ - 2: High-to-low edge triggered.
+ - 4: Active high level-sensitive.
+ - 8: Active low level-sensitive.
+
+ Valid combinations are 1, 2, 3, 4, 8.
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - nvidia,tegra186-gpio
+ - nvidia,tegra194-gpio
+ then:
+ properties:
+ interrupts:
+ minItems: 6
+ maxItems: 6
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - nvidia,tegra186-gpio-aon
+ - nvidia,tegra194-gpio-aon
+ then:
+ properties:
+ interrupts:
+ minItems: 1
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - interrupts
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ gpio@2200000 {
+ compatible = "nvidia,tegra186-gpio";
+ reg-names = "security", "gpio";
+ reg = <0x0 0x2200000 0x0 0x10000>,
+ <0x0 0x2210000 0x0 0x10000>;
+ interrupts = <0 47 IRQ_TYPE_LEVEL_HIGH>,
+ <0 50 IRQ_TYPE_LEVEL_HIGH>,
+ <0 53 IRQ_TYPE_LEVEL_HIGH>,
+ <0 56 IRQ_TYPE_LEVEL_HIGH>,
+ <0 59 IRQ_TYPE_LEVEL_HIGH>,
+ <0 180 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio@c2f0000 {
+ compatible = "nvidia,tegra186-gpio-aon";
+ reg-names = "security", "gpio";
+ reg = <0x0 0xc2f0000 0x0 0x1000>,
+ <0x0 0xc2f1000 0x0 0x1000>;
+ interrupts = <0 60 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };