@@ -9,4 +9,12 @@ source "drivers/mtd/nand/onenand/Kconfig"
source "drivers/mtd/nand/raw/Kconfig"
source "drivers/mtd/nand/spi/Kconfig"
+menu "ECC engine support"
+
+config MTD_NAND_ECC
+ bool
+ depends on MTD_NAND_CORE
+
+endmenu
+
endmenu
@@ -6,3 +6,5 @@ obj-$(CONFIG_MTD_NAND_CORE) += nandcore.o
obj-y += onenand/
obj-y += raw/
obj-y += spi/
+
+nandcore-$(CONFIG_MTD_NAND_ECC) += ecc.o
new file mode 100644
@@ -0,0 +1,157 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Generic Error-Correcting Code (ECC) engine
+ *
+ * Copyright (C) 2019 Macronix
+ * Author:
+ * Miquèl RAYNAL <miquel.raynal@bootlin.com>
+ *
+ *
+ * This file describes the abstraction of any NAND ECC engine. It has been
+ * designed to fit most cases, including parallel NANDs and SPI-NANDs.
+ *
+ * There are three main situations where instantiating this ECC engine makes
+ * sense:
+ * - external: The ECC engine is outside the NAND pipeline, typically this
+ * is a software ECC engine, or an hardware engine that is
+ * outside the NAND controller pipeline.
+ * - pipelined: The ECC engine is inside the NAND pipeline, ie. on the
+ * controller's side. This is the case of most of the raw NAND
+ * controllers. In the pipeline case, the ECC bytes are
+ * generated/data corrected on the fly when a page is
+ * written/read.
+ * - ondie: The ECC engine is inside the NAND pipeline, on the chip's side.
+ * Some NAND chips can correct themselves the data.
+ *
+ * Besides the initial setup and final cleanups, the interfaces are rather
+ * simple:
+ * - prepare: Prepare an I/O request. Enable/disable the ECC engine based on
+ * the I/O request type. In case of software correction or external
+ * engine, this step may involve to derive the ECC bytes and place
+ * them in the OOB area before a write.
+ * - finish: Finish an I/O request. Correct the data in case of a read
+ * request and report the number of corrected bits/uncorrectable
+ * errors. Most likely empty for write operations, unless you have
+ * hardware specific stuff to do, like shutting down the engine to
+ * save power.
+ *
+ * The I/O request should be enclosed in a prepare()/finish() pair of calls
+ * and will behave differently depending on the requested I/O type:
+ * - raw: Correction disabled
+ * - ecc: Correction enabled
+ *
+ * The request direction is impacting the logic as well:
+ * - read: Load data from the NAND chip
+ * - write: Store data in the NAND chip
+ *
+ * Mixing all this combinations together gives the following behavior.
+ * Those are just examples, drivers are free to add custom steps in their
+ * prepare/finish hook.
+ *
+ * [external ECC engine]
+ * - external + prepare + raw + read: do nothing
+ * - external + finish + raw + read: do nothing
+ * - external + prepare + raw + write: do nothing
+ * - external + finish + raw + write: do nothing
+ * - external + prepare + ecc + read: do nothing
+ * - external + finish + ecc + read: calculate expected ECC bytes, extract
+ * ECC bytes from OOB buffer, correct
+ * and report any bitflip/error
+ * - external + prepare + ecc + write: calculate ECC bytes and store them at
+ * the right place in the OOB buffer based
+ * on the OOB layout
+ * - external + finish + ecc + write: do nothing
+ *
+ * [pipelined ECC engine]
+ * - pipelined + prepare + raw + read: disable the controller's ECC engine if
+ * activated
+ * - pipelined + finish + raw + read: do nothing
+ * - pipelined + prepare + raw + write: disable the controller's ECC engine if
+ * activated
+ * - pipelined + finish + raw + write: do nothing
+ * - pipelined + prepare + ecc + read: enable the controller's ECC engine if
+ * deactivated
+ * - pipelined + finish + ecc + read: check the status, report any
+ * error/bitflip
+ * - pipelined + prepare + ecc + write: enable the controller's ECC engine if
+ * deactivated
+ * - pipelined + finish + ecc + write: do nothing
+ *
+ * [ondie ECC engine]
+ * - ondie + prepare + raw + read: send commands to disable the on-chip ECC
+ * engine if activated
+ * - ondie + finish + raw + read: do nothing
+ * - ondie + prepare + raw + write: send commands to disable the on-chip ECC
+ * engine if activated
+ * - ondie + finish + raw + write: do nothing
+ * - ondie + prepare + ecc + read: send commands to enable the on-chip ECC
+ * engine if deactivated
+ * - ondie + finish + ecc + read: send commands to check the status, report
+ * any error/bitflip
+ * - ondie + prepare + ecc + write: send commands to enable the on-chip ECC
+ * engine if deactivated
+ * - ondie + finish + ecc + write: do nothing
+ */
+
+#include <linux/module.h>
+#include <linux/mtd/nand.h>
+
+/**
+ * nand_ecc_init_ctx - Init the ECC engine context
+ * @nand: the NAND device
+ *
+ * On success, the caller is responsible of calling @nand_ecc_cleanup_ctx().
+ */
+int nand_ecc_init_ctx(struct nand_device *nand)
+{
+ if (!nand->ecc.engine->ops->init_ctx)
+ return 0;
+
+ return nand->ecc.engine->ops->init_ctx(nand);
+}
+EXPORT_SYMBOL(nand_ecc_init_ctx);
+
+/**
+ * nand_ecc_cleanup_ctx - Cleanup the ECC engine context
+ * @nand: the NAND device
+ */
+void nand_ecc_cleanup_ctx(struct nand_device *nand)
+{
+ if (nand->ecc.engine->ops->cleanup_ctx)
+ nand->ecc.engine->ops->cleanup_ctx(nand);
+}
+EXPORT_SYMBOL(nand_ecc_cleanup_ctx);
+
+/**
+ * nand_ecc_prepare_io_req - Prepare an I/O request
+ * @nand: the NAND device
+ * @req: the I/O request
+ */
+int nand_ecc_prepare_io_req(struct nand_device *nand,
+ struct nand_page_io_req *req)
+{
+ if (!nand->ecc.engine->ops->prepare_io_req)
+ return 0;
+
+ return nand->ecc.engine->ops->prepare_io_req(nand, req);
+}
+EXPORT_SYMBOL(nand_ecc_prepare_io_req);
+
+/**
+ * nand_ecc_finish_io_req - Finish an I/O request
+ * @nand: the NAND device
+ * @req: the I/O request
+ */
+int nand_ecc_finish_io_req(struct nand_device *nand,
+ struct nand_page_io_req *req)
+{
+ if (!nand->ecc.engine->ops->finish_io_req)
+ return 0;
+
+ return nand->ecc.engine->ops->finish_io_req(nand, req);
+}
+EXPORT_SYMBOL(nand_ecc_finish_io_req);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Miquel Raynal <miquel.raynal@bootlin.com>");
+MODULE_DESCRIPTION("Generic ECC engine");
@@ -219,6 +219,73 @@ struct nand_ops {
bool (*isbad)(struct nand_device *nand, const struct nand_pos *pos);
};
+/**
+ * struct nand_ecc_context - Context for the ECC engine
+ * @conf: basic ECC engine parameters
+ * @total: total number of bytes used for storing ECC codes, this is used by
+ * generic OOB layouts
+ * @priv: ECC engine driver private data
+ */
+struct nand_ecc_context {
+ struct nand_ecc_props conf;
+ unsigned int total;
+ void *priv;
+};
+
+/**
+ * struct nand_ecc_engine_ops - ECC engine operations
+ * @init_ctx: given a desired user configuration for the pointed NAND device,
+ * requests the ECC engine driver to setup a configuration with
+ * values it supports.
+ * @cleanup_ctx: clean the context initialized by @init_ctx.
+ * @prepare_io_req: is called before reading/writing a page to prepare the I/O
+ * request to be performed with ECC correction.
+ * @finish_io_req: is called after reading/writing a page to terminate the I/O
+ * request and ensure proper ECC correction.
+ */
+struct nand_ecc_engine_ops {
+ int (*init_ctx)(struct nand_device *nand);
+ void (*cleanup_ctx)(struct nand_device *nand);
+ int (*prepare_io_req)(struct nand_device *nand,
+ struct nand_page_io_req *req);
+ int (*finish_io_req)(struct nand_device *nand,
+ struct nand_page_io_req *req);
+};
+
+/**
+ * struct nand_ecc_engine - ECC engine abstraction for NAND devices
+ * @ops: ECC engine operations
+ */
+struct nand_ecc_engine {
+ struct nand_ecc_engine_ops *ops;
+};
+
+int nand_ecc_init_ctx(struct nand_device *nand);
+void nand_ecc_cleanup_ctx(struct nand_device *nand);
+int nand_ecc_prepare_io_req(struct nand_device *nand,
+ struct nand_page_io_req *req);
+int nand_ecc_finish_io_req(struct nand_device *nand,
+ struct nand_page_io_req *req);
+
+/**
+ * struct nand_ecc - Information relative to the ECC
+ * @defaults: Default values, depend on the underlying subsystem
+ * @requirements: ECC requirements from the NAND chip perspective
+ * @user_conf: User desires in terms of ECC parameters
+ * @ctx: ECC context for the ECC engine, derived from the device @requirements
+ * the @user_conf and the @defaults
+ * @ondie_engine: On-die ECC engine reference, if any
+ * @engine: ECC engine actually bound
+ */
+struct nand_ecc {
+ struct nand_ecc_props defaults;
+ struct nand_ecc_props requirements;
+ struct nand_ecc_props user_conf;
+ struct nand_ecc_context ctx;
+ struct nand_ecc_engine *ondie_engine;
+ struct nand_ecc_engine *engine;
+};
+
/**
* struct nand_device - NAND device
* @mtd: MTD instance attached to the NAND device
Create a generic ECC engine object. Later the ecc.c file will receive more generic code coming from the raw NAND specific part. This is a base to instantiate ECC engine objects. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> --- drivers/mtd/nand/Kconfig | 8 ++ drivers/mtd/nand/Makefile | 2 + drivers/mtd/nand/ecc.c | 157 ++++++++++++++++++++++++++++++++++++++ include/linux/mtd/nand.h | 67 ++++++++++++++++ 4 files changed, 234 insertions(+) create mode 100644 drivers/mtd/nand/ecc.c