@@ -15,7 +15,7 @@ Optional properties:
the transceiver is actually CTS_B, not RTS_B. CTS_B is always output,
and RTS_B is input, regardless of dte-mode.
-Please check Documentation/devicetree/bindings/serial/serial.txt
+Please check Documentation/devicetree/bindings/serial/serial.yaml
for the complete list of generic properties.
Note: Each uart controller should have an alias correctly numbered
@@ -128,9 +128,9 @@ Optional properties:
transmission, and one for reception.
- dma-names: Must contain a list of two DMA names, "tx" and "rx".
- {cts,dsr,dcd,rng,rts,dtr}-gpios: Specify GPIOs for modem lines, cfr. the
- generic serial DT bindings in serial.txt.
+ generic serial DT bindings in serial.yaml.
- uart-has-rtscts: Indicates dedicated lines for RTS/CTS hardware flow
- control, cfr. the generic serial DT bindings in serial.txt.
+ control, cfr. the generic serial DT bindings in serial.yaml.
Example:
aliases {
deleted file mode 100644
@@ -1,56 +0,0 @@
-Generic Serial DT Bindings
-
-This document lists a set of generic properties for describing UARTs in a
-device tree. Whether these properties apply to a particular device depends on
-the DT bindings for the actual device.
-
-Optional properties:
- - cts-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be
- used as the UART's CTS line.
- - dcd-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be
- used as the UART's DCD line.
- - dsr-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be
- used as the UART's DSR line.
- - dtr-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be
- used as the UART's DTR line.
- - rng-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be
- used as the UART's RNG line.
- - rts-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be
- used as the UART's RTS line.
-
- - uart-has-rtscts: The presence of this property indicates that the
- UART has dedicated lines for RTS/CTS hardware flow control, and that
- they are available for use (wired and enabled by pinmux configuration).
- This depends on both the UART hardware and the board wiring.
- Note that this property is mutually-exclusive with "cts-gpios" and
- "rts-gpios" above, unless support is provided to switch between modes
- dynamically.
-
-
-Examples:
-
- uart1: serial@48022000 {
- compatible = "ti,am3352-uart", "ti,omap3-uart";
- ti,hwmods = "uart2";
- clock-frequency = <48000000>;
- reg = <0x48022000 0x2000>;
- interrupts = <73>;
- dmas = <&edma 28 0>, <&edma 29 0>;
- dma-names = "tx", "rx";
- dtr-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;
- dsr-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
- dcd-gpios = <&gpio2 24 GPIO_ACTIVE_LOW>;
- rng-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>;
- cts-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
- rts-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
- };
-
- scifa4: serial@e6c80000 {
- compatible = "renesas,scifa-sh73a0", "renesas,scifa";
- reg = <0xe6c80000 0x100>;
- interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&mstp2_clks SH73A0_CLK_SCIFA4>;
- clock-names = "fck";
- power-domains = <&pd_a3sp>;
- uart-has-rtscts;
- };
new file mode 100644
@@ -0,0 +1,71 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/serial/serial.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Serial Interface Generic DT Bindings
+
+maintainers:
+ - Greg Kroah-Hartman <gregkh@linuxfoundation.org>
+
+description:
+ This document lists a set of generic properties for describing UARTs in a
+ device tree. Whether these properties apply to a particular device depends
+ on the DT bindings for the actual device.
+
+properties:
+ $nodename:
+ pattern: "^serial(@.*)?$"
+
+ cts-gpios:
+ maxItems: 1
+ description:
+ Must contain a GPIO specifier, referring to the GPIO pin to be used as
+ the UART's CTS line.
+
+ dcd-gpios:
+ maxItems: 1
+ description:
+ Must contain a GPIO specifier, referring to the GPIO pin to be used as
+ the UART's DCD line.
+
+ dsr-gpios:
+ maxItems: 1
+ description:
+ Must contain a GPIO specifier, referring to the GPIO pin to be used as
+ the UART's DSR line.
+
+ dtr-gpios:
+ maxItems: 1
+ description:
+ Must contain a GPIO specifier, referring to the GPIO pin to be used as
+ the UART's DTR line.
+
+ rng-gpios:
+ maxItems: 1
+ description:
+ Must contain a GPIO specifier, referring to the GPIO pin to be used as
+ the UART's RNG line.
+
+ rts-gpios:
+ maxItems: 1
+ description:
+ Must contain a GPIO specifier, referring to the GPIO pin to be used as
+ the UART's RTS line.
+
+ uart-has-rtscts:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ The presence of this property indicates that the UART has dedicated lines
+ for RTS/CTS hardware flow control, and that they are available for use
+ (wired and enabled by pinmux configuration). This depends on both the
+ UART hardware and the board wiring.
+
+if:
+ required:
+ - uart-has-rtscts
+then:
+ properties:
+ cts-gpios: false
+ rts-gpios: false
Convert the generic serial interface Device Tree binding documentation to json-schema. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> --- v2: - Update references to serial.txt, - Fix nodename pattern, - Add missing maxItems to *-gpios, - Express that uart-has-rtscts and [cr]ts-gpios are mutually-exclusive, - Drop examples. --- .../bindings/serial/fsl-imx-uart.txt | 2 +- .../bindings/serial/renesas,sci-serial.txt | 4 +- .../devicetree/bindings/serial/serial.txt | 56 --------------- .../devicetree/bindings/serial/serial.yaml | 71 +++++++++++++++++++ 4 files changed, 74 insertions(+), 59 deletions(-) delete mode 100644 Documentation/devicetree/bindings/serial/serial.txt create mode 100644 Documentation/devicetree/bindings/serial/serial.yaml