@@ -355,15 +355,25 @@ int rtl8366_vlan_prepare(struct dsa_switch *ds, int port,
const struct switchdev_obj_port_vlan *vlan)
{
struct realtek_smi *smi = ds->priv;
+ u16 vid_begin = vlan->vid_begin;
+ u16 vid_end = vlan->vid_end;
u16 vid;
int ret;
- for (vid = vlan->vid_begin; vid < vlan->vid_end; vid++)
+ if (vid_begin == 0) {
+ dev_info(smi->dev, "prepare VLAN 0 - ignored\n");
+ if (vid_end == 0)
+ return 0;
+ /* Skip VLAN 0 and start with VLAN 1 */
+ vid_begin = 1;
+ }
+
+ for (vid = vid_begin; vid < vid_end; vid++)
if (!smi->ops->is_vlan_valid(smi, vid))
return -EINVAL;
dev_info(smi->dev, "prepare VLANs %04x..%04x\n",
- vlan->vid_begin, vlan->vid_end);
+ vid_begin, vid_end);
/* Enable VLAN in the hardware
* FIXME: what's with this 4k business?
@@ -383,27 +393,46 @@ void rtl8366_vlan_add(struct dsa_switch *ds, int port,
bool untagged = !!(vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED);
bool pvid = !!(vlan->flags & BRIDGE_VLAN_INFO_PVID);
struct realtek_smi *smi = ds->priv;
+ u16 vid_begin = vlan->vid_begin;
+ u16 vid_end = vlan->vid_end;
u32 member = 0;
u32 untag = 0;
u16 vid;
int ret;
- for (vid = vlan->vid_begin; vid < vlan->vid_end; vid++)
- if (!smi->ops->is_vlan_valid(smi, vid))
+ if (vid_begin == 0) {
+ dev_info(smi->dev, "set VLAN 0 on port %d = default VLAN\n",
+ port);
+ /* Set up default tagging */
+ ret = rtl8366_set_default_vlan_and_pvid(smi, port);
+ if (ret) {
+ dev_err(smi->dev,
+ "error setting default VLAN on port %d\n",
+ port);
return;
+ }
+ if (vid_end == 0)
+ return;
+ /* Skip VLAN 0 and start with VLAN 1 */
+ vid_begin = 1;
+ }
- dev_info(smi->dev, "add VLAN on port %d, %s, %s\n",
- port,
- untagged ? "untagged" : "tagged",
- pvid ? " PVID" : "no PVID");
+ for (vid = vid_begin; vid < vid_end; vid++)
+ if (!smi->ops->is_vlan_valid(smi, vid))
+ return;
if (dsa_is_dsa_port(ds, port) || dsa_is_cpu_port(ds, port))
dev_err(smi->dev, "port is DSA or CPU port\n");
- for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) {
+ for (vid = vid_begin; vid <= vid_end; ++vid) {
int pvid_val = 0;
- dev_info(smi->dev, "add VLAN %04x\n", vid);
+ dev_info(smi->dev, "add VLAN %04x to port %d, %s, %s\n",
+ vid,
+ port,
+ untagged ? "untagged" : "tagged",
+ pvid ? " PVID" : "no PVID");
+
member |= BIT(port);
if (untagged)
@@ -437,15 +466,25 @@ int rtl8366_vlan_del(struct dsa_switch *ds, int port,
const struct switchdev_obj_port_vlan *vlan)
{
struct realtek_smi *smi = ds->priv;
+ u16 vid_begin = vlan->vid_begin;
+ u16 vid_end = vlan->vid_end;
u16 vid;
int ret;
- dev_info(smi->dev, "del VLAN on port %d\n", port);
+ if (vid_begin == 0) {
+ dev_info(smi->dev, "remove port %d from VLAN 0 (no-op)\n",
+ port);
+ if (vid_end == 0)
+ return 0;
+ /* Skip VLAN 0 and start with VLAN 1 */
+ vid_begin = 1;
+ }
- for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) {
+ for (vid = vid_begin; vid <= vid_end; ++vid) {
int i;
- dev_info(smi->dev, "del VLAN %04x\n", vid);
+ dev_info(smi->dev, "remove VLAN %04x from port %d\n",
+ vid, port);
for (i = 0; i < smi->num_vlan_mc; i++) {
struct rtl8366_vlan_mc vlanmc;
The code in net/8021q/vlan.c, vlan_device_event() sets VLAN 0 for a VLAN-capable ethernet device when it comes up. Since the RTL8366 DSA switches must have a VLAN and PVID set up for any packets to come through we have already set up default VLAN for each port as part of bringing the switch online. Make sure that setting VLAN 0 has the same effect and does not try to actually tell the hardware to use VLAN 0 on the port because that will not work. Cc: DENG Qingfang <dqfext@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- drivers/net/dsa/rtl8366.c | 65 +++++++++++++++++++++++++++++++-------- 1 file changed, 52 insertions(+), 13 deletions(-)