@@ -70,6 +70,7 @@ config NET_DSA_QCA8K
config NET_DSA_REALTEK_SMI
tristate "Realtek SMI Ethernet switch family support"
depends on NET_DSA
+ select NET_DSA_TAG_RTL4_A
select FIXED_PHY
select IRQ_DOMAIN
select REALTEK_PHY
@@ -109,8 +109,8 @@
/* CPU port control reg */
#define RTL8368RB_CPU_CTRL_REG 0x0061
#define RTL8368RB_CPU_PORTS_MSK 0x00FF
-/* Enables inserting custom tag length/type 0x8899 */
-#define RTL8368RB_CPU_INSTAG BIT(15)
+/* Disables inserting custom tag length/type 0x8899 */
+#define RTL8368RB_CPU_NO_TAG BIT(15)
#define RTL8366RB_SMAR0 0x0070 /* bits 0..15 */
#define RTL8366RB_SMAR1 0x0071 /* bits 16..31 */
@@ -844,16 +844,14 @@ static int rtl8366rb_setup(struct dsa_switch *ds)
if (ret)
return ret;
- /* Enable CPU port and enable inserting CPU tag
+ /* Enable CPU port with custom DSA tag 8899.
*
- * Disabling RTL8368RB_CPU_INSTAG here will change the behaviour
- * of the switch totally and it will start talking Realtek RRCP
- * internally. It is probably possible to experiment with this,
- * but then the kernel needs to understand and handle RRCP first.
+ * If you set RTL8368RB_CPU_NO_TAG (bit 15) in this registers
+ * the custom tag is turned off.
*/
ret = regmap_update_bits(smi->map, RTL8368RB_CPU_CTRL_REG,
0xFFFF,
- RTL8368RB_CPU_INSTAG | BIT(smi->cpu_port));
+ BIT(smi->cpu_port));
if (ret)
return ret;
@@ -967,21 +965,8 @@ static enum dsa_tag_protocol rtl8366_get_tag_protocol(struct dsa_switch *ds,
int port,
enum dsa_tag_protocol mp)
{
- /* For now, the RTL switches are handled without any custom tags.
- *
- * It is possible to turn on "custom tags" by removing the
- * RTL8368RB_CPU_INSTAG flag when enabling the port but what it
- * does is unfamiliar to DSA: ethernet frames of type 8899, the Realtek
- * Remote Control Protocol (RRCP) start to appear on the CPU port of
- * the device. So this is not the ordinary few extra bytes in the
- * frame. Instead it appears that the switch starts to talk Realtek
- * RRCP internally which means a pretty complex RRCP implementation
- * decoding and responding the RRCP protocol is needed to exploit this.
- *
- * The OpenRRCP project (dormant since 2009) have reverse-egineered
- * parts of the protocol.
- */
- return DSA_TAG_PROTO_NONE;
+ /* This switch uses the 4 byte protocol A Realtek DSA tag */
+ return DSA_TAG_PROTO_RTL4_A;
}
static void rtl8366rb_adjust_link(struct dsa_switch *ds, int port,
This activates the support to use the CPU tag to properly direct ingress traffic to the right port. After this e.g. ping works out-of-the-box with the RTL8366RB. Cc: DENG Qingfang <dqfext@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- drivers/net/dsa/Kconfig | 1 + drivers/net/dsa/rtl8366rb.c | 31 ++++++++----------------------- 2 files changed, 9 insertions(+), 23 deletions(-)