@@ -111,22 +111,6 @@ enum i2c_freq_mode {
};
/**
- * struct nmk_i2c_controller - client specific controller configuration
- * @clk_freq: clock frequency for the operation mode
- * @tft: Tx FIFO Threshold in bytes
- * @rft: Rx FIFO Threshold in bytes
- * @timeout Slave response timeout(ms)
- * @sm: speed mode
- */
-struct nmk_i2c_controller {
- u32 clk_freq;
- unsigned char tft;
- unsigned char rft;
- int timeout;
- enum i2c_freq_mode sm;
-};
-
-/**
* struct i2c_vendor_data - per-vendor variations
* @has_mtdws: variant has the MTDWS bit
* @fifodepth: variant FIFO depth
@@ -174,8 +158,12 @@ struct i2c_nmk_client {
* @irq: interrupt line for the controller.
* @virtbase: virtual io memory area.
* @clk: hardware i2c block clock.
- * @cfg: machine provided controller configuration.
* @cli: holder of client specific data.
+ * @clk_freq: clock frequency for the operation mode
+ * @tft: Tx FIFO Threshold in bytes
+ * @rft: Rx FIFO Threshold in bytes
+ * @timeout Slave response timeout (ms)
+ * @sm: speed mode
* @stop: stop condition.
* @xfer_complete: acknowledge completion for a I2C message.
* @result: controller propogated result.
@@ -188,8 +176,12 @@ struct nmk_i2c_dev {
int irq;
void __iomem *virtbase;
struct clk *clk;
- struct nmk_i2c_controller cfg;
struct i2c_nmk_client cli;
+ u32 clk_freq;
+ unsigned char tft;
+ unsigned char rft;
+ int timeout;
+ enum i2c_freq_mode sm;
int stop;
struct completion xfer_complete;
int result;
@@ -386,7 +378,7 @@ static void setup_i2c_controller(struct nmk_i2c_dev *dev)
* slsu = cycles / (1000000000 / f) + 1
*/
ns = DIV_ROUND_UP_ULL(1000000000ULL, i2c_clk);
- switch (dev->cfg.sm) {
+ switch (dev->sm) {
case I2C_FREQ_MODE_FAST:
case I2C_FREQ_MODE_FAST_PLUS:
slsu = DIV_ROUND_UP(100, ns); /* Fast */
@@ -409,7 +401,7 @@ static void setup_i2c_controller(struct nmk_i2c_dev *dev)
* 2 whereas it is 3 for fast and fastplus mode of
* operation. TODO - high speed support.
*/
- div = (dev->cfg.clk_freq > 100000) ? 3 : 2;
+ div = (dev->clk_freq > 100000) ? 3 : 2;
/*
* generate the mask for baud rate counters. The controller
@@ -419,7 +411,7 @@ static void setup_i2c_controller(struct nmk_i2c_dev *dev)
* so set brcr1 to 0.
*/
brcr1 = 0 << 16;
- brcr2 = (i2c_clk/(dev->cfg.clk_freq * div)) & 0xffff;
+ brcr2 = (i2c_clk/(dev->clk_freq * div)) & 0xffff;
/* set the baud rate counter register */
writel((brcr1 | brcr2), dev->virtbase + I2C_BRCR);
@@ -430,7 +422,7 @@ static void setup_i2c_controller(struct nmk_i2c_dev *dev)
* TODO - support for fast mode plus (up to 1Mb/s)
* and high speed (up to 3.4 Mb/s)
*/
- if (dev->cfg.sm > I2C_FREQ_MODE_FAST) {
+ if (dev->sm > I2C_FREQ_MODE_FAST) {
dev_err(&dev->adev->dev,
"do not support this mode defaulting to std. mode\n");
brcr2 = i2c_clk/(100000 * 2) & 0xffff;
@@ -438,11 +430,11 @@ static void setup_i2c_controller(struct nmk_i2c_dev *dev)
writel(I2C_FREQ_MODE_STANDARD << 4,
dev->virtbase + I2C_CR);
}
- writel(dev->cfg.sm << 4, dev->virtbase + I2C_CR);
+ writel(dev->sm << 4, dev->virtbase + I2C_CR);
/* set the Tx and Rx FIFO threshold */
- writel(dev->cfg.tft, dev->virtbase + I2C_TFTR);
- writel(dev->cfg.rft, dev->virtbase + I2C_RFTR);
+ writel(dev->tft, dev->virtbase + I2C_TFTR);
+ writel(dev->rft, dev->virtbase + I2C_RFTR);
}
/**
@@ -958,63 +950,32 @@ static const struct i2c_algorithm nmk_i2c_algo = {
.functionality = nmk_i2c_functionality
};
-static struct nmk_i2c_controller u8500_i2c = {
- .tft = 1, /* Tx FIFO threshold */
- .rft = 8, /* Rx FIFO threshold */
- .clk_freq = 400000, /* fast mode operation */
- .timeout = 200, /* Slave response timeout(ms) */
- .sm = I2C_FREQ_MODE_FAST,
-};
-
static void nmk_i2c_of_probe(struct device_node *np,
- struct nmk_i2c_controller *pdata)
+ struct nmk_i2c_dev *nmk)
{
- of_property_read_u32(np, "clock-frequency", &pdata->clk_freq);
+ /* Default to 400 kHz if no frequency is given in the node */
+ if (of_property_read_u32(np, "clock-frequency", &nmk->clk_freq))
+ nmk->clk_freq = 400000;
/* This driver only supports 'standard' and 'fast' modes of operation. */
- if (pdata->clk_freq <= 100000)
- pdata->sm = I2C_FREQ_MODE_STANDARD;
+ if (nmk->clk_freq <= 100000)
+ nmk->sm = I2C_FREQ_MODE_STANDARD;
else
- pdata->sm = I2C_FREQ_MODE_FAST;
+ nmk->sm = I2C_FREQ_MODE_FAST;
+ nmk->tft = 1; /* Tx FIFO threshold */
+ nmk->rft = 8; /* Rx FIFO threshold */
+ nmk->timeout = 200; /* Slave response timeout(ms) */
}
static int nmk_i2c_probe(struct amba_device *adev, const struct amba_id *id)
{
int ret = 0;
- struct nmk_i2c_controller *pdata = dev_get_platdata(&adev->dev);
struct device_node *np = adev->dev.of_node;
struct nmk_i2c_dev *dev;
struct i2c_adapter *adap;
struct i2c_vendor_data *vendor = id->data;
u32 max_fifo_threshold = (vendor->fifodepth / 2) - 1;
- if (!pdata) {
- if (np) {
- pdata = devm_kzalloc(&adev->dev, sizeof(*pdata), GFP_KERNEL);
- if (!pdata) {
- ret = -ENOMEM;
- goto err_no_mem;
- }
- /* Provide the default configuration as a base. */
- memcpy(pdata, &u8500_i2c, sizeof(struct nmk_i2c_controller));
- nmk_i2c_of_probe(np, pdata);
- } else
- /* No i2c configuration found, using the default. */
- pdata = &u8500_i2c;
- }
-
- if (pdata->tft > max_fifo_threshold) {
- dev_warn(&adev->dev, "requested TX FIFO threshold %u, adjusted down to %u\n",
- pdata->tft, max_fifo_threshold);
- pdata->tft = max_fifo_threshold;
- }
-
- if (pdata->rft > max_fifo_threshold) {
- dev_warn(&adev->dev, "requested RX FIFO threshold %u, adjusted down to %u\n",
- pdata->rft, max_fifo_threshold);
- pdata->rft = max_fifo_threshold;
- }
-
dev = kzalloc(sizeof(struct nmk_i2c_dev), GFP_KERNEL);
if (!dev) {
dev_err(&adev->dev, "cannot allocate memory\n");
@@ -1024,6 +985,20 @@ static int nmk_i2c_probe(struct amba_device *adev, const struct amba_id *id)
dev->vendor = vendor;
dev->busy = false;
dev->adev = adev;
+ nmk_i2c_of_probe(np, dev);
+
+ if (dev->tft > max_fifo_threshold) {
+ dev_warn(&adev->dev, "requested TX FIFO threshold %u, adjusted down to %u\n",
+ dev->tft, max_fifo_threshold);
+ dev->tft = max_fifo_threshold;
+ }
+
+ if (dev->rft > max_fifo_threshold) {
+ dev_warn(&adev->dev, "requested RX FIFO threshold %u, adjusted down to %u\n",
+ dev->rft, max_fifo_threshold);
+ dev->rft = max_fifo_threshold;
+ }
+
amba_set_drvdata(adev, dev);
/* Select default pin state */
@@ -1060,16 +1035,10 @@ static int nmk_i2c_probe(struct amba_device *adev, const struct amba_id *id)
adap->owner = THIS_MODULE;
adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
adap->algo = &nmk_i2c_algo;
- adap->timeout = msecs_to_jiffies(pdata->timeout);
+ adap->timeout = msecs_to_jiffies(dev->timeout);
snprintf(adap->name, sizeof(adap->name),
"Nomadik I2C at %pR", &adev->res);
- /* fetch the controller configuration from machine */
- dev->cfg.clk_freq = pdata->clk_freq;
- dev->cfg.tft = pdata->tft;
- dev->cfg.rft = pdata->rft;
- dev->cfg.sm = pdata->sm;
-
i2c_set_adapdata(adap, dev);
dev_info(&adev->dev,
Move the former platform data struct nmk_i2c_controller into the per-device state container struct i2c_nmk_client, and remove all the platform data probe path hacks. Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- ChangeLog v1->v2: - Drop pointless check for np, as the device can only probe from the device tree now. --- drivers/i2c/busses/i2c-nomadik.c | 115 ++++++++++++++------------------------- 1 file changed, 42 insertions(+), 73 deletions(-)