@@ -49,7 +49,8 @@ usb2phy@4a0ad080 {
TI PIPE3 PHY
Required properties:
- - compatible: Should be "ti,phy-usb3". "ti,omap-usb3" is deprecated.
+ - compatible: Should be "ti,phy-usb3" or "ti,phy-pipe3-sata".
+ "ti,omap-usb3" is deprecated.
- reg : Address and length of the register set for the device.
- reg-names: The names of the register addresses corresponding to the registers
filled in "reg".
@@ -66,6 +66,11 @@ struct pipe3_dpll_params {
u32 mf;
};
+struct pipe3_dpll_map {
+ unsigned long rate;
+ struct pipe3_dpll_params params;
+};
+
struct ti_pipe3 {
void __iomem *pll_ctrl_base;
struct device *dev;
@@ -73,20 +78,27 @@ struct ti_pipe3 {
struct clk *wkupclk;
struct clk *sys_clk;
struct clk *optclk;
+ struct pipe3_dpll_map *dpll_map;
};
-struct pipe3_dpll_map {
- unsigned long rate;
- struct pipe3_dpll_params params;
-};
-
-static struct pipe3_dpll_map dpll_map[] = {
+static struct pipe3_dpll_map dpll_map_usb[] = {
{12000000, {1250, 5, 4, 20, 0} }, /* 12 MHz */
{16800000, {3125, 20, 4, 20, 0} }, /* 16.8 MHz */
{19200000, {1172, 8, 4, 20, 65537} }, /* 19.2 MHz */
{20000000, {1000, 7, 4, 10, 0} }, /* 20 MHz */
{26000000, {1250, 12, 4, 20, 0} }, /* 26 MHz */
{38400000, {3125, 47, 4, 20, 92843} }, /* 38.4 MHz */
+ { }, /* Terminator */
+};
+
+static struct pipe3_dpll_map dpll_map_sata[] = {
+ {12000000, {1000, 7, 4, 6, 0} }, /* 12 MHz */
+ {16800000, {714, 7, 4, 6, 0} }, /* 16.8 MHz */
+ {19200000, {625, 7, 4, 6, 0} }, /* 19.2 MHz */
+ {20000000, {600, 7, 4, 6, 0} }, /* 20 MHz */
+ {26000000, {461, 7, 4, 6, 0} }, /* 26 MHz */
+ {38400000, {312, 7, 4, 6, 0} }, /* 38.4 MHz */
+ { }, /* Terminator */
};
static inline u32 ti_pipe3_readl(void __iomem *addr, unsigned offset)
@@ -100,15 +112,20 @@ static inline void ti_pipe3_writel(void __iomem *addr, unsigned offset,
__raw_writel(data, addr + offset);
}
-static struct pipe3_dpll_params *ti_pipe3_get_dpll_params(unsigned long rate)
+static struct pipe3_dpll_params *ti_pipe3_get_dpll_params(struct ti_pipe3 *phy)
{
- int i;
+ unsigned long rate;
+ struct pipe3_dpll_map *dpll_map = phy->dpll_map;
- for (i = 0; i < ARRAY_SIZE(dpll_map); i++) {
- if (rate == dpll_map[i].rate)
- return &dpll_map[i].params;
+ rate = clk_get_rate(phy->sys_clk);
+
+ for (; dpll_map->rate; dpll_map++) {
+ if (rate == dpll_map->rate)
+ return &dpll_map->params;
}
+ dev_err(phy->dev, "No DPLL configuration for %lu Hz SYS CLK\n", rate);
+
return NULL;
}
@@ -182,16 +199,11 @@ static void ti_pipe3_dpll_relock(struct ti_pipe3 *phy)
static int ti_pipe3_dpll_lock(struct ti_pipe3 *phy)
{
u32 val;
- unsigned long rate;
struct pipe3_dpll_params *dpll_params;
- rate = clk_get_rate(phy->sys_clk);
- dpll_params = ti_pipe3_get_dpll_params(rate);
- if (!dpll_params) {
- dev_err(phy->dev,
- "No DPLL configuration for %lu Hz SYS CLK\n", rate);
+ dpll_params = ti_pipe3_get_dpll_params(phy);
+ if (!dpll_params)
return -EINVAL;
- }
val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION1);
val &= ~PLL_REGN_MASK;
@@ -244,6 +256,10 @@ static struct phy_ops ops = {
.owner = THIS_MODULE,
};
+#ifdef CONFIG_OF
+static const struct of_device_id ti_pipe3_id_table[];
+#endif
+
static int ti_pipe3_probe(struct platform_device *pdev)
{
struct ti_pipe3 *phy;
@@ -253,8 +269,10 @@ static int ti_pipe3_probe(struct platform_device *pdev)
struct device_node *node = pdev->dev.of_node;
struct device_node *control_node;
struct platform_device *control_pdev;
+ const struct of_device_id *match;
- if (!node)
+ match = of_match_device(of_match_ptr(ti_pipe3_id_table), &pdev->dev);
+ if (!match)
return -EINVAL;
phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL);
@@ -263,6 +281,12 @@ static int ti_pipe3_probe(struct platform_device *pdev)
return -ENOMEM;
}
+ phy->dpll_map = (struct pipe3_dpll_map *)match->data;
+ if (!phy->dpll_map) {
+ dev_err(&pdev->dev, "no DPLL data\n");
+ return -EINVAL;
+ }
+
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pll_ctrl");
phy->pll_ctrl_base = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(phy->pll_ctrl_base))
@@ -384,8 +408,18 @@ static const struct dev_pm_ops ti_pipe3_pm_ops = {
#ifdef CONFIG_OF
static const struct of_device_id ti_pipe3_id_table[] = {
- { .compatible = "ti,phy-usb3" },
- { .compatible = "ti,omap-usb3" },
+ {
+ .compatible = "ti,phy-usb3",
+ .data = dpll_map_usb,
+ },
+ {
+ .compatible = "ti,omap-usb3",
+ .data = dpll_map_usb,
+ },
+ {
+ .compatible = "ti,phy-pipe3-sata",
+ .data = dpll_map_sata,
+ },
{}
};
MODULE_DEVICE_TABLE(of, ti_pipe3_id_table);
USB and SATA DPLLs need different settings. Provide the SATA DPLL settings and use the proper DPLL settings based on device tree node's compatible_id. Update the DT binding information. Signed-off-by: Roger Quadros <rogerq@ti.com> --- Documentation/devicetree/bindings/phy/ti-phy.txt | 3 +- drivers/phy/phy-ti-pipe3.c | 76 +++++++++++++++++------- 2 files changed, 57 insertions(+), 22 deletions(-)