new file mode 100644
@@ -0,0 +1,261 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/renesas,etheravb.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas Ethernet AVB
+
+maintainers:
+ - Sergei Shtylyov <sergei.shtylyov@gmail.com>
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - enum:
+ - renesas,etheravb-r8a7742 # RZ/G1H
+ - renesas,etheravb-r8a7743 # RZ/G1M
+ - renesas,etheravb-r8a7744 # RZ/G1N
+ - renesas,etheravb-r8a7745 # RZ/G1E
+ - renesas,etheravb-r8a77470 # RZ/G1C
+ - renesas,etheravb-r8a7790 # R-Car H2
+ - renesas,etheravb-r8a7791 # R-Car M2-W
+ - renesas,etheravb-r8a7792 # R-Car V2H
+ - renesas,etheravb-r8a7793 # R-Car M2-N
+ - renesas,etheravb-r8a7794 # R-Car E2
+ - const: renesas,etheravb-rcar-gen2 # R-Car Gen2 and RZ/G1
+
+ - items:
+ - enum:
+ - renesas,etheravb-r8a774a1 # RZ/G2M
+ - renesas,etheravb-r8a774b1 # RZ/G2N
+ - renesas,etheravb-r8a774c0 # RZ/G2E
+ - renesas,etheravb-r8a7795 # R-Car H3
+ - renesas,etheravb-r8a7796 # R-Car M3-W
+ - renesas,etheravb-r8a77961 # R-Car M3-W+
+ - renesas,etheravb-r8a77965 # R-Car M3-N
+ - renesas,etheravb-r8a77970 # R-Car V3M
+ - renesas,etheravb-r8a77980 # R-Car V3H
+ - renesas,etheravb-r8a77990 # R-Car E3
+ - renesas,etheravb-r8a77995 # R-Car D3
+ - const: renesas,etheravb-rcar-gen3 # R-Car Gen3 and RZ/G2
+
+ reg: true
+
+ interrupts: true
+
+ interrupt-names: true
+
+ clocks:
+ maxItems: 1
+
+ iommus:
+ maxItems: 1
+
+ power-domains:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ phy-mode: true
+
+ phy-handle: true
+
+ '#address-cells':
+ description: Number of address cells for the MDIO bus.
+ const: 1
+
+ '#size-cells':
+ description: Number of size cells on the MDIO bus.
+ const: 0
+
+ renesas,no-ether-link:
+ type: boolean
+ description:
+ Specify when a board does not provide a proper AVB_LINK signal.
+
+ renesas,ether-link-active-low:
+ type: boolean
+ description:
+ Specify when the AVB_LINK signal is active-low instead of normal
+ active-high.
+
+ rx-internal-delay-ps:
+ enum: [0, 1800]
+
+ tx-internal-delay-ps:
+ enum: [0, 2000]
+
+patternProperties:
+ "^ethernet-phy@[0-9a-f]$":
+ type: object
+ $ref: ethernet-phy.yaml#
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - power-domains
+ - resets
+ - phy-mode
+ - phy-handle
+ - '#address-cells'
+ - '#size-cells'
+
+allOf:
+ - $ref: ethernet-controller.yaml#
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - renesas,etheravb-rcar-gen2
+ - renesas,etheravb-r8a7795
+ - renesas,etheravb-r8a7796
+ - renesas,etheravb-r8a77961
+ - renesas,etheravb-r8a77965
+ then:
+ properties:
+ reg:
+ items:
+ - description: MAC register block
+ - description: Stream buffer
+ else:
+ properties:
+ reg:
+ items:
+ - description: MAC register block
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: renesas,etheravb-rcar-gen2
+ then:
+ properties:
+ interrupts:
+ maxItems: 1
+ interrupt-names:
+ items:
+ - const: mux
+ rx-internal-delay-ps: false
+ else:
+ properties:
+ interrupts:
+ minItems: 25
+ maxItems: 25
+ interrupt-names:
+ items:
+ pattern: '^ch[0-9]+$'
+ required:
+ - interrupt-names
+ - rx-internal-delay-ps
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - renesas,etheravb-r8a774a1
+ - renesas,etheravb-r8a774b1
+ - renesas,etheravb-r8a7795
+ - renesas,etheravb-r8a7796
+ - renesas,etheravb-r8a77961
+ - renesas,etheravb-r8a77965
+ - renesas,etheravb-r8a77970
+ - renesas,etheravb-r8a77980
+ then:
+ required:
+ - tx-internal-delay-ps
+ else:
+ properties:
+ tx-internal-delay-ps: false
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: renesas,etheravb-r8a77995
+ then:
+ properties:
+ rx-internal-delay-ps:
+ const: 1800
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: renesas,etheravb-r8a77980
+ then:
+ properties:
+ tx-internal-delay-ps:
+ const: 2000
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/r8a7795-cpg-mssr.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/power/r8a7795-sysc.h>
+ #include <dt-bindings/gpio/gpio.h>
+ aliases {
+ ethernet0 = &avb;
+ };
+
+ avb: ethernet@e6800000 {
+ compatible = "renesas,etheravb-r8a7795",
+ "renesas,etheravb-rcar-gen3";
+ reg = <0xe6800000 0x800>, <0xe6a00000 0x10000>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "ch0", "ch1", "ch2", "ch3", "ch4", "ch5", "ch6",
+ "ch7", "ch8", "ch9", "ch10", "ch11", "ch12",
+ "ch13", "ch14", "ch15", "ch16", "ch17", "ch18",
+ "ch19", "ch20", "ch21", "ch22", "ch23", "ch24";
+ clocks = <&cpg CPG_MOD 812>;
+ iommus = <&ipmmu_ds0 16>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+ resets = <&cpg 812>;
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+ rx-internal-delay-ps = <0>;
+ tx-internal-delay-ps = <2000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@0 {
+ rxc-skew-ps = <1500>;
+ reg = <0>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
+ };
+ };
deleted file mode 100644
@@ -1,137 +0,0 @@
-* Renesas Electronics Ethernet AVB
-
-This file provides information on what the device node for the Ethernet AVB
-interface contains.
-
-Required properties:
-- compatible: Must contain one or more of the following:
- - "renesas,etheravb-r8a7742" for the R8A7742 SoC.
- - "renesas,etheravb-r8a7743" for the R8A7743 SoC.
- - "renesas,etheravb-r8a7744" for the R8A7744 SoC.
- - "renesas,etheravb-r8a7745" for the R8A7745 SoC.
- - "renesas,etheravb-r8a77470" for the R8A77470 SoC.
- - "renesas,etheravb-r8a7790" for the R8A7790 SoC.
- - "renesas,etheravb-r8a7791" for the R8A7791 SoC.
- - "renesas,etheravb-r8a7792" for the R8A7792 SoC.
- - "renesas,etheravb-r8a7793" for the R8A7793 SoC.
- - "renesas,etheravb-r8a7794" for the R8A7794 SoC.
- - "renesas,etheravb-rcar-gen2" as a fallback for the above
- R-Car Gen2 and RZ/G1 devices.
-
- - "renesas,etheravb-r8a774a1" for the R8A774A1 SoC.
- - "renesas,etheravb-r8a774b1" for the R8A774B1 SoC.
- - "renesas,etheravb-r8a774c0" for the R8A774C0 SoC.
- - "renesas,etheravb-r8a7795" for the R8A7795 SoC.
- - "renesas,etheravb-r8a7796" for the R8A77960 SoC.
- - "renesas,etheravb-r8a77961" for the R8A77961 SoC.
- - "renesas,etheravb-r8a77965" for the R8A77965 SoC.
- - "renesas,etheravb-r8a77970" for the R8A77970 SoC.
- - "renesas,etheravb-r8a77980" for the R8A77980 SoC.
- - "renesas,etheravb-r8a77990" for the R8A77990 SoC.
- - "renesas,etheravb-r8a77995" for the R8A77995 SoC.
- - "renesas,etheravb-rcar-gen3" as a fallback for the above
- R-Car Gen3 and RZ/G2 devices.
-
- When compatible with the generic version, nodes must list the
- SoC-specific version corresponding to the platform first followed by
- the generic version.
-
-- reg: Offset and length of (1) the register block and (2) the stream buffer.
- The region for the register block is mandatory.
- The region for the stream buffer is optional, as it is only present on
- R-Car Gen2 and RZ/G1 SoCs, and on R-Car H3 (R8A7795), M3-W (R8A77960),
- M3-W+ (R8A77961), and M3-N (R8A77965).
-- interrupts: A list of interrupt-specifiers, one for each entry in
- interrupt-names.
- If interrupt-names is not present, an interrupt specifier
- for a single muxed interrupt.
-- phy-mode: see ethernet.txt file in the same directory.
-- phy-handle: see ethernet.txt file in the same directory.
-- #address-cells: number of address cells for the MDIO bus, must be equal to 1.
-- #size-cells: number of size cells on the MDIO bus, must be equal to 0.
-- clocks: clock phandle and specifier pair.
-- pinctrl-0: phandle, referring to a default pin configuration node.
-
-Optional properties:
-- interrupt-names: A list of interrupt names.
- For the R-Car Gen 3 SoCs this property is mandatory;
- it should include one entry per channel, named "ch%u",
- where %u is the channel number ranging from 0 to 24.
- For other SoCs this property is optional; if present
- it should contain "mux" for a single muxed interrupt.
-- pinctrl-names: pin configuration state name ("default").
-- renesas,no-ether-link: boolean, specify when a board does not provide a proper
- AVB_LINK signal.
-- renesas,ether-link-active-low: boolean, specify when the AVB_LINK signal is
- active-low instead of normal active-high.
-- rx-internal-delay-ps: Internal RX clock delay.
- This property is mandatory and valid only on R-Car Gen3
- and RZ/G2 SoCs.
- Valid values are 0 and 1800.
- A non-zero value is allowed only if phy-mode = "rgmii".
- Zero is not supported on R-Car D3.
-- tx-internal-delay-ps: Internal TX clock delay.
- This property is mandatory and valid only on R-Car H3,
- M3-W, M3-W+, M3-N, V3M, and V3H, and RZ/G2M and RZ/G2N.
- Valid values are 0 and 2000.
- A non-zero value is allowed only if phy-mode = "rgmii".
- Zero is not supported on R-Car V3H.
-
-Example:
-
- ethernet@e6800000 {
- compatible = "renesas,etheravb-r8a7795", "renesas,etheravb-rcar-gen3";
- reg = <0 0xe6800000 0 0x800>, <0 0xe6a00000 0 0x10000>;
- interrupt-parent = <&gic>;
- interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "ch0", "ch1", "ch2", "ch3",
- "ch4", "ch5", "ch6", "ch7",
- "ch8", "ch9", "ch10", "ch11",
- "ch12", "ch13", "ch14", "ch15",
- "ch16", "ch17", "ch18", "ch19",
- "ch20", "ch21", "ch22", "ch23",
- "ch24";
- clocks = <&cpg CPG_MOD 812>;
- power-domains = <&cpg>;
- phy-mode = "rgmii";
- phy-handle = <&phy0>;
- rx-internal-delay-ps = <0>;
- tx-internal-delay-ps = <2000>;
-
- pinctrl-0 = <ðer_pins>;
- pinctrl-names = "default";
- renesas,no-ether-link;
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy0: ethernet-phy@0 {
- rxc-skew-ps = <1500>;
- reg = <0>;
- interrupt-parent = <&gpio2>;
- interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
- };
- };