| Message ID | 1397847510-17199-1-git-send-email-tim.kryger@linaro.org |
|---|---|
| State | New |
| Headers | show |
On 18 April 2014 20:58, Tim Kryger <tim.kryger@linaro.org> wrote: > The eMMC signalling voltage is determined by VCCQ which is provided to > the card by the host. Signalling is not required to begin at 3.3v and, > if the host and card both support a particular VCC/VCCQ combination, it > can be used immediately. > > In contrast, SD Cards must begin with 3.3v signalling and may switch to > a lower voltage signalling if instructed to do so in CMD11. A message > is required to coordinate this operation because the card only receives > a 3.3v VDD and must know when to use the 1.8v produced by its internal > regulator. > > It makes sense for the core to begin with 3.3v signalling but when that > can't be set, 1.8v and 1.2v signalling also should be attempted. This > is especially important when an external regulator with a limited range > is used to supply VCCQ to an eMMC part. > > Signed-off-by: Tim Kryger <tim.kryger@linaro.org> > --- > drivers/mmc/core/core.c | 10 +++++++++- > 1 file changed, 9 insertions(+), 1 deletion(-) > > diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c > index acbc3f2..ecdbeae 100644 > --- a/drivers/mmc/core/core.c > +++ b/drivers/mmc/core/core.c > @@ -1517,6 +1517,8 @@ void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type) > */ > void mmc_power_up(struct mmc_host *host, u32 ocr) > { > + int err; > + The variable err is not needed, since we don't plan on printing it nor returning it. Please remove and handle the return code directly in the if statements. Kind regards Ulf Hansson > if (host->ios.power_mode == MMC_POWER_ON) > return; > > @@ -1534,7 +1536,13 @@ void mmc_power_up(struct mmc_host *host, u32 ocr) > mmc_set_ios(host); > > /* Set signal voltage to 3.3V */ > - __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330); > + err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330); > + > + /* Since eMMC parts can start at 1.8v or 1.2v try those too */ > + if (err) > + err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180); > + if (err) > + __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120); > > /* > * This delay should be sufficient to allow the power supply > -- > 1.7.9.5 > -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Thu, Apr 24, 2014 at 1:38 AM, Ulf Hansson <ulf.hansson@linaro.org> wrote: > On 18 April 2014 20:58, Tim Kryger <tim.kryger@linaro.org> wrote: >> void mmc_power_up(struct mmc_host *host, u32 ocr) >> { >> + int err; >> + > > The variable err is not needed, since we don't plan on printing it nor > returning it. Please remove and handle the return code directly in the > if statements. Sure. I'll send out an updated version shortly. Thanks, Tim -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c index acbc3f2..ecdbeae 100644 --- a/drivers/mmc/core/core.c +++ b/drivers/mmc/core/core.c @@ -1517,6 +1517,8 @@ void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type) */ void mmc_power_up(struct mmc_host *host, u32 ocr) { + int err; + if (host->ios.power_mode == MMC_POWER_ON) return; @@ -1534,7 +1536,13 @@ void mmc_power_up(struct mmc_host *host, u32 ocr) mmc_set_ios(host); /* Set signal voltage to 3.3V */ - __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330); + err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330); + + /* Since eMMC parts can start at 1.8v or 1.2v try those too */ + if (err) + err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180); + if (err) + __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120); /* * This delay should be sufficient to allow the power supply
The eMMC signalling voltage is determined by VCCQ which is provided to the card by the host. Signalling is not required to begin at 3.3v and, if the host and card both support a particular VCC/VCCQ combination, it can be used immediately. In contrast, SD Cards must begin with 3.3v signalling and may switch to a lower voltage signalling if instructed to do so in CMD11. A message is required to coordinate this operation because the card only receives a 3.3v VDD and must know when to use the 1.8v produced by its internal regulator. It makes sense for the core to begin with 3.3v signalling but when that can't be set, 1.8v and 1.2v signalling also should be attempted. This is especially important when an external regulator with a limited range is used to supply VCCQ to an eMMC part. Signed-off-by: Tim Kryger <tim.kryger@linaro.org> --- drivers/mmc/core/core.c | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-)