@@ -380,6 +380,93 @@ enum dma_slave_buswidth {
DMA_SLAVE_BUSWIDTH_64_BYTES = 64,
};
+/**
+ * enum spi_transfer_cmd - spi transfer commands
+ */
+enum spi_transfer_cmd {
+ SPI_TX = 1,
+ SPI_RX,
+ SPI_DUPLEX,
+};
+
+/**
+ * struct dmaengine_spi_config - spi config for peripheral
+ *
+ * @loopback_en: spi loopback enable when set
+ * @clock_pol: clock polarity
+ * @data_pol: data polarity
+ * @pack_en: process tx/rx buffers as packed
+ * @word_len: spi word length
+ * @clk_div: source clock divider
+ * @clk_src: serial clock
+ * @cmd: spi cmd
+ * @cs: chip select toggle
+ */
+struct dmaengine_spi_config {
+ u8 loopback_en;
+ u8 clock_pol;
+ u8 data_pol;
+ u8 pack_en;
+ u8 word_len;
+ u32 clk_div;
+ u32 clk_src;
+ u8 fragmentation;
+ enum spi_transfer_cmd cmd;
+ u8 cs;
+};
+
+enum i2c_op {
+ I2C_WRITE = 1,
+ I2C_READ,
+};
+
+/**
+ * struct dmaengine_i2c_config - i2c config for peripheral
+ *
+ * @pack_enable: process tx/rx buffers as packed
+ * @cycle_count: clock cycles to be sent
+ * @high_count: high period of clock
+ * @low_count: low period of clock
+ * @clk_div: source clock divider
+ * @addr: i2c bus address
+ * @stretch: stretch the clock at eot
+ * @op: i2c cmd
+ */
+struct dmaengine_i2c_config {
+ u8 pack_enable;
+ u8 cycle_count;
+ u8 high_count;
+ u8 low_count;
+ u16 clk_div;
+ u8 addr;
+ u8 stretch;
+ enum i2c_op op;
+};
+
+enum dmaengine_peripheral {
+ DMAENGINE_PERIPHERAL_SPI = 1,
+ DMAENGINE_PERIPHERAL_UART = 2,
+ DMAENGINE_PERIPHERAL_I2C = 3,
+ DMAENGINE_PERIPHERAL_LAST = DMAENGINE_PERIPHERAL_I2C,
+};
+
+/**
+ * struct dmaengine_peripheral_config - peripheral configuration for
+ * dmaengine peripherals
+ *
+ * @peripheral: type of peripheral to DMA to/from
+ * @set_config: set peripheral config
+ * @rx_len: receive length for buffer
+ * @spi: peripheral config for spi
+ * @i2c: peripheral config for i2c
+ */
+struct dmaengine_peripheral_config {
+ enum dmaengine_peripheral peripheral;
+ u8 set_config;
+ u32 rx_len;
+ struct dmaengine_spi_config spi;
+ struct dmaengine_i2c_config i2c;
+};
/**
* struct dma_slave_config - dma slave channel runtime config
* @direction: whether the data shall go in or out on this slave
@@ -418,6 +505,8 @@ enum dma_slave_buswidth {
* @slave_id: Slave requester id. Only valid for slave channels. The dma
* slave peripheral will have unique id as dma requester which need to be
* pass as slave config.
+ * @peripheral: peripheral configuration for programming peripheral for
+ * dmaengine transfer
*
* This struct is passed in as configuration data to a DMA engine
* in order to set up a certain channel for DMA transport at runtime.
@@ -443,6 +532,7 @@ struct dma_slave_config {
u32 dst_port_window_size;
bool device_fc;
unsigned int slave_id;
+ struct dmaengine_peripheral_config *peripheral;
};
/**
Some complex dmaengine controllers have capability to program the peripheral device, so pass on the peripheral configuration as part of dma_slave_config Signed-off-by: Vinod Koul <vkoul@kernel.org> --- include/linux/dmaengine.h | 90 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 90 insertions(+)