| Message ID | 20200914173628.GA22508@yamamaya.is-a-geek.org |
|---|---|
| State | New |
| Headers | show |
| Series | PATCH: serial: 8250_pci: Add Realtek 816a and 816b | expand |
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c index 3eb2d485eaeb..55bb7b897d97 100644 --- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -5566,6 +5566,17 @@ static const struct pci_device_id serial_pci_tbl[] = { PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_wch384_4 }, + /* + * Realtek RealManage + */ + { PCI_VENDOR_ID_REALTEK, 0x816a, + PCI_ANY_ID, PCI_ANY_ID, + 0, 0, pbn_b0_1_115200 }, + + { PCI_VENDOR_ID_REALTEK, 0x816b, + PCI_ANY_ID, PCI_ANY_ID, + 0, 0, pbn_b0_1_115200 }, + /* Fintek PCI serial cards */ { PCI_DEVICE(0x1c29, 0x1104), .driver_data = pbn_fintek_4 }, { PCI_DEVICE(0x1c29, 0x1108), .driver_data = pbn_fintek_8 },
These serial ports are exposed by the OOB-management-engine on RealManage-enabled network cards (e.g. AMD DASH enabled systems using Realtek cards). Because these have 3 BARs, they fail the "num_iomem <= 1" check in serial_pci_guess_board. I've manually checked the two IOMEM regions and BAR 2 doesn't seem to respond to reads, but BAR 4 seems to be an MMIO version of the IO ports (untested). With this change, the ports are detected: 0000:02:00.1: ttyS0 at I/O 0x2200 (irq = 82, base_baud = 115200) is a 16550A 0000:02:00.2: ttyS1 at I/O 0x2100 (irq = 55, base_baud = 115200) is a 16550A lspci output: 02:00.1 0700: 10ec:816a (rev 0e) (prog-if 02 [16550]) Subsystem: 17aa:5082 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 82 IOMMU group: 11 Region 0: I/O ports at 2200 [size=256] Region 2: Memory at fd715000 (64-bit, non-prefetchable) [size=4K] Region 4: Memory at fd704000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v2) Endpoint, MSI 01 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s (ok), Width x1 (ok) TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+ 10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix- EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit- FRS- TPHComp- ExtTPHComp- AtomicOpsCap: 32bit- 64bit- 128bitCAS- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled, AtomicOpsCtl: ReqEn- LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1- EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest- Retimer- 2Retimers- CrosslinkRes: unsupported Capabilities: [b0] MSI-X: Enable- Count=4 Masked- Vector table: BAR=4 offset=00000000 PBA: BAR=4 offset=00000800 Capabilities: [d0] Vital Product Data Not readable Capabilities: [100 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn- MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap- HeaderLog: 00000000 00000000 00000000 00000000 Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00 Capabilities: [170 v1] Latency Tolerance Reporting Max snoop latency: 0ns Max no snoop latency: 0ns Capabilities: [178 v1] L1 PM Substates L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+ PortCommonModeRestoreTime=150us PortTPowerOnTime=150us L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1- T_CommonMode=0us LTR1.2_Threshold=0ns L1SubCtl2: T_PwrOn=10us 02:00.2 0700: 10ec:816b (rev 0e) [...same...] Signed-off-by: Tobias Diedrich <tobiasdiedrich@gmail.com> --- drivers/tty/serial/8250/8250_pci.c | 11 +++++++++++ 1 file changed, 11 insertions(+)