diff mbox series

[Resend,v1] Bluetooth: hci_qca: Enhance retry logic in qca_setup

Message ID 1605071653-5088-1-git-send-email-bgodavar@codeaurora.org
State New
Headers show
Series [Resend,v1] Bluetooth: hci_qca: Enhance retry logic in qca_setup | expand

Commit Message

Balakrishna Godavarthi Nov. 11, 2020, 5:14 a.m. UTC 
Currently driver only retries to download FW if FW downloading
is failed. Sometimes observed command timeout for version request
command, if this happen on some platforms during boot time, then
a reboot is needed to turn ON BT. Instead to avoid a reboot, now
extended retry logic for version request command too.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
---
 drivers/bluetooth/hci_qca.c | 34 ++++++++++++++++++----------------
 1 file changed, 18 insertions(+), 16 deletions(-)
diff mbox series

Patch

diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index 2d3f1f1..1c9a2d46 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -1672,7 +1672,7 @@  static int qca_setup(struct hci_uart *hu)
 retry:
 	ret = qca_power_on(hdev);
 	if (ret)
-		return ret;
+		goto out;
 
 	clear_bit(QCA_SSR_TRIGGERED, &qca->flags);
 
@@ -1681,7 +1681,7 @@  static int qca_setup(struct hci_uart *hu)
 
 		ret = qca_read_soc_version(hdev, &soc_ver, soc_type);
 		if (ret)
-			return ret;
+			goto out;
 	} else {
 		qca_set_speed(hu, QCA_INIT_SPEED);
 	}
@@ -1691,7 +1691,7 @@  static int qca_setup(struct hci_uart *hu)
 	if (speed) {
 		ret = qca_set_speed(hu, QCA_OPER_SPEED);
 		if (ret)
-			return ret;
+			goto out;
 
 		qca_baudrate = qca_get_baudrate_value(speed);
 	}
@@ -1700,7 +1700,7 @@  static int qca_setup(struct hci_uart *hu)
 		/* Get QCA version information */
 		ret = qca_read_soc_version(hdev, &soc_ver, soc_type);
 		if (ret)
-			return ret;
+			goto out;
 	}
 
 	bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver);
@@ -1721,20 +1721,22 @@  static int qca_setup(struct hci_uart *hu)
 		 * patch/nvm-config is found, so run with original fw/config.
 		 */
 		ret = 0;
-	} else {
-		if (retries < MAX_INIT_RETRIES) {
-			qca_power_shutdown(hu);
-			if (hu->serdev) {
-				serdev_device_close(hu->serdev);
-				ret = serdev_device_open(hu->serdev);
-				if (ret) {
-					bt_dev_err(hdev, "failed to open port");
-					return ret;
-				}
+	}
+
+out:
+	if (ret && retries < MAX_INIT_RETRIES) {
+		bt_dev_warn(hdev, "Retry BT power ON:%d", retries);
+		qca_power_shutdown(hu);
+		if (hu->serdev) {
+			serdev_device_close(hu->serdev);
+			ret = serdev_device_open(hu->serdev);
+			if (ret) {
+				bt_dev_err(hdev, "failed to open port");
+				return ret;
 			}
-			retries++;
-			goto retry;
 		}
+		retries++;
+		goto retry;
 	}
 
 	/* Setup bdaddr */