@@ -96,6 +96,21 @@ config USB_GADGET_VBUS_DRAW
This value will be used except for system-specific gadget
drivers that have more specific information.
+config USB_GADGET_STORAGE_NUM_BUFFERS
+ int "Number of storage pipline buffers"
+ range 2 64
+ default 2
+ help
+ Usually 2 buffers are enough to establish a good
+ double buffering pipeline. But when dealing with expensive
+ request preparation (i.e. dma_map) there may be benefits of
+ increasing the number of buffers. There is an extra cost for
+ every first request, the others are prepared in parallell with
+ an ongoing transfer. Every time all buffers are consumed there is
+ an additional cost for the next first request. Increasing the number
+ of buffers decreases the risk of running out of buffers.
+ If unsure, say 2.
+
config USB_GADGET_SELECTED
boolean
@@ -262,8 +262,8 @@ static struct fsg_lun *fsg_lun_from_dev(struct device *dev)
#define EP0_BUFSIZE 256
#define DELAYED_STATUS (EP0_BUFSIZE + 999) /* An impossibly large value */
-/* Number of buffers we will use. 2 is enough for double-buffering */
-#define FSG_NUM_BUFFERS 2
+/* Number of buffers we will use. 2 is usually enough for double-buffering */
+#define FSG_NUM_BUFFERS CONFIG_USB_GADGET_STORAGE_NUM_BUFFERS
/* Default size of buffer length. */
#define FSG_BUFLEN ((u32)16384)
FSG_NUM_BUFFERS is set to 2 as default. Usually 2 buffers are enough to establish a good double buffering pipeline. But when dealing with expensive request preparation (i.e. dma_map) there may be benefits of increasing the number of buffers. There is an extra cost for every first request, the others are prepared in parallell with an ongoing transfer. Every time all buffers are consumed there is an additional cost for the next first request. Increasing the number of buffers decreases the risk of running out of buffers. Test set up * Running dd on the host reading from the mass storage device * cmdline: dd if=/dev/sdb of=/dev/null bs=4k count=$((256*100)) * Caches are dropped on the host and on the device before each run Measurements on a Snowball board with ondemand_govenor active. FSG_NUM_BUFFERS 2 104857600 bytes (105 MB) copied, 5.62173 s, 18.7 MB/s 104857600 bytes (105 MB) copied, 5.61811 s, 18.7 MB/s 104857600 bytes (105 MB) copied, 5.57817 s, 18.8 MB/s 104857600 bytes (105 MB) copied, 5.57769 s, 18.8 MB/s 104857600 bytes (105 MB) copied, 5.59654 s, 18.7 MB/s 104857600 bytes (105 MB) copied, 5.58948 s, 18.8 MB/s FSG_NUM_BUFFERS 4 104857600 bytes (105 MB) copied, 5.26839 s, 19.9 MB/s 104857600 bytes (105 MB) copied, 5.2691 s, 19.9 MB/s 104857600 bytes (105 MB) copied, 5.2711 s, 19.9 MB/s 104857600 bytes (105 MB) copied, 5.27174 s, 19.9 MB/s 104857600 bytes (105 MB) copied, 5.27261 s, 19.9 MB/s 104857600 bytes (105 MB) copied, 5.27135 s, 19.9 MB/s 104857600 bytes (105 MB) copied, 5.27249 s, 19.9 MB/s There may not be one optimal number for all boards. That is the reason for adding the number to Kconfig, Signed-off-by: Per Forlin <per.forlin@linaro.org> --- drivers/usb/gadget/Kconfig | 15 +++++++++++++++ drivers/usb/gadget/storage_common.c | 4 ++-- 2 files changed, 17 insertions(+), 2 deletions(-)