new file mode 100644
@@ -0,0 +1,98 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/serial/silabs,si4455.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Silicon Labs Si4455 device tree bindings
+
+maintainers:
+ - József Horváth <info@ministro.hu>
+
+description:
+ This document is for describing the required device tree parameters for si4455 serial driver.
+ The si4455 driver tries to represent the Silicon Labs Si4455 sub-GHz transceiver device
+ like a serial port. The required parameters for proper operation are described below.
+ https://www.silabs.com/documents/public/data-sheets/Si4455.pdf
+
+allOf:
+ - $ref: "serial.yaml#"
+
+properties:
+ compatible:
+ const: silabs,si4455
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ spi-max-frequency:
+ description: maximum clock frequency on SPI port
+ maximum: 500000
+
+ shutdown-gpios:
+ description: gpio pin for SDN
+ maxItems: 1
+
+ silabs,package-size:
+ description:
+ Radio payload length, variable packet length is not supported by driver.
+ This value should equal with EZConfig payload length.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 64
+ minimum: 1
+
+ silabs,tx-channel:
+ description:
+ Radio transmit channel selection.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+ minimum: 0
+
+ silabs,rx-channel:
+ description:
+ Radio receive channel selection.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+ minimum: 0
+
+ silabs,ez-config:
+ description:
+ Radio configuration data file name.
+ $ref: /schemas/types.yaml#/definitions/string
+ items:
+ pattern: ^[0-9a-z\._\-]{1,255}$
+
+required:
+ - reg
+ - interrupts
+ - spi-max-frequency
+ - shutdown-gpios
+ - silabs,package-size
+ - silabs,tx-channel
+ - silabs,rx-channel
+ - silabs,ez-config
+
+additionalProperties: false
+
+examples:
+ - |
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ si4455_0: serial@0 {
+ compatible = "silabs,si4455";
+ reg = <0>;
+ interrupt-parent = <&gpio>;
+ interrupts = <7 2>;
+ shutdown-gpios = <&gpio 26 1>;
+ spi-max-frequency = <300000>;
+ silabs,package-size = <30>;
+ silabs,tx-channel = <1>;
+ silabs,rx-channel = <2>;
+ silabs,ez-config = "si4455_spi0_0.ez.bin";
+ };
+ };
+...
@@ -15952,6 +15952,13 @@ M: Jérôme Pouiller <jerome.pouiller@silabs.com>
S: Supported
F: drivers/staging/wfx/
+SILICON LABS SI4455 SERIAL DRIVER
+M: József Horváth <info@ministro.hu>
+S: Maintained
+F: Documentation/devicetree/bindings/staging/serial/silabs,si4455.yaml
+F: drivers/tty/serial/si4455.c
+F: drivers/tty/serial/si4455_api.h
+
SILICON MOTION SM712 FRAME BUFFER DRIVER
M: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
M: Teddy Wang <teddy.wang@siliconmotion.com>
@@ -1583,6 +1583,14 @@ config SERIAL_MILBEAUT_USIO_CONSOLE
receives all kernel messages and warnings and which allows logins in
single user mode).
+config SERIAL_SI4455
+ tristate "Si4455 support"
+ depends on SPI
+ select SERIAL_CORE
+ help
+ This driver is for Silicon Labs's Si4455 Sub-GHz transciver.
+ Say 'Y' here if you wish to use it as serial port.
+
endmenu
config SERIAL_MCTRL_GPIO
@@ -90,6 +90,7 @@ obj-$(CONFIG_SERIAL_OWL) += owl-uart.o
obj-$(CONFIG_SERIAL_RDA) += rda-uart.o
obj-$(CONFIG_SERIAL_MILBEAUT_USIO) += milbeaut_usio.o
obj-$(CONFIG_SERIAL_SIFIVE) += sifive.o
+obj-$(CONFIG_SERIAL_SI4455) += si4455.o
# GPIOLIB helpers for modem control lines
obj-$(CONFIG_SERIAL_MCTRL_GPIO) += serial_mctrl_gpio.o
new file mode 100644
@@ -0,0 +1,1328 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 József Horváth <info@ministro.hu>
+ *
+ */
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/gpio/driver.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
+#include <linux/regmap.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/spi/spi.h>
+#include <linux/uaccess.h>
+#include <linux/string.h>
+#include <linux/firmware.h>
+
+#define PORT_SI4455 1096
+#define SI4455_NAME "Si4455"
+#define SI4455_MAJOR 432
+#define SI4455_MINOR 567
+#define SI4455_UART_NRMAX 1
+#define SI4455_FIFO_SIZE 64
+
+#define SI4455_CMD_ID_EZCONFIG_CHECK 0x19
+#define SI4455_CMD_ID_PART_INFO 0x01
+#define SI4455_CMD_REPLY_COUNT_PART_INFO 9
+#define SI4455_CMD_ID_GET_INT_STATUS 0x20
+#define SI4455_CMD_REPLY_COUNT_GET_INT_STATUS 8
+#define SI4455_CMD_ID_FIFO_INFO 0x15
+#define SI4455_CMD_ARG_COUNT_FIFO_INFO 2
+#define SI4455_CMD_REPLY_COUNT_FIFO_INFO 2
+#define SI4455_CMD_FIFO_INFO_ARG_TX_BIT 0x01
+#define SI4455_CMD_FIFO_INFO_ARG_RX_BIT 0x02
+#define SI4455_CMD_ID_READ_CMD_BUFF 0x44
+#define SI4455_CMD_ID_READ_RX_FIFO 0x77
+#define SI4455_CMD_ID_WRITE_TX_FIFO 0x66
+#define SI4455_CMD_ID_START_RX 0x32
+#define SI4455_CMD_ARG_COUNT_START_RX 8
+#define SI4455_CMD_START_RX_RXTIMEOUT_STATE_RX 8
+#define SI4455_CMD_START_RX_RXVALID_STATE_RX 8
+#define SI4455_CMD_START_RX_RXINVALID_STATE_RX 8
+#define SI4455_CMD_ID_START_TX 0x31
+#define SI4455_CMD_ARG_COUNT_START_TX 5
+#define SI4455_CMD_ID_CHANGE_STATE 0x34
+#define SI4455_CMD_ARG_COUNT_CHANGE_STATE 2
+#define SI4455_CMD_CHANGE_STATE_STATE_READY 3
+#define SI4455_CMD_GET_CHIP_STATUS_ERROR_PEND_MASK 0x08
+#define SI4455_CMD_GET_CHIP_STATUS_ERROR_PEND_BIT 0x08
+#define SI4455_CMD_GET_INT_STATUS_PACKET_SENT_PEND_BIT 0x20
+#define SI4455_CMD_GET_INT_STATUS_PACKET_RX_PEND_BIT 0x10
+#define SI4455_CMD_GET_INT_STATUS_CRC_ERROR_BIT 0x08
+#define SI4455_CMD_ID_GET_MODEM_STATUS 0x22
+#define SI4455_CMD_ARG_COUNT_GET_MODEM_STATUS 2
+#define SI4455_CMD_REPLY_COUNT_GET_MODEM_STATUS 8
+
+struct si4455_part_info {
+ u8 chip_rev;
+ u16 part;
+ u8 pbuild;
+ u16 id;
+ u8 customer;
+ u8 rom_id;
+ u8 bond;
+};
+
+struct si4455_int_status {
+ u8 int_pend;
+ u8 int_status;
+ u8 ph_pend;
+ u8 ph_status;
+ u8 modem_pend;
+ u8 modem_status;
+ u8 chip_pend;
+ u8 chip_status;
+};
+
+struct si4455_modem_status {
+ u8 modem_pend;
+ u8 modem_status;
+ u8 curr_rssi;
+ u8 latch_rssi;
+ u8 ant1_rssi;
+ u8 ant2_rssi;
+ u16 afc_freq_offset;
+};
+
+struct si4455_fifo_info {
+ u8 rx_fifo_count;
+ u8 tx_fifo_space;
+};
+
+struct si4455_one {
+ struct uart_port port;
+ struct work_struct tx_work;
+};
+
+struct si4455_port {
+ struct mutex mutex; /* For syncing access to device */
+ int power_count;
+ bool connected;
+ struct gpio_desc *shdn_gpio;
+ struct si4455_part_info part_info;
+ struct si4455_modem_status modem_status;
+ u32 tx_channel;
+ u32 rx_channel;
+ u32 package_size;
+ bool configured;
+ bool tx_pending;
+ bool rx_pending;
+ u32 current_rssi;
+ struct si4455_one one;
+};
+
+static struct uart_driver si4455_uart = {
+ .owner = THIS_MODULE,
+ .driver_name = SI4455_NAME,
+#ifdef CONFIG_DEVFS_FS
+ .dev_name = "ttySI%d",
+#else
+ .dev_name = "ttySI",
+#endif
+ .major = SI4455_MAJOR,
+ .minor = SI4455_MINOR,
+ .nr = SI4455_UART_NRMAX,
+};
+
+static int si4455_get_response(struct uart_port *port, int length, u8 *data)
+{
+ int ret;
+ u8 data_out[] = { SI4455_CMD_ID_READ_CMD_BUFF };
+ u8 *data_in = NULL;
+ struct spi_transfer xfer[2];
+ int timeout = 10000;
+
+ if (length > 0 && !data)
+ return -EINVAL;
+
+ data_in = kzalloc(1 + length, GFP_KERNEL);
+ if (!data_in)
+ return -ENOMEM;
+
+ memset(&xfer, 0x00, sizeof(xfer));
+ xfer[0].tx_buf = data_out;
+ xfer[0].len = sizeof(data_out);
+ xfer[1].rx_buf = data_in;
+ xfer[1].len = 1 + length;
+
+ while (--timeout > 0) {
+ data_out[0] = SI4455_CMD_ID_READ_CMD_BUFF;
+ ret = spi_sync_transfer(to_spi_device(port->dev), xfer,
+ ARRAY_SIZE(xfer));
+ if (ret) {
+ dev_err(port->dev, "%s: spi_sync_transfer error(%i)", __func__, ret);
+ break;
+ }
+
+ if (data_in[0] == 0xFF) {
+ if (length > 0 && data)
+ memcpy(data, &data_in[1], length);
+
+ break;
+ }
+ usleep_range(100, 200);
+ }
+ if (timeout == 0) {
+ dev_err(port->dev, "%s:timeout==%i", __func__, timeout);
+ ret = -EIO;
+ }
+ kfree(data_in);
+ return ret;
+}
+
+static int si4455_poll_cts(struct uart_port *port)
+{
+ return si4455_get_response(port, 0, NULL);
+}
+
+static int si4455_send_command(struct uart_port *port, int length, u8 *data)
+{
+ int ret;
+
+ ret = si4455_poll_cts(port);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_poll_cts error(%i)", __func__, ret);
+ return ret;
+ }
+ ret = spi_write(to_spi_device(port->dev), data, length);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: spi_write error(%i)", __func__, ret);
+ }
+ return ret;
+}
+
+static int si4455_send_command_get_response(struct uart_port *port,
+ int out_length, u8 *data_out,
+ int in_length, u8 *data_in)
+{
+ int ret;
+
+ ret = si4455_send_command(port, out_length, data_out);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_send_command error(%i)", __func__, ret);
+ return ret;
+ }
+
+ ret = si4455_get_response(port, in_length, data_in);
+
+ return ret;
+}
+
+static int si4455_read_data(struct uart_port *port, u8 command, int poll,
+ int length, u8 *data)
+{
+ int ret = 0;
+ u8 data_out[] = { command };
+ struct spi_transfer xfer[] = {
+ {
+ .tx_buf = data_out,
+ .len = sizeof(data_out),
+ }, {
+ .rx_buf = data,
+ .len = length,
+ }
+ };
+
+ if (poll) {
+ ret = si4455_poll_cts(port);
+ if (ret)
+ return ret;
+ }
+
+ ret = spi_sync_transfer(to_spi_device(port->dev),
+ xfer,
+ ARRAY_SIZE(xfer));
+ if (ret) {
+ dev_err(port->dev,
+ "%s: spi_sync_transfer error(%i)", __func__, ret);
+ }
+ return ret;
+}
+
+static int si4455_write_data(struct uart_port *port, u8 command, int poll,
+ int length, const u8 *data)
+{
+ int ret = 0;
+ u8 *data_out;
+
+ if (poll) {
+ ret = si4455_poll_cts(port);
+ if (ret)
+ return ret;
+ }
+
+ data_out = kzalloc(1 + length, GFP_KERNEL);
+ if (!data_out)
+ return -ENOMEM;
+
+ data_out[0] = command;
+ memcpy(&data_out[1], data, length);
+ ret = spi_write(to_spi_device(port->dev), data_out, 1 + length);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: spi_write error(%i)", __func__, ret);
+ }
+ kfree(data_out);
+
+ return ret;
+}
+
+static void si4455_set_power(struct si4455_port *priv, int on)
+{
+ if (!priv->shdn_gpio)
+ return;
+ if (on) {
+ gpiod_direction_output(priv->shdn_gpio, 0);
+ usleep_range(4000, 5000);
+ gpiod_set_value(priv->shdn_gpio, 1);
+ usleep_range(4000, 5000);
+ } else {
+ gpiod_direction_output(priv->shdn_gpio, 0);
+ }
+}
+
+static int si4455_s_power(struct device *dev, int on)
+{
+ struct si4455_port *s = dev_get_drvdata(dev);
+
+ dev_dbg(dev, "%s(on=%d)\n", __func__, on);
+ if (s->power_count == !on)
+ si4455_set_power(s, on);
+ s->power_count += on ? 1 : -1;
+ WARN_ON(s->power_count < 0);
+
+ return 0;
+}
+
+static int si4455_get_part_info(struct uart_port *port,
+ struct si4455_part_info *result)
+{
+ int ret;
+ u8 data_out[] = { SI4455_CMD_ID_PART_INFO };
+ u8 data_in[SI4455_CMD_REPLY_COUNT_PART_INFO];
+
+ ret = si4455_send_command_get_response(port, sizeof(data_out), data_out,
+ sizeof(data_in), data_in);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_send_command_get_response error(%i)",
+ __func__, ret);
+ return ret;
+ }
+
+ result->chip_rev = data_in[0];
+ memcpy(&result->part, &data_in[1], sizeof(result->part));
+ result->pbuild = data_in[3];
+ memcpy(&result->id, &data_in[4], sizeof(result->id));
+ result->customer = data_in[6];
+ result->rom_id = data_in[7];
+ result->bond = data_in[8];
+
+ return ret;
+}
+
+static int si4455_get_int_status(struct uart_port *port, u8 ph_clear,
+ u8 modem_clear, u8 chip_clear,
+ struct si4455_int_status *result)
+{
+ int ret;
+ u8 data_out[] = {
+ SI4455_CMD_ID_GET_INT_STATUS,
+ ph_clear,
+ modem_clear,
+ chip_clear
+ };
+ u8 data_in[SI4455_CMD_REPLY_COUNT_GET_INT_STATUS];
+
+ ret = si4455_send_command_get_response(port, sizeof(data_out), data_out,
+ sizeof(data_in), data_in);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_send_command_get_response error(%i)",
+ __func__, ret);
+ } else {
+ result->int_pend = data_in[0];
+ result->int_status = data_in[1];
+ result->ph_pend = data_in[2];
+ result->ph_status = data_in[3];
+ result->modem_pend = data_in[4];
+ result->modem_status = data_in[5];
+ result->chip_pend = data_in[6];
+ result->chip_status = data_in[7];
+ }
+ return ret;
+}
+
+static int si4455_get_modem_status(struct uart_port *port, u8 modem_clear,
+ struct si4455_modem_status *result)
+{
+ int ret;
+ u8 data_out[] = {
+ SI4455_CMD_ID_GET_MODEM_STATUS,
+ modem_clear,
+ };
+ u8 data_in[SI4455_CMD_REPLY_COUNT_GET_MODEM_STATUS];
+
+ ret = si4455_send_command_get_response(port, sizeof(data_out), data_out,
+ sizeof(data_in), data_in);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_send_command_get_response error(%i)",
+ __func__, ret);
+ } else {
+ result->modem_pend = data_in[0];
+ result->modem_status = data_in[1];
+ result->curr_rssi = data_in[2];
+ result->latch_rssi = data_in[3];
+ result->ant1_rssi = data_in[4];
+ result->ant2_rssi = data_in[5];
+ memcpy(&result->afc_freq_offset,
+ &data_in[6], sizeof(result->afc_freq_offset));
+ }
+ return ret;
+}
+
+static int si4455_fifo_info(struct uart_port *port, u8 fifo,
+ struct si4455_fifo_info *result)
+{
+ int ret;
+ u8 data_out[SI4455_CMD_ARG_COUNT_FIFO_INFO] = {
+ SI4455_CMD_ID_FIFO_INFO, fifo
+ };
+ u8 data_in[SI4455_CMD_REPLY_COUNT_FIFO_INFO] = { 0 };
+
+ ret = si4455_send_command_get_response(port, sizeof(data_out), data_out,
+ sizeof(data_in), data_in);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_send_command_get_response error(%i)",
+ __func__, ret);
+ } else {
+ result->rx_fifo_count = data_in[0];
+ result->tx_fifo_space = data_in[1];
+ }
+ return ret;
+}
+
+static int si4455_read_rx_fifo(struct uart_port *port, int length, u8 *data)
+{
+ return si4455_read_data(port, SI4455_CMD_ID_READ_RX_FIFO, 0, length,
+ data);
+}
+
+static int si4455_write_tx_fifo(struct uart_port *port, int length, u8 *data)
+{
+ return si4455_write_data(port, SI4455_CMD_ID_WRITE_TX_FIFO, 0, length,
+ data);
+}
+
+static int si4455_rx(struct uart_port *port, u32 channel, u8 condition,
+ u16 length, u8 next_state1, u8 next_state2,
+ u8 next_state3)
+{
+ u8 data_out[SI4455_CMD_ARG_COUNT_START_RX];
+
+ data_out[0] = SI4455_CMD_ID_START_RX;
+ data_out[1] = channel;
+ data_out[2] = condition;
+ data_out[3] = (u8)(length >> 8);
+ data_out[4] = (u8)(length);
+ data_out[5] = next_state1;
+ data_out[6] = next_state2;
+ data_out[7] = next_state3;
+
+ return si4455_send_command(port, SI4455_CMD_ARG_COUNT_START_RX,
+ data_out);
+}
+
+static int si4455_tx(struct uart_port *port, u8 channel, u8 condition,
+ u16 length)
+{
+ u8 data_out[/*6*/ SI4455_CMD_ARG_COUNT_START_TX];
+
+ data_out[0] = SI4455_CMD_ID_START_TX;
+ data_out[1] = channel;
+ data_out[2] = condition;
+ data_out[3] = (u8)(length >> 8);
+ data_out[4] = (u8)(length);
+ /*TODO: data_out[5] = 0x44; in case of rev c2a*/
+
+ return si4455_send_command(port, /*6*/ SI4455_CMD_ARG_COUNT_START_TX,
+ data_out);
+}
+
+static int si4455_change_state(struct uart_port *port, u8 next_state1)
+{
+ u8 data_out[SI4455_CMD_ARG_COUNT_CHANGE_STATE];
+
+ data_out[0] = SI4455_CMD_ID_CHANGE_STATE;
+ data_out[1] = (u8)next_state1;
+
+ return si4455_send_command(port, SI4455_CMD_ARG_COUNT_CHANGE_STATE,
+ data_out);
+}
+
+static int si4455_begin_tx(struct uart_port *port, u32 channel, int length,
+ u8 *data)
+{
+ int ret = 0;
+ struct si4455_int_status int_status = { 0 };
+ struct si4455_fifo_info fifo_info = { 0 };
+
+ dev_dbg(port->dev, "%s(%u, %u)", __func__, channel, length);
+ if (length > SI4455_FIFO_SIZE || length < 0)
+ return -EINVAL;
+
+ ret = si4455_change_state(port,
+ SI4455_CMD_CHANGE_STATE_STATE_READY);
+ if (ret) {
+ dev_err(port->dev, "%s: si4455_change_state error(%i)",
+ __func__, ret);
+ return ret;
+ }
+ ret = si4455_get_int_status(port, 0, 0, 0, &int_status);
+ if (ret) {
+ dev_err(port->dev, "%s: si4455_get_int_status error(%i)",
+ __func__, ret);
+ return ret;
+ }
+ ret = si4455_fifo_info(port,
+ SI4455_CMD_FIFO_INFO_ARG_TX_BIT, &fifo_info);
+ if (ret) {
+ dev_err(port->dev, "%s: si4455_fifo_info error(%i)",
+ __func__, ret);
+ return ret;
+ }
+ ret = si4455_write_tx_fifo(port, (u16)length, data);
+ if (ret) {
+ dev_err(port->dev, "%s: si4455_write_tx_fifo error(%i)",
+ __func__, ret);
+ return ret;
+ }
+ ret = si4455_tx(port, channel, 0x30, length);
+ if (ret) {
+ dev_err(port->dev, "%s: si4455_tx error(%i)",
+ __func__, ret);
+ return ret;
+ }
+ return 0;
+}
+
+static int si4455_end_tx(struct uart_port *port)
+{
+ int ret = 0;
+ struct si4455_int_status int_status = { 0 };
+
+ ret = si4455_change_state(port,
+ SI4455_CMD_CHANGE_STATE_STATE_READY);
+ if (ret) {
+ dev_err(port->dev, "%s: si4455_change_state error(%i)",
+ __func__, ret);
+ return ret;
+ }
+ ret = si4455_get_int_status(port, 0, 0, 0, &int_status);
+ if (ret) {
+ dev_err(port->dev, "%s: si4455_get_int_status error(%i)",
+ __func__, ret);
+ return ret;
+ }
+ return 0;
+}
+
+static int si4455_begin_rx(struct uart_port *port, u32 channel, u32 length)
+{
+ int ret = 0;
+ struct si4455_int_status int_status = { 0 };
+ struct si4455_fifo_info fifo_info = { 0 };
+
+ dev_dbg(port->dev, "%s(%u, %u)", __func__, channel, length);
+ ret = si4455_get_int_status(port, 0, 0, 0, &int_status);
+ if (ret) {
+ dev_err(port->dev, "%s: si4455_get_int_status error(%i)",
+ __func__, ret);
+ return ret;
+ }
+ ret = si4455_fifo_info(port,
+ SI4455_CMD_FIFO_INFO_ARG_RX_BIT,
+ &fifo_info);
+ if (ret) {
+ dev_err(port->dev, "%s: si4455_fifo_info error(%i)",
+ __func__, ret);
+ return ret;
+ }
+ ret = si4455_rx(port, channel, 0x00, length,
+ SI4455_CMD_START_RX_RXTIMEOUT_STATE_RX,
+ SI4455_CMD_START_RX_RXVALID_STATE_RX,
+ SI4455_CMD_START_RX_RXINVALID_STATE_RX);
+ if (ret) {
+ dev_err(port->dev, "%s: si4455_rx error(%i)",
+ __func__, ret);
+ return ret;
+ }
+ return 0;
+}
+
+static int si4455_end_rx(struct uart_port *port, u32 length, u8 *data)
+{
+ return si4455_read_rx_fifo(port, length, data);
+}
+
+static int si4455_configure(struct uart_port *port, const u8 *configuration_data)
+{
+ int ret = 0;
+ u8 col;
+ u8 response;
+ u8 count;
+ struct si4455_int_status int_status = { 0 };
+ u8 radio_cmd[16u];
+
+ /* While cycle as far as the pointer points to a command */
+ while (*configuration_data != 0x00) {
+ /* Commands structure in the array:
+ * --------------------------------
+ * LEN | <LEN length of data>
+ */
+ count = *configuration_data++;
+ dev_dbg(port->dev, "%s: count(%u)",
+ __func__, count);
+ if (count > 16u) {
+ /* Initial configuration of Si4x55 */
+ if (SI4455_CMD_ID_WRITE_TX_FIFO
+ == *configuration_data) {
+ if (count > 128u) {
+ /* Number of command bytes exceeds
+ * maximal allowable length
+ */
+ dev_err(port->dev, "%s: command length error(%i)",
+ __func__, count);
+ ret = -EINVAL;
+ break;
+ }
+
+ /* Load array to the device */
+ configuration_data++;
+ ret = si4455_write_data(port,
+ SI4455_CMD_ID_WRITE_TX_FIFO,
+ 1,
+ count - 1,
+ configuration_data);
+ if (ret) {
+ dev_err(port->dev, "%s: si4455_write_data error(%i)",
+ __func__, ret);
+ break;
+ }
+
+ /* Point to the next command */
+ configuration_data += count - 1;
+
+ /* Continue command interpreter */
+ continue;
+ } else {
+ /* Number of command bytes exceeds
+ * maximal allowable length
+ */
+ ret = -EINVAL;
+ break;
+ }
+ }
+
+ for (col = 0u; col < count; col++) {
+ radio_cmd[col] = *configuration_data;
+ configuration_data++;
+ }
+
+ dev_dbg(port->dev, "%s: radio_cmd[0](%u)", __func__, radio_cmd[0]);
+ ret = si4455_send_command_get_response(port, count, radio_cmd,
+ 1, &response);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_send_command_get_response error(%i)",
+ __func__, ret);
+ break;
+ }
+
+ /* Check response byte of EZCONFIG_CHECK command */
+ if (radio_cmd[0] == SI4455_CMD_ID_EZCONFIG_CHECK) {
+ if (response) {
+ /* Number of command bytes exceeds
+ * maximal allowable length
+ */
+ ret = -EIO;
+ dev_err(port->dev, "%s: EZConfig check error(%i)",
+ __func__, radio_cmd[0]);
+ break;
+ }
+ }
+
+ /* Get and clear all interrupts. An error has occurred... */
+ si4455_get_int_status(port, 0, 0, 0, &int_status);
+ if (int_status.chip_pend
+ & SI4455_CMD_GET_CHIP_STATUS_ERROR_PEND_MASK) {
+ ret = -EIO;
+ dev_err(port->dev, "%s: chip error(%i)",
+ __func__, int_status.chip_pend);
+ break;
+ }
+ }
+
+ return ret;
+}
+
+static int si4455_re_configure(struct uart_port *port, const struct firmware *configuration)
+{
+ int ret = 0;
+ struct si4455_port *s = dev_get_drvdata(port->dev);
+
+ mutex_lock(&s->mutex);
+ s->configured = 0;
+ if (s->power_count > 0)
+ si4455_s_power(port->dev, 0);
+
+ si4455_s_power(port->dev, 1);
+ ret = si4455_configure(port, configuration->data);
+ if (ret == 0)
+ s->configured = 1;
+ mutex_unlock(&s->mutex);
+ return ret;
+}
+
+static int si4455_do_work(struct uart_port *port)
+{
+ int ret = 0;
+ struct si4455_port *s = dev_get_drvdata(port->dev);
+ struct circ_buf *xmit = &port->state->xmit;
+ unsigned int tx_pending = 0;
+ unsigned int tx_to_end = 0;
+ u8 *data = NULL;
+
+ mutex_lock(&s->mutex);
+ dev_dbg(port->dev, "%s(connected=%i, configured=%i, power_count=%i)",
+ __func__, s->connected, s->configured, s->power_count);
+ if (s->connected && s->configured && s->power_count > 0) {
+ if (!(uart_circ_empty(xmit) || uart_tx_stopped(port) || s->tx_pending)) {
+ tx_pending = uart_circ_chars_pending(xmit);
+ if (s->package_size > 0) {
+ if (tx_pending >= s->package_size) {
+ tx_pending = s->package_size;
+ data = kzalloc(s->package_size, GFP_KERNEL);
+ tx_to_end = CIRC_CNT_TO_END(xmit->head,
+ xmit->tail,
+ UART_XMIT_SIZE);
+ if (tx_to_end < tx_pending) {
+ memcpy(data,
+ xmit->buf + xmit->tail,
+ tx_to_end);
+ memcpy(data,
+ xmit->buf,
+ tx_pending - tx_to_end);
+ } else {
+ memcpy(data,
+ xmit->buf + xmit->tail,
+ tx_pending);
+ }
+ if (si4455_begin_tx(port, s->tx_channel,
+ tx_pending, data) == 0) {
+ s->tx_pending = true;
+ }
+ kfree(data);
+ }
+ } else {
+ //TODO: variable packet length
+ }
+ }
+ if (!s->tx_pending) {
+ if (s->package_size > 0) {
+ ret = si4455_begin_rx(port, s->rx_channel,
+ s->package_size);
+ } else {
+ //TODO: variable packet length
+ }
+ }
+ }
+ mutex_unlock(&s->mutex);
+ return ret;
+}
+
+static void si4455_handle_rx_pend(struct si4455_port *s)
+{
+ struct uart_port *port = &s->one.port;
+ u8 *data = NULL;
+ int sret = 0;
+ int i = 0;
+
+ if (s->package_size > 0) {
+ data = kzalloc(s->package_size, GFP_KERNEL);
+ sret = si4455_end_rx(port, s->package_size, data);
+ if (sret == 0) {
+ for (i = 0; i < s->package_size; i++) {
+ uart_insert_char(port, 0, 0, data[i], TTY_NORMAL);
+ port->icount.rx++;
+ }
+ tty_flip_buffer_push(&port->state->port);
+ } else {
+ dev_err(port->dev,
+ "%s: si4455_end_rx error(%i)",
+ __func__,
+ sret);
+ }
+ kfree(data);
+ } else {
+ //TODO: variable packet length
+ }
+}
+
+static void si4455_handle_tx_pend(struct si4455_port *s)
+{
+ struct uart_port *port = &s->one.port;
+ struct circ_buf *xmit = &port->state->xmit;
+
+ if (s->tx_pending) {
+ if (s->package_size) {
+ port->icount.tx += s->package_size;
+ xmit->tail = (xmit->tail + s->package_size)
+ & (UART_XMIT_SIZE - 1);
+ } else {
+ //TODO: variable packet length
+ }
+ si4455_end_tx(port);
+ s->tx_pending = 0;
+ }
+}
+
+static irqreturn_t si4455_port_irq(struct si4455_port *s)
+{
+ struct uart_port *port = &s->one.port;
+ irqreturn_t ret = IRQ_NONE;
+ struct si4455_int_status int_status = { 0 };
+ struct si4455_fifo_info fifo_info = { 0 };
+
+ mutex_lock(&s->mutex);
+ if (s->connected && s->configured && s->power_count > 0) {
+ if (!si4455_get_int_status(port, 0, 0, 0, &int_status)) {
+ si4455_get_modem_status(port, 0, &s->modem_status);
+ if (int_status.chip_pend
+ & SI4455_CMD_GET_CHIP_STATUS_ERROR_PEND_BIT) {
+ dev_err(port->dev,
+ "%s: chip_status:CMD_ERROR_PEND",
+ __func__);
+ } else if (int_status.ph_pend
+ & SI4455_CMD_GET_INT_STATUS_PACKET_SENT_PEND_BIT) {
+ dev_dbg(port->dev,
+ "%s: ph_status:PACKET_SENT_PEND",
+ __func__);
+ si4455_handle_tx_pend(s);
+ } else if (int_status.ph_pend
+ & SI4455_CMD_GET_INT_STATUS_PACKET_RX_PEND_BIT) {
+ dev_dbg(port->dev,
+ "%s: ph_status:PACKET_RX_PEND",
+ __func__);
+ s->current_rssi = s->modem_status.curr_rssi;
+ si4455_fifo_info(port, 0, &fifo_info);
+ si4455_handle_rx_pend(s);
+ } else if (int_status.ph_pend
+ & SI4455_CMD_GET_INT_STATUS_CRC_ERROR_BIT) {
+ dev_dbg(port->dev,
+ "%s: ph_status:CRC_ERROR_PEND",
+ __func__);
+ }
+ ret = IRQ_HANDLED;
+ }
+ } else {
+ ret = IRQ_HANDLED;
+ }
+ mutex_unlock(&s->mutex);
+ si4455_do_work(port);
+ return ret;
+}
+
+static irqreturn_t si4455_ist(int irq, void *dev_id)
+{
+ struct si4455_port *s = (struct si4455_port *)dev_id;
+ bool handled = false;
+
+ if (si4455_port_irq(s) == IRQ_HANDLED)
+ handled = true;
+
+ return IRQ_RETVAL(handled);
+}
+
+static void si4455_tx_proc(struct work_struct *ws)
+{
+ struct si4455_one *one = container_of(ws, struct si4455_one, tx_work);
+
+ si4455_do_work(&one->port);
+}
+
+static unsigned int si4455_tx_empty(struct uart_port *port)
+{
+ return TIOCSER_TEMT;
+}
+
+static unsigned int si4455_get_mctrl(struct uart_port *port)
+{
+ dev_dbg(port->dev, "%s", __func__);
+ return TIOCM_DSR | TIOCM_CAR;
+}
+
+static void si4455_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ dev_dbg(port->dev, "%s", __func__);
+}
+
+static void si4455_set_termios(struct uart_port *port, struct ktermios *termios,
+ struct ktermios *old)
+{
+ dev_dbg(port->dev, "%s", __func__);
+ if ((termios->c_cflag & CSIZE) != CS8)
+ dev_err(port->dev, "%s: CSIZE must be CS8", __func__);
+}
+
+static int si4455_startup(struct uart_port *port)
+{
+ struct si4455_port *s = dev_get_drvdata(port->dev);
+
+ dev_dbg(port->dev, "%s", __func__);
+ mutex_lock(&s->mutex);
+ s->connected = true;
+ mutex_unlock(&s->mutex);
+ return si4455_do_work(port);
+}
+
+static void si4455_shutdown(struct uart_port *port)
+{
+ struct si4455_port *s = dev_get_drvdata(port->dev);
+
+ dev_dbg(port->dev, "%s", __func__);
+ mutex_lock(&s->mutex);
+ s->connected = false;
+ mutex_unlock(&s->mutex);
+}
+
+static const char *si4455_type(struct uart_port *port)
+{
+ struct si4455_port *s = dev_get_drvdata(port->dev);
+
+ if (port->type != PORT_SI4455)
+ return NULL;
+ if (s->part_info.rom_id == 3)
+ return "SI4455-B1A";
+ else if (s->part_info.rom_id == 6)
+ return "SI4455-C2A";
+
+ return "SI4455(UNKNOWN-REV)";
+}
+
+static void si4455_config_port(struct uart_port *port, int flags)
+{
+ dev_dbg(port->dev, "%s", __func__);
+ if (flags & UART_CONFIG_TYPE)
+ port->type = PORT_SI4455;
+}
+
+static int si4455_verify_port(struct uart_port *port, struct serial_struct *s)
+{
+ if (s->type != PORT_UNKNOWN && s->type != PORT_SI4455)
+ return -EINVAL;
+
+ if (s->irq != port->irq)
+ return -EINVAL;
+
+ return 0;
+}
+
+static void si4455_start_tx(struct uart_port *port)
+{
+ struct si4455_one *one = container_of(port,
+ struct si4455_one,
+ port);
+
+ dev_dbg(port->dev, "%s", __func__);
+
+ if (!work_pending(&one->tx_work))
+ schedule_work(&one->tx_work);
+}
+
+static void si4455_null_void(struct uart_port *port)
+{
+ /* Do nothing */
+}
+
+static const struct uart_ops si4455_ops = {
+ .tx_empty = si4455_tx_empty,
+ .set_mctrl = si4455_set_mctrl,/* required */
+ .get_mctrl = si4455_get_mctrl,
+ .stop_tx = si4455_null_void,
+ .start_tx = si4455_start_tx,
+ .stop_rx = si4455_null_void,
+ .startup = si4455_startup,
+ .shutdown = si4455_shutdown,
+ .set_termios = si4455_set_termios,/* required */
+ .type = si4455_type,
+ .release_port = si4455_null_void,
+ .config_port = si4455_config_port,
+ .verify_port = si4455_verify_port,
+};
+
+static int __maybe_unused si4455_suspend(struct device *dev)
+{
+ struct si4455_port *s = dev_get_drvdata(dev);
+
+ uart_suspend_port(&si4455_uart, &s->one.port);
+ return 0;
+}
+
+static int __maybe_unused si4455_resume(struct device *dev)
+{
+ struct si4455_port *s = dev_get_drvdata(dev);
+
+ uart_resume_port(&si4455_uart, &s->one.port);
+
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(si4455_pm_ops, si4455_suspend, si4455_resume);
+
+static ssize_t package_size_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct si4455_port *s = dev_get_drvdata(dev);
+
+ return sprintf(buf, "%u\n", s->package_size);
+}
+
+static ssize_t package_size_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct si4455_port *s = dev_get_drvdata(dev);
+ unsigned long val;
+ int ret;
+
+ ret = kstrtoul(buf, 10, &val);
+ if (ret)
+ return ret;
+
+ if (val > SI4455_FIFO_SIZE)
+ return -EINVAL;
+
+ s->package_size = val;
+ ret = si4455_do_work(&s->one.port);
+
+ return ret ? ret : count;
+}
+static DEVICE_ATTR_RW(package_size);
+
+static ssize_t rx_channel_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct si4455_port *s = dev_get_drvdata(dev);
+
+ return sprintf(buf, "%u\n", s->rx_channel);
+}
+
+static ssize_t rx_channel_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct si4455_port *s = dev_get_drvdata(dev);
+ unsigned long val;
+ int ret;
+
+ ret = kstrtoul(buf, 10, &val);
+ if (ret)
+ return ret;
+
+ s->rx_channel = val;
+ ret = si4455_do_work(&s->one.port);
+
+ return ret ? ret : count;
+}
+static DEVICE_ATTR_RW(rx_channel);
+
+static ssize_t tx_channel_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct si4455_port *s = dev_get_drvdata(dev);
+
+ return sprintf(buf, "%u\n", s->tx_channel);
+}
+
+static ssize_t tx_channel_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct si4455_port *s = dev_get_drvdata(dev);
+ unsigned long val;
+ int ret;
+
+ ret = kstrtoul(buf, 10, &val);
+ if (ret)
+ return ret;
+
+ s->tx_channel = val;
+ ret = si4455_do_work(&s->one.port);
+
+ return ret ? ret : count;
+}
+static DEVICE_ATTR_RW(tx_channel);
+
+static ssize_t current_rssi_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct si4455_port *s = dev_get_drvdata(dev);
+
+ return sprintf(buf, "%u\n", s->current_rssi);
+}
+
+static DEVICE_ATTR(current_rssi, 0644, current_rssi_show, NULL);
+
+static struct attribute *si4455_attributes[] = {
+ &dev_attr_package_size.attr,
+ &dev_attr_rx_channel.attr,
+ &dev_attr_tx_channel.attr,
+ &dev_attr_current_rssi.attr,
+ NULL
+};
+
+static const struct attribute_group si4455_attr_group = {
+ .attrs = si4455_attributes,
+};
+
+static int si4455_probe(struct device *dev,
+ int irq)
+{
+ int ret;
+ struct si4455_port *s;
+ const void *of_ptr;
+ char ez_fw_name[255] = { 0 };
+ const struct firmware *ez_fw = NULL;
+
+ /* Alloc port structure */
+ dev_dbg(dev, "%s\n", __func__);
+ s = devm_kzalloc(dev, sizeof(*s), GFP_KERNEL);
+ if (!s) {
+ dev_err(dev, "Error allocating port structure\n");
+ return -ENOMEM;
+ }
+
+ dev_set_drvdata(dev, s);
+ mutex_init(&s->mutex);
+
+ s->shdn_gpio = devm_gpiod_get(dev, "shutdown", GPIOD_OUT_HIGH);
+ if (IS_ERR(s->shdn_gpio)) {
+ dev_err(dev, "Unable to reguest shdn gpio\n");
+ ret = -EINVAL;
+ goto out_generic;
+ }
+
+ of_ptr = of_get_property(dev->of_node, "silabs,package-size", NULL);
+ if (IS_ERR_OR_NULL(of_ptr)) {
+ dev_err(dev, "dt silabs,package-size property not present\n");
+ ret = -EINVAL;
+ goto out_generic;
+ }
+ s->package_size = be32_to_cpup(of_ptr);
+ if (s->package_size > SI4455_FIFO_SIZE) {
+ dev_err(dev, "dt silabs,package-size property maximum is %i\n", SI4455_FIFO_SIZE);
+ ret = -EINVAL;
+ goto out_generic;
+ }
+
+ of_ptr = of_get_property(dev->of_node, "silabs,tx-channel", NULL);
+ if (IS_ERR_OR_NULL(of_ptr)) {
+ dev_err(dev, "dt silabs,tx-channel property not present\n");
+ ret = -EINVAL;
+ goto out_generic;
+ }
+ s->tx_channel = be32_to_cpup(of_ptr);
+
+ of_ptr = of_get_property(dev->of_node, "silabs,rx-channel", NULL);
+ if (IS_ERR_OR_NULL(of_ptr)) {
+ dev_err(dev, "dt silabs,rx-channel property not present\n");
+ ret = -EINVAL;
+ goto out_generic;
+ }
+ s->rx_channel = be32_to_cpup(of_ptr);
+
+ of_ptr = of_get_property(dev->of_node, "silabs,ez-config", NULL);
+ if (IS_ERR_OR_NULL(of_ptr)) {
+ dev_err(dev, "dt silabs,ez-config property not present\n");
+ ret = -EINVAL;
+ goto out_generic;
+ }
+ strncpy(ez_fw_name, of_ptr, sizeof(ez_fw_name) - 1);
+
+ /* Initialize port data */
+ s->one.port.dev = dev;
+ s->one.port.line = 0;
+ s->one.port.irq = irq;
+ s->one.port.type = PORT_SI4455;
+ s->one.port.fifosize = SI4455_FIFO_SIZE;
+ s->one.port.flags = UPF_FIXED_TYPE | UPF_LOW_LATENCY;
+ s->one.port.iotype = UPIO_PORT;
+ s->one.port.iobase = 0x00;
+ s->one.port.membase = (void __iomem *)~0;
+ s->one.port.rs485_config = NULL;
+ s->one.port.ops = &si4455_ops;
+
+ si4455_s_power(dev, 1);
+
+ //detect
+ ret = si4455_get_part_info(&s->one.port, &s->part_info);
+ dev_dbg(dev, "si4455_get_part_info()==%i", ret);
+ if (ret == 0) {
+ dev_dbg(dev, "partInfo.chip_rev= %u", s->part_info.chip_rev);
+ dev_dbg(dev, "partInfo.part= %u", s->part_info.part);
+ dev_dbg(dev, "partInfo.pbuild= %u", s->part_info.pbuild);
+ dev_dbg(dev, "partInfo.id= %u", s->part_info.id);
+ dev_dbg(dev, "partInfo.customer= %u", s->part_info.customer);
+ dev_dbg(dev, "partInfo.rom_id= %u", s->part_info.rom_id);
+ dev_dbg(dev, "partInfo.bond= %u", s->part_info.bond);
+ if (s->part_info.part != 0x5544) {
+ dev_err(dev, "part(%u) error", s->part_info.part);
+ ret = -ENODEV;
+ }
+ }
+
+ if (ret)
+ goto out_generic;
+
+ ret = request_firmware(&ez_fw, ez_fw_name, dev);
+ if (ret) {
+ dev_err(dev, "firmware(%s) request error(%i)\n", ez_fw_name, ret);
+ ret = -EINVAL;
+ goto out_generic;
+ }
+
+ ret = si4455_re_configure(&s->one.port, ez_fw);
+ release_firmware(ez_fw);
+ if (ret) {
+ dev_err(dev, "device configuration error(%i)\n", ret);
+ ret = -EINVAL;
+ goto out_generic;
+ }
+
+ /* Initialize queue for start TX */
+ INIT_WORK(&s->one.tx_work, si4455_tx_proc);
+
+ /* Register port */
+ ret = uart_add_one_port(&si4455_uart, &s->one.port);
+ if (ret) {
+ s->one.port.dev = NULL;
+ goto out_uart;
+ }
+
+ ret = sysfs_create_group(&dev->kobj, &si4455_attr_group);
+ if (ret) {
+ dev_err(dev, "sysfs_create_group error(%i)\n", ret);
+ goto out_uart;
+ }
+ /* Setup interrupt */
+ ret = devm_request_threaded_irq(dev, irq, NULL, si4455_ist,
+ IRQF_ONESHOT | IRQF_SHARED,
+ dev_name(dev), s);
+
+ if (!ret)
+ return 0;
+
+ dev_err(dev, "Unable to reguest IRQ %i\n", irq);
+ sysfs_remove_group(&dev->kobj, &si4455_attr_group);
+
+out_uart:
+ uart_remove_one_port(&si4455_uart, &s->one.port);
+out_generic:
+ mutex_destroy(&s->mutex);
+ si4455_s_power(dev, 0);
+
+ return ret;
+}
+
+static int si4455_remove(struct device *dev)
+{
+ struct si4455_port *s = dev_get_drvdata(dev);
+
+ cancel_work_sync(&s->one.tx_work);
+ sysfs_remove_group(&dev->kobj, &si4455_attr_group);
+ uart_remove_one_port(&si4455_uart, &s->one.port);
+
+ mutex_destroy(&s->mutex);
+
+ return 0;
+}
+
+static const struct of_device_id __maybe_unused si4455_dt_ids[] = {
+ { .compatible = "silabs,si4455" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, si4455_dt_ids);
+
+static int si4455_spi_probe(struct spi_device *spi)
+{
+ int ret;
+ const struct of_device_id *of_id;
+
+ /* Setup SPI bus */
+ spi->bits_per_word = 8;
+ spi->mode = SPI_MODE_0;
+ ret = spi_setup(spi);
+ if (ret)
+ return ret;
+
+ if (spi->dev.of_node) {
+ of_id = of_match_device(si4455_dt_ids, &spi->dev);
+ if (!of_id)
+ return -ENODEV;
+ }
+
+ return si4455_probe(&spi->dev, spi->irq);
+}
+
+static int si4455_spi_remove(struct spi_device *spi)
+{
+ return si4455_remove(&spi->dev);
+}
+
+static struct spi_driver si4455_spi_driver = {
+ .driver = {
+ .name = SI4455_NAME,
+ .of_match_table = of_match_ptr(si4455_dt_ids),
+ .pm = &si4455_pm_ops,
+ },
+ .probe = si4455_spi_probe,
+ .remove = si4455_spi_remove,
+};
+
+static int __init si4455_uart_init(void)
+{
+ int ret;
+
+ ret = uart_register_driver(&si4455_uart);
+ if (ret)
+ return ret;
+ spi_register_driver(&si4455_spi_driver);
+
+ return 0;
+}
+module_init(si4455_uart_init);
+
+static void __exit si4455_uart_exit(void)
+{
+ spi_unregister_driver(&si4455_spi_driver);
+ uart_unregister_driver(&si4455_uart);
+}
+module_exit(si4455_uart_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("József Horváth <info@ministro.hu>");
+MODULE_DESCRIPTION("Si4455 serial driver");
This is a serial port driver for Silicon Labs Si4455 Sub-GHz transciver. The goal of this driver is to removing wires between central(linux) device and remote serial devices/sensors, but keeping the original user software. It represents regular serial interface for the user space. Datasheet: https://www.silabs.com/documents/public/data-sheets/Si4455.pdf Signed-off-by: József Horváth <info@ministro.hu> --- .../staging/serial/silabs,si4455.yaml | 98 ++ MAINTAINERS | 7 + drivers/tty/serial/Kconfig | 8 + drivers/tty/serial/Makefile | 1 + drivers/tty/serial/si4455.c | 1328 +++++++++++++++++ 5 files changed, 1442 insertions(+) create mode 100644 Documentation/devicetree/bindings/staging/serial/silabs,si4455.yaml create mode 100644 drivers/tty/serial/si4455.c