@@ -14,6 +14,17 @@ config MMC_ARMMMCI
If unsure, say N.
+config MMC_QCOM_DML
+ tristate "Qualcomm Data Mover for SD Card Controller"
+ depends on MMC_ARMMMCI && QCOM_BAM_DMA
+ default y
+ help
+ This selects the Qualcomm Data Mover lite/local on SD Card controller.
+ This option will enable the dma to work correctly, if you are using
+ Qcom SOCs and MMC, you would probably need this option to get DMA working.
+
+ if unsure, say N.
+
config MMC_PXA
tristate "Intel PXA25x/26x/27x Multimedia Card Interface support"
depends on ARCH_PXA
@@ -3,6 +3,7 @@
#
obj-$(CONFIG_MMC_ARMMMCI) += mmci.o
+obj-$(CONFIG_MMC_QCOM_DML) += mmci_qcom_dml.o
obj-$(CONFIG_MMC_PXA) += pxamci.o
obj-$(CONFIG_MMC_MXC) += mxcmmc.o
obj-$(CONFIG_MMC_MXS) += mxs-mmc.o
@@ -43,6 +43,7 @@
#include <asm/sizes.h>
#include "mmci.h"
+#include "mmci_qcom_dml.h"
#define DRIVER_NAME "mmci-pl18x"
@@ -74,6 +75,7 @@ static unsigned int fmax = 515633;
* @pwrreg_nopower: bits in MMCIPOWER don't controls ext. power supply
* @explicit_mclk_control: enable explicit mclk control in driver.
* @qcom_fifo: enables qcom specific fifo pio read logic.
+ * @qcom_dml: enables qcom specific dma glue for dma transfers.
*/
struct variant_data {
unsigned int clkreg;
@@ -97,6 +99,7 @@ struct variant_data {
bool pwrreg_nopower;
bool explicit_mclk_control;
bool qcom_fifo;
+ bool qcom_dml;
};
static struct variant_data variant_arm = {
@@ -205,6 +208,7 @@ static struct variant_data variant_qcom = {
.f_max = 208000000,
.explicit_mclk_control = true,
.qcom_fifo = true,
+ .qcom_dml = true,
};
static int mmci_card_busy(struct mmc_host *mmc)
@@ -418,6 +422,7 @@ static void mmci_dma_setup(struct mmci_host *host)
{
const char *rxname, *txname;
dma_cap_mask_t mask;
+ struct variant_data *variant = host->variant;
host->dma_rx_channel = dma_request_slave_channel(mmc_dev(host->mmc), "rx");
host->dma_tx_channel = dma_request_slave_channel(mmc_dev(host->mmc), "tx");
@@ -468,6 +473,10 @@ static void mmci_dma_setup(struct mmci_host *host)
if (max_seg_size < host->mmc->max_seg_size)
host->mmc->max_seg_size = max_seg_size;
}
+
+ if (variant->qcom_dml && host->dma_rx_channel && host->dma_tx_channel)
+ if (dml_hw_init(host, host->mmc->parent->of_node))
+ variant->qcom_dml = false;
}
/*
@@ -569,6 +578,7 @@ static int __mmci_dma_prep_data(struct mmci_host *host, struct mmc_data *data,
struct dma_async_tx_descriptor *desc;
enum dma_data_direction buffer_dirn;
int nr_sg;
+ unsigned long flags = DMA_CTRL_ACK;
if (data->flags & MMC_DATA_READ) {
conf.direction = DMA_DEV_TO_MEM;
@@ -593,9 +603,12 @@ static int __mmci_dma_prep_data(struct mmci_host *host, struct mmc_data *data,
if (nr_sg == 0)
return -EINVAL;
+ if (host->variant->qcom_dml)
+ flags |= DMA_PREP_INTERRUPT;
+
dmaengine_slave_config(chan, &conf);
desc = dmaengine_prep_slave_sg(chan, data->sg, nr_sg,
- conf.direction, DMA_CTRL_ACK);
+ conf.direction, flags);
if (!desc)
goto unmap_exit;
@@ -644,6 +657,9 @@ static int mmci_dma_start_data(struct mmci_host *host, unsigned int datactrl)
dmaengine_submit(host->dma_desc_current);
dma_async_issue_pending(host->dma_current);
+ if (host->variant->qcom_dml)
+ dml_start_xfer(host, data);
+
datactrl |= MCI_DPSM_DMAENABLE;
/* Trigger the DMA transfer */
new file mode 100644
@@ -0,0 +1,177 @@
+/*
+ *
+ * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+#include <linux/of.h>
+#include <linux/of_dma.h>
+#include <linux/bitops.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/card.h>
+#include "mmci.h"
+
+/* Registers */
+#define DML_CONFIG 0x00
+#define PRODUCER_CRCI_MSK GENMASK(1, 0)
+#define PRODUCER_CRCI_DISABLE 0
+#define PRODUCER_CRCI_X_SEL BIT(0)
+#define PRODUCER_CRCI_Y_SEL BIT(1)
+#define CONSUMER_CRCI_MSK GENMASK(3, 2)
+#define CONSUMER_CRCI_DISABLE 0
+#define CONSUMER_CRCI_X_SEL BIT(2)
+#define CONSUMER_CRCI_Y_SEL BIT(3)
+#define PRODUCER_TRANS_END_EN BIT(4)
+#define BYPASS BIT(16)
+#define DIRECT_MODE BIT(17)
+#define INFINITE_CONS_TRANS BIT(18)
+
+#define DML_SW_RESET 0x08
+#define DML_PRODUCER_START 0x0c
+#define DML_CONSUMER_START 0x10
+#define DML_PRODUCER_PIPE_LOGICAL_SIZE 0x14
+#define DML_CONSUMER_PIPE_LOGICAL_SIZE 0x18
+#define DML_PIPE_ID 0x1c
+#define PRODUCER_PIPE_ID_SHFT 0
+#define PRODUCER_PIPE_ID_MSK GENMASK(4, 0)
+#define CONSUMER_PIPE_ID_SHFT 16
+#define CONSUMER_PIPE_ID_MSK GENMASK(20, 16)
+
+#define DML_PRODUCER_BAM_BLOCK_SIZE 0x24
+#define DML_PRODUCER_BAM_TRANS_SIZE 0x28
+
+/* other definitions */
+#define PRODUCER_PIPE_LOGICAL_SIZE 4096
+#define CONSUMER_PIPE_LOGICAL_SIZE 4096
+
+#define DML_OFFSET 0x800
+
+void dml_start_xfer(struct mmci_host *host, struct mmc_data *data)
+{
+ u32 config;
+ void __iomem *base = host->base + DML_OFFSET;
+
+ if (data->flags & MMC_DATA_READ) {
+ /* Read operation: configure DML for producer operation */
+ /* Set producer CRCI-x and disable consumer CRCI */
+ config = readl_relaxed(base + DML_CONFIG);
+ config = (config & ~PRODUCER_CRCI_MSK) | PRODUCER_CRCI_X_SEL;
+ config = (config & ~CONSUMER_CRCI_MSK) | CONSUMER_CRCI_DISABLE;
+ writel_relaxed(config, base + DML_CONFIG);
+
+ /* Set the Producer BAM block size */
+ writel_relaxed(data->blksz, base + DML_PRODUCER_BAM_BLOCK_SIZE);
+
+ /* Set Producer BAM Transaction size */
+ writel_relaxed(data->blocks * data->blksz,
+ base + DML_PRODUCER_BAM_TRANS_SIZE);
+ /* Set Producer Transaction End bit */
+ config = readl_relaxed(base + DML_CONFIG);
+ config |= PRODUCER_TRANS_END_EN;
+ writel_relaxed(config, base + DML_CONFIG);
+ /* Trigger producer */
+ writel_relaxed(1, base + DML_PRODUCER_START);
+ } else {
+ /* Write operation: configure DML for consumer operation */
+ /* Set consumer CRCI-x and disable producer CRCI*/
+ config = readl_relaxed(base + DML_CONFIG);
+ config = (config & ~CONSUMER_CRCI_MSK) | CONSUMER_CRCI_X_SEL;
+ config = (config & ~PRODUCER_CRCI_MSK) | PRODUCER_CRCI_DISABLE;
+ writel_relaxed(config, base + DML_CONFIG);
+ /* Clear Producer Transaction End bit */
+ config = readl_relaxed(base + DML_CONFIG);
+ config &= ~PRODUCER_TRANS_END_EN;
+ writel_relaxed(config, base + DML_CONFIG);
+ /* Trigger consumer */
+ writel_relaxed(1, base + DML_CONSUMER_START);
+ }
+
+ /* make sure the dml is configured before dma is triggered */
+ wmb();
+}
+
+static int of_get_dml_pipe_index(struct device_node *np, const char *name)
+{
+ int index;
+ struct of_phandle_args dma_spec;
+
+ index = of_property_match_string(np, "dma-names", name);
+
+ if (index < 0)
+ return -ENODEV;
+
+ if (of_parse_phandle_with_args(np, "dmas", "#dma-cells", index,
+ &dma_spec))
+ return -ENODEV;
+
+ if (dma_spec.args_count)
+ return dma_spec.args[0];
+
+ return -ENODEV;
+}
+
+/* Initialize the dml hardware connected to SD Card controller */
+int dml_hw_init(struct mmci_host *host, struct device_node *np)
+{
+ u32 config;
+ void __iomem *base;
+ u32 consumer_id, producer_id;
+
+ consumer_id = of_get_dml_pipe_index(np, "tx");
+ producer_id = of_get_dml_pipe_index(np, "rx");
+
+ if (producer_id < 0 || consumer_id < 0)
+ return -ENODEV;
+
+ base = host->base + DML_OFFSET;
+
+ /* Reset the DML block */
+ writel_relaxed(1, base + DML_SW_RESET);
+
+ /* Disable the producer and consumer CRCI */
+ config = (PRODUCER_CRCI_DISABLE | CONSUMER_CRCI_DISABLE);
+ /*
+ * Disable the bypass mode. Bypass mode will only be used
+ * if data transfer is to happen in PIO mode and don't
+ * want the BAM interface to connect with SDCC-DML.
+ */
+ config &= ~BYPASS;
+ /*
+ * Disable direct mode as we don't DML to MASTER the AHB bus.
+ * BAM connected with DML should MASTER the AHB bus.
+ */
+ config &= ~DIRECT_MODE;
+ /*
+ * Disable infinite mode transfer as we won't be doing any
+ * infinite size data transfers. All data transfer will be
+ * of finite data size.
+ */
+ config &= ~INFINITE_CONS_TRANS;
+ writel_relaxed(config, base + DML_CONFIG);
+
+ /*
+ * Initialize the logical BAM pipe size for producer
+ * and consumer.
+ */
+ writel_relaxed(PRODUCER_PIPE_LOGICAL_SIZE,
+ base + DML_PRODUCER_PIPE_LOGICAL_SIZE);
+ writel_relaxed(CONSUMER_PIPE_LOGICAL_SIZE,
+ base + DML_CONSUMER_PIPE_LOGICAL_SIZE);
+
+ /* Initialize Producer/consumer pipe id */
+ writel_relaxed(producer_id | (consumer_id << CONSUMER_PIPE_ID_SHFT),
+ base + DML_PIPE_ID);
+
+ /* Make sure dml intialization is finished */
+ mb();
+
+ return 0;
+}
new file mode 100644
@@ -0,0 +1,31 @@
+/*
+ *
+ * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+#ifndef __MMC_QCOM_DML_H__
+#define __MMC_QCOM_DML_H__
+
+#ifdef CONFIG_MMC_QCOM_DML
+int dml_hw_init(struct mmci_host *host, struct device_node *np);
+void dml_start_xfer(struct mmci_host *host, struct mmc_data *data);
+#else
+static inline int dml_hw_init(struct mmci_host *host, struct device_node *np)
+{
+ return -ENOSYS;
+}
+static inline void dml_start_xfer(struct mmci_host *host, struct mmc_data *data)
+{
+}
+#endif /* CONFIG_MMC_QCOM_DML */
+
+#endif /* __MMC_QCOM_DML_H__ */