diff mbox series

[2/3] thermal: ti-soc-thermal: Simplify polling with iopoll

Message ID 20201230084338.19410-2-tony@atomide.com
State New
Headers show
Series None | expand

Commit Message

Tony Lindgren Dec. 30, 2020, 8:43 a.m. UTC 
We can use iopoll for checking the EOCZ (end of conversion) bit.

Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 drivers/thermal/ti-soc-thermal/ti-bandgap.c | 30 ++++++++++-----------
 1 file changed, 14 insertions(+), 16 deletions(-)
diff mbox series

Patch

diff --git a/drivers/thermal/ti-soc-thermal/ti-bandgap.c b/drivers/thermal/ti-soc-thermal/ti-bandgap.c
--- a/drivers/thermal/ti-soc-thermal/ti-bandgap.c
+++ b/drivers/thermal/ti-soc-thermal/ti-bandgap.c
@@ -15,7 +15,6 @@ 
 #include <linux/kernel.h>
 #include <linux/interrupt.h>
 #include <linux/clk.h>
-#include <linux/delay.h>
 #include <linux/gpio/consumer.h>
 #include <linux/platform_device.h>
 #include <linux/err.h>
@@ -27,6 +26,7 @@ 
 #include <linux/of_platform.h>
 #include <linux/of_irq.h>
 #include <linux/io.h>
+#include <linux/iopoll.h>
 #include <linux/cpu_pm.h>
 #include <linux/device.h>
 #include <linux/pm_runtime.h>
@@ -603,8 +603,9 @@  void *ti_bandgap_get_sensor_data(struct ti_bandgap *bgp, int id)
 static int
 ti_bandgap_force_single_read(struct ti_bandgap *bgp, int id)
 {
-	u32 counter = 1000;
 	struct temp_sensor_registers *tsr;
+	int error;
+	u32 val;
 
 	/* Select continuous or single conversion mode */
 	if (TI_BANDGAP_HAS(bgp, CONT_MODE_ONLY))
@@ -615,27 +616,24 @@  ti_bandgap_force_single_read(struct ti_bandgap *bgp, int id)
 	/* Start of Conversion = 1 */
 	RMW_BITS(bgp, id, temp_sensor_ctrl, bgap_soc_mask, 1);
 
-	/* Wait for EOCZ going up */
 	tsr = bgp->conf->sensors[id].registers;
 
-	while (--counter) {
-		if (ti_bandgap_readl(bgp, tsr->temp_sensor_ctrl) &
-		    tsr->bgap_eocz_mask)
-			break;
-		udelay(1);
-	}
+	/* Wait for EOCZ going up */
+	error = readl_poll_timeout_atomic(bgp->base + tsr->temp_sensor_ctrl,
+					  val, val & tsr->bgap_eocz_mask,
+					  1, 1000);
+	if (error)
+		dev_warn(bgp->dev, "eocz timed out waiting high\n");
 
 	/* Start of Conversion = 0 */
 	RMW_BITS(bgp, id, temp_sensor_ctrl, bgap_soc_mask, 0);
 
 	/* Wait for EOCZ going down */
-	counter = 1000;
-	while (--counter) {
-		if (!(ti_bandgap_readl(bgp, tsr->temp_sensor_ctrl) &
-		      tsr->bgap_eocz_mask))
-			break;
-		udelay(1);
-	}
+	error = readl_poll_timeout_atomic(bgp->base + tsr->temp_sensor_ctrl,
+					  val, !(val & tsr->bgap_eocz_mask),
+					  1, 1000);
+	if (error)
+		dev_warn(bgp->dev, "eocz timed out waiting low\n");
 
 	return 0;
 }