| Message ID | 1409740079-16554-3-git-send-email-peter.griffin@linaro.org |
|---|---|
| State | New |
| Headers | show |
Hi, On Wednesday 03 September 2014 03:57 PM, Peter Griffin wrote: > This patch adds the dt documentation for the usb picophy found on stih407 SoC family > available from STMicroelectronics. > > Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> > Signed-off-by: Peter Griffin <peter.griffin@linaro.org> > --- > .../devicetree/bindings/phy/phy-stih407-usb.txt | 37 ++++++++++++++++++++++ > 1 file changed, 37 insertions(+) > create mode 100644 Documentation/devicetree/bindings/phy/phy-stih407-usb.txt > > diff --git a/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt > new file mode 100644 > index 0000000..650d346 > --- /dev/null > +++ b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt > @@ -0,0 +1,37 @@ > +ST STiH407 USB-PHY controller > + > +This file documents the dt bindings for the picoPHY driver which is the PHY for both USB2 and USB3 host controllers > +controllers available on STiH407 SoC families. > + > +On STiH410, we have to use the DWC3 port#2 with a picoPHY to manage USB2 > +devices. The USB2 Controller will use the ports #0 and #1. > + > +This is to document the DT parameters to be passed from the blob in that case. > + > +Required properties: > +- compatible : should be "st,stih407-usb2-phy" If STiH410 also uses the same driver then you should add a new compatibility value for it. > +- reg : contain the offset and length of the system configuration registers > + used as glue logic to control & parameter phy > +- reg-names : the names of the system configuration registers in "reg", should be "param" and "reg" > +- st,syscfg : sysconfig register to manage phy parameter at driver level > +- resets : list of phandle and reset specifier pairs. There should be two entries, one > + for the whole phy and one for the port > +- reset-names : list of reset signal names. Should be "global" and "port" > +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt > +See: Documentation/devicetree/bindings/reset/reset.txt > + > +Example: > + > +usb2_picophy0: usbpicophy@0 { usbpicophy@f8 since you have a reg property ;-) > + compatible = "st,stih407-usb2-phy"; > + reg = <0xf8 0x04>, /* syscfg 5062 */ > + <0xf4 0x04>; /* syscfg 5061 */ > + reg-names = "param", > + "ctrl"; > + #phy-cells = <0>; alignment seems to have gone wrong here. Thanks Kishon -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Hi Kishon, Thanks for reviewing :-) > > +On STiH410, we have to use the DWC3 port#2 with a picoPHY to manage USB2 > > +devices. The USB2 Controller will use the ports #0 and #1. > > + > > +This is to document the DT parameters to be passed from the blob in that case. > > + > > +Required properties: > > +- compatible : should be "st,stih407-usb2-phy" > > If STiH410 also uses the same driver then you should add a new compatibility > value for it. I will remove the reference to stih410 in V2, as currently it is not supported upstream, and I'm not sure what ST's plans are regarding upstreaming it. If/ when it is upstreamed, we can add this and a compabible property back in. <snip> > > + > > +usb2_picophy0: usbpicophy@0 { > usbpicophy@f8 since you have a reg property ;-) will fix in V2 > > > + compatible = "st,stih407-usb2-phy"; > > + reg = <0xf8 0x04>, /* syscfg 5062 */ > > + <0xf4 0x04>; /* syscfg 5061 */ > > + reg-names = "param", > > + "ctrl"; > > + #phy-cells = <0>; > > alignment seems to have gone wrong here. Will fix in v2 regards, Peter. -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt new file mode 100644 index 0000000..650d346 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt @@ -0,0 +1,37 @@ +ST STiH407 USB-PHY controller + +This file documents the dt bindings for the picoPHY driver which is the PHY for both USB2 and USB3 host controllers +controllers available on STiH407 SoC families. + +On STiH410, we have to use the DWC3 port#2 with a picoPHY to manage USB2 +devices. The USB2 Controller will use the ports #0 and #1. + +This is to document the DT parameters to be passed from the blob in that case. + +Required properties: +- compatible : should be "st,stih407-usb2-phy" +- reg : contain the offset and length of the system configuration registers + used as glue logic to control & parameter phy +- reg-names : the names of the system configuration registers in "reg", should be "param" and "reg" +- st,syscfg : sysconfig register to manage phy parameter at driver level +- resets : list of phandle and reset specifier pairs. There should be two entries, one + for the whole phy and one for the port +- reset-names : list of reset signal names. Should be "global" and "port" +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt +See: Documentation/devicetree/bindings/reset/reset.txt + +Example: + +usb2_picophy0: usbpicophy@0 { + compatible = "st,stih407-usb2-phy"; + reg = <0xf8 0x04>, /* syscfg 5062 */ + <0xf4 0x04>; /* syscfg 5061 */ + reg-names = "param", + "ctrl"; + #phy-cells = <0>; + st,syscfg = <&syscfg_core>; + resets = <&softreset STIH407_PICOPHY_SOFTRESET>, + <&picophyreset STIH407_PICOPHY0_RESET>; + reset-names = "global", + "port"; +};