| Message ID | 1615250236-11349-1-git-send-email-hayashi.kunihiko@socionext.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [1/2] ARM: dts: uniphier: Change phy-mode to RGMII-ID to enable delay pins for RTL8211E | expand |
Gentle Ping. Are there any comments about these two patches? Thank you, On Tue, 9 Mar 2021 09:37:15 +0900 Kunihiko Hayashi <hayashi.kunihiko@socionext.com> wrote: > After applying the commit bbc4d71d6354 > ("net: phy: realtek: fix rtl8211e rx/tx delay config"), the configuration > register for TXDLY and RXDLY is set correctly. > > Although PXs2 boards have RTL8211E for gigabit network PHY, it turrned out > that the phy-mode should be RGMII-ID mode. This changes 'phy-mode' property > to 'rgmii-id' as default. > > Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> > --- > arch/arm/boot/dts/uniphier-pxs2.dtsi | 2 +- > 1 file changed, 1 insertion(+), 1 deletion(-) > > diff --git a/arch/arm/boot/dts/uniphier-pxs2.dtsi b/arch/arm/boot/dts/uniphier-pxs2.dtsi > index 4d9f69a..5ba831e 100644 > --- a/arch/arm/boot/dts/uniphier-pxs2.dtsi > +++ b/arch/arm/boot/dts/uniphier-pxs2.dtsi > @@ -583,7 +583,7 @@ > clocks = <&sys_clk 6>; > reset-names = "ether"; > resets = <&sys_rst 6>; > - phy-mode = "rgmii"; > + phy-mode = "rgmii-id"; > local-mac-address = [00 00 00 00 00 00]; > socionext,syscon-phy-mode = <&soc_glue 0>; > > -- > 2.7.4 --- Best Regards, Kunihiko Hayashi
diff --git a/arch/arm/boot/dts/uniphier-pxs2.dtsi b/arch/arm/boot/dts/uniphier-pxs2.dtsi index 4d9f69a..5ba831e 100644 --- a/arch/arm/boot/dts/uniphier-pxs2.dtsi +++ b/arch/arm/boot/dts/uniphier-pxs2.dtsi @@ -583,7 +583,7 @@ clocks = <&sys_clk 6>; reset-names = "ether"; resets = <&sys_rst 6>; - phy-mode = "rgmii"; + phy-mode = "rgmii-id"; local-mac-address = [00 00 00 00 00 00]; socionext,syscon-phy-mode = <&soc_glue 0>;
After applying the commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config"), the configuration register for TXDLY and RXDLY is set correctly. Although PXs2 boards have RTL8211E for gigabit network PHY, it turrned out that the phy-mode should be RGMII-ID mode. This changes 'phy-mode' property to 'rgmii-id' as default. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> --- arch/arm/boot/dts/uniphier-pxs2.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) -- 2.7.4