@@ -7,7 +7,7 @@ config NET_VENDOR_FREESCALE
default y
depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
M523x || M527x || M5272 || M528x || M520x || M532x || \
- IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC || \
+ ARCH_MXC || ARCH_MXS || \
(PPC_MPC52xx && PPC_BESTCOMM)
---help---
If you have a network (Ethernet) card belonging to this class, say Y
@@ -16,16 +16,15 @@ config NET_VENDOR_FREESCALE
Note that the answer to this question doesn't directly affect the
kernel: saying N will just cause the configurator to skip all
- the questions about IBM devices. If you say Y, you will be asked for
- your specific card in the following questions.
+ the questions about Freescale devices. If you say Y, you will be
+ asked for your specific card in the following questions.
if NET_VENDOR_FREESCALE
config FEC
bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
- IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC)
- default IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC if ARM
+ ARCH_MXC || ARCH_MXS)
select PHYLIB
---help---
Say Y here if you want to use the built-in 10/100 Fast ethernet
@@ -18,7 +18,7 @@
* Bug fixes and cleanup by Philippe De Muyter (phdm@macqel.be)
* Copyright (c) 2004-2006 Macq Electronique SA.
*
- * Copyright (C) 2010 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
*/
#include <linux/module.h>
@@ -72,6 +72,8 @@
#define FEC_QUIRK_SWAP_FRAME (1 << 1)
/* Controller uses gasket */
#define FEC_QUIRK_USE_GASKET (1 << 2)
+/* Controller has GBIT support */
+#define FEC_QUIRK_HAS_GBIT (1 << 3)
static struct platform_device_id fec_devtype[] = {
{
@@ -88,6 +90,9 @@ static struct platform_device_id fec_devtype[] = {
.name = "imx28-fec",
.driver_data = FEC_QUIRK_ENET_MAC | FEC_QUIRK_SWAP_FRAME,
}, {
+ .name = "imx6q-fec",
+ .driver_data = FEC_QUIRK_ENET_MAC | FEC_QUIRK_HAS_GBIT,
+ }, {
/* sentinel */
}
};
@@ -97,12 +102,14 @@ enum imx_fec_type {
IMX25_FEC = 1, /* runs on i.mx25/50/53 */
IMX27_FEC, /* runs on i.mx27/35/51 */
IMX28_FEC,
+ IMX6Q_FEC,
};
static const struct of_device_id fec_dt_ids[] = {
{ .compatible = "fsl,imx25-fec", .data = &fec_devtype[IMX25_FEC], },
{ .compatible = "fsl,imx27-fec", .data = &fec_devtype[IMX27_FEC], },
{ .compatible = "fsl,imx28-fec", .data = &fec_devtype[IMX28_FEC], },
+ { .compatible = "fsl,imx6q-fec", .data = &fec_devtype[IMX6Q_FEC], },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, fec_dt_ids);
@@ -373,6 +380,7 @@ fec_restart(struct net_device *ndev, int duplex)
int i;
u32 temp_mac[2];
u32 rcntl = OPT_FRAME_SIZE | 0x04;
+ u32 ecntl = 0x2; /* ETHEREN */
/* Whack a reset. We should wait for this. */
writel(1, fep->hwp + FEC_ECNTRL);
@@ -442,18 +450,23 @@ fec_restart(struct net_device *ndev, int duplex)
/* Enable flow control and length check */
rcntl |= 0x40000000 | 0x00000020;
- /* MII or RMII */
- if (fep->phy_interface == PHY_INTERFACE_MODE_RMII)
+ /* RGMII, RMII or MII */
+ if (fep->phy_interface == PHY_INTERFACE_MODE_RGMII)
+ rcntl |= (1 << 6);
+ else if (fep->phy_interface == PHY_INTERFACE_MODE_RMII)
rcntl |= (1 << 8);
else
rcntl &= ~(1 << 8);
- /* 10M or 100M */
- if (fep->phy_dev && fep->phy_dev->speed == SPEED_100)
- rcntl &= ~(1 << 9);
- else
- rcntl |= (1 << 9);
-
+ /* 1G, 100M or 10M */
+ if (fep->phy_dev) {
+ if (fep->phy_dev->speed == SPEED_1000)
+ ecntl |= (1 << 5);
+ else if (fep->phy_dev->speed == SPEED_100)
+ rcntl &= ~(1 << 9);
+ else
+ rcntl |= (1 << 9);
+ }
} else {
#ifdef FEC_MIIGSK_ENR
if (id_entry->driver_data & FEC_QUIRK_USE_GASKET) {
@@ -478,8 +491,15 @@ fec_restart(struct net_device *ndev, int duplex)
}
writel(rcntl, fep->hwp + FEC_R_CNTRL);
+ if (id_entry->driver_data & FEC_QUIRK_ENET_MAC) {
+ /* enable ENET endian swap */
+ ecntl |= (1 << 8);
+ /* enable ENET store and forward mode */
+ writel(1 << 8, fep->hwp + FEC_X_WMRK);
+ }
+
/* And last, enable the transmit and receive processing */
- writel(2, fep->hwp + FEC_ECNTRL);
+ writel(ecntl, fep->hwp + FEC_ECNTRL);
writel(0, fep->hwp + FEC_R_DES_ACTIVE);
/* Enable interrupts we wish to service */
@@ -490,6 +510,8 @@ static void
fec_stop(struct net_device *ndev)
{
struct fec_enet_private *fep = netdev_priv(ndev);
+ const struct platform_device_id *id_entry =
+ platform_get_device_id(fep->pdev);
/* We cannot expect a graceful transmit stop without link !!! */
if (fep->link) {
@@ -504,6 +526,10 @@ fec_stop(struct net_device *ndev)
udelay(10);
writel(fep->phy_speed, fep->hwp + FEC_MII_SPEED);
writel(FEC_DEFAULT_IMASK, fep->hwp + FEC_IMASK);
+
+ /* We have to keep ENET enabled to have MII interrupt stay working */
+ if (id_entry->driver_data & FEC_QUIRK_ENET_MAC)
+ writel(2, fep->hwp + FEC_ECNTRL);
}
@@ -918,6 +944,8 @@ static int fec_enet_mdio_reset(struct mii_bus *bus)
static int fec_enet_mii_probe(struct net_device *ndev)
{
struct fec_enet_private *fep = netdev_priv(ndev);
+ const struct platform_device_id *id_entry =
+ platform_get_device_id(fep->pdev);
struct phy_device *phy_dev = NULL;
char mdio_bus_id[MII_BUS_ID_SIZE];
char phy_name[MII_BUS_ID_SIZE + 3];
@@ -949,14 +977,18 @@ static int fec_enet_mii_probe(struct net_device *ndev)
snprintf(phy_name, MII_BUS_ID_SIZE, PHY_ID_FMT, mdio_bus_id, phy_id);
phy_dev = phy_connect(ndev, phy_name, &fec_enet_adjust_link, 0,
- PHY_INTERFACE_MODE_MII);
+ fep->phy_interface);
if (IS_ERR(phy_dev)) {
printk(KERN_ERR "%s: could not attach to PHY\n", ndev->name);
return PTR_ERR(phy_dev);
}
/* mask with MAC supported features */
- phy_dev->supported &= PHY_BASIC_FEATURES;
+ if (id_entry->driver_data & FEC_QUIRK_HAS_GBIT)
+ phy_dev->supported &= PHY_GBIT_FEATURES;
+ else
+ phy_dev->supported &= PHY_BASIC_FEATURES;
+
phy_dev->advertising = phy_dev->supported;
fep->phy_dev = phy_dev;
@@ -1006,8 +1038,16 @@ static int fec_enet_mii_init(struct platform_device *pdev)
/*
* Set MII speed to 2.5 MHz (= clk_get_rate() / 2 * phy_speed)
+ *
+ * The formula for FEC MDC is 'ref_freq / (MII_SPEED x 2)' while
+ * for ENET-MAC is 'ref_freq / ((MII_SPEED + 1) x 2)'. The i.MX28
+ * Reference Manual has an error on this, and gets fixed on i.MX6Q
+ * document.
*/
- fep->phy_speed = DIV_ROUND_UP(clk_get_rate(fep->clk), 5000000) << 1;
+ fep->phy_speed = DIV_ROUND_UP(clk_get_rate(fep->clk), 5000000);
+ if (id_entry->driver_data & FEC_QUIRK_ENET_MAC)
+ fep->phy_speed--;
+ fep->phy_speed <<= 1;
writel(fep->phy_speed, fep->hwp + FEC_MII_SPEED);
fep->mii_bus = mdiobus_alloc();
The imx6q enet is a derivative of imx28 enet controller. It fixed the frame endian issue found on imx28, and added 1 Gbps support. It also fixes a typo on vendor name in Kconfig. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> --- drivers/net/ethernet/freescale/Kconfig | 9 ++-- drivers/net/ethernet/freescale/fec.c | 66 +++++++++++++++++++++++++------ 2 files changed, 57 insertions(+), 18 deletions(-)