@@ -54,6 +54,7 @@ static unsigned int fmax = 515633;
* @blksz_datactrl16: true if Block size is at b16..b30 position in datactrl register
* @non_power_of_2_blksize: true if block sizes can be other than power of two
* @pwrreg_powerup: power up value for MMCIPOWER register
+ * @signal_direction: input/out direction of bus signals can be indicated
*/
struct variant_data {
unsigned int clkreg;
@@ -66,6 +67,7 @@ struct variant_data {
bool blksz_datactrl16;
bool non_power_of_2_blksize;
unsigned int pwrreg_powerup;
+ bool signal_direction;
};
static struct variant_data variant_arm = {
@@ -89,6 +91,7 @@ static struct variant_data variant_u300 = {
.datalength_bits = 16,
.sdio = true,
.pwrreg_powerup = MCI_PWR_ON,
+ .signal_direction = true,
};
static struct variant_data variant_ux500 = {
@@ -100,6 +103,7 @@ static struct variant_data variant_ux500 = {
.sdio = true,
.st_clkdiv = true,
.pwrreg_powerup = MCI_PWR_ON,
+ .signal_direction = true,
};
static struct variant_data variant_ux500v2 = {
@@ -113,6 +117,7 @@ static struct variant_data variant_ux500v2 = {
.blksz_datactrl16 = true,
.non_power_of_2_blksize = true,
.pwrreg_powerup = MCI_PWR_ON,
+ .signal_direction = true,
};
/*
@@ -1078,6 +1083,22 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
break;
}
+ if (variant->signal_direction && ios->power_mode != MMC_POWER_OFF) {
+ /*
+ * The ST Micro variant has some additional bits
+ * indicating signal direction for the signals in
+ * the SD/MMC bus and feedback-clock usage.
+ */
+ pwr |= host->plat->sigdir;
+
+ if (ios->bus_width == MMC_BUS_WIDTH_4)
+ pwr &= ~MCI_ST_DATA74DIREN;
+ else if (ios->bus_width == MMC_BUS_WIDTH_1)
+ pwr &= (~MCI_ST_DATA74DIREN &
+ ~MCI_ST_DATA31DIREN &
+ ~MCI_ST_DATA2DIREN);
+ }
+
if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN) {
if (host->hw_designer != AMBA_VENDOR_ST)
pwr |= MCI_ROD;
@@ -13,16 +13,6 @@
#define MCI_PWR_ON 0x03
#define MCI_OD (1 << 6)
#define MCI_ROD (1 << 7)
-/*
- * The ST Micro version does not have ROD and reuse the voltage registers
- * for direction settings
- */
-#define MCI_ST_DATA2DIREN (1 << 2)
-#define MCI_ST_CMDDIREN (1 << 3)
-#define MCI_ST_DATA0DIREN (1 << 4)
-#define MCI_ST_DATA31DIREN (1 << 5)
-#define MCI_ST_FBCLKEN (1 << 7)
-#define MCI_ST_DATA74DIREN (1 << 8)
#define MMCICLOCK 0x004
#define MCI_CLK_ENABLE (1 << 8)
@@ -6,6 +6,19 @@
#include <linux/mmc/host.h>
+
+/*
+ * These defines is places here due to access is needed from machine
+ * configuration files. The ST Micro version does not have ROD and
+ * reuse the voltage registers for direction settings.
+ */
+#define MCI_ST_DATA2DIREN (1 << 2)
+#define MCI_ST_CMDDIREN (1 << 3)
+#define MCI_ST_DATA0DIREN (1 << 4)
+#define MCI_ST_DATA31DIREN (1 << 5)
+#define MCI_ST_FBCLKEN (1 << 7)
+#define MCI_ST_DATA74DIREN (1 << 8)
+
/* Just some dummy forwarding */
struct dma_chan;
@@ -30,6 +43,8 @@ struct dma_chan;
* @cd_invert: true if the gpio_cd pin value is active low
* @capabilities: the capabilities of the block as implemented in
* this platform, signify anything MMC_CAP_* from mmc/host.h
+ * @sigdir: a bit field indicating for what bits in the MMC bus the host
+ * should enable signal direction indication.
* @dma_filter: function used to select an appropriate RX and TX
* DMA channel to be used for DMA, if and only if you're deploying the
* generic DMA engine
@@ -52,6 +67,7 @@ struct mmci_platform_data {
int gpio_cd;
bool cd_invert;
unsigned long capabilities;
+ unsigned int sigdir;
bool (*dma_filter)(struct dma_chan *chan, void *filter_param);
void *dma_rx_param;
void *dma_tx_param;