@@ -777,6 +777,68 @@ qca8k_setup_mdio_bus(struct qca8k_priv *priv)
return 0;
}
+static int
+qca8k_setup_of_rgmii_delay(struct qca8k_priv *priv)
+{
+ struct device_node *port_dn;
+ phy_interface_t mode;
+ struct dsa_port *dp;
+ u32 val;
+
+ /* CPU port is already checked */
+ dp = dsa_to_port(priv->ds, 0);
+
+ port_dn = dp->dn;
+
+ /* Check if port 0 is set to the correct type */
+ of_get_phy_mode(port_dn, &mode);
+ if (mode != PHY_INTERFACE_MODE_RGMII_ID &&
+ mode != PHY_INTERFACE_MODE_RGMII_RXID &&
+ mode != PHY_INTERFACE_MODE_RGMII_TXID) {
+ return 0;
+ }
+
+ switch (mode) {
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ if (of_property_read_u32(port_dn, "rx-internal-delay-ps", &val))
+ val = 2;
+ else
+ /* Switch regs accept value in ns, convert ps to ns */
+ val = val / 1000;
+
+ if (val > QCA8K_MAX_DELAY) {
+ dev_err(priv->dev, "rgmii rx delay is limited to a max value of 3ns, setting to the max value");
+ val = 3;
+ }
+
+ priv->rgmii_rx_delay = val;
+ /* Stop here if we need to check only for rx delay */
+ if (mode != PHY_INTERFACE_MODE_RGMII_ID)
+ break;
+
+ fallthrough;
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ if (of_property_read_u32(port_dn, "tx-internal-delay-ps", &val))
+ val = 1;
+ else
+ /* Switch regs accept value in ns, convert ps to ns */
+ val = val / 1000;
+
+ if (val > QCA8K_MAX_DELAY) {
+ dev_err(priv->dev, "rgmii tx delay is limited to a max value of 3ns, setting to the max value");
+ val = 3;
+ }
+
+ priv->rgmii_tx_delay = val;
+ break;
+ default:
+ return 0;
+ }
+
+ return 0;
+}
+
static int
qca8k_setup(struct dsa_switch *ds)
{
@@ -802,6 +864,10 @@ qca8k_setup(struct dsa_switch *ds)
if (ret)
return ret;
+ ret = qca8k_setup_of_rgmii_delay(priv);
+ if (ret)
+ return ret;
+
/* Enable CPU Port */
ret = qca8k_reg_set(priv, QCA8K_REG_GLOBAL_FW_CTRL0,
QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN);
@@ -970,6 +1036,8 @@ qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
case 0: /* 1st CPU port */
if (state->interface != PHY_INTERFACE_MODE_RGMII &&
state->interface != PHY_INTERFACE_MODE_RGMII_ID &&
+ state->interface != PHY_INTERFACE_MODE_RGMII_TXID &&
+ state->interface != PHY_INTERFACE_MODE_RGMII_RXID &&
state->interface != PHY_INTERFACE_MODE_SGMII)
return;
@@ -985,6 +1053,8 @@ qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
case 6: /* 2nd CPU port / external PHY */
if (state->interface != PHY_INTERFACE_MODE_RGMII &&
state->interface != PHY_INTERFACE_MODE_RGMII_ID &&
+ state->interface != PHY_INTERFACE_MODE_RGMII_TXID &&
+ state->interface != PHY_INTERFACE_MODE_RGMII_RXID &&
state->interface != PHY_INTERFACE_MODE_SGMII &&
state->interface != PHY_INTERFACE_MODE_1000BASEX)
return;
@@ -1008,14 +1078,18 @@ qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
qca8k_write(priv, reg, QCA8K_PORT_PAD_RGMII_EN);
break;
case PHY_INTERFACE_MODE_RGMII_ID:
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
/* RGMII_ID needs internal delay. This is enabled through
* PORT5_PAD_CTRL for all ports, rather than individual port
* registers
*/
qca8k_write(priv, reg,
QCA8K_PORT_PAD_RGMII_EN |
- QCA8K_PORT_PAD_RGMII_TX_DELAY(QCA8K_MAX_DELAY) |
- QCA8K_PORT_PAD_RGMII_RX_DELAY(QCA8K_MAX_DELAY));
+ QCA8K_PORT_PAD_RGMII_TX_DELAY(priv->rgmii_tx_delay) |
+ QCA8K_PORT_PAD_RGMII_RX_DELAY(priv->rgmii_rx_delay) |
+ QCA8K_PORT_PAD_RGMII_TX_DELAY_EN |
+ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN);
/* QCA8337 requires to set rgmii rx delay */
if (priv->switch_id == QCA8K_ID_QCA8337)
qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL,
@@ -1073,6 +1147,8 @@ qca8k_phylink_validate(struct dsa_switch *ds, int port,
if (state->interface != PHY_INTERFACE_MODE_NA &&
state->interface != PHY_INTERFACE_MODE_RGMII &&
state->interface != PHY_INTERFACE_MODE_RGMII_ID &&
+ state->interface != PHY_INTERFACE_MODE_RGMII_TXID &&
+ state->interface != PHY_INTERFACE_MODE_RGMII_RXID &&
state->interface != PHY_INTERFACE_MODE_SGMII)
goto unsupported;
break;
@@ -1090,6 +1166,8 @@ qca8k_phylink_validate(struct dsa_switch *ds, int port,
if (state->interface != PHY_INTERFACE_MODE_NA &&
state->interface != PHY_INTERFACE_MODE_RGMII &&
state->interface != PHY_INTERFACE_MODE_RGMII_ID &&
+ state->interface != PHY_INTERFACE_MODE_RGMII_TXID &&
+ state->interface != PHY_INTERFACE_MODE_RGMII_RXID &&
state->interface != PHY_INTERFACE_MODE_SGMII &&
state->interface != PHY_INTERFACE_MODE_1000BASEX)
goto unsupported;
@@ -38,12 +38,11 @@
#define QCA8K_REG_PORT5_PAD_CTRL 0x008
#define QCA8K_REG_PORT6_PAD_CTRL 0x00c
#define QCA8K_PORT_PAD_RGMII_EN BIT(26)
-#define QCA8K_PORT_PAD_RGMII_TX_DELAY(x) \
- ((0x8 + (x & 0x3)) << 22)
-#define QCA8K_PORT_PAD_RGMII_RX_DELAY(x) \
- ((0x10 + (x & 0x3)) << 20)
-#define QCA8K_MAX_DELAY 3
+#define QCA8K_PORT_PAD_RGMII_TX_DELAY(x) ((x) << 22)
+#define QCA8K_PORT_PAD_RGMII_RX_DELAY(x) ((x) << 20)
+#define QCA8K_PORT_PAD_RGMII_TX_DELAY_EN BIT(25)
#define QCA8K_PORT_PAD_RGMII_RX_DELAY_EN BIT(24)
+#define QCA8K_MAX_DELAY 3
#define QCA8K_PORT_PAD_SGMII_EN BIT(7)
#define QCA8K_REG_PWS 0x010
#define QCA8K_PWS_SERDES_AEN_DIS BIT(7)
@@ -254,6 +253,8 @@ struct qca8k_match_data {
struct qca8k_priv {
u8 switch_id;
u8 switch_revision;
+ u8 rgmii_tx_delay;
+ u8 rgmii_rx_delay;
struct regmap *regmap;
struct mii_bus *bus;
struct ar8xxx_port_status port_sts[QCA8K_NUM_PORTS];
The legacy qsdk code used a different delay instead of the max value. Qsdk use 1 ns for rx and 2 ns for tx. Make these values configurable using the standard rx/tx-internal-delay-ps ethernet binding and apply qsdk values by default. The connected gmac doesn't add any delay so no additional delay is added to tx/rx. On this switch the delay is actually in ns so value should be in the 1000 order. Any value converted from ps to ns by dividing it by 1000 as the switch max value for delay is 3ns. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> --- drivers/net/dsa/qca8k.c | 82 ++++++++++++++++++++++++++++++++++++++++- drivers/net/dsa/qca8k.h | 11 +++--- 2 files changed, 86 insertions(+), 7 deletions(-)