@@ -435,12 +435,153 @@ &dcan1 {
status = "okay";
};
+&gpio0 {
+ gpio-line-names =
+ "UART3_CTS", /* M17 */
+ "UART3_RTS", /* M18 */
+ "UART2_RX", /* A17 */
+ "UART2_TX", /* B17 */
+ "I2C1_SDA", /* B16 */
+ "I2C1_SCL", /* A16 */
+ "MMC0_CD", /* C15 */
+ "SPI1_SS2", /* C18 */
+ "EQEP_2A", /* V2 */
+ "EQEP_2B", /* V3 */
+ "MDIR_2B", /* V4 */
+ "BATT_LED_2", /* T5 */
+ "I2C2_SDA", /* D18 */
+ "I2C2_SCL", /* D17 */
+ "UART1_RX", /* D16 */
+ "UART1_TX", /* D15 */
+ "MMC2_DAT1", /* J18 */
+ "MMC2_DAT2", /* K15 */
+ "NC", /* F16 */
+ "WIFI_LED", /* A15 */
+ "MOT_STBY", /* D14 */
+ "WLAN_IRQ", /* K16 */
+ "PWM_2A", /* U10 */
+ "PWM_2B", /* T10 */
+ "",
+ "",
+ "BATT_LED_4", /* T11 */
+ "BATT_LED_1", /* U12 */
+ "BT_EN", /* K17 */
+ "SPI1_SS1", /* H18 */
+ "UART4_RX", /* T17 */
+ "MDIR_1B"; /* U17 */
+};
+
+&gpio1 {
+ gpio-line-names =
+ "MMC1_DAT0", /* U7 */
+ "MMC1_DAT1", /* V7 */
+ "MMC1_DAT2", /* R8 */
+ "MMC1_DAT3", /* T8 */
+ "MMC1_DAT4", /* U8 */
+ "MMC1_DAT5", /* V8 */
+ "MMC1_DAT6", /* R9 */
+ "MMC1_DAT7", /* T9 */
+ "DCAN1_TX", /* E18 */
+ "DCAN1_RX", /* E17 */
+ "UART0_RX", /* E15 */
+ "UART0_TX", /* E16 */
+ "EQEP_3A", /* T12 */
+ "EQEP_3B", /* R12 */
+ "PRU_E_A", /* V13 */
+ "PRU_E_B", /* U13 */
+ "MDIR_2A", /* R13 */
+ "GPIO1_17", /* V14 */
+ "PWM_1A", /* U14 */
+ "PWM_1B", /* T14 */
+ "EMMC_RST", /* R14 */
+ "USR_LED_0", /* V15 */
+ "USR_LED_1", /* U15 */
+ "USR_LED_2", /* T15 */
+ "USR_LED_3", /* V16 */
+ "GPIO1_25", /* U16 */
+ "MCASP0_AXR0", /* T16 */
+ "MCASP0_AXR1", /* V17 */
+ "MCASP0_ACLKR", /* U18 */
+ "BATT_LED_3", /* V6 */
+ "MMC1_CLK", /* U9 */
+ "MMC1_CMD"; /* V9 */
+};
+
+&gpio2 {
+ gpio-line-names =
+ "MDIR_1A", /* T13 */
+ "MCASP0_FSR", /* V12 */
+ "LED_RED", /* R7 */
+ "LED_GREEN", /* T7 */
+ "MODE_BTN", /* U6 */
+ "PAUSE_BTN", /* T6 */
+ "MDIR_4A", /* R1 */
+ "MDIR_4B", /* R2 */
+ "MDIR_3B", /* R3 */
+ "MDIR_3A", /* R4 */
+ "SVO7", /* T1 */
+ "SVO8", /* T2 */
+ "SVO5", /* T3 */
+ "SVO6", /* T4 */
+ "UART5_TX", /* U1 */
+ "UART5_RX", /* U2 */
+ "SERVO_EN", /* U3 */
+ "NC", /* U4 */
+ "UART3_RX", /* L17 */
+ "UART3_TX", /* L16 */
+ "MMC2_CLK", /* L15 */
+ "DCAN1_SILENT", /* M16 */
+ "SVO1", /* U5 */
+ "SVO3", /* R5 */
+ "SVO2", /* V5 */
+ "SVO4", /* R6 */
+ "MMC0_DAT3", /* F17 */
+ "MMC0_DAT2", /* F18 */
+ "MMC0_DAT1", /* G15 */
+ "MMC0_DAT0", /* G16 */
+ "MMC0_CLK", /* G17 */
+ "MMC0_CMD"; /* G18 */
+};
+
&gpio3 {
+ gpio-line-names =
+ "MMC2_DAT3", /* H16 */
+ "GPIO3_1", /* H17 */
+ "GPIO3_2", /* J15 */
+ "MMC2_CMD", /* J16 */
+ "MMC2_DAT0", /* J17 */
+ "I2C0_SDA", /* C17 */
+ "I2C0_SCL", /* C16 */
+ "EMU1", /* C14 */
+ "EMU0", /* B14 */
+ "WL_EN", /* K18 */
+ "WL_BT_OE", /* L18 */
+ "",
+ "",
+ "NC", /* F15 */
+ "SPI1_SCK", /* A13 */
+ "SPI1_MISO", /* B13 */
+ "SPI1_MOSI", /* D12 */
+ "GPIO3_17", /* C12 */
+ "EQEP_0A", /* B12 */
+ "EQEP_0B", /* C13 */
+ "GPIO3_20", /* D13 */
+ "IMU_INT", /* A14 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "";
+
ls_buf_en {
gpio-hog;
gpios = <10 GPIO_ACTIVE_HIGH>;
output-high;
- line-name = "LS_BUF_EN";
};
};
This adds gpio-line-names to the BeagleBone Blue DTS. The line names are based on the BeagleBone Blue rev A2 schematic. Signed-off-by: David Lechner <david@lechnology.com> --- arch/arm/boot/dts/am335x-boneblue.dts | 143 +++++++++++++++++++++++++- 1 file changed, 142 insertions(+), 1 deletion(-)