@@ -142,6 +142,8 @@
#define MPT_MAX_CALLBACKS 32
+#define MPT_MAX_HBA_NUM_PHYS 32
+
#define INTERNAL_CMDS_COUNT 10 /* reserved cmds */
/* reserved for issuing internally framed scsi io cmds */
#define INTERNAL_SCSIIO_CMDS_COUNT 3
@@ -798,6 +800,7 @@ struct _sas_phy {
* @enclosure_handle: handle for this a member of an enclosure
* @device_info: bitwise defining capabilities of this sas_host/expander
* @responding: used in _scsih_expander_device_mark_responding
+ * @nr_phys_allocated: Allocated memory for this many count phys
* @phy: a list of phys that make up this sas_host/expander
* @sas_port_list: list of ports attached to this sas_host/expander
* @port: hba port entry containing node's port number info
@@ -813,6 +816,7 @@ struct _sas_node {
u16 enclosure_handle;
u64 enclosure_logical_id;
u8 responding;
+ u8 nr_phys_allocated;
struct hba_port *port;
struct _sas_phy *phy;
struct list_head sas_port_list;
@@ -6406,11 +6406,26 @@ _scsih_sas_port_refresh(struct MPT3SAS_ADAPTER *ioc)
int i, j, count = 0, lcount = 0;
int ret;
u64 sas_addr;
+ u8 num_phys;
drsprintk(ioc, ioc_info(ioc,
"updating ports for sas_host(0x%016llx)\n",
(unsigned long long)ioc->sas_hba.sas_address));
+ mpt3sas_config_get_number_hba_phys(ioc, &num_phys);
+ if (!num_phys) {
+ ioc_err(ioc, "failure at %s:%d/%s()!\n",
+ __FILE__, __LINE__, __func__);
+ return;
+ }
+
+ if (num_phys > ioc->sas_hba.nr_phys_allocated) {
+ ioc_err(ioc, "failure at %s:%d/%s()!\n",
+ __FILE__, __LINE__, __func__);
+ return;
+ }
+ ioc->sas_hba.num_phys = num_phys;
+
port_table = kcalloc(ioc->sas_hba.num_phys,
sizeof(struct hba_port), GFP_KERNEL);
if (!port_table)
@@ -6611,6 +6626,30 @@ _scsih_sas_host_refresh(struct MPT3SAS_ADAPTER *ioc)
ioc->sas_hba.phy[i].hba_vphy = 1;
}
+ /*
+ * Add new HBA phys to STL if these new phys got added as part
+ * of HBA Firmware upgrade/downgrade operation.
+ */
+ if (!ioc->sas_hba.phy[i].phy) {
+ if ((mpt3sas_config_get_phy_pg0(ioc, &mpi_reply,
+ &phy_pg0, i))) {
+ ioc_err(ioc, "failure at %s:%d/%s()!\n",
+ __FILE__, __LINE__, __func__);
+ continue;
+ }
+ ioc_status = le16_to_cpu(mpi_reply.IOCStatus) &
+ MPI2_IOCSTATUS_MASK;
+ if (ioc_status != MPI2_IOCSTATUS_SUCCESS) {
+ ioc_err(ioc, "failure at %s:%d/%s()!\n",
+ __FILE__, __LINE__, __func__);
+ continue;
+ }
+ ioc->sas_hba.phy[i].phy_id = i;
+ mpt3sas_transport_add_host_phy(ioc,
+ &ioc->sas_hba.phy[i], phy_pg0,
+ ioc->sas_hba.parent_dev);
+ continue;
+ }
ioc->sas_hba.phy[i].handle = ioc->sas_hba.handle;
attached_handle = le16_to_cpu(sas_iounit_pg0->PhyData[i].
AttachedDevHandle);
@@ -6622,6 +6661,19 @@ _scsih_sas_host_refresh(struct MPT3SAS_ADAPTER *ioc)
attached_handle, i, link_rate,
ioc->sas_hba.phy[i].port);
}
+ /*
+ * Clear the phy details if this phy got disabled as part of
+ * HBA Firmware upgrade/downgrade operation.
+ */
+ for (i = ioc->sas_hba.num_phys;
+ i < ioc->sas_hba.nr_phys_allocated; i++) {
+ if (ioc->sas_hba.phy[i].phy &&
+ ioc->sas_hba.phy[i].phy->negotiated_linkrate >=
+ SAS_LINK_RATE_1_5_GBPS)
+ mpt3sas_transport_update_links(ioc,
+ ioc->sas_hba.sas_address, 0, i,
+ MPI2_SAS_NEG_LINK_RATE_PHY_DISABLED, NULL);
+ }
out:
kfree(sas_iounit_pg0);
}
@@ -6654,7 +6706,10 @@ _scsih_sas_host_add(struct MPT3SAS_ADAPTER *ioc)
__FILE__, __LINE__, __func__);
return;
}
- ioc->sas_hba.phy = kcalloc(num_phys,
+
+ ioc->sas_hba.nr_phys_allocated = max_t(u8,
+ MPT_MAX_HBA_NUM_PHYS, num_phys);
+ ioc->sas_hba.phy = kcalloc(ioc->sas_hba.nr_phys_allocated,
sizeof(struct _sas_phy), GFP_KERNEL);
if (!ioc->sas_hba.phy) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
While determining the SAS address of a drive, the driver checks whether the handle number is less than the HBA phys count or not. If the handle number is less than the HBA phy’s count then driver assumes that this handle belongs to HBA and hence it assigns the HBA SAS address. During IOC firmware downgrade operation, if the number of HBA phys got reduced and the OS drive’s device handle falls below start of the day HBA phys count then while determining the OS drive’s SAS address driver uses the HBA SAS address. This leads to a mismatch of drive’s SAS address and hence the driver unregisters the OS drive and the system falls into read only mode. Updated the IOC's num_phys to HBA phy’s count provided by actual loaded firmware. So that while determining the SAS address driver uses updated HBA phy’s count value instead of using a start of the day’s HBA phy’s count. Fixes: a5e99fda0172("mpt3sas: Update hba_port objects after host reset") Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> --- drivers/scsi/mpt3sas/mpt3sas_base.h | 4 ++ drivers/scsi/mpt3sas/mpt3sas_scsih.c | 57 +++++++++++++++++++++++++++- 2 files changed, 60 insertions(+), 1 deletion(-)