@@ -17,7 +17,6 @@
#include <linux/pinctrl/consumer.h>
#include <linux/platform_device.h>
#include <linux/of.h>
-#include <linux/of_gpio.h>
#include <linux/of_irq.h>
#include <linux/pm_runtime.h>
#include <linux/spi/spi.h>
@@ -171,11 +170,6 @@ static int spi_st_transfer_one(struct spi_master *master,
return t->len;
}
-static void spi_st_cleanup(struct spi_device *spi)
-{
- gpio_free(spi->cs_gpio);
-}
-
/* the spi->mode bits understood by this driver: */
#define MODEBITS (SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST | SPI_LOOP | SPI_CS_HIGH)
static int spi_st_setup(struct spi_device *spi)
@@ -183,29 +177,17 @@ static int spi_st_setup(struct spi_device *spi)
struct spi_st *spi_st = spi_master_get_devdata(spi->master);
u32 spi_st_clk, sscbrg, var;
u32 hz = spi->max_speed_hz;
- int cs = spi->cs_gpio;
- int ret;
if (!hz) {
dev_err(&spi->dev, "max_speed_hz unspecified\n");
return -EINVAL;
}
- if (!gpio_is_valid(cs)) {
- dev_err(&spi->dev, "%d is not a valid gpio\n", cs);
+ if (!spi->cs_gpiod) {
+ dev_err(&spi->dev, "no valid gpio assigned\n");
return -EINVAL;
}
- ret = gpio_request(cs, dev_name(&spi->dev));
- if (ret) {
- dev_err(&spi->dev, "could not request gpio:%d\n", cs);
- return ret;
- }
-
- ret = gpio_direction_output(cs, spi->mode & SPI_CS_HIGH);
- if (ret)
- goto out_free_gpio;
-
spi_st_clk = clk_get_rate(spi_st->clk);
/* Set SSC_BRF */
@@ -213,8 +195,7 @@ static int spi_st_setup(struct spi_device *spi)
if (sscbrg < 0x07 || sscbrg > BIT(16)) {
dev_err(&spi->dev,
"baudrate %d outside valid range %d\n", sscbrg, hz);
- ret = -EINVAL;
- goto out_free_gpio;
+ return -EINVAL;
}
spi_st->baud = spi_st_clk / (2 * sscbrg);
@@ -263,10 +244,6 @@ static int spi_st_setup(struct spi_device *spi)
readl_relaxed(spi_st->base + SSC_RBUF);
return 0;
-
-out_free_gpio:
- gpio_free(cs);
- return ret;
}
/* Interrupt fired when TX shift register becomes empty */
@@ -309,11 +286,11 @@ static int spi_st_probe(struct platform_device *pdev)
master->dev.of_node = np;
master->mode_bits = MODEBITS;
master->setup = spi_st_setup;
- master->cleanup = spi_st_cleanup;
master->transfer_one = spi_st_transfer_one;
master->bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(16);
master->auto_runtime_pm = true;
master->bus_num = pdev->id;
+ master->use_gpio_descriptors = true;
spi_st = spi_master_get_devdata(master);
spi_st->clk = devm_clk_get(&pdev->dev, "ssc");
This switches the ST SSC SPI controller to use GPIO descriptors from the core instead of GPIO numbers. It is already using the core parsing of GPIO numbers so the switch is pretty straight-forward. Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- ChangeLog v1->v2: - Get rid of a dangling "ret" variable causing build noise. --- drivers/spi/spi-st-ssc4.c | 31 ++++--------------------------- 1 file changed, 4 insertions(+), 27 deletions(-)