@@ -2,19 +2,33 @@
/* Synopsys DesignWare 8250 library. */
#include <linux/bitops.h>
+#include <linux/bitfield.h>
#include <linux/device.h>
#include <linux/io.h>
#include <linux/kernel.h>
+#include <linux/property.h>
#include <linux/serial_8250.h>
#include <linux/serial_core.h>
#include "8250_dwlib.h"
/* Offsets for the DesignWare specific registers */
+#define DW_UART_TCR 0xac /* Transceiver Control Register (RS485) */
+#define DW_UART_DE_EN 0xb0 /* Driver Output Enable Register */
+#define DW_UART_RE_EN 0xb4 /* Receiver Output Enable Register */
#define DW_UART_DLF 0xc0 /* Divisor Latch Fraction Register */
#define DW_UART_CPR 0xf4 /* Component Parameter Register */
#define DW_UART_UCV 0xf8 /* UART Component Version */
+/* Transceiver Control Register bits */
+#define DW_UART_TCR_RS485_EN BIT(0)
+#define DW_UART_TCR_RE_POL BIT(1)
+#define DW_UART_TCR_DE_POL BIT(2)
+#define DW_UART_TCR_XFER_MODE GENMASK(4, 3)
+#define DW_UART_TCR_XFER_MODE_DE_DURING_RE FIELD_PREP(DW_UART_TCR_XFER_MODE, 0)
+#define DW_UART_TCR_XFER_MODE_SW_DE_OR_RE FIELD_PREP(DW_UART_TCR_XFER_MODE, 1)
+#define DW_UART_TCR_XFER_MODE_DE_OR_RE FIELD_PREP(DW_UART_TCR_XFER_MODE, 2)
+
/* Component Parameter Register bits */
#define DW_UART_CPR_ABP_DATA_WIDTH (3 << 0)
#define DW_UART_CPR_AFCE_MODE (1 << 4)
@@ -87,11 +101,80 @@ void dw8250_do_set_termios(struct uart_port *p, struct ktermios *termios, struct
}
EXPORT_SYMBOL_GPL(dw8250_do_set_termios);
+static int dw8250_rs485_config(struct uart_port *p, struct serial_rs485 *rs485)
+{
+ u32 tcr;
+
+ tcr = dw8250_readl_ext(p, DW_UART_TCR);
+ tcr &= ~DW_UART_TCR_XFER_MODE;
+
+ if (rs485->flags & SER_RS485_ENABLED) {
+ /* Clear unsupported flags. */
+ rs485->flags &= SER_RS485_ENABLED | SER_RS485_RX_DURING_TX |
+ SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND;
+ tcr |= DW_UART_TCR_RS485_EN;
+
+ if (rs485->flags & SER_RS485_RX_DURING_TX) {
+ tcr |= DW_UART_TCR_XFER_MODE_DE_DURING_RE;
+ } else {
+ /* HW does not support same DE level for tx and rx */
+ if (!(rs485->flags & SER_RS485_RTS_ON_SEND) ==
+ !(rs485->flags & SER_RS485_RTS_AFTER_SEND))
+ return -EINVAL;
+
+ tcr |= DW_UART_TCR_XFER_MODE_DE_OR_RE;
+ }
+ dw8250_writel_ext(p, DW_UART_DE_EN, 1);
+ dw8250_writel_ext(p, DW_UART_RE_EN, 1);
+ } else {
+ rs485->flags = 0;
+
+ tcr &= ~DW_UART_TCR_RS485_EN;
+ }
+
+ /* Reset to default polarity */
+ tcr |= DW_UART_TCR_DE_POL;
+ tcr &= ~DW_UART_TCR_RE_POL;
+
+ if (!(rs485->flags & SER_RS485_RTS_ON_SEND))
+ tcr &= ~DW_UART_TCR_DE_POL;
+ if (device_property_read_bool(p->dev, "rs485-rx-active-high"))
+ tcr |= DW_UART_TCR_RE_POL;
+
+ dw8250_writel_ext(p, DW_UART_TCR, tcr);
+
+ rs485->delay_rts_before_send = 0;
+ rs485->delay_rts_after_send = 0;
+
+ p->rs485 = *rs485;
+
+ return 0;
+}
+
+/*
+ * Tests if RE_EN register can have non-zero value to see if RS-485 HW support
+ * is present.
+ */
+static bool dw8250_detect_rs485_hw(struct uart_port *p)
+{
+ u32 reg;
+
+ dw8250_writel_ext(p, DW_UART_RE_EN, 1);
+ reg = dw8250_readl_ext(p, DW_UART_RE_EN);
+ dw8250_writel_ext(p, DW_UART_RE_EN, 0);
+ return reg;
+}
+
void dw8250_setup_port(struct uart_port *p)
{
+ struct dw8250_port_data *d = p->private_data;
struct uart_8250_port *up = up_to_u8250p(p);
u32 reg;
+ d->hw_rs485_support = dw8250_detect_rs485_hw(p);
+ if (d->hw_rs485_support)
+ p->rs485_config = dw8250_rs485_config;
+
/*
* If the Component Version Register returns zero, we know that
* ADDITIONAL_FEATURES are not enabled. No need to go any further.
@@ -108,8 +191,6 @@ void dw8250_setup_port(struct uart_port *p)
dw8250_writel_ext(p, DW_UART_DLF, 0);
if (reg) {
- struct dw8250_port_data *d = p->private_data;
-
d->dlf_size = fls(reg);
p->get_divisor = dw8250_get_divisor;
p->set_divisor = dw8250_set_divisor;
@@ -14,6 +14,9 @@ struct dw8250_port_data {
/* Hardware configuration */
u8 dlf_size;
+
+ /* RS485 variables */
+ bool hw_rs485_support;
};
void dw8250_do_set_termios(struct uart_port *p, struct ktermios *termios, struct ktermios *old);