@@ -2498,6 +2498,40 @@ static void dwc3_gadget_disable_irq(struct dwc3 *dwc);
static void __dwc3_gadget_stop(struct dwc3 *dwc);
static int __dwc3_gadget_start(struct dwc3 *dwc);
+static int dwc3_gadget_soft_disconnect(struct dwc3 *dwc)
+{
+ u32 count;
+
+ dwc->connected = false;
+
+ /*
+ * In the Synopsys DesignWare Cores USB3 Databook Rev. 3.30a
+ * Section 4.1.8 Table 4-7, it states that for a device-initiated
+ * disconnect, the SW needs to ensure that it sends "a DEPENDXFER
+ * command for any active transfers" before clearing the RunStop
+ * bit.
+ */
+ dwc3_stop_active_transfers(dwc);
+ __dwc3_gadget_stop(dwc);
+
+ /*
+ * In the Synopsys DesignWare Cores USB3 Databook Rev. 3.30a
+ * Section 1.3.4, it mentions that for the DEVCTRLHLT bit, the
+ * "software needs to acknowledge the events that are generated
+ * (by writing to GEVNTCOUNTn) while it is waiting for this bit
+ * to be set to '1'."
+ */
+ count = dwc3_readl(dwc->regs, DWC3_GEVNTCOUNT(0));
+ count &= DWC3_GEVNTCOUNT_MASK;
+ if (count > 0) {
+ dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), count);
+ dwc->ev_buf->lpos = (dwc->ev_buf->lpos + count) %
+ dwc->ev_buf->length;
+ }
+
+ return dwc3_gadget_run_stop(dwc, false, false);
+}
+
static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
{
struct dwc3 *dwc = gadget_to_dwc(g);
@@ -2554,33 +2588,7 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
spin_lock_irqsave(&dwc->lock, flags);
if (!is_on) {
- u32 count;
-
- dwc->connected = false;
- /*
- * In the Synopsis DesignWare Cores USB3 Databook Rev. 3.30a
- * Section 4.1.8 Table 4-7, it states that for a device-initiated
- * disconnect, the SW needs to ensure that it sends "a DEPENDXFER
- * command for any active transfers" before clearing the RunStop
- * bit.
- */
- dwc3_stop_active_transfers(dwc);
- __dwc3_gadget_stop(dwc);
-
- /*
- * In the Synopsis DesignWare Cores USB3 Databook Rev. 3.30a
- * Section 1.3.4, it mentions that for the DEVCTRLHLT bit, the
- * "software needs to acknowledge the events that are generated
- * (by writing to GEVNTCOUNTn) while it is waiting for this bit
- * to be set to '1'."
- */
- count = dwc3_readl(dwc->regs, DWC3_GEVNTCOUNT(0));
- count &= DWC3_GEVNTCOUNT_MASK;
- if (count > 0) {
- dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), count);
- dwc->ev_buf->lpos = (dwc->ev_buf->lpos + count) %
- dwc->ev_buf->length;
- }
+ ret = dwc3_gadget_soft_disconnect(dwc);
} else {
/*
* In the Synopsys DWC_usb31 1.90a programming guide section
@@ -2594,9 +2602,8 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
dwc3_event_buffers_setup(dwc);
__dwc3_gadget_start(dwc);
+ ret = dwc3_gadget_run_stop(dwc, true, false);
}
-
- ret = dwc3_gadget_run_stop(dwc, is_on, false);
spin_unlock_irqrestore(&dwc->lock, flags);
enable_irq(dwc->irq_gadget);
Move soft-disconnect sequence out of dwc3_gadget_pullup(). No functional change here. Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> --- drivers/usb/dwc3/gadget.c | 65 ++++++++++++++++++++++----------------- 1 file changed, 36 insertions(+), 29 deletions(-)