@@ -403,6 +403,13 @@ static int btbcm_read_info(struct hci_dev *hdev)
bt_dev_info(hdev, "BCM: chip id %u", skb->data[1]);
kfree_skb(skb);
+ return 0;
+}
+
+static int btbcm_print_controller_features(struct hci_dev *hdev)
+{
+ struct sk_buff *skb;
+
/* Read Controller Features */
skb = btbcm_read_controller_features(hdev);
if (IS_ERR(skb))
@@ -513,7 +520,7 @@ static const char *btbcm_get_board_name(struct device *dev)
#endif
}
-int btbcm_initialize(struct hci_dev *hdev, bool *fw_load_done)
+int btbcm_initialize(struct hci_dev *hdev, bool *fw_load_done, bool use_autobaud_mode)
{
u16 subver, rev, pid, vid;
struct sk_buff *skb;
@@ -550,9 +557,16 @@ int btbcm_initialize(struct hci_dev *hdev, bool *fw_load_done)
if (err)
return err;
}
- err = btbcm_print_local_name(hdev);
- if (err)
- return err;
+
+ if (!use_autobaud_mode) {
+ err = btbcm_print_controller_features(hdev);
+ if (err)
+ return err;
+
+ err = btbcm_print_local_name(hdev);
+ if (err)
+ return err;
+ }
bcm_subver_table = (hdev->bus == HCI_USB) ? bcm_usb_subver_table :
bcm_uart_subver_table;
@@ -635,13 +649,13 @@ int btbcm_initialize(struct hci_dev *hdev, bool *fw_load_done)
}
EXPORT_SYMBOL_GPL(btbcm_initialize);
-int btbcm_finalize(struct hci_dev *hdev, bool *fw_load_done)
+int btbcm_finalize(struct hci_dev *hdev, bool *fw_load_done, bool use_autobaud_mode)
{
int err;
/* Re-initialize if necessary */
if (*fw_load_done) {
- err = btbcm_initialize(hdev, fw_load_done);
+ err = btbcm_initialize(hdev, fw_load_done, use_autobaud_mode);
if (err)
return err;
}
@@ -657,15 +671,16 @@ EXPORT_SYMBOL_GPL(btbcm_finalize);
int btbcm_setup_patchram(struct hci_dev *hdev)
{
bool fw_load_done = false;
+ bool use_autobaud_mode = false;
int err;
/* Initialize */
- err = btbcm_initialize(hdev, &fw_load_done);
+ err = btbcm_initialize(hdev, &fw_load_done, use_autobaud_mode);
if (err)
return err;
/* Re-initialize after loading Patch */
- return btbcm_finalize(hdev, &fw_load_done);
+ return btbcm_finalize(hdev, &fw_load_done, use_autobaud_mode);
}
EXPORT_SYMBOL_GPL(btbcm_setup_patchram);
@@ -62,8 +62,8 @@ int btbcm_write_pcm_int_params(struct hci_dev *hdev,
int btbcm_setup_patchram(struct hci_dev *hdev);
int btbcm_setup_apple(struct hci_dev *hdev);
-int btbcm_initialize(struct hci_dev *hdev, bool *fw_load_done);
-int btbcm_finalize(struct hci_dev *hdev, bool *fw_load_done);
+int btbcm_initialize(struct hci_dev *hdev, bool *fw_load_done, bool use_autobaud_mode);
+int btbcm_finalize(struct hci_dev *hdev, bool *fw_load_done, bool use_autobaud_mode);
#else
@@ -104,12 +104,12 @@ static inline int btbcm_setup_apple(struct hci_dev *hdev)
return 0;
}
-static inline int btbcm_initialize(struct hci_dev *hdev, bool *fw_load_done)
+static inline int btbcm_initialize(struct hci_dev *hdev, bool *fw_load_done, bool use_autobaud_mode)
{
return 0;
}
-static inline int btbcm_finalize(struct hci_dev *hdev, bool *fw_load_done)
+static inline int btbcm_finalize(struct hci_dev *hdev, bool *fw_load_done, bool use_autobaud_mode)
{
return 0;
}
@@ -99,6 +99,7 @@ struct bcm_device_data {
* @no_early_set_baudrate: don't set_baudrate before setup()
* @drive_rts_on_open: drive RTS signal on ->open() when platform requires it
* @pcm_int_params: keep the initial PCM configuration
+ * @use_autobaud_mode: start Bluetooth device in autobaud mode
*/
struct bcm_device {
/* Must be the first member, hci_serdev.c expects this. */
@@ -136,6 +137,7 @@ struct bcm_device {
#endif
bool no_early_set_baudrate;
bool drive_rts_on_open;
+ bool use_autobaud_mode;
u8 pcm_int_params[5];
};
@@ -472,7 +474,9 @@ static int bcm_open(struct hci_uart *hu)
out:
if (bcm->dev) {
- if (bcm->dev->drive_rts_on_open)
+ if (bcm->dev->use_autobaud_mode)
+ hci_uart_set_flow_control(hu, false); /* Assert BT_UART_CTS_N */
+ else if (bcm->dev->drive_rts_on_open)
hci_uart_set_flow_control(hu, true);
hu->init_speed = bcm->dev->init_speed;
@@ -564,6 +568,7 @@ static int bcm_setup(struct hci_uart *hu)
{
struct bcm_data *bcm = hu->priv;
bool fw_load_done = false;
+ bool use_autobaud_mode = (bcm->dev ? bcm->dev->use_autobaud_mode : 0);
unsigned int speed;
int err;
@@ -572,7 +577,7 @@ static int bcm_setup(struct hci_uart *hu)
hu->hdev->set_diag = bcm_set_diag;
hu->hdev->set_bdaddr = btbcm_set_bdaddr;
- err = btbcm_initialize(hu->hdev, &fw_load_done);
+ err = btbcm_initialize(hu->hdev, &fw_load_done, use_autobaud_mode);
if (err)
return err;
@@ -616,7 +621,7 @@ static int bcm_setup(struct hci_uart *hu)
btbcm_write_pcm_int_params(hu->hdev, ¶ms);
}
- err = btbcm_finalize(hu->hdev, &fw_load_done);
+ err = btbcm_finalize(hu->hdev, &fw_load_done, use_autobaud_mode);
if (err)
return err;
@@ -1197,6 +1202,10 @@ static int bcm_acpi_probe(struct bcm_device *dev)
static int bcm_of_probe(struct bcm_device *bdev)
{
+ bdev->use_autobaud_mode = device_property_read_bool(bdev->dev, "brcm,uses-autobaud-mode");
+ if (bdev->use_autobaud_mode)
+ bdev->no_early_set_baudrate = true;
+
device_property_read_u32(bdev->dev, "max-speed", &bdev->oper_speed);
device_property_read_u8_array(bdev->dev, "brcm,bt-pcm-int-params",
bdev->pcm_int_params, 5);
Some devices (e.g. CYW5557x) require autobaud mode to enable FW loading. Autobaud mode can also be required on some boards where the controller device is using a non-standard baud rate when first powered on. Only a limited subset of HCI commands are supported in autobaud mode. This patch looks for a DT property, "brcm,uses-autobaud-mode", to enable autobaud mode selection. If the property is present, the device is started in autobaud mode by keeping RTS asserted while powering on the device. The patch also prevents the use of unsupported commands for devices started in autobaud mode. Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com> --- V1 -> V2: No changes, submitted as part of updated patch series drivers/bluetooth/btbcm.c | 31 +++++++++++++++++++++++-------- drivers/bluetooth/btbcm.h | 8 ++++---- drivers/bluetooth/hci_bcm.c | 15 ++++++++++++--- 3 files changed, 39 insertions(+), 15 deletions(-)