@@ -4,60 +4,63 @@
$id: http://devicetree.org/schemas/net/dsa/mediatek,mt7530.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
-title: Mediatek MT7530 Ethernet switch
+title: Mediatek MT7530 and MT7531 Ethernet Switches
maintainers:
- - Sean Wang <sean.wang@mediatek.com>
+ - Arınç ÜNAL <arinc.unal@arinc9.com>
- Landen Chao <Landen.Chao@mediatek.com>
- DENG Qingfang <dqfext@gmail.com>
+ - Sean Wang <sean.wang@mediatek.com>
description: |
- Port 5 of mt7530 and mt7621 switch is muxed between:
- 1. GMAC5: GMAC5 can interface with another external MAC or PHY.
- 2. PHY of port 0 or port 4: PHY interfaces with an external MAC like 2nd GMAC
- of the SOC. Used in many setups where port 0/4 becomes the WAN port.
- Note: On a MT7621 SOC with integrated switch: 2nd GMAC can only connected to
- GMAC5 when the gpios for RGMII2 (GPIO 22-33) are not used and not
- connected to external component!
-
- Port 5 modes/configurations:
- 1. Port 5 is disabled and isolated: An external phy can interface to the 2nd
- GMAC of the SOC.
- In the case of a build-in MT7530 switch, port 5 shares the RGMII bus with 2nd
- GMAC and an optional external phy. Mind the GPIO/pinctl settings of the SOC!
- 2. Port 5 is muxed to PHY of port 0/4: Port 0/4 interfaces with 2nd GMAC.
- It is a simple MAC to PHY interface, port 5 needs to be setup for xMII mode
- and RGMII delay.
- 3. Port 5 is muxed to GMAC5 and can interface to an external phy.
- Port 5 becomes an extra switch port.
- Only works on platform where external phy TX<->RX lines are swapped.
- Like in the Ubiquiti ER-X-SFP.
- 4. Port 5 is muxed to GMAC5 and interfaces with the 2nd GAMC as 2nd CPU port.
- Currently a 2nd CPU port is not supported by DSA code.
-
- Depending on how the external PHY is wired:
- 1. normal: The PHY can only connect to 2nd GMAC but not to the switch
- 2. swapped: RGMII TX, RX are swapped; external phy interface with the switch as
- a ethernet port. But can't interface to the 2nd GMAC.
-
- Based on the DT the port 5 mode is configured.
-
- Driver tries to lookup the phy-handle of the 2nd GMAC of the master device.
- When phy-handle matches PHY of port 0 or 4 then port 5 set-up as mode 2.
- phy-mode must be set, see also example 2 below!
- * mt7621: phy-mode = "rgmii-txid";
- * mt7623: phy-mode = "rgmii";
-
- CPU-Ports need a phy-mode property:
- Allowed values on mt7530 and mt7621:
- - "rgmii"
- - "trgmii"
- On mt7531:
- - "1000base-x"
- - "2500base-x"
- - "rgmii"
- - "sgmii"
+ There are two versions of MT7530. MT7621AT, MT7621DAT, MT7621ST and MT7623AI
+ SoCs include MT7530 which is a part of the multi-chip module.
+ The other version of MT7530 comes as a standalone chip.
+ There is only one version of MT7531 which comes as a standalone chip.
+
+ Port 5 on MT7530 has got various ways of configuration.
+
+ For standalone MT7530:
+
+ - Port 5 can be used as a DSA master.
+ This is currently not supported on the driver.
+
+ - PHY 0 or 4 of the switch can be muxed to connect to the gmac of the SoC
+ which port 5 is wired to. Usually used for connecting the wan port
+ directly to the CPU to achieve 2 Gbps routing in total.
+
+ The driver requires the gmac of the SoC to have "mediatek,eth-mac" as the
+ compatible string and the reg must be 1. So, for now, only gmac1 of an
+ MediaTek SoC can benefit this. Banana Pi BPI-R2 for example.
+ Check out example 5 for a similar configuration.
+
+ - Port 5 can be wired to an external phy. Port 5 becomes a DSA slave.
+ Check out example 7 for a similar configuration.
+
+ For multi-chip module MT7530:
+
+ - Port 5 can be used as a DSA master.
+ This is currently not supported on the driver.
+
+ - PHY 0 or 4 of the switch can be muxed to connect to gmac1 of the SoC.
+ Usually used for connecting the wan port directly to the CPU to achieve 2
+ Gbps routing in total.
+
+ For the MT7621 SoCs, rgmii2 group must be claimed with rgmii2 function.
+ Check out example 5.
+
+ - In case of an external phy wired to gmac1 of the SoC, port 5 must not be
+ enabled.
+
+ For the MT7621 SoCs, rgmii2 group must be claimed with rgmii2 function.
+ Check out example 6.
+ - Port 5 can be muxed to an external phy. Port 5 becomes a DSA slave.
+ The external phy must be wired TX to TX to gmac1 of the SoC for this to
+ work. Ubiquiti EdgeRouter X SFP for example.
+
+ For the MT7621 SoCs, rgmii2 group must be claimed with gpio function.
+ Check out example 7.
properties:
compatible:
@@ -66,6 +69,14 @@ properties:
- mediatek,mt7531
- mediatek,mt7621
+ description: |
+ mediatek,mt7530:
+ For standalone MT7530 and multi-chip module MT7530 in MT7623AI SoC.
+ mediatek,mt7531:
+ For standalone MT7531.
+ mediatek,mt7621:
+ For multi-chip module MT7530 in MT7621AT, MT7621DAT and MT7621ST SoCs.
+
reg:
maxItems: 1
@@ -79,7 +90,7 @@ properties:
gpio-controller:
type: boolean
description:
- if defined, MT7530's LED controller will run on GPIO mode.
+ If defined, MT7530's LED controller will run on GPIO mode.
"#interrupt-cells":
const: 1
@@ -98,11 +109,14 @@ properties:
mediatek,mcm:
type: boolean
description:
- if defined, indicates that either MT7530 is the part on multi-chip
- module belong to MT7623A has or the remotely standalone chip as the
- function MT7623N reference board provided for.
+ Used for MT7621AT, MT7621DAT, MT7621ST and MT7623AI SoCs which the MT7530
+ switch is a part of the multi-chip module.
reset-gpios:
+ description:
+ GPIO to reset the switch. Use this if mediatek,mcm is not used.
+ This is optional since some boards share the reset line with other
+ components which makes it impossible to probe the switch.
maxItems: 1
reset-names:
@@ -114,41 +128,12 @@ properties:
the ethsys.
maxItems: 1
-patternProperties:
- "^(ethernet-)?ports$":
- type: object
-
- patternProperties:
- "^(ethernet-)?port@[0-9]+$":
- type: object
- description: Ethernet switch ports
-
- unevaluatedProperties: false
-
- properties:
- reg:
- description:
- Port address described must be 5 or 6 for CPU port and from 0
- to 5 for user ports.
-
- allOf:
- - $ref: dsa-port.yaml#
- - if:
- properties:
- label:
- items:
- - const: cpu
- then:
- required:
- - reg
- - phy-mode
-
required:
- compatible
- reg
allOf:
- - $ref: "dsa.yaml#"
+ - $ref: dsa.yaml#
- if:
required:
- mediatek,mcm
@@ -166,151 +151,531 @@ allOf:
items:
- const: mediatek,mt7530
then:
+ patternProperties:
+ "^(ethernet-)?ports$":
+ type: object
+
+ patternProperties:
+ "^(ethernet-)?port@[0-9]+$":
+ type: object
+ description: Ethernet switch ports
+
+ unevaluatedProperties: false
+
+ properties:
+ reg:
+ description:
+ Port address described must be 6 for CPU port and from 0 to
+ 5 for user ports.
+
+ allOf:
+ - $ref: dsa-port.yaml#
+ - if:
+ properties:
+ label:
+ items:
+ - const: cpu
+ then:
+ properties:
+ phy-mode:
+ enum:
+ - rgmii
+ - trgmii
+
+ reg:
+ enum:
+ - 6
+
+ required:
+ - phy-mode
+
required:
- core-supply
- io-supply
+ - if:
+ properties:
+ compatible:
+ items:
+ - const: mediatek,mt7531
+ then:
+ patternProperties:
+ "^(ethernet-)?ports$":
+ type: object
+
+ patternProperties:
+ "^(ethernet-)?port@[0-9]+$":
+ type: object
+ description: Ethernet switch ports
+
+ unevaluatedProperties: false
+
+ properties:
+ reg:
+ description:
+ Port address described must be 5 or 6 for CPU port and from
+ 0 to 5 for user ports.
+
+ allOf:
+ - $ref: dsa-port.yaml#
+ - if:
+ properties:
+ label:
+ items:
+ - const: cpu
+ then:
+ allOf:
+ - if:
+ properties:
+ reg:
+ const: 5
+ then:
+ properties:
+ phy-mode:
+ enum:
+ - 1000base-x
+ - 2500base-x
+ - rgmii
+ - sgmii
+
+ - if:
+ properties:
+ reg:
+ const: 6
+ then:
+ properties:
+ phy-mode:
+ enum:
+ - 1000base-x
+ - 2500base-x
+ - sgmii
+
+ properties:
+ reg:
+ enum:
+ - 5
+ - 6
+
+ required:
+ - phy-mode
+
+ - if:
+ properties:
+ compatible:
+ items:
+ - const: mediatek,mt7621
+ then:
+ patternProperties:
+ "^(ethernet-)?ports$":
+ type: object
+
+ patternProperties:
+ "^(ethernet-)?port@[0-9]+$":
+ type: object
+ description: Ethernet switch ports
+
+ unevaluatedProperties: false
+
+ properties:
+ reg:
+ description:
+ Port address described must be 6 for CPU port and from 0 to
+ 5 for user ports.
+
+ allOf:
+ - $ref: dsa-port.yaml#
+ - if:
+ properties:
+ label:
+ items:
+ - const: cpu
+ then:
+ properties:
+ phy-mode:
+ enum:
+ - rgmii
+ - trgmii
+
+ reg:
+ enum:
+ - 6
+
+ required:
+ - phy-mode
+
+ required:
+ - mediatek,mcm
+
unevaluatedProperties: false
examples:
+ # Example 1: Standalone MT7530
- |
#include <dt-bindings/gpio/gpio.h>
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- switch@0 {
- compatible = "mediatek,mt7530";
- reg = <0>;
-
- core-supply = <&mt6323_vpa_reg>;
- io-supply = <&mt6323_vemc3v3_reg>;
- reset-gpios = <&pio 33 GPIO_ACTIVE_HIGH>;
-
- ethernet-ports {
+
+ platform {
+ ethernet {
+ mdio {
#address-cells = <1>;
#size-cells = <0>;
- port@0 {
+
+ switch@0 {
+ compatible = "mediatek,mt7530";
reg = <0>;
- label = "lan0";
- };
- port@1 {
- reg = <1>;
- label = "lan1";
- };
+ reset-gpios = <&pio 33 0>;
- port@2 {
- reg = <2>;
- label = "lan2";
- };
+ core-supply = <&mt6323_vpa_reg>;
+ io-supply = <&mt6323_vemc3v3_reg>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
- port@3 {
- reg = <3>;
- label = "lan3";
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "rgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
};
+ };
+ };
+ };
- port@4 {
- reg = <4>;
- label = "wan";
+ # Example 2: MT7530 in MT7623AI SoC
+ - |
+ #include <dt-bindings/reset/mt2701-resets.h>
+
+ platform {
+ ethernet {
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch@0 {
+ compatible = "mediatek,mt7530";
+ reg = <0>;
+
+ mediatek,mcm;
+ resets = <ðsys MT2701_ETHSYS_MCM_RST>;
+ reset-names = "mcm";
+
+ core-supply = <&mt6323_vpa_reg>;
+ io-supply = <&mt6323_vemc3v3_reg>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "trgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
};
+ };
+ };
+ };
+
+ # Example 3: Standalone MT7531
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ platform {
+ ethernet {
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac0>;
- phy-mode = "trgmii";
- fixed-link {
- speed = <1000>;
- full-duplex;
+ switch@0 {
+ compatible = "mediatek,mt7531";
+ reg = <0>;
+
+ reset-gpios = <&pio 54 0>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <53 IRQ_TYPE_LEVEL_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
};
};
};
};
};
+ # Example 4: MT7530 in MT7621AT, MT7621DAT and MT7621ST SoCs
- |
- //Example 2: MT7621: Port 4 is WAN port: 2nd GMAC -> Port 5 -> PHY port 4.
-
- ethernet {
- #address-cells = <1>;
- #size-cells = <0>;
- gmac0: mac@0 {
- compatible = "mediatek,eth-mac";
- reg = <0>;
- phy-mode = "rgmii";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- pause;
+ #include <dt-bindings/interrupt-controller/mips-gic.h>
+ #include <dt-bindings/reset/mt7621-reset.h>
+
+ platform {
+ ethernet {
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch@0 {
+ compatible = "mediatek,mt7621";
+ reg = <0>;
+
+ mediatek,mcm;
+ resets = <&sysc MT7621_RST_MCM>;
+ reset-names = "mcm";
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "trgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+ };
};
};
+ };
- gmac1: mac@1 {
- compatible = "mediatek,eth-mac";
- reg = <1>;
- phy-mode = "rgmii-txid";
- phy-handle = <&phy4>;
+ # Example 5: MT7621: mux MT7530's phy4 to SoC's gmac1
+ - |
+ #include <dt-bindings/interrupt-controller/mips-gic.h>
+ #include <dt-bindings/reset/mt7621-reset.h>
+
+ platform {
+ pinctrl {
+ example5_rgmii2_pins: rgmii2-pins {
+ pinmux {
+ groups = "rgmii2";
+ function = "rgmii2";
+ };
+ };
};
- mdio: mdio-bus {
+ ethernet {
#address-cells = <1>;
#size-cells = <0>;
- /* Internal phy */
- phy4: ethernet-phy@4 {
- reg = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&example5_rgmii2_pins>;
+
+ mac@1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+
+ phy-handle = <&example5_ethphy4>;
};
- mt7530: switch@1f {
- compatible = "mediatek,mt7621";
- reg = <0x1f>;
- mediatek,mcm;
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
- resets = <&rstctrl 2>;
- reset-names = "mcm";
+ /* MT7530's phy4 */
+ example5_ethphy4: ethernet-phy@4 {
+ reg = <4>;
+ };
- ethernet-ports {
- #address-cells = <1>;
- #size-cells = <0>;
+ switch@0 {
+ compatible = "mediatek,mt7621";
+ reg = <0>;
- port@0 {
- reg = <0>;
- label = "lan0";
- };
+ mediatek,mcm;
+ resets = <&sysc MT7621_RST_MCM>;
+ reset-names = "mcm";
- port@1 {
- reg = <1>;
- label = "lan1";
- };
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>;
- port@2 {
- reg = <2>;
- label = "lan2";
- };
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
- port@3 {
- reg = <3>;
- label = "lan3";
- };
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
- /* Commented out. Port 4 is handled by 2nd GMAC.
- port@4 {
- reg = <4>;
- label = "lan4";
- };
- */
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac0>;
- phy-mode = "rgmii";
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
- fixed-link {
- speed = <1000>;
- full-duplex;
- pause;
+ /* Commented out, phy4 is muxed to gmac1.
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ };
+ */
+
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "trgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
};
};
};
@@ -318,87 +683,197 @@ examples:
};
};
+ # Example 6: MT7621: mux external phy to SoC's gmac1
- |
- //Example 3: MT7621: Port 5 is connected to external PHY: Port 5 -> external PHY.
-
- ethernet {
- #address-cells = <1>;
- #size-cells = <0>;
- gmac_0: mac@0 {
- compatible = "mediatek,eth-mac";
- reg = <0>;
- phy-mode = "rgmii";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- pause;
+ #include <dt-bindings/interrupt-controller/mips-gic.h>
+ #include <dt-bindings/reset/mt7621-reset.h>
+
+ platform {
+ pinctrl {
+ example6_rgmii2_pins: rgmii2-pins {
+ pinmux {
+ groups = "rgmii2";
+ function = "rgmii2";
+ };
};
};
- mdio0: mdio-bus {
+ ethernet {
#address-cells = <1>;
#size-cells = <0>;
- /* External phy */
- ephy5: ethernet-phy@7 {
- reg = <7>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&example6_rgmii2_pins>;
+
+ mac@1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+
+ phy-handle = <&example6_ethphy7>;
+ phy-mode = "rgmii";
};
- switch@1f {
- compatible = "mediatek,mt7621";
- reg = <0x1f>;
- mediatek,mcm;
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
- resets = <&rstctrl 2>;
- reset-names = "mcm";
+ /* External PHY */
+ example6_ethphy7: ethernet-phy@7 {
+ reg = <7>;
+ phy-mode = "rgmii";
+ };
- ethernet-ports {
- #address-cells = <1>;
- #size-cells = <0>;
+ switch@0 {
+ compatible = "mediatek,mt7621";
+ reg = <0>;
- port@0 {
- reg = <0>;
- label = "lan0";
- };
+ mediatek,mcm;
+ resets = <&sysc MT7621_RST_MCM>;
+ reset-names = "mcm";
- port@1 {
- reg = <1>;
- label = "lan1";
- };
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>;
- port@2 {
- reg = <2>;
- label = "lan2";
- };
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
- port@3 {
- reg = <3>;
- label = "lan3";
- };
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
- port@4 {
- reg = <4>;
- label = "lan4";
- };
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
- port@5 {
- reg = <5>;
- label = "lan5";
- phy-mode = "rgmii";
- phy-handle = <&ephy5>;
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "trgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
};
+ };
+ };
+ };
+ };
+
+ # Example 7: MT7621: mux external phy to MT7530's port 5
+ - |
+ #include <dt-bindings/interrupt-controller/mips-gic.h>
+ #include <dt-bindings/reset/mt7621-reset.h>
+
+ platform {
+ pinctrl {
+ example7_rgmii2_pins: rgmii2-pins {
+ pinmux {
+ groups = "rgmii2";
+ function = "gpio";
+ };
+ };
+ };
+
+ ethernet {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&example7_rgmii2_pins>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* External PHY */
+ example7_ethphy7: ethernet-phy@7 {
+ reg = <7>;
+ };
+
+ switch@0 {
+ compatible = "mediatek,mt7621";
+ reg = <0>;
+
+ mediatek,mcm;
+ resets = <&sysc MT7621_RST_MCM>;
+ reset-names = "mcm";
- cpu_port0: port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac_0>;
- phy-mode = "rgmii";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "extphy";
+ phy-mode = "rgmii-txid";
+ phy-handle = <&example7_ethphy7>;
+ };
- fixed-link {
- speed = <1000>;
- full-duplex;
- pause;
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "trgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
};
};
};
Completely rework the binding for MediaTek MT7530 and MT7531 switches. - Update title to include MT7531 switch. - Add me as a maintainer. List maintainers in alphabetical order by first name. - Update binding description. Describe the switches, which SoCs they are on, or if they are standalone. - Add description to compatible strings. - Fix MCM description. mediatek,mcm is not used on MT7623NI. - Remove phy-mode = “rgmii-txid” from description. Same code path is followed for delayed rgmii and rgmii phy-mode on mtk_eth_soc.c. - Define acceptable phy-mode values for certain compatible strings and dsa port regs. - Remove requiring reg since the referred dsa-port.yaml already does that. - Remove quotes from $ref: "dsa.yaml#". - Require mediatek,mcm for MT7621 as the compatible string is only used for MT7530 which is a part of the multi-chip module. - Add description for reset-gpios. - Only allow port 6 to be the cpu port for MT7530 as port 5 is not supported yet. Examples: - Add examples which include all different configurations. - Make example comments YAML comment instead of DT binding comment. - Define examples from platform to make the bindings clearer. - Add interrupt controller to the examples. Include header file for interrupt. - Change reset line for MT7621 examples. - Pretty formatting for the examples. - Change switch reg to 0. - Change port labels to fit the example, change some lan labels to wan. Make port 4, wan. - Change ethernet-ports to ports. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> --- I’m new to json schema so I experimented a lot with this binding. Open to suggestions! I've checked the bindings with "make dt_binding_check DT_SCHEMA_FILES=mediatek,mt7530.yaml". If anyone knows the GIC bit for interrupt for multi-chip module MT7530 in MT7623AI SoC, let me know. I’ll add it to the examples. PHY0/4 muxing on MT7623AI may be possible. Has anyone got a Unielec U7623 or another MT7623AI board to test? We require the interrupt-parent right? interrupts property shouldn't make sense without the parent defined, such as GIC or GPIO. I have it missing on a devicetree, I want to add it. trgmii speed is 1200 Mbps. Are we supposed to use 2500 speed for fixed-link trgmii? To Frank: Let me know if MII bindings for port 5 and 6 on MT7531 are okay. Does your recent patch for MT7531 make it possible to set any port for CPU, including user ports? For now, I put a rule to restrict CPU ports to 5 and 6, as described on the description of dsa port reg property. I suppose your patch does not bring support for using MT7530's port 5 as CPU port. We could try this on a BPI-R2. Device schematics show that MT7530's GMII pins are wired to GMAC1 of MT7623NI to work as RGMII. Arınç --- .../bindings/net/dsa/mediatek,mt7530.yaml | 959 +++++++++++++----- 1 file changed, 717 insertions(+), 242 deletions(-)