Allow S/G_PARM for stateful decoder

Some stateful decoder supports S/G_PARM similar to a
stateful encoder. S_PARM(OUTPUT) reserves hardware decoder
resources, and G_PARM(CAPTURE) returns the embedded
frame interval. Allow the same with this change.

Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
---
 utils/v4l2-compliance/v4l2-test-formats.cpp | 4 ----
 1 file changed, 4 deletions(-)

Hi Dikshita,

First I'll comment on this patch, then at the end I have more high-level
comments.

On 29/08/2022 09:54, Dikshita Agarwal wrote:
> Some stateful decoder supports S/G_PARM similar to a

decoder -> decoders

BTW, which decoder drivers support this in mainline? Or is this
for out-of-tree drivers?

> stateful encoder. S_PARM(OUTPUT) reserves hardware decoder
> resources, and G_PARM(CAPTURE) returns the embedded
> frame interval. Allow the same with this change.
> 
> Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
> ---
>  utils/v4l2-compliance/v4l2-test-formats.cpp | 4 ----
>  1 file changed, 4 deletions(-)
> 
> diff --git a/utils/v4l2-compliance/v4l2-test-formats.cpp b/utils/v4l2-compliance/v4l2-test-formats.cpp
> index 269a383..e996558 100644
> --- a/utils/v4l2-compliance/v4l2-test-formats.cpp
> +++ b/utils/v4l2-compliance/v4l2-test-formats.cpp
> @@ -64,8 +64,6 @@ static int testEnumFrameIntervals(struct node *node, __u32 pixfmt,
>  		ret = doioctl(node, VIDIOC_ENUM_FRAMEINTERVALS, &frmival);
>  		if (ret == ENOTTY)
>  			return ret;
> -		// M2M devices don't support this, except for stateful encoders
> -		fail_on_test(node->is_m2m && !(node->codec_mask & STATEFUL_ENCODER));

M2M devices still don't support this, except for stateful codecs. So this test
should still be there, just changed to:

!(node->codec_mask & (STATEFUL_ENCODER | STATEFUL_DECODER))

>  		if (f == 0 && ret == EINVAL) {
>  			if (type == V4L2_FRMSIZE_TYPE_DISCRETE)
>  				warn("found framesize %dx%d, but no frame intervals\n", w, h);
> @@ -1367,8 +1365,6 @@ static int testParmType(struct node *node, unsigned type)
>  	}
>  	if (ret == ENOTTY)
>  		return ret;
> -	// M2M devices don't support this, except for stateful encoders
> -	fail_on_test(node->is_m2m && !is_stateful_enc);

Similar.

>  	if (ret == EINVAL)
>  		return ENOTTY;
>  	if (ret)

But modifying the utility is something you only do if the spec has first been updated.
So the stateful decoder chapter needs to be modified so it explains how G/S_PARM
shall be used. And ideally have at least one driver that supports it.

Regards,

	Hans

Thanks, Hans, for your comments.

I will take care of all comments regarding this change in next patch.

Will also send a patch to update the documentation.
Venus driver already has support for S_PARM for decoder, will add support for G_PARM as well and send a patch.

Thanks,
Dikshita
-----Original Message-----
From: Hans Verkuil <hverkuil-cisco@xs4all.nl> 
Sent: Friday, September 9, 2022 5:47 PM
To: Dikshita Agarwal (QUIC) <quic_dikshita@quicinc.com>; linux-media@vger.kernel.org; linux-kernel@vger.kernel.org
Cc: stanimir.varbanov@linaro.org; Vikash Garodia (QUIC) <quic_vgarodia@quicinc.com>; Maheshwar Ajja (QUIC) <quic_majja@quicinc.com>; quic_jdas <quic_jdas@quicinc.com>
Subject: Re: [PATCH] Allow S/G_PARM for stateful decoder

Hi Dikshita,

First I'll comment on this patch, then at the end I have more high-level comments.

On 29/08/2022 09:54, Dikshita Agarwal wrote:
> Some stateful decoder supports S/G_PARM similar to a

decoder -> decoders

BTW, which decoder drivers support this in mainline? Or is this for out-of-tree drivers?

> stateful encoder. S_PARM(OUTPUT) reserves hardware decoder resources, 
> and G_PARM(CAPTURE) returns the embedded frame interval. Allow the 
> same with this change.
> 
> Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
> ---
>  utils/v4l2-compliance/v4l2-test-formats.cpp | 4 ----
>  1 file changed, 4 deletions(-)
> 
> diff --git a/utils/v4l2-compliance/v4l2-test-formats.cpp 
> b/utils/v4l2-compliance/v4l2-test-formats.cpp
> index 269a383..e996558 100644
> --- a/utils/v4l2-compliance/v4l2-test-formats.cpp
> +++ b/utils/v4l2-compliance/v4l2-test-formats.cpp
> @@ -64,8 +64,6 @@ static int testEnumFrameIntervals(struct node *node, __u32 pixfmt,
>  		ret = doioctl(node, VIDIOC_ENUM_FRAMEINTERVALS, &frmival);
>  		if (ret == ENOTTY)
>  			return ret;
> -		// M2M devices don't support this, except for stateful encoders
> -		fail_on_test(node->is_m2m && !(node->codec_mask & STATEFUL_ENCODER));

M2M devices still don't support this, except for stateful codecs. So this test should still be there, just changed to:

!(node->codec_mask & (STATEFUL_ENCODER | STATEFUL_DECODER))

>  		if (f == 0 && ret == EINVAL) {
>  			if (type == V4L2_FRMSIZE_TYPE_DISCRETE)
>  				warn("found framesize %dx%d, but no frame intervals\n", w, h); @@ 
> -1367,8 +1365,6 @@ static int testParmType(struct node *node, unsigned type)
>  	}
>  	if (ret == ENOTTY)
>  		return ret;
> -	// M2M devices don't support this, except for stateful encoders
> -	fail_on_test(node->is_m2m && !is_stateful_enc);

Similar.

>  	if (ret == EINVAL)
>  		return ENOTTY;
>  	if (ret)

But modifying the utility is something you only do if the spec has first been updated.
So the stateful decoder chapter needs to be modified so it explains how G/S_PARM shall be used. And ideally have at least one driver that supports it.

Regards,

	Hans