@@ -581,8 +581,8 @@ static ssize_t lp5523_selftest(struct device *dev,
struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev));
struct lp55xx_chip *chip = led->chip;
struct lp55xx_platform_data *pdata = chip->pdata;
- int i, ret, pos = 0;
- u8 status, adc, vdd;
+ int ret, pos = 0;
+ u8 status, adc, vdd, i;
mutex_lock(&chip->lock);
@@ -612,20 +612,21 @@ static ssize_t lp5523_selftest(struct device *dev,
vdd--; /* There may be some fluctuation in measurement */
- for (i = 0; i < LP5523_MAX_LEDS; i++) {
- /* Skip non-existing channels */
+ for (i = 0; i < pdata->num_channels; i++) {
+ /* Skip disabled channels */
if (pdata->led_config[i].led_current == 0)
continue;
/* Set default current */
- lp55xx_write(chip, LP5523_REG_LED_CURRENT_BASE + i,
+ lp55xx_write(chip, LP5523_REG_LED_CURRENT_BASE + led->chan_nr,
pdata->led_config[i].led_current);
- lp55xx_write(chip, LP5523_REG_LED_PWM_BASE + i, 0xff);
+ lp55xx_write(chip, LP5523_REG_LED_PWM_BASE + led->chan_nr,
+ 0xff);
/* let current stabilize 2 - 4ms before measurements start */
usleep_range(2000, 4000);
lp55xx_write(chip, LP5523_REG_LED_TEST_CTRL,
- LP5523_EN_LEDTEST | i);
+ LP5523_EN_LEDTEST | led->chan_nr);
/* ADC conversion time is 2.7 ms typically */
usleep_range(3000, 6000);
ret = lp55xx_read(chip, LP5523_REG_STATUS, &status);
@@ -633,20 +634,22 @@ static ssize_t lp5523_selftest(struct device *dev,
goto fail;
if (!(status & LP5523_LEDTEST_DONE))
- usleep_range(3000, 6000);/* Was not ready. Wait. */
+ usleep_range(3000, 6000); /* Was not ready. Wait. */
ret = lp55xx_read(chip, LP5523_REG_LED_TEST_ADC, &adc);
if (ret < 0)
goto fail;
if (adc >= vdd || adc < LP5523_ADC_SHORTCIRC_LIM)
- pos += sprintf(buf + pos, "LED %d FAIL\n", i);
+ pos += sprintf(buf + pos, "LED %d FAIL\n",
+ led->chan_nr);
- lp55xx_write(chip, LP5523_REG_LED_PWM_BASE + i, 0x00);
+ lp55xx_write(chip, LP5523_REG_LED_PWM_BASE + led->chan_nr,
+ 0x00);
/* Restore current */
- lp55xx_write(chip, LP5523_REG_LED_CURRENT_BASE + i,
- led->led_current);
+ lp55xx_write(chip, LP5523_REG_LED_CURRENT_BASE + led->chan_nr,
+ led->led_current);
led++;
}
if (pos == 0)
When not all LED channels of the led chip are configured, the sysfs selftest functionality gives erroneous results and tries to test all channels of the chip. There is a potential for LED overcurrent conditions since the test current will be set to values from out-of-bound regions. It is wrong to use pdata->led_config[i].led_current to skip absent channels as led_config[] only contains the configured LED channels. Instead of iterating over all the physical channels of the device, loop over the available LED configurations and use led->chan_nr to access the correct i2c registers. Keep the zero-check for the LED current as existing users might depend on this to disable a channel. Reported-by: Arne Staessen <a.staessen@televic.com> Signed-off-by: Maarten Zanders <maarten.zanders@mind.be> --- drivers/leds/leds-lp5523.c | 27 +++++++++++++++------------ 1 file changed, 15 insertions(+), 12 deletions(-)