| Message ID | 20221115170242.150246-4-srinivas.kandagatla@linaro.org |
|---|---|
| State | New |
| Headers | show |
| Series | arm64: dts: qcom: sc8280xp: add audio support | expand |
On 15/11/2022 18:02, Srinivas Kandagatla wrote: > Add support for SoundCard on X13s. This patch adds support for Headset > Playback, record and 2 DMICs on the Panel along with the regulators > required for powering up the LPASS codecs. > > Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > --- > .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 213 ++++++++++++++++++ > 1 file changed, 213 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts > index b2b744bb8a53..99c3021e8149 100644 > --- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts > +++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts > @@ -58,6 +58,16 @@ vreg_misc_3p3: regulator-misc-3p3 { > regulator-boot-on; > regulator-always-on; > }; > + > + vph_pwr: vph-pwr-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "VPH_VCC3R9"; > + regulator-min-microvolt = <3900000>; > + regulator-max-microvolt = <3900000>; > + > + regulator-always-on; > + regulator-boot-on; > + }; > }; > > &apps_rsc { > @@ -67,6 +77,13 @@ pmc8280-1-rpmh-regulators { > > vdd-l3-l5-supply = <&vreg_s11b>; > > + vreg_s10b: smps10 { > + regulator-name = "vreg_s10b"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > vreg_s11b: smps11 { > regulator-name = "vreg_s11b"; > regulator-min-microvolt = <1272000>; > @@ -74,6 +91,13 @@ vreg_s11b: smps11 { > regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > }; > > + vreg_s12b: smps12 { > + regulator-name = "vreg_s12b"; > + regulator-min-microvolt = <984000>; > + regulator-max-microvolt = <984000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > vreg_l3b: ldo3 { > regulator-name = "vreg_l3b"; > regulator-min-microvolt = <1200000>; > @@ -102,6 +126,7 @@ vreg_l6b: ldo6 { > pmc8280c-rpmh-regulators { > compatible = "qcom,pm8350c-rpmh-regulators"; > qcom,pmic-id = "c"; > + vdd-bob-supply = <&vph_pwr>; > > vreg_l1c: ldo1 { > regulator-name = "vreg_l1c"; > @@ -123,6 +148,13 @@ vreg_l13c: ldo13 { > regulator-max-microvolt = <3072000>; > regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > }; > + > + vreg_bob: bob { > + regulator-name = "vreg_bob"; > + regulator-min-microvolt = <3008000>; > + regulator-max-microvolt = <3960000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; > + }; > }; > > pmc8280-2-rpmh-regulators { > @@ -268,6 +300,80 @@ &remoteproc_nsp0 { > status = "okay"; > }; > > +&sound { > + compatible = "qcom,sc8280xp-sndcard"; > + model = "SC8280XP-LENOVO-X13S"; > + audio-routing = > + "SpkrLeft IN", "WSA_SPK1 OUT", > + "SpkrRight IN", "WSA_SPK2 OUT", > + "IN1_HPHL", "HPHL_OUT", > + "IN2_HPHR", "HPHR_OUT", > + "AMIC2", "MIC BIAS2", > + "VA DMIC0", "MIC BIAS1", > + "VA DMIC1", "MIC BIAS1", > + "VA DMIC2", "MIC BIAS3", > + "TX DMIC0", "MIC BIAS1", > + "TX DMIC1", "MIC BIAS2", > + "TX DMIC2", "MIC BIAS3", > + "TX SWR_ADC1", "ADC2_OUTPUT"; > + > + wcd-playback-dai-link { > + link-name = "WCD Playback"; > + cpu { > + sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>; > + }; > + codec { > + sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>; > + }; > + platform { > + sound-dai = <&q6apm>; > + }; > + }; > + > + wcd-capture-dai-link { > + link-name = "WCD Capture"; > + cpu { > + sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; > + }; > + > + codec { > + sound-dai = <&wcd938x 1>, <&swr2 0>, <&txmacro 0>; > + }; > + platform { > + sound-dai = <&q6apm>; > + }; > + }; > + > + wsa-dai-link { > + link-name = "WSA Playback"; > + cpu { > + sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>; > + }; > + > + codec { > + sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>; > + }; > + platform { > + sound-dai = <&q6apm>; > + }; > + }; > + > + va-dai-link { > + link-name = "VA Capture"; > + cpu { > + sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; > + }; > + > + platform { > + sound-dai = <&q6apm>; > + }; > + > + codec { > + sound-dai = <&vamacro 0>; > + }; > + }; > +}; > + > &usb_0 { > status = "okay"; > }; > @@ -346,9 +452,96 @@ edp_bl_pwm: edp-bl-pwm-state { > }; > }; > > +&soc { > + wcd938x: codec { > + compatible = "qcom,wcd9380-codec"; > + #sound-dai-cells = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&wcd_default>; > + reset-gpios = <&tlmm 106 0>; > + > + vdd-buck-supply = <&vreg_s10b>; > + vdd-rxtx-supply = <&vreg_s10b>; > + vdd-io-supply = <&vreg_s10b>; > + vdd-mic-bias-supply = <&vreg_bob>; > + qcom,micbias1-microvolt = <1800000>; > + qcom,micbias2-microvolt = <1800000>; > + qcom,micbias3-microvolt = <1800000>; > + qcom,micbias4-microvolt = <1800000>; > + qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>; > + qcom,mbhc-headset-vthreshold-microvolt = <1700000>; > + qcom,mbhc-headphone-vthreshold-microvolt = <50000>; > + qcom,rx-device = <&wcd_rx>; > + qcom,tx-device = <&wcd_tx>; > + }; > +}; > + > +&swr0 { > + left_spkr: wsa8830-left@0,1 { > + compatible = "sdw10217020200"; > + pinctrl-names = "default"; > + pinctrl-0 = <&spkr_1_sd_n_active>; > + powerdown-gpios = <&tlmm 178 GPIO_ACTIVE_HIGH>; > + reg = <0 1>; > + #thermal-sensor-cells = <0>; > + sound-name-prefix = "SpkrLeft"; > + #sound-dai-cells = <0>; > + vdd-supply = <&vreg_s10b>; > + }; > + > + right_spkr: wsa8830-right@0,2{ > + pinctrl-names = "default"; > + pinctrl-0 = <&spkr_2_sd_n_active>; > + powerdown-gpios = <&tlmm 179 GPIO_ACTIVE_HIGH>; > + compatible = "sdw10217020200"; You ordered the properties in a different manner in a node right before this one, even though they are almost identical. Please keep them coherent and put compatible® at the top. Konrad > + reg = <0 2>; > + #thermal-sensor-cells = <0>; > + sound-name-prefix = "SpkrRight"; > + #sound-dai-cells = <0>; > + vdd-supply = <&vreg_s10b>; > + }; > +}; > + > + > +&swr1 { > + status = "okay"; > + > + wcd_rx: wcd9380-rx@0,4 { > + compatible = "sdw20217010d00"; > + reg = <0 4>; > + qcom,rx-port-mapping = <1 2 3 4 5 6>; > + > + }; > +}; > + > +&swr2 { > + status = "okay"; > + > + wcd_tx: wcd9380-tx@0,3 { > + compatible = "sdw20217010d00"; > + reg = <0 3>; > + qcom,tx-port-mapping = <1 1 2 3>; > + }; > +}; > + > +&vamacro { > + pinctrl-0 = <&dmic01_active>, <&dmic02_active>; > + pinctrl-names = "default"; > + vdd-micb-supply = <&vreg_s10b>; > + qcom,dmic-sample-rate = <600000>; > +}; > + > &tlmm { > gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>; > > + wcd_default: wcd-default-state { > + reset { > + pins = "gpio106"; > + function = "gpio"; > + bias-disable; > + }; > + }; > + > kybd_default: kybd-default-state { > disable { > pins = "gpio102"; > @@ -383,6 +576,26 @@ qup2_i2c5_default: qup2-i2c5-default-state { > drive-strength = <16>; > }; > > + spkr_1_sd_n_active: spkr_1_sd_n_active { > + perst-n { > + pins = "gpio178"; > + function = "gpio"; > + drive-strength = <16>; > + bias-disable; > + output-high; > + }; > + }; > + > + spkr_2_sd_n_active: spkr_2_sd_n_active { > + perst-n { > + pins = "gpio179"; > + function = "gpio"; > + drive-strength = <16>; > + bias-disable; > + output-high; > + }; > + }; > + > tpad_default: tpad-default-state { > int-n { > pins = "gpio182";
On 15/11/2022 18:02, Srinivas Kandagatla wrote: > Add support for SoundCard on X13s. This patch adds support for Headset > Playback, record and 2 DMICs on the Panel along with the regulators > required for powering up the LPASS codecs. > > Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > --- > .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 213 ++++++++++++++++++ > 1 file changed, 213 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts > index b2b744bb8a53..99c3021e8149 100644 > --- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts > +++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts > @@ -58,6 +58,16 @@ vreg_misc_3p3: regulator-misc-3p3 { > regulator-boot-on; > regulator-always-on; > }; > + > + vph_pwr: vph-pwr-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "VPH_VCC3R9"; > + regulator-min-microvolt = <3900000>; > + regulator-max-microvolt = <3900000>; > + > + regulator-always-on; > + regulator-boot-on; > + }; > }; > > &apps_rsc { > @@ -67,6 +77,13 @@ pmc8280-1-rpmh-regulators { > > vdd-l3-l5-supply = <&vreg_s11b>; > > + vreg_s10b: smps10 { > + regulator-name = "vreg_s10b"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > vreg_s11b: smps11 { > regulator-name = "vreg_s11b"; > regulator-min-microvolt = <1272000>; > @@ -74,6 +91,13 @@ vreg_s11b: smps11 { > regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > }; > > + vreg_s12b: smps12 { > + regulator-name = "vreg_s12b"; > + regulator-min-microvolt = <984000>; > + regulator-max-microvolt = <984000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > vreg_l3b: ldo3 { > regulator-name = "vreg_l3b"; > regulator-min-microvolt = <1200000>; > @@ -102,6 +126,7 @@ vreg_l6b: ldo6 { > pmc8280c-rpmh-regulators { > compatible = "qcom,pm8350c-rpmh-regulators"; > qcom,pmic-id = "c"; > + vdd-bob-supply = <&vph_pwr>; > > vreg_l1c: ldo1 { > regulator-name = "vreg_l1c"; > @@ -123,6 +148,13 @@ vreg_l13c: ldo13 { > regulator-max-microvolt = <3072000>; > regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > }; > + > + vreg_bob: bob { > + regulator-name = "vreg_bob"; > + regulator-min-microvolt = <3008000>; > + regulator-max-microvolt = <3960000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; > + }; > }; > > pmc8280-2-rpmh-regulators { > @@ -268,6 +300,80 @@ &remoteproc_nsp0 { > status = "okay"; > }; > > +&sound { > + compatible = "qcom,sc8280xp-sndcard"; > + model = "SC8280XP-LENOVO-X13S"; > + audio-routing = > + "SpkrLeft IN", "WSA_SPK1 OUT", > + "SpkrRight IN", "WSA_SPK2 OUT", > + "IN1_HPHL", "HPHL_OUT", > + "IN2_HPHR", "HPHR_OUT", > + "AMIC2", "MIC BIAS2", > + "VA DMIC0", "MIC BIAS1", > + "VA DMIC1", "MIC BIAS1", > + "VA DMIC2", "MIC BIAS3", > + "TX DMIC0", "MIC BIAS1", > + "TX DMIC1", "MIC BIAS2", > + "TX DMIC2", "MIC BIAS3", > + "TX SWR_ADC1", "ADC2_OUTPUT"; > + > + wcd-playback-dai-link { > + link-name = "WCD Playback"; > + cpu { > + sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>; Drop double-space > + }; Blank line > + codec { > + sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>; > + }; Blank line > + platform { > + sound-dai = <&q6apm>; > + }; > + }; Wrong indentation. > + > + wcd-capture-dai-link { > + link-name = "WCD Capture"; > + cpu { > + sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; Drop double-space > + }; > + > + codec { > + sound-dai = <&wcd938x 1>, <&swr2 0>, <&txmacro 0>; > + }; Blank line > + platform { > + sound-dai = <&q6apm>; > + }; > + }; > + > + wsa-dai-link { > + link-name = "WSA Playback"; > + cpu { > + sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>; > + }; > + > + codec { > + sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>; > + }; Blank line > + platform { > + sound-dai = <&q6apm>; > + }; > + }; > + > + va-dai-link { > + link-name = "VA Capture"; > + cpu { > + sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; > + }; > + > + platform { > + sound-dai = <&q6apm>; > + }; > + > + codec { > + sound-dai = <&vamacro 0>; > + }; > + }; > +}; > + > &usb_0 { > status = "okay"; > }; > @@ -346,9 +452,96 @@ edp_bl_pwm: edp-bl-pwm-state { > }; > }; > > +&soc { > + wcd938x: codec { > + compatible = "qcom,wcd9380-codec"; > + #sound-dai-cells = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&wcd_default>; > + reset-gpios = <&tlmm 106 0>; Use GPIO flags. This also has to be changed to ACTIVE LOW actually: https://lore.kernel.org/all/20221116053817.2929810-11-dmitry.torokhov@gmail.com/ > + > + vdd-buck-supply = <&vreg_s10b>; > + vdd-rxtx-supply = <&vreg_s10b>; > + vdd-io-supply = <&vreg_s10b>; > + vdd-mic-bias-supply = <&vreg_bob>; > + qcom,micbias1-microvolt = <1800000>; > + qcom,micbias2-microvolt = <1800000>; > + qcom,micbias3-microvolt = <1800000>; > + qcom,micbias4-microvolt = <1800000>; > + qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>; > + qcom,mbhc-headset-vthreshold-microvolt = <1700000>; > + qcom,mbhc-headphone-vthreshold-microvolt = <50000>; > + qcom,rx-device = <&wcd_rx>; > + qcom,tx-device = <&wcd_tx>; > + }; > +}; > + > +&swr0 { > + left_spkr: wsa8830-left@0,1 { > + compatible = "sdw10217020200"; > + pinctrl-names = "default"; > + pinctrl-0 = <&spkr_1_sd_n_active>; > + powerdown-gpios = <&tlmm 178 GPIO_ACTIVE_HIGH>; ACTIVE_LOW > + reg = <0 1>; reg is always second property > + #thermal-sensor-cells = <0>; > + sound-name-prefix = "SpkrLeft"; > + #sound-dai-cells = <0>; > + vdd-supply = <&vreg_s10b>; > + }; > + > + right_spkr: wsa8830-right@0,2{ > + pinctrl-names = "default"; > + pinctrl-0 = <&spkr_2_sd_n_active>; > + powerdown-gpios = <&tlmm 179 GPIO_ACTIVE_HIGH>; ACTIVE_LOW > + compatible = "sdw10217020200"; > + reg = <0 2>; > + #thermal-sensor-cells = <0>; > + sound-name-prefix = "SpkrRight"; > + #sound-dai-cells = <0>; > + vdd-supply = <&vreg_s10b>; > + }; > +}; > + > + > +&swr1 { > + status = "okay"; > + > + wcd_rx: wcd9380-rx@0,4 { > + compatible = "sdw20217010d00"; > + reg = <0 4>; > + qcom,rx-port-mapping = <1 2 3 4 5 6>; Does not look like you tested the DTS against bindings. Please run `make dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst for instructions). > + > + }; > +}; > + > +&swr2 { > + status = "okay"; > + > + wcd_tx: wcd9380-tx@0,3 { > + compatible = "sdw20217010d00"; > + reg = <0 3>; > + qcom,tx-port-mapping = <1 1 2 3>; > + }; > +}; > + > +&vamacro { > + pinctrl-0 = <&dmic01_active>, <&dmic02_active>; > + pinctrl-names = "default"; > + vdd-micb-supply = <&vreg_s10b>; > + qcom,dmic-sample-rate = <600000>; > +}; > + > &tlmm { > gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>; > > + wcd_default: wcd-default-state { > + reset { Does not look like you tested the DTS against bindings. Please run `make dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst for instructions). > + pins = "gpio106"; > + function = "gpio"; > + bias-disable; > + }; > + }; > + > kybd_default: kybd-default-state { > disable { > pins = "gpio102"; > @@ -383,6 +576,26 @@ qup2_i2c5_default: qup2-i2c5-default-state { > drive-strength = <16>; > }; > > + spkr_1_sd_n_active: spkr_1_sd_n_active { No underscores, missing state suffix. Best regards, Krzysztof
On Tue, Nov 15, 2022 at 05:02:42PM +0000, Srinivas Kandagatla wrote: > Add support for SoundCard on X13s. This patch adds support for Headset > Playback, record and 2 DMICs on the Panel along with the regulators > required for powering up the LPASS codecs. > > Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > --- > .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 213 ++++++++++++++++++ > 1 file changed, 213 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts > index b2b744bb8a53..99c3021e8149 100644 > --- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts > +++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts > @@ -58,6 +58,16 @@ vreg_misc_3p3: regulator-misc-3p3 { > regulator-boot-on; > regulator-always-on; > }; > + > + vph_pwr: vph-pwr-regulator { Use "regulator-" as a name prefix, and add "vreg_" as label prefix for consistency: vreg_vph_pwr: regulator-vph-pwr { > + compatible = "regulator-fixed"; > + regulator-name = "VPH_VCC3R9"; > + regulator-min-microvolt = <3900000>; > + regulator-max-microvolt = <3900000>; > + > + regulator-always-on; > + regulator-boot-on; > + }; > }; Johan
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts index b2b744bb8a53..99c3021e8149 100644 --- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts +++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts @@ -58,6 +58,16 @@ vreg_misc_3p3: regulator-misc-3p3 { regulator-boot-on; regulator-always-on; }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "VPH_VCC3R9"; + regulator-min-microvolt = <3900000>; + regulator-max-microvolt = <3900000>; + + regulator-always-on; + regulator-boot-on; + }; }; &apps_rsc { @@ -67,6 +77,13 @@ pmc8280-1-rpmh-regulators { vdd-l3-l5-supply = <&vreg_s11b>; + vreg_s10b: smps10 { + regulator-name = "vreg_s10b"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + vreg_s11b: smps11 { regulator-name = "vreg_s11b"; regulator-min-microvolt = <1272000>; @@ -74,6 +91,13 @@ vreg_s11b: smps11 { regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; + vreg_s12b: smps12 { + regulator-name = "vreg_s12b"; + regulator-min-microvolt = <984000>; + regulator-max-microvolt = <984000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + vreg_l3b: ldo3 { regulator-name = "vreg_l3b"; regulator-min-microvolt = <1200000>; @@ -102,6 +126,7 @@ vreg_l6b: ldo6 { pmc8280c-rpmh-regulators { compatible = "qcom,pm8350c-rpmh-regulators"; qcom,pmic-id = "c"; + vdd-bob-supply = <&vph_pwr>; vreg_l1c: ldo1 { regulator-name = "vreg_l1c"; @@ -123,6 +148,13 @@ vreg_l13c: ldo13 { regulator-max-microvolt = <3072000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; + + vreg_bob: bob { + regulator-name = "vreg_bob"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + }; }; pmc8280-2-rpmh-regulators { @@ -268,6 +300,80 @@ &remoteproc_nsp0 { status = "okay"; }; +&sound { + compatible = "qcom,sc8280xp-sndcard"; + model = "SC8280XP-LENOVO-X13S"; + audio-routing = + "SpkrLeft IN", "WSA_SPK1 OUT", + "SpkrRight IN", "WSA_SPK2 OUT", + "IN1_HPHL", "HPHL_OUT", + "IN2_HPHR", "HPHR_OUT", + "AMIC2", "MIC BIAS2", + "VA DMIC0", "MIC BIAS1", + "VA DMIC1", "MIC BIAS1", + "VA DMIC2", "MIC BIAS3", + "TX DMIC0", "MIC BIAS1", + "TX DMIC1", "MIC BIAS2", + "TX DMIC2", "MIC BIAS3", + "TX SWR_ADC1", "ADC2_OUTPUT"; + + wcd-playback-dai-link { + link-name = "WCD Playback"; + cpu { + sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>; + }; + codec { + sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>; + }; + platform { + sound-dai = <&q6apm>; + }; + }; + + wcd-capture-dai-link { + link-name = "WCD Capture"; + cpu { + sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; + }; + + codec { + sound-dai = <&wcd938x 1>, <&swr2 0>, <&txmacro 0>; + }; + platform { + sound-dai = <&q6apm>; + }; + }; + + wsa-dai-link { + link-name = "WSA Playback"; + cpu { + sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>; + }; + + codec { + sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>; + }; + platform { + sound-dai = <&q6apm>; + }; + }; + + va-dai-link { + link-name = "VA Capture"; + cpu { + sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; + }; + + platform { + sound-dai = <&q6apm>; + }; + + codec { + sound-dai = <&vamacro 0>; + }; + }; +}; + &usb_0 { status = "okay"; }; @@ -346,9 +452,96 @@ edp_bl_pwm: edp-bl-pwm-state { }; }; +&soc { + wcd938x: codec { + compatible = "qcom,wcd9380-codec"; + #sound-dai-cells = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&wcd_default>; + reset-gpios = <&tlmm 106 0>; + + vdd-buck-supply = <&vreg_s10b>; + vdd-rxtx-supply = <&vreg_s10b>; + vdd-io-supply = <&vreg_s10b>; + vdd-mic-bias-supply = <&vreg_bob>; + qcom,micbias1-microvolt = <1800000>; + qcom,micbias2-microvolt = <1800000>; + qcom,micbias3-microvolt = <1800000>; + qcom,micbias4-microvolt = <1800000>; + qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>; + qcom,mbhc-headset-vthreshold-microvolt = <1700000>; + qcom,mbhc-headphone-vthreshold-microvolt = <50000>; + qcom,rx-device = <&wcd_rx>; + qcom,tx-device = <&wcd_tx>; + }; +}; + +&swr0 { + left_spkr: wsa8830-left@0,1 { + compatible = "sdw10217020200"; + pinctrl-names = "default"; + pinctrl-0 = <&spkr_1_sd_n_active>; + powerdown-gpios = <&tlmm 178 GPIO_ACTIVE_HIGH>; + reg = <0 1>; + #thermal-sensor-cells = <0>; + sound-name-prefix = "SpkrLeft"; + #sound-dai-cells = <0>; + vdd-supply = <&vreg_s10b>; + }; + + right_spkr: wsa8830-right@0,2{ + pinctrl-names = "default"; + pinctrl-0 = <&spkr_2_sd_n_active>; + powerdown-gpios = <&tlmm 179 GPIO_ACTIVE_HIGH>; + compatible = "sdw10217020200"; + reg = <0 2>; + #thermal-sensor-cells = <0>; + sound-name-prefix = "SpkrRight"; + #sound-dai-cells = <0>; + vdd-supply = <&vreg_s10b>; + }; +}; + + +&swr1 { + status = "okay"; + + wcd_rx: wcd9380-rx@0,4 { + compatible = "sdw20217010d00"; + reg = <0 4>; + qcom,rx-port-mapping = <1 2 3 4 5 6>; + + }; +}; + +&swr2 { + status = "okay"; + + wcd_tx: wcd9380-tx@0,3 { + compatible = "sdw20217010d00"; + reg = <0 3>; + qcom,tx-port-mapping = <1 1 2 3>; + }; +}; + +&vamacro { + pinctrl-0 = <&dmic01_active>, <&dmic02_active>; + pinctrl-names = "default"; + vdd-micb-supply = <&vreg_s10b>; + qcom,dmic-sample-rate = <600000>; +}; + &tlmm { gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>; + wcd_default: wcd-default-state { + reset { + pins = "gpio106"; + function = "gpio"; + bias-disable; + }; + }; + kybd_default: kybd-default-state { disable { pins = "gpio102"; @@ -383,6 +576,26 @@ qup2_i2c5_default: qup2-i2c5-default-state { drive-strength = <16>; }; + spkr_1_sd_n_active: spkr_1_sd_n_active { + perst-n { + pins = "gpio178"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + output-high; + }; + }; + + spkr_2_sd_n_active: spkr_2_sd_n_active { + perst-n { + pins = "gpio179"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + output-high; + }; + }; + tpad_default: tpad-default-state { int-n { pins = "gpio182";
Add support for SoundCard on X13s. This patch adds support for Headset Playback, record and 2 DMICs on the Panel along with the regulators required for powering up the LPASS codecs. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> --- .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 213 ++++++++++++++++++ 1 file changed, 213 insertions(+)