| Message ID | 20230608-b4-add-burst-mode-v1-1-55dfbcfada55@quicinc.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | drm/msm/dsi: Enable BURST_MODE for command mode for DSI 6G v1.3+ | expand |
On 13/06/2023 02:37, Jessica Zhang wrote: > During a frame transfer in command mode, there could be frequent > LP11 <-> HS transitions when multiple DCS commands are sent mid-frame or > if the DSI controller is running on slow clock and is throttled. To > minimize frame latency due to these transitions, it is recommended to > send the frame in a single burst. > > This feature is supported for DSI 6G 1.3 and above, thus enable burst > mode if supported. > > Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com> > --- > drivers/gpu/drm/msm/dsi/dsi_host.c | 5 +++++ > 1 file changed, 5 insertions(+) > > diff --git a/drivers/gpu/drm/msm/dsi/dsi_host.c b/drivers/gpu/drm/msm/dsi/dsi_host.c > index 744f2398a6d6..8254b06dca85 100644 > --- a/drivers/gpu/drm/msm/dsi/dsi_host.c > +++ b/drivers/gpu/drm/msm/dsi/dsi_host.c > @@ -994,6 +994,11 @@ static void dsi_timing_setup(struct msm_dsi_host *msm_host, bool is_bonded_dsi) > dsi_write(msm_host, REG_DSI_CMD_MDP_STREAM0_TOTAL, > DSI_CMD_MDP_STREAM0_TOTAL_H_TOTAL(hdisplay) | > DSI_CMD_MDP_STREAM0_TOTAL_V_TOTAL(mode->vdisplay)); > + > + if (msm_host->cfg_hnd->major == MSM_DSI_VER_MAJOR_6G && > + msm_host->cfg_hnd->minor >= MSM_DSI_6G_VER_MINOR_V1_3) > + dsi_write(msm_host, REG_DSI_CMD_MODE_MDP_CTRL2, > + DSI_CMD_MODE_MDP_CTRL2_BURST_MODE); Please move this to dsi_ctrl_config(), the place where we set all the configs. Also please change this to RMW cycle. > } > } > > > --- > base-commit: dd969f852ba4c66938c71889e826aa8e5300d2f2 > change-id: 20230608-b4-add-burst-mode-a5bb144069fa > > Best regards,
diff --git a/drivers/gpu/drm/msm/dsi/dsi_host.c b/drivers/gpu/drm/msm/dsi/dsi_host.c index 744f2398a6d6..8254b06dca85 100644 --- a/drivers/gpu/drm/msm/dsi/dsi_host.c +++ b/drivers/gpu/drm/msm/dsi/dsi_host.c @@ -994,6 +994,11 @@ static void dsi_timing_setup(struct msm_dsi_host *msm_host, bool is_bonded_dsi) dsi_write(msm_host, REG_DSI_CMD_MDP_STREAM0_TOTAL, DSI_CMD_MDP_STREAM0_TOTAL_H_TOTAL(hdisplay) | DSI_CMD_MDP_STREAM0_TOTAL_V_TOTAL(mode->vdisplay)); + + if (msm_host->cfg_hnd->major == MSM_DSI_VER_MAJOR_6G && + msm_host->cfg_hnd->minor >= MSM_DSI_6G_VER_MINOR_V1_3) + dsi_write(msm_host, REG_DSI_CMD_MODE_MDP_CTRL2, + DSI_CMD_MODE_MDP_CTRL2_BURST_MODE); } }
During a frame transfer in command mode, there could be frequent LP11 <-> HS transitions when multiple DCS commands are sent mid-frame or if the DSI controller is running on slow clock and is throttled. To minimize frame latency due to these transitions, it is recommended to send the frame in a single burst. This feature is supported for DSI 6G 1.3 and above, thus enable burst mode if supported. Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com> --- drivers/gpu/drm/msm/dsi/dsi_host.c | 5 +++++ 1 file changed, 5 insertions(+) --- base-commit: dd969f852ba4c66938c71889e826aa8e5300d2f2 change-id: 20230608-b4-add-burst-mode-a5bb144069fa Best regards,