diff mbox series

[v2,2/2] i2c: rcar: improve accuracy for R-Car Gen3+

Message ID 20230919151948.21564-3-wsa+renesas@sang-engineering.com
State Superseded
Headers show
Series i2c: rcar: improve Gen3 support | expand

Commit Message

Wolfram Sang Sept. 19, 2023, 3:19 p.m. UTC 
With some new registers, SCL can be calculated to be closer to the
desired rate. Apply the new formula for R-Car Gen3 device types.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
---

Changes since v1:
* fixed two whitespace issues
* use dedicated variables for scld and schd
* explicitly say "2 * smd" in the comment explaining the new formula
* use correct division 'clkp/SCL' in the same comment
* updated debug printout to use the new variables

For all of these, thanks Geert!

 drivers/i2c/busses/i2c-rcar.c | 128 +++++++++++++++++++++++-----------
 1 file changed, 89 insertions(+), 39 deletions(-)

Comments

Geert Uytterhoeven Sept. 20, 2023, 9:47 a.m. UTC | #1 
Hi Wolfram,

On Tue, Sep 19, 2023 at 8:45 PM Wolfram Sang
<wsa+renesas@sang-engineering.com> wrote:
> With some new registers, SCL can be calculated to be closer to the
> desired rate. Apply the new formula for R-Car Gen3 device types.
>
> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
> ---
>
> Changes since v1:
> * fixed two whitespace issues
> * use dedicated variables for scld and schd
> * explicitly say "2 * smd" in the comment explaining the new formula
> * use correct division 'clkp/SCL' in the same comment
> * updated debug printout to use the new variables

Thanks for the update!

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

But given you have to respin 1/2 anyway, what about...

> --- a/drivers/i2c/busses/i2c-rcar.c
> +++ b/drivers/i2c/busses/i2c-rcar.c

> @@ -128,6 +146,8 @@ struct rcar_i2c_priv {
>
>         int pos;
>         u32 icccr;
> +       u16 scld;
> +       u16 schd;

... changing the order, to match alphabetical and register offset order.

> +
> +               priv->icccr = cdf;
> +               priv->scld = RCAR_SCLD_RATIO * x;
> +               priv->schd = RCAR_SCHD_RATIO * x;

Likewise.

> +
> +               dev_dbg(dev, "clk %u/%u(%lu), round %u, CDF: %u SCLD %u SCHD %u\n",
> +                       scl, t.bus_freq_hz, rate, round, cdf, priv->scld, priv->schd);
> +       }
>
>         return 0;

Gr{oetje,eeting}s,

                        Geert
diff mbox series

Patch

diff --git a/drivers/i2c/busses/i2c-rcar.c b/drivers/i2c/busses/i2c-rcar.c
index bb4fc66309c2..b6b610011e84 100644
--- a/drivers/i2c/busses/i2c-rcar.c
+++ b/drivers/i2c/busses/i2c-rcar.c
@@ -41,6 +41,10 @@ 
 #define ICSAR	0x1C	/* slave address */
 #define ICMAR	0x20	/* master address */
 #define ICRXTX	0x24	/* data port */
+#define ICCCR2	0x28	/* Clock control 2 */
+#define ICMPR	0x2C	/* SCL mask control */
+#define ICHPR	0x30	/* SCL HIGH control */
+#define ICLPR	0x34	/* SCL LOW control */
 #define ICFBSCR	0x38	/* first bit setup cycle (Gen3) */
 #define ICDMAER	0x3c	/* DMA enable (Gen3) */
 
@@ -84,11 +88,25 @@ 
 #define RMDMAE	BIT(1)	/* DMA Master Received Enable */
 #define TMDMAE	BIT(0)	/* DMA Master Transmitted Enable */
 
+/* ICCCR2 */
+#define CDFD	BIT(2)	/* CDF Disable */
+#define HLSE	BIT(1)	/* HIGH/LOW Separate Control Enable */
+#define SME	BIT(0)	/* SCL Mask Enable */
+
 /* ICFBSCR */
 #define TCYC17	0x0f		/* 17*Tcyc delay 1st bit between SDA and SCL */
 
 #define RCAR_MIN_DMA_LEN	8
 
+/* SCL low/high ratio 5:4 to meet all I2C timing specs (incl safety margin) */
+#define RCAR_SCLD_RATIO		5
+#define RCAR_SCHD_RATIO		4
+/*
+ * SMD should be smaller than SCLD/SCHD and is always around 20 in the docs.
+ * Thus, we simply use 20 which works for low and high speeds.
+ */
+#define RCAR_DEFAULT_SMD	20
+
 #define RCAR_BUS_PHASE_START	(MDBS | MIE | ESG)
 #define RCAR_BUS_PHASE_DATA	(MDBS | MIE)
 #define RCAR_BUS_PHASE_STOP	(MDBS | MIE | FSB)
@@ -128,6 +146,8 @@  struct rcar_i2c_priv {
 
 	int pos;
 	u32 icccr;
+	u16 scld;
+	u16 schd;
 	u8 recovery_icmcr;	/* protected by adapter lock */
 	enum rcar_i2c_type devtype;
 	struct i2c_client *slave;
@@ -216,11 +236,16 @@  static void rcar_i2c_init(struct rcar_i2c_priv *priv)
 	rcar_i2c_write(priv, ICMCR, MDBS);
 	rcar_i2c_write(priv, ICMSR, 0);
 	/* start clock */
-	rcar_i2c_write(priv, ICCCR, priv->icccr);
-
-	if (priv->devtype == I2C_RCAR_GEN3)
+	if (priv->devtype < I2C_RCAR_GEN3) {
+		rcar_i2c_write(priv, ICCCR, priv->icccr);
+	} else {
+		rcar_i2c_write(priv, ICCCR2, CDFD | HLSE | SME);
+		rcar_i2c_write(priv, ICCCR, priv->icccr);
+		rcar_i2c_write(priv, ICMPR, RCAR_DEFAULT_SMD);
+		rcar_i2c_write(priv, ICHPR, priv->schd);
+		rcar_i2c_write(priv, ICLPR, priv->scld);
 		rcar_i2c_write(priv, ICFBSCR, TCYC17);
-
+	}
 }
 
 static int rcar_i2c_bus_barrier(struct rcar_i2c_priv *priv)
@@ -241,7 +266,7 @@  static int rcar_i2c_bus_barrier(struct rcar_i2c_priv *priv)
 
 static int rcar_i2c_clock_calculate(struct rcar_i2c_priv *priv)
 {
-	u32 scgd, cdf, round, ick, sum, scl, cdf_width;
+	u32 cdf, round, ick, sum, scl, cdf_width;
 	unsigned long rate;
 	struct device *dev = rcar_i2c_priv_to_dev(priv);
 	struct i2c_timings t = {
@@ -254,27 +279,17 @@  static int rcar_i2c_clock_calculate(struct rcar_i2c_priv *priv)
 	/* Fall back to previously used values if not supplied */
 	i2c_parse_fw_timings(dev, &t, false);
 
-	switch (priv->devtype) {
-	case I2C_RCAR_GEN1:
-		cdf_width = 2;
-		break;
-	case I2C_RCAR_GEN2:
-	case I2C_RCAR_GEN3:
-		cdf_width = 3;
-		break;
-	default:
-		dev_err(dev, "device type error\n");
-		return -EIO;
-	}
-
 	/*
 	 * calculate SCL clock
 	 * see
-	 *	ICCCR
+	 *	ICCCR (and ICCCR2 for Gen3+)
 	 *
 	 * ick	= clkp / (1 + CDF)
 	 * SCL	= ick / (20 + SCGD * 8 + F[(ticf + tr + intd) * ick])
 	 *
+	 * for Gen3+:
+	 * SCL	= clkp / (8 + SMD * 2 + SCLD + SCHD +F[(ticf + tr + intd) * clkp])
+	 *
 	 * ick  : I2C internal clock < 20 MHz
 	 * ticf : I2C SCL falling time
 	 * tr   : I2C SCL rising  time
@@ -284,11 +299,12 @@  static int rcar_i2c_clock_calculate(struct rcar_i2c_priv *priv)
 	 */
 	rate = clk_get_rate(priv->clk);
 	cdf = rate / 20000000;
-	if (cdf >= 1U << cdf_width) {
-		dev_err(dev, "Input clock %lu too high\n", rate);
-		return -EIO;
-	}
-	ick = rate / (cdf + 1);
+	cdf_width = (priv->devtype == I2C_RCAR_GEN1) ? 2 : 3;
+	if (cdf >= 1U << cdf_width)
+		goto err_no_val;
+
+	/* On Gen3+, we use cdf only for the filters, not as a SCL divider */
+	ick = rate / (priv->devtype < I2C_RCAR_GEN3 ? (cdf + 1) : 1);
 
 	/*
 	 * It is impossible to calculate a large scale number on u32. Separate it.
@@ -301,24 +317,58 @@  static int rcar_i2c_clock_calculate(struct rcar_i2c_priv *priv)
 	round = DIV_ROUND_CLOSEST(ick, 1000000);
 	round = DIV_ROUND_CLOSEST(round * sum, 1000);
 
-	/*
-	 * SCL	= ick / (20 + 8 * SCGD + F[(ticf + tr + intd) * ick])
-	 * 20 + 8 * SCGD + F[...] = ick / SCL
-	 * SCGD = ((ick / SCL) - 20 - F[...]) / 8
-	 * Result (= SCL) should be less than bus_speed for hardware safety
-	 */
-	scgd = DIV_ROUND_UP(ick, t.bus_freq_hz ?: 1);
-	scgd = DIV_ROUND_UP(scgd - 20 - round, 8);
-	scl = ick / (20 + 8 * scgd + round);
+	if (priv->devtype < I2C_RCAR_GEN3) {
+		u32 scgd;
+		/*
+		 * SCL	= ick / (20 + 8 * SCGD + F[(ticf + tr + intd) * ick])
+		 * 20 + 8 * SCGD + F[...] = ick / SCL
+		 * SCGD = ((ick / SCL) - 20 - F[...]) / 8
+		 * Result (= SCL) should be less than bus_speed for hardware safety
+		 */
+		scgd = DIV_ROUND_UP(ick, t.bus_freq_hz ?: 1);
+		scgd = DIV_ROUND_UP(scgd - 20 - round, 8);
+		scl = ick / (20 + 8 * scgd + round);
 
-	if (scgd > 0x3f)
-		goto err_no_val;
+		if (scgd > 0x3f)
+			goto err_no_val;
 
-	dev_dbg(dev, "clk %u/%u(%lu), round %u, CDF: %u, SCGD: %u\n",
-		scl, t.bus_freq_hz, rate, round, cdf, scgd);
+		dev_dbg(dev, "clk %u/%u(%lu), round %u, CDF: %u, SCGD: %u\n",
+			scl, t.bus_freq_hz, rate, round, cdf, scgd);
 
-	/* keep icccr value */
-	priv->icccr = scgd << cdf_width | cdf;
+		priv->icccr = scgd << cdf_width | cdf;
+	} else {
+		u32 x, sum_ratio = RCAR_SCHD_RATIO + RCAR_SCLD_RATIO;
+		/*
+		 * SCLD/SCHD ratio and SMD default value are explained above
+		 * where they are defined. With these definitions, we can compute
+		 * x as a base value for the SCLD/SCHD ratio:
+		 *
+		 * SCL = clkp / (8 + 2 * SMD + SCLD + SCHD + F[(ticf + tr + intd) * clkp])
+		 * SCL = clkp / (8 + 2 * RCAR_DEFAULT_SMD + RCAR_SCLD_RATIO * x
+		 *		 + RCAR_SCHD_RATIO * x + F[...])
+		 *
+		 * with: sum_ratio = RCAR_SCLD_RATIO + RCAR_SCHD_RATIO
+		 * and:  smd = RCAR_DEFAULT_SMD
+		 *
+		 * SCL = clkp / (8 + 2 * smd + sum_ratio * x + F[...])
+		 * 8 + 2 * smd + sum_ratio * x + F[...] = clkp / SCL
+		 * x = ((clkp / SCL) - 8 - 2 * smd - F[...]) / sum_ratio
+		 */
+		x = DIV_ROUND_UP(rate, t.bus_freq_hz ?: 1);
+		x = DIV_ROUND_UP(x - 8 - 2 * RCAR_DEFAULT_SMD - round, sum_ratio);
+		scl = rate / (8 + 2 * RCAR_DEFAULT_SMD + sum_ratio * x + round);
+
+		/* Bail out if values don't fit into 16 bit or SMD became too large */
+		if (x * RCAR_SCLD_RATIO > 0xffff || RCAR_DEFAULT_SMD > x * RCAR_SCHD_RATIO)
+			goto err_no_val;
+
+		priv->icccr = cdf;
+		priv->scld = RCAR_SCLD_RATIO * x;
+		priv->schd = RCAR_SCHD_RATIO * x;
+
+		dev_dbg(dev, "clk %u/%u(%lu), round %u, CDF: %u SCLD %u SCHD %u\n",
+			scl, t.bus_freq_hz, rate, round, cdf, priv->scld, priv->schd);
+	}
 
 	return 0;