diff mbox series

[08/13] arm64: dts: qcom: msm8916-asus-z00l: Add sound and modem

Message ID 20230926-msm8916-modem-v1-8-398eec74bac9@gerhold.net
State Superseded
Headers show
Series arm64: dts: qcom: msm8916/39: Enable sound and modem with QDSP6 | expand

Commit Message

Stephan Gerhold Sept. 26, 2023, 4:51 p.m. UTC 
From: "J.R. Divya Antony" <d.antony.jr@gmail.com>

Enable sound and modem for the ASUS Zenfone 2 Laser. The setup is
similar to most MSM8916 devices, i.e.:

 - QDSP6 audio
 - Speakear/earpiece/headphones/microphones via digital/analog codec
   in MSM8916/PM8916
 - Audio jack detection via analog codec in PM8916
 - WWAN Internet via BAM-DMUX

Signed-off-by: J.R. Divya Antony <d.antony.jr@gmail.com>
[Stephan: rebase and simplify, add consistent commit message]
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
---
 arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

Comments

Konrad Dybcio Sept. 26, 2023, 6:58 p.m. UTC | #1 
On 26.09.2023 18:51, Stephan Gerhold wrote:
> From: "J.R. Divya Antony" <d.antony.jr@gmail.com>
> 
> Enable sound and modem for the ASUS Zenfone 2 Laser. The setup is
> similar to most MSM8916 devices, i.e.:
> 
>  - QDSP6 audio
>  - Speakear/earpiece/headphones/microphones via digital/analog codec
>    in MSM8916/PM8916
>  - Audio jack detection via analog codec in PM8916
>  - WWAN Internet via BAM-DMUX
> 
> Signed-off-by: J.R. Divya Antony <d.antony.jr@gmail.com>
> [Stephan: rebase and simplify, add consistent commit message]
> Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts b/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts
index a8be6ff66893..ff8eb0a94795 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts
@@ -3,6 +3,8 @@ 
 /dts-v1/;
 
 #include "msm8916-pm8916.dtsi"
+#include "msm8916-modem-qdsp6.dtsi"
+
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
@@ -130,6 +132,18 @@  &blsp_uart2 {
 	status = "okay";
 };
 
+&mpss_mem {
+	reg = <0x0 0x86800000 0x0 0x5500000>;
+};
+
+&pm8916_codec {
+	qcom,micbias-lvl = <2800>;
+	qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
+	qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
+	qcom,micbias1-ext-cap;
+	qcom,hphl-jack-type-normally-open;
+};
+
 &pm8916_rpm_regulators {
 	pm8916_l17: l17 {
 		regulator-min-microvolt = <2850000>;
@@ -151,6 +165,14 @@  &sdhc_2 {
 	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
 };
 
+&sound {
+	status = "okay";
+	audio-routing =
+		"AMIC1", "MIC BIAS External1",
+		"AMIC2", "MIC BIAS Internal2",
+		"AMIC3", "MIC BIAS External1";
+};
+
 &usb {
 	status = "okay";
 	extcon = <&usb_id>, <&usb_id>;