| Message ID | TYAP286MB0315F4D71698370875F58F6EBCAAA@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM |
|---|---|
| State | New |
| Headers | show |
| Series | [v4] dt-bindings: leds: add 'internet' and 'signal' function definitions | expand |
On Thu, Nov 23, 2023 at 11:25:43AM +0000, Lee Jones wrote: > Andrew, Florian, > > Thoughts? Hi Lee Thanks for forwarding this. > On Mon, 06 Nov 2023, Shiji Yang wrote: > > > These two types of LEDs are widely used in routers and NICs. I would disagree with this. Routers and NICs are very generic terms. The Cisco router i have in the broom closet does not have a signal strength. It does not even have WiFi. It has no concept of Internet. I would drop NIC and add more words to narrow routers down to a more specific class of routers, probably those found in homes, rented from an ISP, most don't actually do L3 routing, or at best, just NAT. > > The 'signal' LED is used to display the wireless signal strength. > > Usually, there are 3~4 LEDs in one group to indicate the signal > > strength, similar to the signal icon on a mobile phone. Maybe signal_strength. And is there any reason these cannot be used on a 5G modem to indicate 'mobile phone' like signal strength? So `similar to` is wrong, they could actually be used for that. At least the word wireless is used, not wifi. So its reasonably generic. Are there other signal strength indicators for other media? I've not seen powerline modems have such indicators. And with those SNR is more important than signal strength. > > The 'internet' LED can indicate whether the device can access a > > specific server. It's different from 'wan'. 'wan' usually indicates > > whether the WAN port is connected to the modem (internet services > > may still be unavailable). But the 'internet' shows if the device > > can successfully ping servers such as 8.8.8.8 to detect the internet > > connection status. When the router is running in AP only mode, we > > can even connect LAN port to the AC/modem to connect to the internet. > > In this case, the 'internet' LED should be on. On some routers, both > > 'internet' and 'wan' are available and can be controlled separately. I suggest some of this text appears in the header, to make their meaning clear. Also, document what WAN means. But care is needed, since these are networking wide concepts, not the very narrow market of an ISP rented boxes. Andrew
diff --git a/include/dt-bindings/leds/common.h b/include/dt-bindings/leds/common.h index 9a0d33d02..f831c5dba 100644 --- a/include/dt-bindings/leds/common.h +++ b/include/dt-bindings/leds/common.h @@ -88,6 +88,7 @@ #define LED_FUNCTION_FLASH "flash" #define LED_FUNCTION_HEARTBEAT "heartbeat" #define LED_FUNCTION_INDICATOR "indicator" +#define LED_FUNCTION_INTERNET "internet" #define LED_FUNCTION_LAN "lan" #define LED_FUNCTION_MAIL "mail" #define LED_FUNCTION_MTD "mtd" @@ -95,6 +96,7 @@ #define LED_FUNCTION_PROGRAMMING "programming" #define LED_FUNCTION_RX "rx" #define LED_FUNCTION_SD "sd" +#define LED_FUNCTION_SIGNAL "signal" #define LED_FUNCTION_STANDBY "standby" #define LED_FUNCTION_TORCH "torch" #define LED_FUNCTION_TX "tx"
These two types of LEDs are widely used in routers and NICs. The 'signal' LED is used to display the wireless signal strength. Usually, there are 3~4 LEDs in one group to indicate the signal strength, similar to the signal icon on a mobile phone. The 'internet' LED can indicate whether the device can access a specific server. It's different from 'wan'. 'wan' usually indicates whether the WAN port is connected to the modem (internet services may still be unavailable). But the 'internet' shows if the device can successfully ping servers such as 8.8.8.8 to detect the internet connection status. When the router is running in AP only mode, we can even connect LAN port to the AC/modem to connect to the internet. In this case, the 'internet' LED should be on. On some routers, both 'internet' and 'wan' are available and can be controlled separately. Signed-off-by: Shiji Yang <yangshiji66@outlook.com> --- Changes in v2: * Remove the LED name sorting patch as it changes the ABI. * Add "devicetree@vger.kernel.org" to '--to' list. Thanks to Rob Herring and Krzysztof Kozlowski for letting me know I can send patch to multiple mailing list at once. Changes in v3: * Add more information about the new added LEDs. * Remove the missing LED fix as Jisheng Zhang has already sent a similar one. I should search the mailing list first... Changes in v4: * Rename 'rssi' LED to more generic name 'signal'. I forgot to update the source file in v3. v1: https://lore.kernel.org/all/TYAP286MB0315FE921FF113BF76F7B700BCA0A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM/ v2: https://lore.kernel.org/all/TYAP286MB03159A83A77E6FD59F271D9BBCA0A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM/ v3: https://lore.kernel.org/all/TYAP286MB0315AE8F62E6AB48E3F9A0DDBCA5A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM/ include/dt-bindings/leds/common.h | 2 ++ 1 file changed, 2 insertions(+)